linux/arch/arm/boot/dts/rk3229-evb.dts
Shawn Lin e6b97a47b5 ARM: dts: rockchip: clean up the abuse of disable-wp
The mmc.txt didn't explicitly say disable-wp is for SD card slot
only, but that is what it was designed for in the first place.

Remove all disable-wp from emmc or sdio controller.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-01-28 10:51:55 +01:00

253 lines
4.5 KiB
Plaintext

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/dts-v1/;
#include <dt-bindings/input/input.h>
#include "rk3229.dtsi"
/ {
model = "Rockchip RK3229 Evaluation board";
compatible = "rockchip,rk3229-evb", "rockchip,rk3229";
memory@60000000 {
device_type = "memory";
reg = <0x60000000 0x40000000>;
};
dc_12v: dc-12v-regulator {
compatible = "regulator-fixed";
regulator-name = "dc_12v";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <12000000>;
regulator-max-microvolt = <12000000>;
};
ext_gmac: ext_gmac {
compatible = "fixed-clock";
clock-frequency = <125000000>;
clock-output-names = "ext_gmac";
#clock-cells = <0>;
};
vcc_host: vcc-host-regulator {
compatible = "regulator-fixed";
enable-active-high;
gpio = <&gpio3 RK_PC4 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&host_vbus_drv>;
regulator-name = "vcc_host";
regulator-always-on;
regulator-boot-on;
vin-supply = <&vcc_sys>;
};
vcc_phy: vcc-phy-regulator {
compatible = "regulator-fixed";
enable-active-high;
regulator-name = "vcc_phy";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
vin-supply = <&vccio_1v8>;
};
vcc_sys: vcc-sys-regulator {
compatible = "regulator-fixed";
regulator-name = "vcc_sys";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
vin-supply = <&dc_12v>;
};
vccio_1v8: vccio-1v8-regulator {
compatible = "regulator-fixed";
regulator-name = "vccio_1v8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
vin-supply = <&vcc_sys>;
};
vccio_3v3: vccio-3v3-regulator {
compatible = "regulator-fixed";
regulator-name = "vccio_3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
vin-supply = <&vcc_sys>;
};
vdd_arm: vdd-arm-regulator {
compatible = "pwm-regulator";
pwms = <&pwm1 0 25000 1>;
pwm-supply = <&vcc_sys>;
regulator-name = "vdd_arm";
regulator-min-microvolt = <950000>;
regulator-max-microvolt = <1400000>;
regulator-always-on;
regulator-boot-on;
};
vdd_log: vdd-log-regulator {
compatible = "pwm-regulator";
pwms = <&pwm2 0 25000 1>;
pwm-supply = <&vcc_sys>;
regulator-name = "vdd_log";
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1300000>;
regulator-always-on;
regulator-boot-on;
};
gpio_keys {
compatible = "gpio-keys";
autorepeat;
pinctrl-names = "default";
pinctrl-0 = <&pwr_key>;
power_key: power-key {
label = "GPIO Key Power";
gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
linux,code = <KEY_POWER>;
debounce-interval = <100>;
wakeup-source;
};
};
};
&cpu0 {
cpu-supply = <&vdd_arm>;
};
&cpu1 {
cpu-supply = <&vdd_arm>;
};
&cpu2 {
cpu-supply = <&vdd_arm>;
};
&cpu3 {
cpu-supply = <&vdd_arm>;
};
&emmc {
cap-mmc-highspeed;
non-removable;
status = "okay";
};
&gmac {
assigned-clocks = <&cru SCLK_MAC_EXTCLK>, <&cru SCLK_MAC>;
assigned-clock-parents = <&ext_gmac>, <&cru SCLK_MAC_EXTCLK>;
clock_in_out = "input";
phy-supply = <&vcc_phy>;
phy-mode = "rgmii";
pinctrl-names = "default";
pinctrl-0 = <&rgmii_pins>;
snps,reset-gpio = <&gpio2 RK_PD0 GPIO_ACTIVE_LOW>;
snps,reset-active-low;
snps,reset-delays-us = <0 10000 1000000>;
tx_delay = <0x30>;
rx_delay = <0x10>;
status = "okay";
};
&io_domains {
status = "okay";
vccio1-supply = <&vccio_3v3>;
vccio2-supply = <&vccio_1v8>;
vccio4-supply = <&vccio_3v3>;
};
&pinctrl {
keys {
pwr_key: pwr-key {
rockchip,pins = <3 RK_PC7 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
usb {
host_vbus_drv: host-vbus-drv {
rockchip,pins = <3 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
};
&pwm1 {
status = "okay";
};
&pwm2 {
status = "okay";
};
&tsadc {
rockchip,hw-tshut-mode = <0>; /* tshut mode 0:CRU 1:GPIO */
status = "okay";
};
&uart2 {
status = "okay";
};
&u2phy0 {
status = "okay";
u2phy0_otg: otg-port {
status = "okay";
};
u2phy0_host: host-port {
phy-supply = <&vcc_host>;
status = "okay";
};
};
&u2phy1 {
status = "okay";
u2phy1_otg: otg-port {
phy-supply = <&vcc_host>;
status = "okay";
};
u2phy1_host: host-port {
phy-supply = <&vcc_host>;
status = "okay";
};
};
&usb_host0_ehci {
status = "okay";
};
&usb_host0_ohci {
status = "okay";
};
&usb_host1_ehci {
status = "okay";
};
&usb_host1_ohci {
status = "okay";
};
&usb_host2_ehci {
status = "okay";
};
&usb_host2_ohci {
status = "okay";
};
&usb_otg {
status = "okay";
};