mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2025-01-07 06:14:24 +08:00
a5102476a2
This has been run through Intel's LKP tests across a wide range
of modern sytems and workloads and it wasn't shown to make a
measurable performance difference positive or negative.
Now that we have some shiny new tracepoints, we can actually
figure out what the heck is going on.
During a kernel compile, 60% of the flush_tlb_mm_range() calls
are for a single page. It breaks down like this:
size percent percent<=
V V V
GLOBAL: 2.20% 2.20% avg cycles: 2283
1: 56.92% 59.12% avg cycles: 1276
2: 13.78% 72.90% avg cycles: 1505
3: 8.26% 81.16% avg cycles: 1880
4: 7.41% 88.58% avg cycles: 2447
5: 1.73% 90.31% avg cycles: 2358
6: 1.32% 91.63% avg cycles: 2563
7: 1.14% 92.77% avg cycles: 2862
8: 0.62% 93.39% avg cycles: 3542
9: 0.08% 93.47% avg cycles: 3289
10: 0.43% 93.90% avg cycles: 3570
11: 0.20% 94.10% avg cycles: 3767
12: 0.08% 94.18% avg cycles: 3996
13: 0.03% 94.20% avg cycles: 4077
14: 0.02% 94.23% avg cycles: 4836
15: 0.04% 94.26% avg cycles: 5699
16: 0.06% 94.32% avg cycles: 5041
17: 0.57% 94.89% avg cycles: 5473
18: 0.02% 94.91% avg cycles: 5396
19: 0.03% 94.95% avg cycles: 5296
20: 0.02% 94.96% avg cycles: 6749
21: 0.18% 95.14% avg cycles: 6225
22: 0.01% 95.15% avg cycles: 6393
23: 0.01% 95.16% avg cycles: 6861
24: 0.12% 95.28% avg cycles: 6912
25: 0.05% 95.32% avg cycles: 7190
26: 0.01% 95.33% avg cycles: 7793
27: 0.01% 95.34% avg cycles: 7833
28: 0.01% 95.35% avg cycles: 8253
29: 0.08% 95.42% avg cycles: 8024
30: 0.03% 95.45% avg cycles: 9670
31: 0.01% 95.46% avg cycles: 8949
32: 0.01% 95.46% avg cycles: 9350
33: 3.11% 98.57% avg cycles: 8534
34: 0.02% 98.60% avg cycles: 10977
35: 0.02% 98.62% avg cycles: 11400
We get in to dimishing returns pretty quickly. On pre-IvyBridge
CPUs, we used to set the limit at 8 pages, and it was set at 128
on IvyBrige. That 128 number looks pretty silly considering that
less than 0.5% of the flushes are that large.
The previous code tried to size this number based on the size of
the TLB. Good idea, but it's error-prone, needs maintenance
(which it didn't get up to now), and probably would not matter in
practice much.
Settting it to 33 means that we cover the mallopt
M_TRIM_THRESHOLD, which is the most universally common size to do
flushes.
That's the short version. Here's the long one for why I chose 33:
1. These numbers have a constant bias in the timestamps from the
tracing. Probably counts for a couple hundred cycles in each of
these tests, but it should be fairly _even_ across all of them.
The smallest delta between the tracepoints I have ever seen is
335 cycles. This is one reason the cycles/page cost goes down in
general as the flushes get larger. The true cost is nearer to
100 cycles.
2. A full flush is more expensive than a single invlpg, but not
by much (single percentages).
3. A dtlb miss is 17.1ns (~45 cycles) and a itlb miss is 13.0ns
(~34 cycles). At those rates, refilling the 512-entry dTLB takes
22,000 cycles.
4. 22,000 cycles is approximately the equivalent of doing 85
invlpg operations. But, the odds are that the TLB can
actually be filled up faster than that because TLB misses that
are close in time also tend to leverage the same caches.
6. ~98% of flushes are <=33 pages. There are a lot of flushes of
33 pages, probably because libc's M_TRIM_THRESHOLD is set to
128k (32 pages)
7. I've found no consistent data to support changing the IvyBridge
vs. SandyBridge tunable by a factor of 16
I used the performance counters on this hardware (IvyBridge i5-3320M)
to figure out the tlb miss costs:
ocperf.py stat -e dtlb_load_misses.walk_duration,dtlb_load_misses.walk_completed,dtlb_store_misses.walk_duration,dtlb_store_misses.walk_completed,itlb_misses.walk_duration,itlb_misses.walk_completed,itlb.itlb_flush
7,720,030,970 dtlb_load_misses_walk_duration [57.13%]
169,856,353 dtlb_load_misses_walk_completed [57.15%]
708,832,859 dtlb_store_misses_walk_duration [57.17%]
19,346,823 dtlb_store_misses_walk_completed [57.17%]
2,779,687,402 itlb_misses_walk_duration [57.15%]
82,241,148 itlb_misses_walk_completed [57.13%]
770,717 itlb_itlb_flush [57.11%]
Show that a dtlb miss is 17.1ns (~45 cycles) and a itlb miss is 13.0ns
(~34 cycles). At those rates, refilling the 512-entry dTLB takes
22,000 cycles. On a SandyBridge system with more cores and larger
caches, those are dtlb=13.4ns and itlb=9.5ns.
cat perf.stat.txt | perl -pe 's/,//g'
| awk '/itlb_misses_walk_duration/ { icyc+=$1 }
/itlb_misses_walk_completed/ { imiss+=$1 }
/dtlb_.*_walk_duration/ { dcyc+=$1 }
/dtlb_.*.*completed/ { dmiss+=$1 }
END {print "itlb cyc/miss: ", icyc/imiss, " dtlb cyc/miss: ", dcyc/dmiss, " ----- ", icyc,imiss, dcyc,dmiss }
On Westmere CPUs, the counters to use are: itlb_flush,itlb_misses.walk_cycles,itlb_misses.any,dtlb_misses.walk_cycles,dtlb_misses.any
The assumptions that this code went in under:
https://lkml.org/lkml/2012/6/12/119 say that a flush and a refill are
about 100ns. Being generous, that is over by a factor of 6 on the
refill side, although it is fairly close on the cost of an invlpg.
An increase of a single invlpg operation seems to lengthen the flush
range operation by about 200 cycles. Here is one example of the data
collected for flushing 10 and 11 pages (full data are below):
10: 0.43% 93.90% avg cycles: 3570 cycles/page: 357 samples: 4714
11: 0.20% 94.10% avg cycles: 3767 cycles/page: 342 samples: 2145
How to generate this table:
echo 10000 > /sys/kernel/debug/tracing/buffer_size_kb
echo x86-tsc > /sys/kernel/debug/tracing/trace_clock
echo 'reason != 0' > /sys/kernel/debug/tracing/events/tlb/tlb_flush/filter
echo 1 > /sys/kernel/debug/tracing/events/tlb/tlb_flush/enable
Pipe the trace output in to this script:
http://sr71.net/~dave/intel/201402-tlb/trace-time-diff-process.pl.txt
Note that these data were gathered with the invlpg threshold set to
150 pages. Only data points with >=50 of samples were printed:
Flush % of %<=
in flush this
pages es size
------------------------------------------------------------------------------
-1: 2.20% 2.20% avg cycles: 2283 cycles/page: xxxx samples: 23960
1: 56.92% 59.12% avg cycles: 1276 cycles/page: 1276 samples: 620895
2: 13.78% 72.90% avg cycles: 1505 cycles/page: 752 samples: 150335
3: 8.26% 81.16% avg cycles: 1880 cycles/page: 626 samples: 90131
4: 7.41% 88.58% avg cycles: 2447 cycles/page: 611 samples: 80877
5: 1.73% 90.31% avg cycles: 2358 cycles/page: 471 samples: 18885
6: 1.32% 91.63% avg cycles: 2563 cycles/page: 427 samples: 14397
7: 1.14% 92.77% avg cycles: 2862 cycles/page: 408 samples: 12441
8: 0.62% 93.39% avg cycles: 3542 cycles/page: 442 samples: 6721
9: 0.08% 93.47% avg cycles: 3289 cycles/page: 365 samples: 917
10: 0.43% 93.90% avg cycles: 3570 cycles/page: 357 samples: 4714
11: 0.20% 94.10% avg cycles: 3767 cycles/page: 342 samples: 2145
12: 0.08% 94.18% avg cycles: 3996 cycles/page: 333 samples: 864
13: 0.03% 94.20% avg cycles: 4077 cycles/page: 313 samples: 289
14: 0.02% 94.23% avg cycles: 4836 cycles/page: 345 samples: 236
15: 0.04% 94.26% avg cycles: 5699 cycles/page: 379 samples: 390
16: 0.06% 94.32% avg cycles: 5041 cycles/page: 315 samples: 643
17: 0.57% 94.89% avg cycles: 5473 cycles/page: 321 samples: 6229
18: 0.02% 94.91% avg cycles: 5396 cycles/page: 299 samples: 224
19: 0.03% 94.95% avg cycles: 5296 cycles/page: 278 samples: 367
20: 0.02% 94.96% avg cycles: 6749 cycles/page: 337 samples: 185
21: 0.18% 95.14% avg cycles: 6225 cycles/page: 296 samples: 1964
22: 0.01% 95.15% avg cycles: 6393 cycles/page: 290 samples: 83
23: 0.01% 95.16% avg cycles: 6861 cycles/page: 298 samples: 61
24: 0.12% 95.28% avg cycles: 6912 cycles/page: 288 samples: 1307
25: 0.05% 95.32% avg cycles: 7190 cycles/page: 287 samples: 533
26: 0.01% 95.33% avg cycles: 7793 cycles/page: 299 samples: 94
27: 0.01% 95.34% avg cycles: 7833 cycles/page: 290 samples: 66
28: 0.01% 95.35% avg cycles: 8253 cycles/page: 294 samples: 73
29: 0.08% 95.42% avg cycles: 8024 cycles/page: 276 samples: 846
30: 0.03% 95.45% avg cycles: 9670 cycles/page: 322 samples: 296
31: 0.01% 95.46% avg cycles: 8949 cycles/page: 288 samples: 79
32: 0.01% 95.46% avg cycles: 9350 cycles/page: 292 samples: 60
33: 3.11% 98.57% avg cycles: 8534 cycles/page: 258 samples: 33936
34: 0.02% 98.60% avg cycles: 10977 cycles/page: 322 samples: 268
35: 0.02% 98.62% avg cycles: 11400 cycles/page: 325 samples: 177
36: 0.01% 98.63% avg cycles: 11504 cycles/page: 319 samples: 161
37: 0.02% 98.65% avg cycles: 11596 cycles/page: 313 samples: 182
38: 0.02% 98.66% avg cycles: 11850 cycles/page: 311 samples: 195
39: 0.01% 98.68% avg cycles: 12158 cycles/page: 311 samples: 128
40: 0.01% 98.68% avg cycles: 11626 cycles/page: 290 samples: 78
41: 0.04% 98.73% avg cycles: 11435 cycles/page: 278 samples: 477
42: 0.01% 98.73% avg cycles: 12571 cycles/page: 299 samples: 74
43: 0.01% 98.74% avg cycles: 12562 cycles/page: 292 samples: 78
44: 0.01% 98.75% avg cycles: 12991 cycles/page: 295 samples: 108
45: 0.01% 98.76% avg cycles: 13169 cycles/page: 292 samples: 78
46: 0.02% 98.78% avg cycles: 12891 cycles/page: 280 samples: 261
47: 0.01% 98.79% avg cycles: 13099 cycles/page: 278 samples: 67
48: 0.01% 98.80% avg cycles: 13851 cycles/page: 288 samples: 77
49: 0.01% 98.80% avg cycles: 13749 cycles/page: 280 samples: 66
50: 0.01% 98.81% avg cycles: 13949 cycles/page: 278 samples: 73
52: 0.00% 98.82% avg cycles: 14243 cycles/page: 273 samples: 52
54: 0.01% 98.83% avg cycles: 15312 cycles/page: 283 samples: 87
55: 0.01% 98.84% avg cycles: 15197 cycles/page: 276 samples: 109
56: 0.02% 98.86% avg cycles: 15234 cycles/page: 272 samples: 208
57: 0.00% 98.86% avg cycles: 14888 cycles/page: 261 samples: 53
58: 0.01% 98.87% avg cycles: 15037 cycles/page: 259 samples: 59
59: 0.01% 98.87% avg cycles: 15752 cycles/page: 266 samples: 63
62: 0.00% 98.89% avg cycles: 16222 cycles/page: 261 samples: 54
64: 0.02% 98.91% avg cycles: 17179 cycles/page: 268 samples: 248
65: 0.12% 99.03% avg cycles: 18762 cycles/page: 288 samples: 1324
85: 0.00% 99.10% avg cycles: 21649 cycles/page: 254 samples: 50
127: 0.01% 99.18% avg cycles: 32397 cycles/page: 255 samples: 75
128: 0.13% 99.31% avg cycles: 31711 cycles/page: 247 samples: 1466
129: 0.18% 99.49% avg cycles: 33017 cycles/page: 255 samples: 1927
181: 0.33% 99.84% avg cycles: 2489 cycles/page: 13 samples: 3547
256: 0.05% 99.91% avg cycles: 2305 cycles/page: 9 samples: 550
512: 0.03% 99.95% avg cycles: 2133 cycles/page: 4 samples: 304
1512: 0.01% 99.99% avg cycles: 3038 cycles/page: 2 samples: 65
Here are the tlb counters during a 10-second slice of a kernel compile
for a SandyBridge system. It's better than IvyBridge, but probably
due to the larger caches since this was one of the 'X' extreme parts.
10,873,007,282 dtlb_load_misses_walk_duration
250,711,333 dtlb_load_misses_walk_completed
1,212,395,865 dtlb_store_misses_walk_duration
31,615,772 dtlb_store_misses_walk_completed
5,091,010,274 itlb_misses_walk_duration
163,193,511 itlb_misses_walk_completed
1,321,980 itlb_itlb_flush
10.008045158 seconds time elapsed
# cat perf.stat.1392743721.txt | perl -pe 's/,//g' | awk '/itlb_misses_walk_duration/ { icyc+=$1 } /itlb_misses_walk_completed/ { imiss+=$1 } /dtlb_.*_walk_duration/ { dcyc+=$1 } /dtlb_.*.*completed/ { dmiss+=$1 } END {print "itlb cyc/miss: ", icyc/imiss/3.3, " dtlb cyc/miss: ", dcyc/dmiss/3.3, " ----- ", icyc,imiss, dcyc,dmiss }'
itlb ns/miss: 9.45338 dtlb ns/miss: 12.9716
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: http://lkml.kernel.org/r/20140731154103.10C1115E@viggo.jf.intel.com
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
||
|---|---|---|
| arch | ||
| block | ||
| crypto | ||
| Documentation | ||
| drivers | ||
| firmware | ||
| fs | ||
| include | ||
| init | ||
| ipc | ||
| kernel | ||
| lib | ||
| mm | ||
| net | ||
| samples | ||
| scripts | ||
| security | ||
| sound | ||
| tools | ||
| usr | ||
| virt/kvm | ||
| .gitignore | ||
| .mailmap | ||
| COPYING | ||
| CREDITS | ||
| Kbuild | ||
| Kconfig | ||
| MAINTAINERS | ||
| Makefile | ||
| README | ||
| REPORTING-BUGS | ||
Linux kernel release 3.x <http://kernel.org/>
These are the release notes for Linux version 3. Read them carefully,
as they tell you what this is all about, explain how to install the
kernel, and what to do if something goes wrong.
WHAT IS LINUX?
Linux is a clone of the operating system Unix, written from scratch by
Linus Torvalds with assistance from a loosely-knit team of hackers across
the Net. It aims towards POSIX and Single UNIX Specification compliance.
It has all the features you would expect in a modern fully-fledged Unix,
including true multitasking, virtual memory, shared libraries, demand
loading, shared copy-on-write executables, proper memory management,
and multistack networking including IPv4 and IPv6.
It is distributed under the GNU General Public License - see the
accompanying COPYING file for more details.
ON WHAT HARDWARE DOES IT RUN?
Although originally developed first for 32-bit x86-based PCs (386 or higher),
today Linux also runs on (at least) the Compaq Alpha AXP, Sun SPARC and
UltraSPARC, Motorola 68000, PowerPC, PowerPC64, ARM, Hitachi SuperH, Cell,
IBM S/390, MIPS, HP PA-RISC, Intel IA-64, DEC VAX, AMD x86-64, AXIS CRIS,
Xtensa, Tilera TILE, AVR32 and Renesas M32R architectures.
Linux is easily portable to most general-purpose 32- or 64-bit architectures
as long as they have a paged memory management unit (PMMU) and a port of the
GNU C compiler (gcc) (part of The GNU Compiler Collection, GCC). Linux has
also been ported to a number of architectures without a PMMU, although
functionality is then obviously somewhat limited.
Linux has also been ported to itself. You can now run the kernel as a
userspace application - this is called UserMode Linux (UML).
DOCUMENTATION:
- There is a lot of documentation available both in electronic form on
the Internet and in books, both Linux-specific and pertaining to
general UNIX questions. I'd recommend looking into the documentation
subdirectories on any Linux FTP site for the LDP (Linux Documentation
Project) books. This README is not meant to be documentation on the
system: there are much better sources available.
- There are various README files in the Documentation/ subdirectory:
these typically contain kernel-specific installation notes for some
drivers for example. See Documentation/00-INDEX for a list of what
is contained in each file. Please read the Changes file, as it
contains information about the problems, which may result by upgrading
your kernel.
- The Documentation/DocBook/ subdirectory contains several guides for
kernel developers and users. These guides can be rendered in a
number of formats: PostScript (.ps), PDF, HTML, & man-pages, among others.
After installation, "make psdocs", "make pdfdocs", "make htmldocs",
or "make mandocs" will render the documentation in the requested format.
INSTALLING the kernel source:
- If you install the full sources, put the kernel tarball in a
directory where you have permissions (eg. your home directory) and
unpack it:
gzip -cd linux-3.X.tar.gz | tar xvf -
or
bzip2 -dc linux-3.X.tar.bz2 | tar xvf -
Replace "X" with the version number of the latest kernel.
Do NOT use the /usr/src/linux area! This area has a (usually
incomplete) set of kernel headers that are used by the library header
files. They should match the library, and not get messed up by
whatever the kernel-du-jour happens to be.
- You can also upgrade between 3.x releases by patching. Patches are
distributed in the traditional gzip and the newer bzip2 format. To
install by patching, get all the newer patch files, enter the
top level directory of the kernel source (linux-3.X) and execute:
gzip -cd ../patch-3.x.gz | patch -p1
or
bzip2 -dc ../patch-3.x.bz2 | patch -p1
Replace "x" for all versions bigger than the version "X" of your current
source tree, _in_order_, and you should be ok. You may want to remove
the backup files (some-file-name~ or some-file-name.orig), and make sure
that there are no failed patches (some-file-name# or some-file-name.rej).
If there are, either you or I have made a mistake.
Unlike patches for the 3.x kernels, patches for the 3.x.y kernels
(also known as the -stable kernels) are not incremental but instead apply
directly to the base 3.x kernel. For example, if your base kernel is 3.0
and you want to apply the 3.0.3 patch, you must not first apply the 3.0.1
and 3.0.2 patches. Similarly, if you are running kernel version 3.0.2 and
want to jump to 3.0.3, you must first reverse the 3.0.2 patch (that is,
patch -R) _before_ applying the 3.0.3 patch. You can read more on this in
Documentation/applying-patches.txt
Alternatively, the script patch-kernel can be used to automate this
process. It determines the current kernel version and applies any
patches found.
linux/scripts/patch-kernel linux
The first argument in the command above is the location of the
kernel source. Patches are applied from the current directory, but
an alternative directory can be specified as the second argument.
- Make sure you have no stale .o files and dependencies lying around:
cd linux
make mrproper
You should now have the sources correctly installed.
SOFTWARE REQUIREMENTS
Compiling and running the 3.x kernels requires up-to-date
versions of various software packages. Consult
Documentation/Changes for the minimum version numbers required
and how to get updates for these packages. Beware that using
excessively old versions of these packages can cause indirect
errors that are very difficult to track down, so don't assume that
you can just update packages when obvious problems arise during
build or operation.
BUILD directory for the kernel:
When compiling the kernel, all output files will per default be
stored together with the kernel source code.
Using the option "make O=output/dir" allow you to specify an alternate
place for the output files (including .config).
Example:
kernel source code: /usr/src/linux-3.X
build directory: /home/name/build/kernel
To configure and build the kernel, use:
cd /usr/src/linux-3.X
make O=/home/name/build/kernel menuconfig
make O=/home/name/build/kernel
sudo make O=/home/name/build/kernel modules_install install
Please note: If the 'O=output/dir' option is used, then it must be
used for all invocations of make.
CONFIGURING the kernel:
Do not skip this step even if you are only upgrading one minor
version. New configuration options are added in each release, and
odd problems will turn up if the configuration files are not set up
as expected. If you want to carry your existing configuration to a
new version with minimal work, use "make oldconfig", which will
only ask you for the answers to new questions.
- Alternative configuration commands are:
"make config" Plain text interface.
"make menuconfig" Text based color menus, radiolists & dialogs.
"make nconfig" Enhanced text based color menus.
"make xconfig" X windows (Qt) based configuration tool.
"make gconfig" X windows (Gtk) based configuration tool.
"make oldconfig" Default all questions based on the contents of
your existing ./.config file and asking about
new config symbols.
"make silentoldconfig"
Like above, but avoids cluttering the screen
with questions already answered.
Additionally updates the dependencies.
"make olddefconfig"
Like above, but sets new symbols to their default
values without prompting.
"make defconfig" Create a ./.config file by using the default
symbol values from either arch/$ARCH/defconfig
or arch/$ARCH/configs/${PLATFORM}_defconfig,
depending on the architecture.
"make ${PLATFORM}_defconfig"
Create a ./.config file by using the default
symbol values from
arch/$ARCH/configs/${PLATFORM}_defconfig.
Use "make help" to get a list of all available
platforms of your architecture.
"make allyesconfig"
Create a ./.config file by setting symbol
values to 'y' as much as possible.
"make allmodconfig"
Create a ./.config file by setting symbol
values to 'm' as much as possible.
"make allnoconfig" Create a ./.config file by setting symbol
values to 'n' as much as possible.
"make randconfig" Create a ./.config file by setting symbol
values to random values.
"make localmodconfig" Create a config based on current config and
loaded modules (lsmod). Disables any module
option that is not needed for the loaded modules.
To create a localmodconfig for another machine,
store the lsmod of that machine into a file
and pass it in as a LSMOD parameter.
target$ lsmod > /tmp/mylsmod
target$ scp /tmp/mylsmod host:/tmp
host$ make LSMOD=/tmp/mylsmod localmodconfig
The above also works when cross compiling.
"make localyesconfig" Similar to localmodconfig, except it will convert
all module options to built in (=y) options.
You can find more information on using the Linux kernel config tools
in Documentation/kbuild/kconfig.txt.
- NOTES on "make config":
- Having unnecessary drivers will make the kernel bigger, and can
under some circumstances lead to problems: probing for a
nonexistent controller card may confuse your other controllers
- Compiling the kernel with "Processor type" set higher than 386
will result in a kernel that does NOT work on a 386. The
kernel will detect this on bootup, and give up.
- A kernel with math-emulation compiled in will still use the
coprocessor if one is present: the math emulation will just
never get used in that case. The kernel will be slightly larger,
but will work on different machines regardless of whether they
have a math coprocessor or not.
- The "kernel hacking" configuration details usually result in a
bigger or slower kernel (or both), and can even make the kernel
less stable by configuring some routines to actively try to
break bad code to find kernel problems (kmalloc()). Thus you
should probably answer 'n' to the questions for "development",
"experimental", or "debugging" features.
COMPILING the kernel:
- Make sure you have at least gcc 3.2 available.
For more information, refer to Documentation/Changes.
Please note that you can still run a.out user programs with this kernel.
- Do a "make" to create a compressed kernel image. It is also
possible to do "make install" if you have lilo installed to suit the
kernel makefiles, but you may want to check your particular lilo setup first.
To do the actual install, you have to be root, but none of the normal
build should require that. Don't take the name of root in vain.
- If you configured any of the parts of the kernel as `modules', you
will also have to do "make modules_install".
- Verbose kernel compile/build output:
Normally, the kernel build system runs in a fairly quiet mode (but not
totally silent). However, sometimes you or other kernel developers need
to see compile, link, or other commands exactly as they are executed.
For this, use "verbose" build mode. This is done by inserting
"V=1" in the "make" command. E.g.:
make V=1 all
To have the build system also tell the reason for the rebuild of each
target, use "V=2". The default is "V=0".
- Keep a backup kernel handy in case something goes wrong. This is
especially true for the development releases, since each new release
contains new code which has not been debugged. Make sure you keep a
backup of the modules corresponding to that kernel, as well. If you
are installing a new kernel with the same version number as your
working kernel, make a backup of your modules directory before you
do a "make modules_install".
Alternatively, before compiling, use the kernel config option
"LOCALVERSION" to append a unique suffix to the regular kernel version.
LOCALVERSION can be set in the "General Setup" menu.
- In order to boot your new kernel, you'll need to copy the kernel
image (e.g. .../linux/arch/i386/boot/bzImage after compilation)
to the place where your regular bootable kernel is found.
- Booting a kernel directly from a floppy without the assistance of a
bootloader such as LILO, is no longer supported.
If you boot Linux from the hard drive, chances are you use LILO, which
uses the kernel image as specified in the file /etc/lilo.conf. The
kernel image file is usually /vmlinuz, /boot/vmlinuz, /bzImage or
/boot/bzImage. To use the new kernel, save a copy of the old image
and copy the new image over the old one. Then, you MUST RERUN LILO
to update the loading map!! If you don't, you won't be able to boot
the new kernel image.
Reinstalling LILO is usually a matter of running /sbin/lilo.
You may wish to edit /etc/lilo.conf to specify an entry for your
old kernel image (say, /vmlinux.old) in case the new one does not
work. See the LILO docs for more information.
After reinstalling LILO, you should be all set. Shutdown the system,
reboot, and enjoy!
If you ever need to change the default root device, video mode,
ramdisk size, etc. in the kernel image, use the 'rdev' program (or
alternatively the LILO boot options when appropriate). No need to
recompile the kernel to change these parameters.
- Reboot with the new kernel and enjoy.
IF SOMETHING GOES WRONG:
- If you have problems that seem to be due to kernel bugs, please check
the file MAINTAINERS to see if there is a particular person associated
with the part of the kernel that you are having trouble with. If there
isn't anyone listed there, then the second best thing is to mail
them to me (torvalds@linux-foundation.org), and possibly to any other
relevant mailing-list or to the newsgroup.
- In all bug-reports, *please* tell what kernel you are talking about,
how to duplicate the problem, and what your setup is (use your common
sense). If the problem is new, tell me so, and if the problem is
old, please try to tell me when you first noticed it.
- If the bug results in a message like
unable to handle kernel paging request at address C0000010
Oops: 0002
EIP: 0010:XXXXXXXX
eax: xxxxxxxx ebx: xxxxxxxx ecx: xxxxxxxx edx: xxxxxxxx
esi: xxxxxxxx edi: xxxxxxxx ebp: xxxxxxxx
ds: xxxx es: xxxx fs: xxxx gs: xxxx
Pid: xx, process nr: xx
xx xx xx xx xx xx xx xx xx xx
or similar kernel debugging information on your screen or in your
system log, please duplicate it *exactly*. The dump may look
incomprehensible to you, but it does contain information that may
help debugging the problem. The text above the dump is also
important: it tells something about why the kernel dumped code (in
the above example, it's due to a bad kernel pointer). More information
on making sense of the dump is in Documentation/oops-tracing.txt
- If you compiled the kernel with CONFIG_KALLSYMS you can send the dump
as is, otherwise you will have to use the "ksymoops" program to make
sense of the dump (but compiling with CONFIG_KALLSYMS is usually preferred).
This utility can be downloaded from
ftp://ftp.<country>.kernel.org/pub/linux/utils/kernel/ksymoops/ .
Alternatively, you can do the dump lookup by hand:
- In debugging dumps like the above, it helps enormously if you can
look up what the EIP value means. The hex value as such doesn't help
me or anybody else very much: it will depend on your particular
kernel setup. What you should do is take the hex value from the EIP
line (ignore the "0010:"), and look it up in the kernel namelist to
see which kernel function contains the offending address.
To find out the kernel function name, you'll need to find the system
binary associated with the kernel that exhibited the symptom. This is
the file 'linux/vmlinux'. To extract the namelist and match it against
the EIP from the kernel crash, do:
nm vmlinux | sort | less
This will give you a list of kernel addresses sorted in ascending
order, from which it is simple to find the function that contains the
offending address. Note that the address given by the kernel
debugging messages will not necessarily match exactly with the
function addresses (in fact, that is very unlikely), so you can't
just 'grep' the list: the list will, however, give you the starting
point of each kernel function, so by looking for the function that
has a starting address lower than the one you are searching for but
is followed by a function with a higher address you will find the one
you want. In fact, it may be a good idea to include a bit of
"context" in your problem report, giving a few lines around the
interesting one.
If you for some reason cannot do the above (you have a pre-compiled
kernel image or similar), telling me as much about your setup as
possible will help. Please read the REPORTING-BUGS document for details.
- Alternatively, you can use gdb on a running kernel. (read-only; i.e. you
cannot change values or set break points.) To do this, first compile the
kernel with -g; edit arch/i386/Makefile appropriately, then do a "make
clean". You'll also need to enable CONFIG_PROC_FS (via "make config").
After you've rebooted with the new kernel, do "gdb vmlinux /proc/kcore".
You can now use all the usual gdb commands. The command to look up the
point where your system crashed is "l *0xXXXXXXXX". (Replace the XXXes
with the EIP value.)
gdb'ing a non-running kernel currently fails because gdb (wrongly)
disregards the starting offset for which the kernel is compiled.