linux/arch/arm/mach-omap2
Tony Lindgren a2fc36613a ARM: OMAP3: Use manual idle for UARTs because of DMA errata
In sprz318f.pdf "Usage Note 2.7" says that UARTs cannot acknowledge
idle requests in smartidle mode when configured for DMA operations.
This prevents L4 from going idle. So let's use manual idle mode
instead.

Otherwise systems using Sebastian's 8250 patches with DMA will
never enter deeper idle states because of the errata above.

Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2014-09-18 08:58:49 -07:00
..
include/mach ARM: drop <mach/timex.h> for !ARCH_MULTIPLATFORM, too 2013-12-20 17:17:16 +01:00
am33xx-restart.c ARM: OMAP2+: am33xx-restart: trigger warm reset on omap2+ boards 2013-08-21 01:01:30 -07:00
am33xx.h ARM: OMAP2+: AM43x: early init 2013-06-12 08:00:35 -07:00
am35xx-emac.c ARM: 7989/1: Delete asm/system.h 2014-02-25 11:33:37 +00:00
am35xx-emac.h
am35xx.h ARM: OMAP2+: Make am35xx.h local 2012-09-20 15:02:23 -07:00
board-3430sdp.c ARM: OMAP: 3430SDP: use new display drivers 2013-08-28 10:23:21 +03:00
board-am3517crane.c ARM: OMAP2: remove useless variable 'ret' 2013-08-22 00:15:17 -07:00
board-am3517evm.c ARM: OMAP: AM3517EVM: remove check for CONFIG_PANEL_SHARP_LQ043T1DG01 2014-05-16 14:13:07 -07:00
board-cm-t35.c [media] ARM: omap2: cm-t35: Add regulators and clock for camera sensor 2014-02-24 13:10:14 -03:00
board-cm-t3517.c Clean-up for omap2+ timers from Jon Hunter <jon-hunter@ti.com>: 2013-04-08 19:30:48 +02:00
board-devkit8000.c ARM: OMAP: devkit8000: use new display drivers 2013-08-28 10:23:20 +03:00
board-flash.c mtd: nand: omap: Revert to using software ECC by default 2014-08-25 16:15:32 -07:00
board-flash.h ARM: OMAP2+: gpmc: localize gpmc header 2012-10-15 14:42:15 +05:30
board-generic.c ARM: OMAP2+: Add machine entry for dra72x devices 2014-05-06 10:20:14 -07:00
board-ldp.c ARM: OMAP2+: Fix LCD panel backlight regression for LDP legacy booting 2013-12-27 09:33:27 -08:00
board-n8x0.c ARM: OMAP2+: dts: add n8x0 onenand 2013-11-25 15:38:09 -08:00
board-omap3beagle.c pwm: Changes for v3.16-rc1 2014-06-11 14:06:55 -07:00
board-omap3logic.c arm-soc: cleanups 2013-02-21 14:58:40 -08:00
board-omap3pandora.c wl1251: move power GPIO handling into the driver 2014-02-28 14:08:26 -05:00
board-omap3stalker.c ARM: OMAP: omap3stalker: remove two Kconfig macros 2014-05-16 14:10:04 -07:00
board-omap3touchbook.c arch/arm/mach-omap2: replace strict_strto* with kstrto* 2014-08-08 15:57:27 -07:00
board-overo.c ARM: OMAP: overo: use new display drivers 2013-08-28 10:23:19 +03:00
board-rx51-peripherals.c wl1251: move power GPIO handling into the driver 2014-02-28 14:08:26 -05:00
board-rx51-video.c ARM: OMAP2+: N900: remove omapdss init for DT boot 2014-04-18 16:37:43 -07:00
board-rx51.c ARM: OMAP3: RX-51: ARM errata 430973 workaround 2013-10-08 11:57:04 -07:00
board-rx51.h ARM: OMAP2+: Make board-rx51.h local 2012-09-20 15:02:27 -07:00
board-ti8168evm.c ARM: delete struct sys_timer 2012-12-24 09:36:38 -07:00
cclock3xxx_data.c ARM: OMAP3: clock: Back-propagate rate change from cam_mclk to dpll4_m5 on all OMAP3 platforms 2014-04-28 15:58:22 -06:00
clkt2xxx_apll.c ARM: OMAP2: CM/PM: remove direct register accesses outside CM code 2013-10-19 10:11:51 -06:00
clkt2xxx_dpll.c ARM: OMAP2: clock: Cleanup !CONFIG_COMMON_CLK parts 2012-11-12 19:18:51 -07:00
clkt2xxx_dpllcore.c ARM: OMAP2+: raw read and write endian fix 2014-05-08 07:09:53 -07:00
clkt2xxx_virt_prcm_set.c ARM: OMAP2: clock: add DT boot support for cpufreq_ck 2014-05-28 13:05:57 +03:00
clkt34xx_dpll3m2.c omap prcm changes via Paul Walmsley <paul@pwsan.com>: 2012-11-30 08:40:31 -08:00
clkt_clksel.c ARM: OMAP2+: clock: use driver API instead of direct memory read/write 2014-01-17 12:37:00 -08:00
clkt_dpll.c Few fixes for the v3.17 merge window: 2014-08-09 08:23:27 -07:00
clkt_iclk.c ARM: OMAP2+: clock/interface: remove some headers from clkt_iclk.c file 2014-07-15 14:09:24 -06:00
clock2xxx.c ARM: OMAP2+: Use omap initcalls 2013-01-11 11:24:18 -08:00
clock2xxx.h ARM: OMAP2: convert sys_ck and osc_ck to standard clock types 2014-07-02 14:26:06 +03:00
clock3xxx.c ARM: OMAP2+: Use omap initcalls 2013-01-11 11:24:18 -08:00
clock3xxx.h CLK: TI: add omap3 clock init file 2014-01-17 12:35:48 -08:00
clock34xx.c ARM: OMAP3: clock: Cleanup !CONFIG_COMMON_CLK parts 2012-11-12 19:18:50 -07:00
clock34xx.h
clock36xx.c ARM: OMAP2+: clock: use driver API instead of direct memory read/write 2014-01-17 12:37:00 -08:00
clock36xx.h ARM: OMAP3: clock: Cleanup !CONFIG_COMMON_CLK parts 2012-11-12 19:18:50 -07:00
clock44xx.h
clock2430.c ARM: OMAP2: clock: Cleanup !CONFIG_COMMON_CLK parts 2012-11-12 19:18:51 -07:00
clock3517.c ARM: OMAP3: clock: Cleanup !CONFIG_COMMON_CLK parts 2012-11-12 19:18:50 -07:00
clock3517.h
clock_common_data.c ARM: OMAP2+: clock: Cleanup !CONFIG_COMMON_CLK parts 2012-11-12 19:18:51 -07:00
clock.c ARM: SoC device-tree changes for 3.17 2014-08-08 11:16:58 -07:00
clock.h ARM: SoC device-tree changes for 3.17 2014-08-08 11:16:58 -07:00
clockdomain.c ARM: OMAP2+: clockdomain: convert existing atomic usecounts into spinlock-protected shorts/ints 2013-01-29 14:59:58 -07:00
clockdomain.h ARM: OMAP2+: PRCM: cleanup some header includes 2014-05-15 22:34:48 -06:00
clockdomains2xxx_3xxx_data.c
clockdomains3xxx_data.c ARM: OMAP3: fix iva mmu programming issues 2014-03-12 09:48:26 -07:00
clockdomains7xx_data.c ARM: OMAP: DRA7: clockdomain: Add DRA7XX data and update header 2013-08-23 04:28:36 -06:00
clockdomains33xx_data.c
clockdomains43xx_data.c ARM: OMAP2+: CM: AM43x clockdomain data 2013-10-13 22:48:36 -06:00
clockdomains44xx_data.c ARM: OMAP2+: clockdomain: Fix OMAP4 ISS clk domain to support only SWSUP 2012-10-29 22:02:13 -06:00
clockdomains54xx_data.c ARM: OMAP5: clockdomain data: Add OMAP54XX data and update the header 2013-06-08 11:56:15 -06:00
clockdomains2420_data.c ARM: OMAP: Split plat/cpu.h into local soc.h for mach-omap1 and mach-omap2 2012-10-18 16:23:46 -07:00
clockdomains2430_data.c ARM: OMAP: Split plat/cpu.h into local soc.h for mach-omap1 and mach-omap2 2012-10-18 16:23:46 -07:00
cm1_7xx.h ARM: OMAP: DRA7: CM: Add DRA7XX register defines 2013-08-23 04:24:15 -06:00
cm1_44xx.h ARM: OMAP4+: CM: Move function prototypes to common header for re-use 2013-06-08 11:41:39 -06:00
cm1_54xx.h ARM: OMAP5: CM: Add OMAP54XX register and bitfield files 2013-06-08 11:46:09 -06:00
cm2_7xx.h arm: dra7xx: Add hwmod data for pcie1 phy and pcie2 phy 2014-07-22 14:35:05 -06:00
cm2_44xx.h ARM: OMAP4+: CM: Move function prototypes to common header for re-use 2013-06-08 11:41:39 -06:00
cm2_54xx.h ARM: OMAP5: CM: Add OMAP54XX register and bitfield files 2013-06-08 11:46:09 -06:00
cm2xxx_3xxx.h ARM: OMAP2+: raw read and write endian fix 2014-05-08 07:09:53 -07:00
cm2xxx.c ARM: OMAP2/3: CM: remove some external dependencies 2014-05-15 22:34:25 -06:00
cm2xxx.h ARM: OMAP2: CM/PM: remove direct register accesses outside CM code 2013-10-19 10:11:51 -06:00
cm3xxx.c ARM: OMAP2/3: CM: remove some external dependencies 2014-05-15 22:34:25 -06:00
cm3xxx.h ARM: OMAP3: CM: remove a few OMAP34XX_CM_REGADDR defines 2014-05-11 19:35:13 -06:00
cm33xx.c ARM: OMAP2+: raw read and write endian fix 2014-05-08 07:09:53 -07:00
cm33xx.h ARM: OMAP2+: hwmod: Change hardreset soc_ops for AM43XX 2014-06-15 16:02:17 -06:00
cm44xx.c Some OMAP PRCM cleanup patches. These help prepare to convert the PRCM 2014-05-16 15:26:22 -07:00
cm44xx.h
cm_44xx_54xx.h ARM: OMAP4+: CM: Move function prototypes to common header for re-use 2013-06-08 11:41:39 -06:00
cm_common.c ARM: OMAP2+: PRCM: cleanup some header includes 2014-05-15 22:34:48 -06:00
cm-regbits-7xx.h ARM: OMAP: DRA7: CM: Add minimal regbit shifts 2013-08-23 04:28:36 -06:00
cm-regbits-24xx.h ARM: OMAP2: convert sys_ck and osc_ck to standard clock types 2014-07-02 14:26:06 +03:00
cm-regbits-33xx.h ARM: OMAP3: PRM/CM: Cleanup unused header 2013-07-21 22:10:03 -06:00
cm-regbits-34xx.h ARM: OMAP3: PRM/CM: Add back macros used by TI DSP/Bridge driver 2014-07-06 15:51:23 -06:00
cm-regbits-44xx.h ARM: OMAP4: PRM/CM: Cleanup unused header 2013-07-21 22:10:14 -06:00
cm-regbits-54xx.h ARM: OMAP5: PRM/CM: Cleanup unused header 2013-07-21 22:10:25 -06:00
cm.h ARM: OMAP2+: PRCM: split and relocate the PRM/CM globals setup 2012-11-08 15:09:26 -07:00
cminst44xx.c Some OMAP PRCM cleanup patches. These help prepare to convert the PRCM 2014-05-16 15:26:22 -07:00
cminst44xx.h ARM: OMAP2+: CM: cm_inst offset s16->u16 2013-10-13 22:46:38 -06:00
common-board-devices.c ARM: arm-soc: Header cleanups 2012-12-12 11:45:16 -08:00
common-board-devices.h ARM: OMAP2+: Add quirks support for n8x0 2013-11-25 15:31:17 -08:00
common.c ARM: OMAP2+: remove DSP platform device 2014-07-15 21:01:05 -07:00
common.h ARM: DRA7: Add hook in SoC initcalls to enable pm initialization 2014-09-08 15:50:39 -07:00
control.c ARM: OMAP3: Fix coding style problems in arch/arm/mach-omap2/control.c 2014-08-01 01:21:14 -07:00
control.h Merge branch 'for-v3.17/cm-prm-cleanup' of https://github.com/t-kristo/linux-pm into omap-for-v3.17/soc 2014-07-15 07:00:00 -07:00
cpuidle34xx.c ARM: arm-soc cleanup for 3.10 2013-05-02 09:03:55 -07:00
cpuidle44xx.c ARM: OMAP4: Fix the boot regression with CPU_IDLE enabled 2014-05-19 11:20:38 -07:00
ctrl_module_wkup_44xx.h ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local 2012-09-20 15:02:33 -07:00
devices.c SoC related changes for omaps for v3.17 merge window: 2014-07-26 11:33:34 +02:00
devices.h
display.c OMAPDSS: move 'compatible' converter to omapdss driver 2014-05-28 09:25:15 +03:00
display.h ARM: OMAP2+: add omapdss_init_of() 2014-03-19 10:52:23 +02:00
dma.c ARM: OMAP2+: DMA: remove requirement of irq for platform-dma driver 2014-07-21 23:32:51 -07:00
dpll3xxx.c Modify OMAP PLL rate rounding function to round to the exact rate requested 2014-07-29 04:03:30 -07:00
dpll44xx.c ARM: OMAP4+: dpll44xx: remove cm-regbits-44xx.h and clock44xx.h includes 2014-07-15 14:08:49 -06:00
drm.c ARM: OMAP2+: display: Create omapdrm device inside omap_display_init 2013-10-08 14:02:35 -07:00
dss-common.c ARM: OMAP2+: remove pdata quirks for displays 2014-04-04 09:55:18 +03:00
dss-common.h ARM: OMAP2+: pdata-quirks: add legacy display init for IGEPv2 board 2013-10-09 07:54:34 -07:00
emu.c ARM: OMAP2+: Use omap initcalls 2013-01-11 11:24:18 -08:00
fb.c ARM: OMAP2+: display: Create omapvrfb and omapfb devices inside omap_display_init 2013-10-08 14:02:51 -07:00
gpio.c arm-soc: soc-specific updates 2013-02-21 15:27:22 -08:00
gpmc-nand.c mtd: nand: omap: Revert to using software ECC by default 2014-08-25 16:15:32 -07:00
gpmc-nand.h ARM: OMAP2+: gpmc: localize gpmc header 2012-10-15 14:42:15 +05:30
gpmc-onenand.c ARM: OMAP2: gpmc-onenand: fix sync mode setup with DT 2013-10-03 10:59:50 -07:00
gpmc-onenand.h ARM: OMAP2+: onenand: header cleanup 2012-10-15 14:42:03 +05:30
gpmc-smc91x.c ARM: OMAP2+: Convert SMC91x to use gpmc_cs_program_settings() 2013-04-01 14:53:43 -05:00
gpmc-smc91x.h ARM: OMAP2+: Make gpmc-smc91x.h local 2012-09-20 15:02:49 -07:00
gpmc-smsc911x.c ARM: OMAP2+: smsc911x: fix return value check in gpmc_smsc911x_init() 2013-11-14 10:40:36 -08:00
gpmc-smsc911x.h ARM: OMAP2+: Make gpmc-smsc911x.h local 2012-09-20 15:03:55 -07:00
gpmc.c ARM: OMAP2+: GPMC: Support Software ECC scheme via DT 2014-08-25 16:15:33 -07:00
gpmc.h ARM: OMAP2+: Add function to read GPMC settings from device-tree 2013-04-01 14:53:45 -05:00
hdq1w.c ARM: omap2+: skip device build from platform code for dt 2014-05-14 14:41:25 -07:00
hdq1w.h ARM: OMAP: Make plat/omap_hwmod.h local to mach-omap2 2012-10-18 16:05:55 -07:00
hsmmc.c ARM: OMAP2+: Remove omap4 pdata from hsmmc.c 2013-05-30 13:09:31 -07:00
hsmmc.h
hwspinlock.c arm-soc: soc-specific updates 2013-02-21 15:27:22 -08:00
i2c.c PTR_RET is now PTR_ERR_OR_ZERO(): Replace most. 2013-07-15 11:25:01 +09:30
i2c.h ARM: OMAP: Fix relative includes for shared i2c.h file 2012-10-31 15:37:13 -07:00
id.c ARM: OMAP: fix %d confusingly prefixed with 0x in format string 2014-08-25 16:15:34 -07:00
id.h ARM: OMAP2+: Make id.h local 2012-09-20 15:02:22 -07:00
io.c ARM: DRA7: Add hook in SoC initcalls to enable pm initialization 2014-09-08 15:50:39 -07:00
iomap.h ARM: OMAP5: Add minimal support for OMAP5430 SOC 2012-07-09 19:14:39 +05:30
irq.c ARM: OMAP2+: raw read and write endian fix 2014-05-08 07:09:53 -07:00
Kconfig ARM: omap: Remove stray ARCH_HAS_OPP references 2014-09-08 17:20:10 -07:00
l3_2xxx.h ARM: OMAP2+: Make l3_2xxx.h local 2012-09-20 15:03:59 -07:00
l3_3xxx.h ARM: OMAP2+: Make l3_3xxx.h local 2012-09-20 15:04:00 -07:00
l4_2xxx.h ARM: OMAP2+: Make l4_2xxx.h local 2012-09-20 15:04:01 -07:00
l4_3xxx.h ARM: OMAP2+: Make l4_3xxx.h local 2012-09-20 15:04:03 -07:00
Makefile ARM: OMAP5+: Reuse OMAP4 PM code for OMAP5 and DRA7 2014-09-09 19:13:41 -07:00
Makefile.boot ARM: dtb: move all dtb targets to common Makefile 2012-09-20 22:58:17 -07:00
mcbsp.c ARM: OMAP3: McBSP: do not access CM register directly 2013-10-19 10:11:51 -06:00
mmc.h ARM: OMAP: Split plat/mmc.h into local headers and platform_data 2012-10-15 12:09:43 -07:00
msdi.c ARM: OMAP2+: Remove legacy booting support for n8x0 2013-11-25 15:31:17 -08:00
mux34xx.c ARM: OMAP2+: mux: fix trivial typo in name 2013-09-18 12:02:01 -07:00
mux34xx.h omap: mux: add AM/DM37x gpios 2013-05-08 17:07:40 -07:00
mux.c arch/arm/mach-omap2: replace strict_strto* with kstrto* 2014-08-08 15:57:27 -07:00
mux.h ARM: OMAP2+: remove OMAP_PACKAGE_ZAC and OMAP_PACKAGE_ZAF 2014-02-28 15:36:34 -08:00
omap2-restart.c reboot: arm: change reboot_mode to use enum reboot_mode 2013-07-09 10:33:29 -07:00
omap3-restart.c reboot: arm: change reboot_mode to use enum reboot_mode 2013-07-09 10:33:29 -07:00
omap4-common.c ARM: OMAP2+: l2c: squelch warning dump on power control setting 2014-07-14 09:24:43 -07:00
omap4-restart.c reboot: arm: change reboot_mode to use enum reboot_mode 2013-07-09 10:33:29 -07:00
omap4-sar-layout.h ARM: arm-soc cleanup for 3.10 2013-05-02 09:03:55 -07:00
omap24xx.h ARM: OMAP2+ Move SoC specific headers to be local to mach-omap2 2012-09-12 18:06:31 -07:00
omap34xx.h ARM: OMAP2+ Move SoC specific headers to be local to mach-omap2 2012-09-12 18:06:31 -07:00
omap44xx.h ARM: OMAP: Make use of available scu_a9_get_base() interface 2013-01-28 10:41:39 -07:00
omap54xx.h ARM: DRA7: Reuse io tables and add a new .init_early 2013-08-13 11:00:35 +05:30
omap_device.c ARM: OMAP2+: omap_device: remove warning that clk alias already exists 2014-08-25 16:15:34 -07:00
omap_device.h ARM: OMAP2+: omap_device: add fail hook for runtime_pm when bad data is detected 2013-12-10 09:39:52 -08:00
omap_hwmod_2xxx_3xxx_interconnect_data.c ARM: OMAP2: hwmod_data: Remove legacy mailbox data and addrs 2014-07-15 05:08:56 -07:00
omap_hwmod_2xxx_3xxx_ipblock_data.c ARM: AM43xx: hwmod: add DSS hwmod data 2014-07-05 17:44:57 -06:00
omap_hwmod_2xxx_interconnect_data.c ARM: OMAP2+: Remove legacy hwmod entries for omap2 2013-11-25 15:31:18 -08:00
omap_hwmod_2xxx_ipblock_data.c ARM: OMAP2+: hwmod_data: fix missing OMAP_INTC_START in irq data 2013-12-25 21:41:27 -07:00
omap_hwmod_3xxx_data.c ARM: OMAP3: Use manual idle for UARTs because of DMA errata 2014-09-18 08:58:49 -07:00
omap_hwmod_7xx_data.c ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists 2014-08-27 19:38:23 -06:00
omap_hwmod_33xx_43xx_common_data.h ARM: OMAP2+: hwmod: AM43x support 2013-10-13 22:48:46 -06:00
omap_hwmod_33xx_43xx_interconnect_data.c ARM: AM33xx: hwmod_data: Remove legacy mailbox addrs 2014-07-15 05:08:56 -07:00
omap_hwmod_33xx_43xx_ipblock_data.c ARM: OMAP2+: PRCM: cleanup some header includes 2014-05-15 22:34:48 -06:00
omap_hwmod_33xx_data.c ARM: OMAP2+: hwmod: AM335x: runtime register update 2013-10-13 22:47:56 -06:00
omap_hwmod_43xx_data.c ARM: AM43xx: hwmod: add DSS hwmod data 2014-07-05 17:44:57 -06:00
omap_hwmod_44xx_data.c ARM: SoC platform changes for 3.17 2014-08-08 11:14:29 -07:00
omap_hwmod_54xx_data.c ARM: OMAP5: hwmod: Add ocp2scp3 and sata hwmods 2014-06-15 20:12:52 -06:00
omap_hwmod_2420_data.c ARM: OMAP2: hwmod_data: Remove legacy mailbox data and addrs 2014-07-15 05:08:56 -07:00
omap_hwmod_2430_data.c ARM: OMAP2: hwmod_data: Remove legacy mailbox data and addrs 2014-07-15 05:08:56 -07:00
omap_hwmod_common_data.c ARM: OMAP: Make plat/omap_hwmod.h local to mach-omap2 2012-10-18 16:05:55 -07:00
omap_hwmod_common_data.h ARM: OMAP2: hwmod_data: Remove legacy mailbox data and addrs 2014-07-15 05:08:56 -07:00
omap_hwmod_common_ipblock_data.c ARM: AM43xx: hwmod: add DSS hwmod data 2014-07-05 17:44:57 -06:00
omap_hwmod_reset.c ARM: omap2: include linux/errno.h in hwmod_reset 2013-02-15 13:36:47 +01:00
omap_hwmod.c ARM: OMAP2+: Add hwmod flag for HWMOD_RECONFIG_IO_CHAIN 2014-09-18 08:58:28 -07:00
omap_hwmod.h ARM: OMAP2+: Add hwmod flag for HWMOD_RECONFIG_IO_CHAIN 2014-09-18 08:58:28 -07:00
omap_opp_data.h Merge branch 'omap-for-v3.8/pm' into omap-for-v3.8/clock 2012-11-13 13:25:38 -08:00
omap_phy_internal.c ARM: OMAP2+: raw read and write endian fix 2014-05-08 07:09:53 -07:00
omap_twl.c mfd: twl-core: Fix idle mode signaling for omaps when booted with device tree 2014-04-23 15:31:05 +01:00
omap-headsmp.S ARM: OMAP5: Redo THUMB mode switch on secondary CPU 2014-05-05 17:32:25 -07:00
omap-hotplug.c ARM: OMAP2+: raw read and write endian fix 2014-05-08 07:09:53 -07:00
omap-iommu.c ARM: omap: Don't set iommu pdata da_start and da_end fields 2014-07-29 12:39:23 +02:00
omap-mpuss-lowpower.c Merge branch 'pull/v3.18/for-omap-soc' of https://github.com/nmenon/linux-2.6-playground into omap-for-v3.18/soc 2014-09-08 15:20:15 -07:00
omap-pm-noop.c ARM: OMAP: Move omap-pm-noop.c local to mach-omap2 2012-10-31 15:37:13 -07:00
omap-pm.h PM / OPP: rename header to linux/pm_opp.h 2013-10-25 22:33:23 +02:00
omap-secure.c RX-51: Add support for OMAP3 ROM Random Number Generator 2013-10-08 12:02:12 -07:00
omap-secure.h ARM: OMAP5 / DRA7: PM / wakeupgen: Enables ES2 PM mode by default 2014-09-08 11:38:41 -05:00
omap-smc.S ARM: OMAP3: Add secure function omap_smc3() which calling instruction smc #1 2013-10-08 11:55:32 -07:00
omap-smp.c ARM: OMAP2+: raw read and write endian fix 2014-05-08 07:09:53 -07:00
omap-wakeupgen.c ARM: OMAP5 / DRA7: Enable CPU RET on suspend 2014-09-08 11:38:43 -05:00
omap-wakeupgen.h ARM: OMAP5 / DRA7: PM / wakeupgen: Enables ES2 PM mode by default 2014-09-08 11:38:41 -05:00
opp2xxx.h
opp3xxx_data.c ARM: OMAP2+: Use omap initcalls 2013-01-11 11:24:18 -08:00
opp4xxx_data.c ARM: OMAP2+: Use omap initcalls 2013-01-11 11:24:18 -08:00
opp2420_data.c ARM: OMAP: Split plat/hardware.h, use local soc.h for omap2+ 2012-09-12 18:06:31 -07:00
opp2430_data.c ARM: OMAP: Split plat/hardware.h, use local soc.h for omap2+ 2012-09-12 18:06:31 -07:00
opp.c ACPI and power management updates for 3.13-rc1 2013-11-14 13:41:48 +09:00
pdata-quirks.c ARM: AM437x: use pdata quirks for pinctrl information 2014-09-08 11:35:11 -05:00
pm24xx.c ARM: SoC device-tree changes for 3.17 2014-08-08 11:16:58 -07:00
pm34xx.c ARM: OMAP3: control: isolate control module init to its own function 2014-07-04 17:02:21 +03:00
pm44xx.c Merge branch 'pull/v3.18/for-omap-soc' of https://github.com/nmenon/linux-2.6-playground into omap-for-v3.18/soc 2014-09-08 15:20:15 -07:00
pm-debug.c Merge branch 'cleanup' into for-linus 2013-05-02 21:31:29 +01:00
pm.c PM related fixes for omap3 that were discovered during omap3 2014-05-26 13:24:56 -07:00
pm.h ARM: OMAP5 / DRA7: Enable CPU RET on suspend 2014-09-08 11:38:43 -05:00
pmu.c ARM: OMAP2+: Cocci spatch "ptr_ret.spatch" 2013-07-04 05:10:51 -07:00
powerdomain-common.c ARM: OMAP4: PRCM: remove references to cm-regbits-44xx.h from PRCM core files 2014-05-15 22:35:10 -06:00
powerdomain.c ARM: OMAP2+: powerdomain: introduce logic for finding valid power domain 2014-09-08 11:22:41 -05:00
powerdomain.h ARM: OMAP2+: powerdomain: introduce logic for finding valid power domain 2014-09-08 11:22:41 -05:00
powerdomains2xxx_3xxx_data.c ARM: OMAP2+: powerdomain: fix whitespace, improve flag comments 2013-01-29 14:59:58 -07:00
powerdomains2xxx_3xxx_data.h
powerdomains2xxx_data.c ARM: OMAP2+: powerdomain: fix whitespace, improve flag comments 2013-01-29 14:59:58 -07:00
powerdomains3xxx_data.c ARM: OMAP: TI81XX: add always-on powerdomain for TI81XX 2013-08-23 04:48:42 -06:00
powerdomains7xx_data.c ARM: OMAP: DRA7: powerdomain data: fix powerdomain powerstate 2014-09-08 11:22:31 -05:00
powerdomains33xx_data.c
powerdomains43xx_data.c ARM: OMAP2+: PM: AM43x powerdomain data 2013-10-13 22:48:25 -06:00
powerdomains44xx_data.c
powerdomains54xx_data.c ARM: OMAP5: powerdomain data: fix powerdomain powerstate 2014-09-08 11:22:40 -05:00
prcm43xx.h ARM: AM43xx: hwmod: add DSS hwmod data 2014-07-05 17:44:57 -06:00
prcm44xx.h ARM: OMAP: DRA7: PRCM: Add DRA7XX local MPU PRCM regsiters 2013-08-23 04:28:36 -06:00
prcm_mpu7xx.h ARM: OMAP: DRA7: PRCM: Add DRA7XX local MPU PRCM regsiters 2013-08-23 04:28:36 -06:00
prcm_mpu44xx.c ARM: OMAP2+: raw read and write endian fix 2014-05-08 07:09:53 -07:00
prcm_mpu44xx.h ARM: OMAP2+: PRCM: cleanup some header includes 2014-05-15 22:34:48 -06:00
prcm_mpu54xx.h ARM: OMAP5: PRCM: Add OMAP54XX local MPU PRCM registers 2013-06-08 11:55:18 -06:00
prcm_mpu_44xx_54xx.h ARM: OMAP4+: PRCM MPU: Move function prototypes to common header for re-use 2013-06-08 11:54:40 -06:00
prcm-common.h ARM: OMAP3/4: PRM: provide io chain reconfig function through irq setup 2014-05-15 22:34:54 -06:00
prm2xxx_3xxx.c ARM: OMAP2+: PRCM: cleanup some header includes 2014-05-15 22:34:48 -06:00
prm2xxx_3xxx.h ARM: OMAP2+: raw read and write endian fix 2014-05-08 07:09:53 -07:00
prm2xxx.c ARM: OMAP24xx: PRM: add API for clearing wakeup status bits 2014-07-04 17:02:16 +03:00
prm2xxx.h ARM: OMAP24xx: PRM: add API for clearing wakeup status bits 2014-07-04 17:02:16 +03:00
prm3xxx.c ARM: OMAP3+: PRM: register interrupt information from DT 2014-09-08 10:54:06 -05:00
prm3xxx.h ARM: OMAP3: PRM: move PRM init code from PM core to the driver 2014-07-04 17:02:17 +03:00
prm7xx.h arm: dra7xx: Add hwmod data for pcie1 phy and pcie2 phy 2014-07-22 14:35:05 -06:00
prm33xx.c Some OMAP PRCM cleanup patches. These help prepare to convert the PRCM 2014-05-16 15:26:22 -07:00
prm33xx.h ARM: OMAP2+: AM33XX: Update the hardreset API 2013-02-08 07:25:28 -07:00
prm44xx_54xx.h ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain 2013-11-18 11:03:37 -08:00
prm44xx.c ARM: OMAP4+: PRM: Enable wakeup capability for OMAP5, DRA7 2014-09-08 10:53:56 -05:00
prm44xx.h ARM: OMAP4+: PRM: Move function prototypes to common header for re-use 2013-06-08 11:02:20 -06:00
prm54xx.h ARM: OMAP5: PRM: Add OMAP54XX register and bitfield files 2013-06-08 11:41:01 -06:00
prm_common.c ARM: OMAP2: PRM: add support for OMAP2 specific clock providers 2014-07-02 15:06:35 +03:00
prm-regbits-24xx.h ARM: OMAP2: PRM/CM: Cleanup unused header 2013-07-21 21:13:59 -06:00
prm-regbits-33xx.h ARM: OMAP2+: Add back the define for AM33XX_RST_GLOBAL_WARM_SW_MASK 2013-08-29 19:10:59 -07:00
prm-regbits-34xx.h ARM: OMAP3: PRM/CM: Add back macros used by TI DSP/Bridge driver 2014-07-06 15:51:23 -06:00
prm-regbits-44xx.h ARM: OMAP4: PRM/CM: Cleanup unused header 2013-07-21 22:10:14 -06:00
prm.h ARM: OMAP3/4: PRM: add support of late_init call to prm_ll_ops 2014-05-15 22:35:04 -06:00
prminst44xx.c ARM: OMAP4+: prminst: provide function to find prm_dev instance offset 2014-09-08 10:53:25 -05:00
prminst44xx.h ARM: OMAP4+: prminst: provide function to find prm_dev instance offset 2014-09-08 10:53:25 -05:00
scrm44xx.h ARM: OMAP4: clock: Add 44xx data using common struct clk 2012-11-12 19:10:20 -07:00
scrm54xx.h ARM: OMAP5: SCRM: Add OMAP54XX header file. 2013-06-08 11:55:44 -06:00
sdram-hynix-h8mbx00u0mer-0em.h ARM: OMAP: move plat-omap/include/plat/sdrc.h into mach-omap2/sdrc.h 2012-10-17 10:18:37 -07:00
sdram-micron-mt46h32m32lf-6.h ARM: OMAP: move plat-omap/include/plat/sdrc.h into mach-omap2/sdrc.h 2012-10-17 10:18:37 -07:00
sdram-nokia.c ARM: OMAP: remove plat/clock.h 2012-10-18 16:23:20 -07:00
sdram-nokia.h
sdram-numonyx-m65kxxxxam.h ARM: OMAP: move plat-omap/include/plat/sdrc.h into mach-omap2/sdrc.h 2012-10-17 10:18:37 -07:00
sdram-qimonda-hyb18m512160af-6.h ARM: OMAP: move plat-omap/include/plat/sdrc.h into mach-omap2/sdrc.h 2012-10-17 10:18:37 -07:00
sdrc2xxx.c ARM: OMAP2+: raw read and write endian fix 2014-05-08 07:09:53 -07:00
sdrc.c omap prcm changes via Paul Walmsley <paul@pwsan.com>: 2012-11-30 08:40:31 -08:00
sdrc.h ARM: OMAP2+: raw read and write endian fix 2014-05-08 07:09:53 -07:00
serial.c ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with DEBUG_LL 2013-07-30 05:13:35 -06:00
serial.h ARM: OMAP2+: Fix relative includes for serial.h 2012-10-31 15:37:14 -07:00
sleep24xx.S ARM: OMAP2xxx: PM: enter WFI via inline asm if CORE stays active 2013-02-06 13:48:14 -07:00
sleep34xx.S omap prcm changes via Paul Walmsley <paul@pwsan.com>: 2012-11-30 08:40:31 -08:00
sleep44xx.S ARM: convert all "mov.* pc, reg" to "bx reg" for ARMv6+ 2014-07-18 12:29:04 +01:00
smartreflex-class3.c PM / AVS: SmartReflex: use omap_sr * for enable/disable interface 2013-06-10 10:46:18 -07:00
soc.h ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants 2014-08-27 19:38:22 -06:00
sr_device.c ARM: OMAP2+: raw read and write endian fix 2014-05-08 07:09:53 -07:00
sram34xx.S ARM: OMAP2+: CM/hwmod: split CM functions into OMAP2, OMAP3-specific files 2012-10-21 01:01:11 -06:00
sram242x.S ARM: convert all "mov.* pc, reg" to "bx reg" for ARMv6+ 2014-07-18 12:29:04 +01:00
sram243x.S ARM: convert all "mov.* pc, reg" to "bx reg" for ARMv6+ 2014-07-18 12:29:04 +01:00
sram.c ARM: OMAP2+: raw read and write endian fix 2014-05-08 07:09:53 -07:00
sram.h ARM: OMAP: Split sram.h to local headers and minimal shared header 2012-10-31 10:14:13 -07:00
ti81xx.h ARM: OMAP2+: common: remove mach-omap2/common.c globals and map_common_io code 2012-11-08 12:33:07 -07:00
timer.c ARM: SoC cleanups for 3.16 2014-06-02 16:14:07 -07:00
twl-common.c arm: omap3: twl: add phy consumer data in twl4030_usb_data 2013-09-27 17:36:58 -07:00
twl-common.h ARM: OMAP2+: twl-common: Allow boards to customize the twl4030 audio setup 2013-01-22 10:34:50 +01:00
usb-host.c usb: phy: rename <linux/usb/usb_phy_gen_xceiv.h> to <linux/usb/usb_phy_generic.h> 2014-04-21 14:07:24 -05:00
usb-musb.c ARM: OMAP2: fix musb usage for n8x0 2013-08-16 09:39:56 -07:00
usb-tusb6010.c ARM: omap2+: usb-tusb6010.c: Cleaning up variable is set more than once 2014-07-07 04:52:31 -07:00
usb.h ARM: OMAP2+: omap-usb-host: Get rid of platform_data from struct usbhs_phy_data 2013-10-04 09:29:10 -05:00
vc3xxx_data.c ARM: OMAP3+: voltage: introduce omap vc / vp params for voltagedomains 2012-11-05 15:08:22 -08:00
vc44xx_data.c ARM: OMAP3+: voltage: introduce omap vc / vp params for voltagedomains 2012-11-05 15:08:22 -08:00
vc.c ARM: SoC updates for 3.16 (part 1) 2014-06-02 16:15:12 -07:00
vc.h ARM: OMAP3: Fix idle mode signaling for sys_clkreq and sys_off_mode 2014-05-06 13:48:35 -07:00
voltage.c ARM: OMAP: unwrap strings 2012-09-12 02:57:10 -06:00
voltage.h Merge branch 'omap/pm-voltdomain-cleanup' into next/soc 2013-06-20 17:35:16 +02:00
voltagedomains2xxx_data.c
voltagedomains3xxx_data.c ARM: OMAP3+: voltage: introduce omap vc / vp params for voltagedomains 2012-11-05 15:08:22 -08:00
voltagedomains44xx_data.c Merge branch 'omap-for-v3.8/pm' into omap-for-v3.8/clock 2012-11-13 13:25:38 -08:00
voltagedomains54xx_data.c ARM: OMAP5: voltagedomain data: remove temporary OMAP4 voltage data 2013-06-25 17:11:06 -07:00
vp3xxx_data.c ARM: OMAP3+: voltage: introduce omap vc / vp params for voltagedomains 2012-11-05 15:08:22 -08:00
vp44xx_data.c ARM: OMAP3+: voltage: introduce omap vc / vp params for voltagedomains 2012-11-05 15:08:22 -08:00
vp.c OMAP voltage layer updates towards supporting auto-retention/auto-off 2012-11-06 17:06:37 -08:00
vp.h ARM: OMAP3+: voltage: introduce omap vc / vp params for voltagedomains 2012-11-05 15:08:22 -08:00
wd_timer.c ARM: OMAP2+: raw read and write endian fix 2014-05-08 07:09:53 -07:00
wd_timer.h ARM: OMAP: Make plat/omap_hwmod.h local to mach-omap2 2012-10-18 16:05:55 -07:00