linux/arch/arm/plat-mxc/Kconfig
Sascha Hauer ec4bb253fc ARM i.MX51: Make CONFIG_MXC_TZIC an invisible option
There's no point showing this option to the user. The correct
value will be selected anyway.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2010-11-24 10:08:59 +01:00

123 lines
2.7 KiB
Plaintext

if ARCH_MXC
source "arch/arm/plat-mxc/devices/Kconfig"
menu "Freescale MXC Implementations"
choice
prompt "Freescale CPU family:"
default ARCH_MX3
config ARCH_MX1
bool "MX1-based"
select SOC_IMX1
help
This enables support for systems based on the Freescale i.MX1 family
config ARCH_MX2
bool "MX2-based"
help
This enables support for systems based on the Freescale i.MX2 family
config ARCH_MX25
bool "MX25-based"
help
This enables support for systems based on the Freescale i.MX25 family
config ARCH_MX3
bool "MX3-based"
select CPU_V6
help
This enables support for systems based on the Freescale i.MX3 family
config ARCH_MXC91231
bool "MXC91231-based"
select CPU_V6
help
This enables support for systems based on the Freescale MXC91231 family
config ARCH_MX5
bool "MX5-based"
select CPU_V7
select ARM_L1_CACHE_SHIFT_6
help
This enables support for systems based on the Freescale i.MX51 family
endchoice
source "arch/arm/mach-imx/Kconfig"
source "arch/arm/mach-mx3/Kconfig"
source "arch/arm/mach-mxc91231/Kconfig"
source "arch/arm/mach-mx5/Kconfig"
endmenu
config MXC_IRQ_PRIOR
bool "Use IRQ priority"
help
Select this if you want to use prioritized IRQ handling.
This feature prevents higher priority ISR to be interrupted
by lower priority IRQ even IRQF_DISABLED flag is not set.
This may be useful in embedded applications, where are strong
requirements for timing.
Say N here, unless you have a specialized requirement.
config MXC_TZIC
bool
config MXC_AVIC
bool
config MXC_PWM
tristate "Enable PWM driver"
select HAVE_PWM
help
Enable support for the i.MX PWM controller(s).
config MXC_DEBUG_BOARD
bool "Enable MXC debug board(for 3-stack)"
help
The debug board is an integral part of the MXC 3-stack(PDK)
platforms, it can be attached or removed from the peripheral
board. On debug board, several debug devices(ethernet, UART,
buttons, LEDs and JTAG) are implemented. Between the MCU and
these devices, a CPLD is added as a bridge which performs
data/address de-multiplexing and decode, signal level shift,
interrupt control and various board functions.
config HAVE_EPIT
bool
config MXC_USE_EPIT
bool "Use EPIT instead of GPT"
depends on HAVE_EPIT
help
Use EPIT as the system timer on systems that have it. Normally you
don't have a reason to do so as the EPIT has the same features and
uses the same clocks as the GPT. Anyway, on some systems the GPT
may be in use for other purposes.
config MXC_ULPI
bool
config ARCH_HAS_RNGA
bool
config IMX_HAVE_IOMUX_V1
bool
config ARCH_MXC_IOMUX_V3
bool
config ARCH_MXC_AUDMUX_V1
bool
config ARCH_MXC_AUDMUX_V2
bool
config IRAM_ALLOC
bool
select GENERIC_ALLOCATOR
endif