mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-21 18:14:48 +08:00
add513be1c
Add support for "ina231" as compatible string, and update Documentation and Kconfig accordingly. Tested with the Exynos5422-based odroid-xu3 board which has on-board INA231 sensors. Signed-off-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
65 lines
2.3 KiB
Plaintext
65 lines
2.3 KiB
Plaintext
Kernel driver ina2xx
|
|
====================
|
|
|
|
Supported chips:
|
|
* Texas Instruments INA219
|
|
Prefix: 'ina219'
|
|
Addresses: I2C 0x40 - 0x4f
|
|
Datasheet: Publicly available at the Texas Instruments website
|
|
http://www.ti.com/
|
|
|
|
* Texas Instruments INA220
|
|
Prefix: 'ina220'
|
|
Addresses: I2C 0x40 - 0x4f
|
|
Datasheet: Publicly available at the Texas Instruments website
|
|
http://www.ti.com/
|
|
|
|
* Texas Instruments INA226
|
|
Prefix: 'ina226'
|
|
Addresses: I2C 0x40 - 0x4f
|
|
Datasheet: Publicly available at the Texas Instruments website
|
|
http://www.ti.com/
|
|
|
|
* Texas Instruments INA230
|
|
Prefix: 'ina230'
|
|
Addresses: I2C 0x40 - 0x4f
|
|
Datasheet: Publicly available at the Texas Instruments website
|
|
http://www.ti.com/
|
|
|
|
* Texas Instruments INA231
|
|
Prefix: 'ina231'
|
|
Addresses: I2C 0x40 - 0x4f
|
|
Datasheet: Publicly available at the Texas Instruments website
|
|
http://www.ti.com/
|
|
|
|
Author: Lothar Felten <l-felten@ti.com>
|
|
|
|
Description
|
|
-----------
|
|
|
|
The INA219 is a high-side current shunt and power monitor with an I2C
|
|
interface. The INA219 monitors both shunt drop and supply voltage, with
|
|
programmable conversion times and filtering.
|
|
|
|
The INA220 is a high or low side current shunt and power monitor with an I2C
|
|
interface. The INA220 monitors both shunt drop and supply voltage.
|
|
|
|
The INA226 is a current shunt and power monitor with an I2C interface.
|
|
The INA226 monitors both a shunt voltage drop and bus supply voltage.
|
|
|
|
INA230 and INA231 are high or low side current shunt and power monitors
|
|
with an I2C interface. The chips monitor both a shunt voltage drop and
|
|
bus supply voltage.
|
|
|
|
The shunt value in micro-ohms can be set via platform data or device tree at
|
|
compile-time or via the shunt_resistor attribute in sysfs at run-time. Please
|
|
refer to the Documentation/devicetree/bindings/i2c/ina2xx.txt for bindings
|
|
if the device tree is used.
|
|
|
|
Additionally ina226 supports update_interval attribute as described in
|
|
Documentation/hwmon/sysfs-interface. Internally the interval is the sum of
|
|
bus and shunt voltage conversion times multiplied by the averaging rate. We
|
|
don't touch the conversion times and only modify the number of averages. The
|
|
lower limit of the update_interval is 2 ms, the upper limit is 2253 ms.
|
|
The actual programmed interval may vary from the desired value.
|