mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-16 08:44:21 +08:00
8a481af10e
To improve human readability and enable automatic validation, the tuples
in the "states" properties of device nodes compatible with
"regulator-gpio" should be grouped, as reported by "make dtbs_check":
$ make dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/regulator/gpio-regulator.yaml
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: regulator-vccq-sdhi0: states:0: Additional items are not allowed (1800000, 0 were unexpected)
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: regulator-vccq-sdhi0: states:0: [3300000, 1, 1800000, 0] is too long
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: regulator-vccq-sdhi1: states:0: Additional items are not allowed (1800000, 0 were unexpected)
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: regulator-vccq-sdhi1: states:0: [3300000, 1, 1800000, 0] is too long
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: regulator-vccq-sdhi2: states:0: Additional items are not allowed (1800000, 0 were unexpected)
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: regulator-vccq-sdhi2: states:0: [3300000, 1, 1800000, 0] is too long
...
Fix this by grouping the tuples using angle brackets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191213164115.3697-2-geert+renesas@glider.be
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
937 lines
16 KiB
Plaintext
937 lines
16 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Device Tree Source for the Lager board
|
|
*
|
|
* Copyright (C) 2013-2014 Renesas Solutions Corp.
|
|
* Copyright (C) 2014 Cogent Embedded, Inc.
|
|
* Copyright (C) 2015-2016 Renesas Electronics Corporation
|
|
*/
|
|
|
|
/*
|
|
* SSI-AK4643
|
|
*
|
|
* SW1: 1: AK4643
|
|
* 2: CN22
|
|
* 3: ADV7511
|
|
*
|
|
* This command is required when Playback/Capture
|
|
*
|
|
* amixer set "LINEOUT Mixer DACL" on
|
|
* amixer set "DVC Out" 100%
|
|
* amixer set "DVC In" 100%
|
|
*
|
|
* You can use Mute
|
|
*
|
|
* amixer set "DVC Out Mute" on
|
|
* amixer set "DVC In Mute" on
|
|
*
|
|
* You can use Volume Ramp
|
|
*
|
|
* amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps"
|
|
* amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
|
|
* amixer set "DVC Out Ramp" on
|
|
* aplay xxx.wav &
|
|
* amixer set "DVC Out" 80% // Volume Down
|
|
* amixer set "DVC Out" 100% // Volume Up
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include "r8a7790.dtsi"
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "Lager";
|
|
compatible = "renesas,lager", "renesas,r8a7790";
|
|
|
|
aliases {
|
|
serial0 = &scif0;
|
|
serial1 = &scifa1;
|
|
i2c8 = &gpioi2c1;
|
|
i2c9 = &gpioi2c2;
|
|
i2c10 = &i2cexio0;
|
|
i2c11 = &i2cexio1;
|
|
i2c12 = &i2chdmi;
|
|
i2c13 = &i2cpwr;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
memory@40000000 {
|
|
device_type = "memory";
|
|
reg = <0 0x40000000 0 0x40000000>;
|
|
};
|
|
|
|
memory@140000000 {
|
|
device_type = "memory";
|
|
reg = <1 0x40000000 0 0xc0000000>;
|
|
};
|
|
|
|
lbsc {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
};
|
|
|
|
keyboard {
|
|
compatible = "gpio-keys";
|
|
|
|
one {
|
|
linux,code = <KEY_1>;
|
|
label = "SW2-1";
|
|
wakeup-source;
|
|
debounce-interval = <20>;
|
|
gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
|
|
};
|
|
two {
|
|
linux,code = <KEY_2>;
|
|
label = "SW2-2";
|
|
wakeup-source;
|
|
debounce-interval = <20>;
|
|
gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
|
|
};
|
|
three {
|
|
linux,code = <KEY_3>;
|
|
label = "SW2-3";
|
|
wakeup-source;
|
|
debounce-interval = <20>;
|
|
gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
|
|
};
|
|
four {
|
|
linux,code = <KEY_4>;
|
|
label = "SW2-4";
|
|
wakeup-source;
|
|
debounce-interval = <20>;
|
|
gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
led6 {
|
|
gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
led7 {
|
|
gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
led8 {
|
|
gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
fixedregulator3v3: regulator-3v3 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "fixed-3.3V";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
vcc_sdhi0: regulator-vcc-sdhi0 {
|
|
compatible = "regulator-fixed";
|
|
|
|
regulator-name = "SDHI0 Vcc";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
|
|
gpio = <&gpio5 24 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
};
|
|
|
|
vccq_sdhi0: regulator-vccq-sdhi0 {
|
|
compatible = "regulator-gpio";
|
|
|
|
regulator-name = "SDHI0 VccQ";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
|
|
gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
|
|
gpios-states = <1>;
|
|
states = <3300000 1>, <1800000 0>;
|
|
};
|
|
|
|
vcc_sdhi2: regulator-vcc-sdhi2 {
|
|
compatible = "regulator-fixed";
|
|
|
|
regulator-name = "SDHI2 Vcc";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
|
|
gpio = <&gpio5 25 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
};
|
|
|
|
vccq_sdhi2: regulator-vccq-sdhi2 {
|
|
compatible = "regulator-gpio";
|
|
|
|
regulator-name = "SDHI2 VccQ";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
|
|
gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>;
|
|
gpios-states = <1>;
|
|
states = <3300000 1>, <1800000 0>;
|
|
};
|
|
|
|
audio_clock: audio_clock {
|
|
compatible = "fixed-clock";
|
|
#clock-cells = <0>;
|
|
clock-frequency = <11289600>;
|
|
};
|
|
|
|
rsnd_ak4643: sound {
|
|
compatible = "simple-audio-card";
|
|
|
|
simple-audio-card,format = "left_j";
|
|
simple-audio-card,bitclock-master = <&sndcodec>;
|
|
simple-audio-card,frame-master = <&sndcodec>;
|
|
|
|
sndcpu: simple-audio-card,cpu {
|
|
sound-dai = <&rcar_sound>;
|
|
};
|
|
|
|
sndcodec: simple-audio-card,codec {
|
|
sound-dai = <&ak4643>;
|
|
clocks = <&audio_clock>;
|
|
};
|
|
};
|
|
|
|
vga-encoder {
|
|
compatible = "adi,adv7123";
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
adv7123_in: endpoint {
|
|
remote-endpoint = <&du_out_rgb>;
|
|
};
|
|
};
|
|
port@1 {
|
|
reg = <1>;
|
|
adv7123_out: endpoint {
|
|
remote-endpoint = <&vga_in>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
vga {
|
|
compatible = "vga-connector";
|
|
|
|
port {
|
|
vga_in: endpoint {
|
|
remote-endpoint = <&adv7123_out>;
|
|
};
|
|
};
|
|
};
|
|
|
|
hdmi-in {
|
|
compatible = "hdmi-connector";
|
|
type = "a";
|
|
|
|
port {
|
|
hdmi_con_in: endpoint {
|
|
remote-endpoint = <&adv7612_in>;
|
|
};
|
|
};
|
|
};
|
|
|
|
cec_clock: cec-clock {
|
|
compatible = "fixed-clock";
|
|
#clock-cells = <0>;
|
|
clock-frequency = <12000000>;
|
|
};
|
|
|
|
hdmi-out {
|
|
compatible = "hdmi-connector";
|
|
type = "a";
|
|
|
|
port {
|
|
hdmi_con_out: endpoint {
|
|
remote-endpoint = <&adv7511_out>;
|
|
};
|
|
};
|
|
};
|
|
|
|
x2_clk: x2-clock {
|
|
compatible = "fixed-clock";
|
|
#clock-cells = <0>;
|
|
clock-frequency = <148500000>;
|
|
};
|
|
|
|
x13_clk: x13-clock {
|
|
compatible = "fixed-clock";
|
|
#clock-cells = <0>;
|
|
clock-frequency = <148500000>;
|
|
};
|
|
|
|
gpioi2c1: i2c-8 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "i2c-gpio";
|
|
status = "disabled";
|
|
scl-gpios = <&gpio1 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
sda-gpios = <&gpio1 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
i2c-gpio,delay-us = <5>;
|
|
};
|
|
|
|
gpioi2c2: i2c-9 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "i2c-gpio";
|
|
status = "disabled";
|
|
scl-gpios = <&gpio5 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
sda-gpios = <&gpio5 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
i2c-gpio,delay-us = <5>;
|
|
};
|
|
|
|
/*
|
|
* IIC0/I2C0 is routed to EXIO connector A, pins 114 (SCL) + 116 (SDA) only.
|
|
* We use the I2C demuxer, so the desired IP core can be selected at runtime
|
|
* depending on the use case (e.g. DMA with IIC0 or slave support with I2C0).
|
|
* Note: For testing the I2C slave feature, it is convenient to connect this
|
|
* bus with IIC3 on pins 110 (SCL) + 112 (SDA), select I2C0 at runtime, and
|
|
* instantiate the slave device at runtime according to the documentation.
|
|
* You can then communicate with the slave via IIC3.
|
|
*
|
|
* IIC0/I2C0 does not appear to support fallback to GPIO.
|
|
*/
|
|
i2cexio0: i2c-10 {
|
|
compatible = "i2c-demux-pinctrl";
|
|
i2c-parent = <&iic0>, <&i2c0>;
|
|
i2c-bus-name = "i2c-exio0";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
};
|
|
|
|
/*
|
|
* IIC1/I2C1 is routed to EXIO connector A, pins 78 (SCL) + 80 (SDA).
|
|
* This is similar to the arangement described for i2cexio0 (above)
|
|
* with a fallback to GPIO also provided.
|
|
*/
|
|
i2cexio1: i2c-11 {
|
|
compatible = "i2c-demux-pinctrl";
|
|
i2c-parent = <&iic1>, <&i2c1>, <&gpioi2c1>;
|
|
i2c-bus-name = "i2c-exio1";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
};
|
|
|
|
/*
|
|
* IIC2 and I2C2 may be switched using pinmux.
|
|
* A fallback to GPIO is also provided.
|
|
*/
|
|
i2chdmi: i2c-12 {
|
|
compatible = "i2c-demux-pinctrl";
|
|
i2c-parent = <&iic2>, <&i2c2>, <&gpioi2c2>;
|
|
i2c-bus-name = "i2c-hdmi";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
ak4643: codec@12 {
|
|
compatible = "asahi-kasei,ak4643";
|
|
#sound-dai-cells = <0>;
|
|
reg = <0x12>;
|
|
};
|
|
|
|
composite-in@20 {
|
|
compatible = "adi,adv7180";
|
|
reg = <0x20>;
|
|
remote = <&vin1>;
|
|
|
|
port {
|
|
adv7180: endpoint {
|
|
bus-width = <8>;
|
|
remote-endpoint = <&vin1ep0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
hdmi@39 {
|
|
compatible = "adi,adv7511w";
|
|
reg = <0x39>;
|
|
interrupt-parent = <&gpio1>;
|
|
interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
|
|
clocks = <&cec_clock>;
|
|
clock-names = "cec";
|
|
|
|
adi,input-depth = <8>;
|
|
adi,input-colorspace = "rgb";
|
|
adi,input-clock = "1x";
|
|
adi,input-style = <1>;
|
|
adi,input-justification = "evenly";
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
adv7511_in: endpoint {
|
|
remote-endpoint = <&lvds0_out>;
|
|
};
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
adv7511_out: endpoint {
|
|
remote-endpoint = <&hdmi_con_out>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
hdmi-in@4c {
|
|
compatible = "adi,adv7612";
|
|
reg = <0x4c>;
|
|
interrupt-parent = <&gpio1>;
|
|
interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
|
|
default-input = <0>;
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
adv7612_in: endpoint {
|
|
remote-endpoint = <&hdmi_con_in>;
|
|
};
|
|
};
|
|
|
|
port@2 {
|
|
reg = <2>;
|
|
adv7612_out: endpoint {
|
|
remote-endpoint = <&vin0ep2>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
/*
|
|
* IIC3 and I2C3 may be switched using pinmux.
|
|
* IIC3/I2C3 does not appear to support fallback to GPIO.
|
|
*/
|
|
i2cpwr: i2c-13 {
|
|
compatible = "i2c-demux-pinctrl";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pmic_irq_pins>;
|
|
i2c-parent = <&iic3>, <&i2c3>;
|
|
i2c-bus-name = "i2c-pwr";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pmic@58 {
|
|
compatible = "dlg,da9063";
|
|
reg = <0x58>;
|
|
interrupt-parent = <&irqc0>;
|
|
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
|
|
interrupt-controller;
|
|
|
|
rtc {
|
|
compatible = "dlg,da9063-rtc";
|
|
};
|
|
|
|
wdt {
|
|
compatible = "dlg,da9063-watchdog";
|
|
};
|
|
};
|
|
|
|
vdd_dvfs: regulator@68 {
|
|
compatible = "dlg,da9210";
|
|
reg = <0x68>;
|
|
interrupt-parent = <&irqc0>;
|
|
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
|
|
|
|
regulator-min-microvolt = <1000000>;
|
|
regulator-max-microvolt = <1000000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
};
|
|
};
|
|
|
|
&du {
|
|
pinctrl-0 = <&du_pins>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
|
|
clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>,
|
|
<&x13_clk>, <&x2_clk>;
|
|
clock-names = "du.0", "du.1", "du.2", "dclkin.0", "dclkin.1";
|
|
|
|
ports {
|
|
port@0 {
|
|
endpoint {
|
|
remote-endpoint = <&adv7123_in>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&lvds0 {
|
|
status = "okay";
|
|
|
|
ports {
|
|
port@1 {
|
|
endpoint {
|
|
remote-endpoint = <&adv7511_in>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&lvds1 {
|
|
ports {
|
|
port@1 {
|
|
lvds_connector: endpoint {
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&extal_clk {
|
|
clock-frequency = <20000000>;
|
|
};
|
|
|
|
&pfc {
|
|
pinctrl-0 = <&scif_clk_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
du_pins: du {
|
|
groups = "du_rgb666", "du_sync_1", "du_clk_out_0";
|
|
function = "du";
|
|
};
|
|
|
|
scif0_pins: scif0 {
|
|
groups = "scif0_data";
|
|
function = "scif0";
|
|
};
|
|
|
|
scif_clk_pins: scif_clk {
|
|
groups = "scif_clk";
|
|
function = "scif_clk";
|
|
};
|
|
|
|
ether_pins: ether {
|
|
groups = "eth_link", "eth_mdio", "eth_rmii";
|
|
function = "eth";
|
|
};
|
|
|
|
phy1_pins: phy1 {
|
|
groups = "intc_irq0";
|
|
function = "intc";
|
|
};
|
|
|
|
scifa1_pins: scifa1 {
|
|
groups = "scifa1_data";
|
|
function = "scifa1";
|
|
};
|
|
|
|
sdhi0_pins: sd0 {
|
|
groups = "sdhi0_data4", "sdhi0_ctrl";
|
|
function = "sdhi0";
|
|
power-source = <3300>;
|
|
};
|
|
|
|
sdhi0_pins_uhs: sd0_uhs {
|
|
groups = "sdhi0_data4", "sdhi0_ctrl";
|
|
function = "sdhi0";
|
|
power-source = <1800>;
|
|
};
|
|
|
|
sdhi2_pins: sd2 {
|
|
groups = "sdhi2_data4", "sdhi2_ctrl";
|
|
function = "sdhi2";
|
|
power-source = <3300>;
|
|
};
|
|
|
|
sdhi2_pins_uhs: sd2_uhs {
|
|
groups = "sdhi2_data4", "sdhi2_ctrl";
|
|
function = "sdhi2";
|
|
power-source = <1800>;
|
|
};
|
|
|
|
mmc1_pins: mmc1 {
|
|
groups = "mmc1_data8", "mmc1_ctrl";
|
|
function = "mmc1";
|
|
};
|
|
|
|
qspi_pins: qspi {
|
|
groups = "qspi_ctrl", "qspi_data4";
|
|
function = "qspi";
|
|
};
|
|
|
|
msiof1_pins: msiof1 {
|
|
groups = "msiof1_clk", "msiof1_sync", "msiof1_rx",
|
|
"msiof1_tx";
|
|
function = "msiof1";
|
|
};
|
|
|
|
i2c0_pins: i2c0 {
|
|
groups = "i2c0";
|
|
function = "i2c0";
|
|
};
|
|
|
|
iic0_pins: iic0 {
|
|
groups = "iic0";
|
|
function = "iic0";
|
|
};
|
|
|
|
i2c1_pins: i2c1 {
|
|
groups = "i2c1";
|
|
function = "i2c1";
|
|
};
|
|
|
|
iic1_pins: iic1 {
|
|
groups = "iic1";
|
|
function = "iic1";
|
|
};
|
|
|
|
i2c2_pins: i2c2 {
|
|
groups = "i2c2";
|
|
function = "i2c2";
|
|
};
|
|
|
|
iic2_pins: iic2 {
|
|
groups = "iic2";
|
|
function = "iic2";
|
|
};
|
|
|
|
i2c3_pins: i2c3 {
|
|
groups = "i2c3";
|
|
function = "i2c3";
|
|
};
|
|
|
|
iic3_pins: iic3 {
|
|
groups = "iic3";
|
|
function = "iic3";
|
|
};
|
|
|
|
pmic_irq_pins: pmicirq {
|
|
groups = "intc_irq2";
|
|
function = "intc";
|
|
};
|
|
|
|
hsusb_pins: hsusb {
|
|
groups = "usb0_ovc_vbus";
|
|
function = "usb0";
|
|
};
|
|
|
|
usb0_pins: usb0 {
|
|
groups = "usb0";
|
|
function = "usb0";
|
|
};
|
|
|
|
usb1_pins: usb1 {
|
|
groups = "usb1";
|
|
function = "usb1";
|
|
};
|
|
|
|
usb2_pins: usb2 {
|
|
groups = "usb2";
|
|
function = "usb2";
|
|
};
|
|
|
|
vin0_pins: vin0 {
|
|
groups = "vin0_data24", "vin0_sync", "vin0_clkenb", "vin0_clk";
|
|
function = "vin0";
|
|
};
|
|
|
|
vin1_pins: vin1 {
|
|
groups = "vin1_data8", "vin1_clk";
|
|
function = "vin1";
|
|
};
|
|
|
|
sound_pins: sound {
|
|
groups = "ssi0129_ctrl", "ssi0_data", "ssi1_data";
|
|
function = "ssi";
|
|
};
|
|
|
|
sound_clk_pins: sound_clk {
|
|
groups = "audio_clk_a";
|
|
function = "audio_clk";
|
|
};
|
|
};
|
|
|
|
ðer {
|
|
pinctrl-0 = <ðer_pins &phy1_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
phy-handle = <&phy1>;
|
|
renesas,ether-link-active-low;
|
|
status = "okay";
|
|
|
|
phy1: ethernet-phy@1 {
|
|
reg = <1>;
|
|
interrupt-parent = <&irqc0>;
|
|
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
|
|
micrel,led-mode = <1>;
|
|
};
|
|
};
|
|
|
|
&cmt0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&mmcif1 {
|
|
pinctrl-0 = <&mmc1_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
vmmc-supply = <&fixedregulator3v3>;
|
|
bus-width = <8>;
|
|
non-removable;
|
|
status = "okay";
|
|
};
|
|
|
|
&sata1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&qspi {
|
|
pinctrl-0 = <&qspi_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
status = "okay";
|
|
|
|
flash: flash@0 {
|
|
compatible = "spansion,s25fl512s", "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <30000000>;
|
|
spi-tx-bus-width = <4>;
|
|
spi-rx-bus-width = <4>;
|
|
spi-cpha;
|
|
spi-cpol;
|
|
m25p,fast-read;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "loader";
|
|
reg = <0x00000000 0x00040000>;
|
|
read-only;
|
|
};
|
|
partition@40000 {
|
|
label = "user";
|
|
reg = <0x00040000 0x00400000>;
|
|
read-only;
|
|
};
|
|
partition@440000 {
|
|
label = "flash";
|
|
reg = <0x00440000 0x03bc0000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&scif0 {
|
|
pinctrl-0 = <&scif0_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&scifa1 {
|
|
pinctrl-0 = <&scifa1_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&scif_clk {
|
|
clock-frequency = <14745600>;
|
|
};
|
|
|
|
&msiof1 {
|
|
pinctrl-0 = <&msiof1_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
status = "okay";
|
|
|
|
pmic: pmic@0 {
|
|
compatible = "renesas,r2a11302ft";
|
|
reg = <0>;
|
|
spi-max-frequency = <6000000>;
|
|
spi-cpol;
|
|
spi-cpha;
|
|
};
|
|
};
|
|
|
|
&sdhi0 {
|
|
pinctrl-0 = <&sdhi0_pins>;
|
|
pinctrl-1 = <&sdhi0_pins_uhs>;
|
|
pinctrl-names = "default", "state_uhs";
|
|
|
|
vmmc-supply = <&vcc_sdhi0>;
|
|
vqmmc-supply = <&vccq_sdhi0>;
|
|
cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
|
|
sd-uhs-sdr50;
|
|
sd-uhs-sdr104;
|
|
status = "okay";
|
|
};
|
|
|
|
&sdhi2 {
|
|
pinctrl-0 = <&sdhi2_pins>;
|
|
pinctrl-1 = <&sdhi2_pins_uhs>;
|
|
pinctrl-names = "default", "state_uhs";
|
|
|
|
vmmc-supply = <&vcc_sdhi2>;
|
|
vqmmc-supply = <&vccq_sdhi2>;
|
|
cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
|
|
sd-uhs-sdr50;
|
|
status = "okay";
|
|
};
|
|
|
|
&cpu0 {
|
|
cpu0-supply = <&vdd_dvfs>;
|
|
};
|
|
|
|
&i2c0 {
|
|
pinctrl-0 = <&i2c0_pins>;
|
|
pinctrl-names = "i2c-exio0";
|
|
};
|
|
|
|
&iic0 {
|
|
pinctrl-0 = <&iic0_pins>;
|
|
pinctrl-names = "i2c-exio0";
|
|
};
|
|
|
|
&i2c1 {
|
|
pinctrl-0 = <&i2c1_pins>;
|
|
pinctrl-names = "i2c-exio1";
|
|
};
|
|
|
|
&iic1 {
|
|
pinctrl-0 = <&iic1_pins>;
|
|
pinctrl-names = "i2c-exio1";
|
|
};
|
|
|
|
&i2c2 {
|
|
pinctrl-0 = <&i2c2_pins>;
|
|
pinctrl-names = "i2c-hdmi";
|
|
|
|
clock-frequency = <100000>;
|
|
};
|
|
|
|
&iic2 {
|
|
pinctrl-0 = <&iic2_pins>;
|
|
pinctrl-names = "i2c-hdmi";
|
|
|
|
clock-frequency = <100000>;
|
|
};
|
|
|
|
&i2c3 {
|
|
pinctrl-0 = <&i2c3_pins>;
|
|
pinctrl-names = "i2c-pwr";
|
|
};
|
|
|
|
&iic3 {
|
|
pinctrl-0 = <&iic3_pins>;
|
|
pinctrl-names = "i2c-pwr";
|
|
};
|
|
|
|
&pci0 {
|
|
status = "okay";
|
|
pinctrl-0 = <&usb0_pins>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
&pci1 {
|
|
status = "okay";
|
|
pinctrl-0 = <&usb1_pins>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
&xhci {
|
|
status = "okay";
|
|
pinctrl-0 = <&usb2_pins>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
&pci2 {
|
|
status = "okay";
|
|
pinctrl-0 = <&usb2_pins>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
&hsusb {
|
|
status = "okay";
|
|
pinctrl-0 = <&hsusb_pins>;
|
|
pinctrl-names = "default";
|
|
renesas,enable-gpio = <&gpio5 18 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
&usbphy {
|
|
status = "okay";
|
|
};
|
|
|
|
/* HDMI video input */
|
|
&vin0 {
|
|
pinctrl-0 = <&vin0_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
status = "okay";
|
|
|
|
port {
|
|
vin0ep2: endpoint {
|
|
remote-endpoint = <&adv7612_out>;
|
|
bus-width = <24>;
|
|
hsync-active = <0>;
|
|
vsync-active = <0>;
|
|
pclk-sample = <1>;
|
|
data-active = <1>;
|
|
};
|
|
};
|
|
};
|
|
|
|
/* composite video input */
|
|
&vin1 {
|
|
pinctrl-0 = <&vin1_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
status = "okay";
|
|
|
|
port {
|
|
vin1ep0: endpoint {
|
|
remote-endpoint = <&adv7180>;
|
|
bus-width = <8>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&rcar_sound {
|
|
pinctrl-0 = <&sound_pins &sound_clk_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
/* Single DAI */
|
|
#sound-dai-cells = <0>;
|
|
|
|
status = "okay";
|
|
|
|
rcar_sound,dai {
|
|
dai0 {
|
|
playback = <&ssi0 &src2 &dvc0>;
|
|
capture = <&ssi1 &src3 &dvc1>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&rwdt {
|
|
timeout-sec = <60>;
|
|
status = "okay";
|
|
};
|
|
|
|
&ssi1 {
|
|
shared-pin;
|
|
};
|