mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-15 23:14:31 +08:00
9fd097b149
In-kernel disk event polling doesn't matter for legacy/fringe drivers and may lead to infinite event loop if ->check_events() implementation generates events on level condition instead of edge. Now that block layer supports suppressing exporting unlisted events, simply leaving disk->events cleared allows these drivers to keep the internal revalidation behavior intact while avoiding weird interactions with userland event handler. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
1214 lines
30 KiB
C
1214 lines
30 KiB
C
/*
|
|
* Driver for the SWIM3 (Super Woz Integrated Machine 3)
|
|
* floppy controller found on Power Macintoshes.
|
|
*
|
|
* Copyright (C) 1996 Paul Mackerras.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* as published by the Free Software Foundation; either version
|
|
* 2 of the License, or (at your option) any later version.
|
|
*/
|
|
|
|
/*
|
|
* TODO:
|
|
* handle 2 drives
|
|
* handle GCR disks
|
|
*/
|
|
|
|
#include <linux/stddef.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/sched.h>
|
|
#include <linux/timer.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/fd.h>
|
|
#include <linux/ioctl.h>
|
|
#include <linux/blkdev.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/mutex.h>
|
|
#include <linux/module.h>
|
|
#include <linux/spinlock.h>
|
|
#include <asm/io.h>
|
|
#include <asm/dbdma.h>
|
|
#include <asm/prom.h>
|
|
#include <asm/uaccess.h>
|
|
#include <asm/mediabay.h>
|
|
#include <asm/machdep.h>
|
|
#include <asm/pmac_feature.h>
|
|
|
|
static DEFINE_MUTEX(swim3_mutex);
|
|
static struct request_queue *swim3_queue;
|
|
static struct gendisk *disks[2];
|
|
static struct request *fd_req;
|
|
|
|
#define MAX_FLOPPIES 2
|
|
|
|
enum swim_state {
|
|
idle,
|
|
locating,
|
|
seeking,
|
|
settling,
|
|
do_transfer,
|
|
jogging,
|
|
available,
|
|
revalidating,
|
|
ejecting
|
|
};
|
|
|
|
#define REG(x) unsigned char x; char x ## _pad[15];
|
|
|
|
/*
|
|
* The names for these registers mostly represent speculation on my part.
|
|
* It will be interesting to see how close they are to the names Apple uses.
|
|
*/
|
|
struct swim3 {
|
|
REG(data);
|
|
REG(timer); /* counts down at 1MHz */
|
|
REG(error);
|
|
REG(mode);
|
|
REG(select); /* controls CA0, CA1, CA2 and LSTRB signals */
|
|
REG(setup);
|
|
REG(control); /* writing bits clears them */
|
|
REG(status); /* writing bits sets them in control */
|
|
REG(intr);
|
|
REG(nseek); /* # tracks to seek */
|
|
REG(ctrack); /* current track number */
|
|
REG(csect); /* current sector number */
|
|
REG(gap3); /* size of gap 3 in track format */
|
|
REG(sector); /* sector # to read or write */
|
|
REG(nsect); /* # sectors to read or write */
|
|
REG(intr_enable);
|
|
};
|
|
|
|
#define control_bic control
|
|
#define control_bis status
|
|
|
|
/* Bits in select register */
|
|
#define CA_MASK 7
|
|
#define LSTRB 8
|
|
|
|
/* Bits in control register */
|
|
#define DO_SEEK 0x80
|
|
#define FORMAT 0x40
|
|
#define SELECT 0x20
|
|
#define WRITE_SECTORS 0x10
|
|
#define DO_ACTION 0x08
|
|
#define DRIVE2_ENABLE 0x04
|
|
#define DRIVE_ENABLE 0x02
|
|
#define INTR_ENABLE 0x01
|
|
|
|
/* Bits in status register */
|
|
#define FIFO_1BYTE 0x80
|
|
#define FIFO_2BYTE 0x40
|
|
#define ERROR 0x20
|
|
#define DATA 0x08
|
|
#define RDDATA 0x04
|
|
#define INTR_PENDING 0x02
|
|
#define MARK_BYTE 0x01
|
|
|
|
/* Bits in intr and intr_enable registers */
|
|
#define ERROR_INTR 0x20
|
|
#define DATA_CHANGED 0x10
|
|
#define TRANSFER_DONE 0x08
|
|
#define SEEN_SECTOR 0x04
|
|
#define SEEK_DONE 0x02
|
|
#define TIMER_DONE 0x01
|
|
|
|
/* Bits in error register */
|
|
#define ERR_DATA_CRC 0x80
|
|
#define ERR_ADDR_CRC 0x40
|
|
#define ERR_OVERRUN 0x04
|
|
#define ERR_UNDERRUN 0x01
|
|
|
|
/* Bits in setup register */
|
|
#define S_SW_RESET 0x80
|
|
#define S_GCR_WRITE 0x40
|
|
#define S_IBM_DRIVE 0x20
|
|
#define S_TEST_MODE 0x10
|
|
#define S_FCLK_DIV2 0x08
|
|
#define S_GCR 0x04
|
|
#define S_COPY_PROT 0x02
|
|
#define S_INV_WDATA 0x01
|
|
|
|
/* Select values for swim3_action */
|
|
#define SEEK_POSITIVE 0
|
|
#define SEEK_NEGATIVE 4
|
|
#define STEP 1
|
|
#define MOTOR_ON 2
|
|
#define MOTOR_OFF 6
|
|
#define INDEX 3
|
|
#define EJECT 7
|
|
#define SETMFM 9
|
|
#define SETGCR 13
|
|
|
|
/* Select values for swim3_select and swim3_readbit */
|
|
#define STEP_DIR 0
|
|
#define STEPPING 1
|
|
#define MOTOR_ON 2
|
|
#define RELAX 3 /* also eject in progress */
|
|
#define READ_DATA_0 4
|
|
#define TWOMEG_DRIVE 5
|
|
#define SINGLE_SIDED 6 /* drive or diskette is 4MB type? */
|
|
#define DRIVE_PRESENT 7
|
|
#define DISK_IN 8
|
|
#define WRITE_PROT 9
|
|
#define TRACK_ZERO 10
|
|
#define TACHO 11
|
|
#define READ_DATA_1 12
|
|
#define MFM_MODE 13
|
|
#define SEEK_COMPLETE 14
|
|
#define ONEMEG_MEDIA 15
|
|
|
|
/* Definitions of values used in writing and formatting */
|
|
#define DATA_ESCAPE 0x99
|
|
#define GCR_SYNC_EXC 0x3f
|
|
#define GCR_SYNC_CONV 0x80
|
|
#define GCR_FIRST_MARK 0xd5
|
|
#define GCR_SECOND_MARK 0xaa
|
|
#define GCR_ADDR_MARK "\xd5\xaa\x00"
|
|
#define GCR_DATA_MARK "\xd5\xaa\x0b"
|
|
#define GCR_SLIP_BYTE "\x27\xaa"
|
|
#define GCR_SELF_SYNC "\x3f\xbf\x1e\x34\x3c\x3f"
|
|
|
|
#define DATA_99 "\x99\x99"
|
|
#define MFM_ADDR_MARK "\x99\xa1\x99\xa1\x99\xa1\x99\xfe"
|
|
#define MFM_INDEX_MARK "\x99\xc2\x99\xc2\x99\xc2\x99\xfc"
|
|
#define MFM_GAP_LEN 12
|
|
|
|
struct floppy_state {
|
|
enum swim_state state;
|
|
spinlock_t lock;
|
|
struct swim3 __iomem *swim3; /* hardware registers */
|
|
struct dbdma_regs __iomem *dma; /* DMA controller registers */
|
|
int swim3_intr; /* interrupt number for SWIM3 */
|
|
int dma_intr; /* interrupt number for DMA channel */
|
|
int cur_cyl; /* cylinder head is on, or -1 */
|
|
int cur_sector; /* last sector we saw go past */
|
|
int req_cyl; /* the cylinder for the current r/w request */
|
|
int head; /* head number ditto */
|
|
int req_sector; /* sector number ditto */
|
|
int scount; /* # sectors we're transferring at present */
|
|
int retries;
|
|
int settle_time;
|
|
int secpercyl; /* disk geometry information */
|
|
int secpertrack;
|
|
int total_secs;
|
|
int write_prot; /* 1 if write-protected, 0 if not, -1 dunno */
|
|
struct dbdma_cmd *dma_cmd;
|
|
int ref_count;
|
|
int expect_cyl;
|
|
struct timer_list timeout;
|
|
int timeout_pending;
|
|
int ejected;
|
|
wait_queue_head_t wait;
|
|
int wanted;
|
|
struct macio_dev *mdev;
|
|
char dbdma_cmd_space[5 * sizeof(struct dbdma_cmd)];
|
|
};
|
|
|
|
static struct floppy_state floppy_states[MAX_FLOPPIES];
|
|
static int floppy_count = 0;
|
|
static DEFINE_SPINLOCK(swim3_lock);
|
|
|
|
static unsigned short write_preamble[] = {
|
|
0x4e4e, 0x4e4e, 0x4e4e, 0x4e4e, 0x4e4e, /* gap field */
|
|
0, 0, 0, 0, 0, 0, /* sync field */
|
|
0x99a1, 0x99a1, 0x99a1, 0x99fb, /* data address mark */
|
|
0x990f /* no escape for 512 bytes */
|
|
};
|
|
|
|
static unsigned short write_postamble[] = {
|
|
0x9904, /* insert CRC */
|
|
0x4e4e, 0x4e4e,
|
|
0x9908, /* stop writing */
|
|
0, 0, 0, 0, 0, 0
|
|
};
|
|
|
|
static void swim3_select(struct floppy_state *fs, int sel);
|
|
static void swim3_action(struct floppy_state *fs, int action);
|
|
static int swim3_readbit(struct floppy_state *fs, int bit);
|
|
static void do_fd_request(struct request_queue * q);
|
|
static void start_request(struct floppy_state *fs);
|
|
static void set_timeout(struct floppy_state *fs, int nticks,
|
|
void (*proc)(unsigned long));
|
|
static void scan_track(struct floppy_state *fs);
|
|
static void seek_track(struct floppy_state *fs, int n);
|
|
static void init_dma(struct dbdma_cmd *cp, int cmd, void *buf, int count);
|
|
static void setup_transfer(struct floppy_state *fs);
|
|
static void act(struct floppy_state *fs);
|
|
static void scan_timeout(unsigned long data);
|
|
static void seek_timeout(unsigned long data);
|
|
static void settle_timeout(unsigned long data);
|
|
static void xfer_timeout(unsigned long data);
|
|
static irqreturn_t swim3_interrupt(int irq, void *dev_id);
|
|
/*static void fd_dma_interrupt(int irq, void *dev_id);*/
|
|
static int grab_drive(struct floppy_state *fs, enum swim_state state,
|
|
int interruptible);
|
|
static void release_drive(struct floppy_state *fs);
|
|
static int fd_eject(struct floppy_state *fs);
|
|
static int floppy_ioctl(struct block_device *bdev, fmode_t mode,
|
|
unsigned int cmd, unsigned long param);
|
|
static int floppy_open(struct block_device *bdev, fmode_t mode);
|
|
static int floppy_release(struct gendisk *disk, fmode_t mode);
|
|
static unsigned int floppy_check_events(struct gendisk *disk,
|
|
unsigned int clearing);
|
|
static int floppy_revalidate(struct gendisk *disk);
|
|
|
|
static bool swim3_end_request(int err, unsigned int nr_bytes)
|
|
{
|
|
if (__blk_end_request(fd_req, err, nr_bytes))
|
|
return true;
|
|
|
|
fd_req = NULL;
|
|
return false;
|
|
}
|
|
|
|
static bool swim3_end_request_cur(int err)
|
|
{
|
|
return swim3_end_request(err, blk_rq_cur_bytes(fd_req));
|
|
}
|
|
|
|
static void swim3_select(struct floppy_state *fs, int sel)
|
|
{
|
|
struct swim3 __iomem *sw = fs->swim3;
|
|
|
|
out_8(&sw->select, RELAX);
|
|
if (sel & 8)
|
|
out_8(&sw->control_bis, SELECT);
|
|
else
|
|
out_8(&sw->control_bic, SELECT);
|
|
out_8(&sw->select, sel & CA_MASK);
|
|
}
|
|
|
|
static void swim3_action(struct floppy_state *fs, int action)
|
|
{
|
|
struct swim3 __iomem *sw = fs->swim3;
|
|
|
|
swim3_select(fs, action);
|
|
udelay(1);
|
|
out_8(&sw->select, sw->select | LSTRB);
|
|
udelay(2);
|
|
out_8(&sw->select, sw->select & ~LSTRB);
|
|
udelay(1);
|
|
}
|
|
|
|
static int swim3_readbit(struct floppy_state *fs, int bit)
|
|
{
|
|
struct swim3 __iomem *sw = fs->swim3;
|
|
int stat;
|
|
|
|
swim3_select(fs, bit);
|
|
udelay(1);
|
|
stat = in_8(&sw->status);
|
|
return (stat & DATA) == 0;
|
|
}
|
|
|
|
static void do_fd_request(struct request_queue * q)
|
|
{
|
|
int i;
|
|
|
|
for(i=0; i<floppy_count; i++) {
|
|
struct floppy_state *fs = &floppy_states[i];
|
|
if (fs->mdev->media_bay &&
|
|
check_media_bay(fs->mdev->media_bay) != MB_FD)
|
|
continue;
|
|
start_request(fs);
|
|
}
|
|
}
|
|
|
|
static void start_request(struct floppy_state *fs)
|
|
{
|
|
struct request *req;
|
|
unsigned long x;
|
|
|
|
if (fs->state == idle && fs->wanted) {
|
|
fs->state = available;
|
|
wake_up(&fs->wait);
|
|
return;
|
|
}
|
|
while (fs->state == idle) {
|
|
if (!fd_req) {
|
|
fd_req = blk_fetch_request(swim3_queue);
|
|
if (!fd_req)
|
|
break;
|
|
}
|
|
req = fd_req;
|
|
#if 0
|
|
printk("do_fd_req: dev=%s cmd=%d sec=%ld nr_sec=%u buf=%p\n",
|
|
req->rq_disk->disk_name, req->cmd,
|
|
(long)blk_rq_pos(req), blk_rq_sectors(req), req->buffer);
|
|
printk(" errors=%d current_nr_sectors=%u\n",
|
|
req->errors, blk_rq_cur_sectors(req));
|
|
#endif
|
|
|
|
if (blk_rq_pos(req) >= fs->total_secs) {
|
|
swim3_end_request_cur(-EIO);
|
|
continue;
|
|
}
|
|
if (fs->ejected) {
|
|
swim3_end_request_cur(-EIO);
|
|
continue;
|
|
}
|
|
|
|
if (rq_data_dir(req) == WRITE) {
|
|
if (fs->write_prot < 0)
|
|
fs->write_prot = swim3_readbit(fs, WRITE_PROT);
|
|
if (fs->write_prot) {
|
|
swim3_end_request_cur(-EIO);
|
|
continue;
|
|
}
|
|
}
|
|
|
|
/* Do not remove the cast. blk_rq_pos(req) is now a
|
|
* sector_t and can be 64 bits, but it will never go
|
|
* past 32 bits for this driver anyway, so we can
|
|
* safely cast it down and not have to do a 64/32
|
|
* division
|
|
*/
|
|
fs->req_cyl = ((long)blk_rq_pos(req)) / fs->secpercyl;
|
|
x = ((long)blk_rq_pos(req)) % fs->secpercyl;
|
|
fs->head = x / fs->secpertrack;
|
|
fs->req_sector = x % fs->secpertrack + 1;
|
|
fd_req = req;
|
|
fs->state = do_transfer;
|
|
fs->retries = 0;
|
|
|
|
act(fs);
|
|
}
|
|
}
|
|
|
|
static void set_timeout(struct floppy_state *fs, int nticks,
|
|
void (*proc)(unsigned long))
|
|
{
|
|
unsigned long flags;
|
|
|
|
spin_lock_irqsave(&fs->lock, flags);
|
|
if (fs->timeout_pending)
|
|
del_timer(&fs->timeout);
|
|
fs->timeout.expires = jiffies + nticks;
|
|
fs->timeout.function = proc;
|
|
fs->timeout.data = (unsigned long) fs;
|
|
add_timer(&fs->timeout);
|
|
fs->timeout_pending = 1;
|
|
spin_unlock_irqrestore(&fs->lock, flags);
|
|
}
|
|
|
|
static inline void scan_track(struct floppy_state *fs)
|
|
{
|
|
struct swim3 __iomem *sw = fs->swim3;
|
|
|
|
swim3_select(fs, READ_DATA_0);
|
|
in_8(&sw->intr); /* clear SEEN_SECTOR bit */
|
|
in_8(&sw->error);
|
|
out_8(&sw->intr_enable, SEEN_SECTOR);
|
|
out_8(&sw->control_bis, DO_ACTION);
|
|
/* enable intr when track found */
|
|
set_timeout(fs, HZ, scan_timeout); /* enable timeout */
|
|
}
|
|
|
|
static inline void seek_track(struct floppy_state *fs, int n)
|
|
{
|
|
struct swim3 __iomem *sw = fs->swim3;
|
|
|
|
if (n >= 0) {
|
|
swim3_action(fs, SEEK_POSITIVE);
|
|
sw->nseek = n;
|
|
} else {
|
|
swim3_action(fs, SEEK_NEGATIVE);
|
|
sw->nseek = -n;
|
|
}
|
|
fs->expect_cyl = (fs->cur_cyl >= 0)? fs->cur_cyl + n: -1;
|
|
swim3_select(fs, STEP);
|
|
in_8(&sw->error);
|
|
/* enable intr when seek finished */
|
|
out_8(&sw->intr_enable, SEEK_DONE);
|
|
out_8(&sw->control_bis, DO_SEEK);
|
|
set_timeout(fs, 3*HZ, seek_timeout); /* enable timeout */
|
|
fs->settle_time = 0;
|
|
}
|
|
|
|
static inline void init_dma(struct dbdma_cmd *cp, int cmd,
|
|
void *buf, int count)
|
|
{
|
|
st_le16(&cp->req_count, count);
|
|
st_le16(&cp->command, cmd);
|
|
st_le32(&cp->phy_addr, virt_to_bus(buf));
|
|
cp->xfer_status = 0;
|
|
}
|
|
|
|
static inline void setup_transfer(struct floppy_state *fs)
|
|
{
|
|
int n;
|
|
struct swim3 __iomem *sw = fs->swim3;
|
|
struct dbdma_cmd *cp = fs->dma_cmd;
|
|
struct dbdma_regs __iomem *dr = fs->dma;
|
|
|
|
if (blk_rq_cur_sectors(fd_req) <= 0) {
|
|
printk(KERN_ERR "swim3: transfer 0 sectors?\n");
|
|
return;
|
|
}
|
|
if (rq_data_dir(fd_req) == WRITE)
|
|
n = 1;
|
|
else {
|
|
n = fs->secpertrack - fs->req_sector + 1;
|
|
if (n > blk_rq_cur_sectors(fd_req))
|
|
n = blk_rq_cur_sectors(fd_req);
|
|
}
|
|
fs->scount = n;
|
|
swim3_select(fs, fs->head? READ_DATA_1: READ_DATA_0);
|
|
out_8(&sw->sector, fs->req_sector);
|
|
out_8(&sw->nsect, n);
|
|
out_8(&sw->gap3, 0);
|
|
out_le32(&dr->cmdptr, virt_to_bus(cp));
|
|
if (rq_data_dir(fd_req) == WRITE) {
|
|
/* Set up 3 dma commands: write preamble, data, postamble */
|
|
init_dma(cp, OUTPUT_MORE, write_preamble, sizeof(write_preamble));
|
|
++cp;
|
|
init_dma(cp, OUTPUT_MORE, fd_req->buffer, 512);
|
|
++cp;
|
|
init_dma(cp, OUTPUT_LAST, write_postamble, sizeof(write_postamble));
|
|
} else {
|
|
init_dma(cp, INPUT_LAST, fd_req->buffer, n * 512);
|
|
}
|
|
++cp;
|
|
out_le16(&cp->command, DBDMA_STOP);
|
|
out_8(&sw->control_bic, DO_ACTION | WRITE_SECTORS);
|
|
in_8(&sw->error);
|
|
out_8(&sw->control_bic, DO_ACTION | WRITE_SECTORS);
|
|
if (rq_data_dir(fd_req) == WRITE)
|
|
out_8(&sw->control_bis, WRITE_SECTORS);
|
|
in_8(&sw->intr);
|
|
out_le32(&dr->control, (RUN << 16) | RUN);
|
|
/* enable intr when transfer complete */
|
|
out_8(&sw->intr_enable, TRANSFER_DONE);
|
|
out_8(&sw->control_bis, DO_ACTION);
|
|
set_timeout(fs, 2*HZ, xfer_timeout); /* enable timeout */
|
|
}
|
|
|
|
static void act(struct floppy_state *fs)
|
|
{
|
|
for (;;) {
|
|
switch (fs->state) {
|
|
case idle:
|
|
return; /* XXX shouldn't get here */
|
|
|
|
case locating:
|
|
if (swim3_readbit(fs, TRACK_ZERO)) {
|
|
fs->cur_cyl = 0;
|
|
if (fs->req_cyl == 0)
|
|
fs->state = do_transfer;
|
|
else
|
|
fs->state = seeking;
|
|
break;
|
|
}
|
|
scan_track(fs);
|
|
return;
|
|
|
|
case seeking:
|
|
if (fs->cur_cyl < 0) {
|
|
fs->expect_cyl = -1;
|
|
fs->state = locating;
|
|
break;
|
|
}
|
|
if (fs->req_cyl == fs->cur_cyl) {
|
|
printk("whoops, seeking 0\n");
|
|
fs->state = do_transfer;
|
|
break;
|
|
}
|
|
seek_track(fs, fs->req_cyl - fs->cur_cyl);
|
|
return;
|
|
|
|
case settling:
|
|
/* check for SEEK_COMPLETE after 30ms */
|
|
fs->settle_time = (HZ + 32) / 33;
|
|
set_timeout(fs, fs->settle_time, settle_timeout);
|
|
return;
|
|
|
|
case do_transfer:
|
|
if (fs->cur_cyl != fs->req_cyl) {
|
|
if (fs->retries > 5) {
|
|
swim3_end_request_cur(-EIO);
|
|
fs->state = idle;
|
|
return;
|
|
}
|
|
fs->state = seeking;
|
|
break;
|
|
}
|
|
setup_transfer(fs);
|
|
return;
|
|
|
|
case jogging:
|
|
seek_track(fs, -5);
|
|
return;
|
|
|
|
default:
|
|
printk(KERN_ERR"swim3: unknown state %d\n", fs->state);
|
|
return;
|
|
}
|
|
}
|
|
}
|
|
|
|
static void scan_timeout(unsigned long data)
|
|
{
|
|
struct floppy_state *fs = (struct floppy_state *) data;
|
|
struct swim3 __iomem *sw = fs->swim3;
|
|
|
|
fs->timeout_pending = 0;
|
|
out_8(&sw->control_bic, DO_ACTION | WRITE_SECTORS);
|
|
out_8(&sw->select, RELAX);
|
|
out_8(&sw->intr_enable, 0);
|
|
fs->cur_cyl = -1;
|
|
if (fs->retries > 5) {
|
|
swim3_end_request_cur(-EIO);
|
|
fs->state = idle;
|
|
start_request(fs);
|
|
} else {
|
|
fs->state = jogging;
|
|
act(fs);
|
|
}
|
|
}
|
|
|
|
static void seek_timeout(unsigned long data)
|
|
{
|
|
struct floppy_state *fs = (struct floppy_state *) data;
|
|
struct swim3 __iomem *sw = fs->swim3;
|
|
|
|
fs->timeout_pending = 0;
|
|
out_8(&sw->control_bic, DO_SEEK);
|
|
out_8(&sw->select, RELAX);
|
|
out_8(&sw->intr_enable, 0);
|
|
printk(KERN_ERR "swim3: seek timeout\n");
|
|
swim3_end_request_cur(-EIO);
|
|
fs->state = idle;
|
|
start_request(fs);
|
|
}
|
|
|
|
static void settle_timeout(unsigned long data)
|
|
{
|
|
struct floppy_state *fs = (struct floppy_state *) data;
|
|
struct swim3 __iomem *sw = fs->swim3;
|
|
|
|
fs->timeout_pending = 0;
|
|
if (swim3_readbit(fs, SEEK_COMPLETE)) {
|
|
out_8(&sw->select, RELAX);
|
|
fs->state = locating;
|
|
act(fs);
|
|
return;
|
|
}
|
|
out_8(&sw->select, RELAX);
|
|
if (fs->settle_time < 2*HZ) {
|
|
++fs->settle_time;
|
|
set_timeout(fs, 1, settle_timeout);
|
|
return;
|
|
}
|
|
printk(KERN_ERR "swim3: seek settle timeout\n");
|
|
swim3_end_request_cur(-EIO);
|
|
fs->state = idle;
|
|
start_request(fs);
|
|
}
|
|
|
|
static void xfer_timeout(unsigned long data)
|
|
{
|
|
struct floppy_state *fs = (struct floppy_state *) data;
|
|
struct swim3 __iomem *sw = fs->swim3;
|
|
struct dbdma_regs __iomem *dr = fs->dma;
|
|
int n;
|
|
|
|
fs->timeout_pending = 0;
|
|
out_le32(&dr->control, RUN << 16);
|
|
/* We must wait a bit for dbdma to stop */
|
|
for (n = 0; (in_le32(&dr->status) & ACTIVE) && n < 1000; n++)
|
|
udelay(1);
|
|
out_8(&sw->intr_enable, 0);
|
|
out_8(&sw->control_bic, WRITE_SECTORS | DO_ACTION);
|
|
out_8(&sw->select, RELAX);
|
|
printk(KERN_ERR "swim3: timeout %sing sector %ld\n",
|
|
(rq_data_dir(fd_req)==WRITE? "writ": "read"),
|
|
(long)blk_rq_pos(fd_req));
|
|
swim3_end_request_cur(-EIO);
|
|
fs->state = idle;
|
|
start_request(fs);
|
|
}
|
|
|
|
static irqreturn_t swim3_interrupt(int irq, void *dev_id)
|
|
{
|
|
struct floppy_state *fs = (struct floppy_state *) dev_id;
|
|
struct swim3 __iomem *sw = fs->swim3;
|
|
int intr, err, n;
|
|
int stat, resid;
|
|
struct dbdma_regs __iomem *dr;
|
|
struct dbdma_cmd *cp;
|
|
|
|
intr = in_8(&sw->intr);
|
|
err = (intr & ERROR_INTR)? in_8(&sw->error): 0;
|
|
if ((intr & ERROR_INTR) && fs->state != do_transfer)
|
|
printk(KERN_ERR "swim3_interrupt, state=%d, dir=%x, intr=%x, err=%x\n",
|
|
fs->state, rq_data_dir(fd_req), intr, err);
|
|
switch (fs->state) {
|
|
case locating:
|
|
if (intr & SEEN_SECTOR) {
|
|
out_8(&sw->control_bic, DO_ACTION | WRITE_SECTORS);
|
|
out_8(&sw->select, RELAX);
|
|
out_8(&sw->intr_enable, 0);
|
|
del_timer(&fs->timeout);
|
|
fs->timeout_pending = 0;
|
|
if (sw->ctrack == 0xff) {
|
|
printk(KERN_ERR "swim3: seen sector but cyl=ff?\n");
|
|
fs->cur_cyl = -1;
|
|
if (fs->retries > 5) {
|
|
swim3_end_request_cur(-EIO);
|
|
fs->state = idle;
|
|
start_request(fs);
|
|
} else {
|
|
fs->state = jogging;
|
|
act(fs);
|
|
}
|
|
break;
|
|
}
|
|
fs->cur_cyl = sw->ctrack;
|
|
fs->cur_sector = sw->csect;
|
|
if (fs->expect_cyl != -1 && fs->expect_cyl != fs->cur_cyl)
|
|
printk(KERN_ERR "swim3: expected cyl %d, got %d\n",
|
|
fs->expect_cyl, fs->cur_cyl);
|
|
fs->state = do_transfer;
|
|
act(fs);
|
|
}
|
|
break;
|
|
case seeking:
|
|
case jogging:
|
|
if (sw->nseek == 0) {
|
|
out_8(&sw->control_bic, DO_SEEK);
|
|
out_8(&sw->select, RELAX);
|
|
out_8(&sw->intr_enable, 0);
|
|
del_timer(&fs->timeout);
|
|
fs->timeout_pending = 0;
|
|
if (fs->state == seeking)
|
|
++fs->retries;
|
|
fs->state = settling;
|
|
act(fs);
|
|
}
|
|
break;
|
|
case settling:
|
|
out_8(&sw->intr_enable, 0);
|
|
del_timer(&fs->timeout);
|
|
fs->timeout_pending = 0;
|
|
act(fs);
|
|
break;
|
|
case do_transfer:
|
|
if ((intr & (ERROR_INTR | TRANSFER_DONE)) == 0)
|
|
break;
|
|
out_8(&sw->intr_enable, 0);
|
|
out_8(&sw->control_bic, WRITE_SECTORS | DO_ACTION);
|
|
out_8(&sw->select, RELAX);
|
|
del_timer(&fs->timeout);
|
|
fs->timeout_pending = 0;
|
|
dr = fs->dma;
|
|
cp = fs->dma_cmd;
|
|
if (rq_data_dir(fd_req) == WRITE)
|
|
++cp;
|
|
/*
|
|
* Check that the main data transfer has finished.
|
|
* On writing, the swim3 sometimes doesn't use
|
|
* up all the bytes of the postamble, so we can still
|
|
* see DMA active here. That doesn't matter as long
|
|
* as all the sector data has been transferred.
|
|
*/
|
|
if ((intr & ERROR_INTR) == 0 && cp->xfer_status == 0) {
|
|
/* wait a little while for DMA to complete */
|
|
for (n = 0; n < 100; ++n) {
|
|
if (cp->xfer_status != 0)
|
|
break;
|
|
udelay(1);
|
|
barrier();
|
|
}
|
|
}
|
|
/* turn off DMA */
|
|
out_le32(&dr->control, (RUN | PAUSE) << 16);
|
|
stat = ld_le16(&cp->xfer_status);
|
|
resid = ld_le16(&cp->res_count);
|
|
if (intr & ERROR_INTR) {
|
|
n = fs->scount - 1 - resid / 512;
|
|
if (n > 0) {
|
|
blk_update_request(fd_req, 0, n << 9);
|
|
fs->req_sector += n;
|
|
}
|
|
if (fs->retries < 5) {
|
|
++fs->retries;
|
|
act(fs);
|
|
} else {
|
|
printk("swim3: error %sing block %ld (err=%x)\n",
|
|
rq_data_dir(fd_req) == WRITE? "writ": "read",
|
|
(long)blk_rq_pos(fd_req), err);
|
|
swim3_end_request_cur(-EIO);
|
|
fs->state = idle;
|
|
}
|
|
} else {
|
|
if ((stat & ACTIVE) == 0 || resid != 0) {
|
|
/* musta been an error */
|
|
printk(KERN_ERR "swim3: fd dma: stat=%x resid=%d\n", stat, resid);
|
|
printk(KERN_ERR " state=%d, dir=%x, intr=%x, err=%x\n",
|
|
fs->state, rq_data_dir(fd_req), intr, err);
|
|
swim3_end_request_cur(-EIO);
|
|
fs->state = idle;
|
|
start_request(fs);
|
|
break;
|
|
}
|
|
if (swim3_end_request(0, fs->scount << 9)) {
|
|
fs->req_sector += fs->scount;
|
|
if (fs->req_sector > fs->secpertrack) {
|
|
fs->req_sector -= fs->secpertrack;
|
|
if (++fs->head > 1) {
|
|
fs->head = 0;
|
|
++fs->req_cyl;
|
|
}
|
|
}
|
|
act(fs);
|
|
} else
|
|
fs->state = idle;
|
|
}
|
|
if (fs->state == idle)
|
|
start_request(fs);
|
|
break;
|
|
default:
|
|
printk(KERN_ERR "swim3: don't know what to do in state %d\n", fs->state);
|
|
}
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
/*
|
|
static void fd_dma_interrupt(int irq, void *dev_id)
|
|
{
|
|
}
|
|
*/
|
|
|
|
static int grab_drive(struct floppy_state *fs, enum swim_state state,
|
|
int interruptible)
|
|
{
|
|
unsigned long flags;
|
|
|
|
spin_lock_irqsave(&fs->lock, flags);
|
|
if (fs->state != idle) {
|
|
++fs->wanted;
|
|
while (fs->state != available) {
|
|
if (interruptible && signal_pending(current)) {
|
|
--fs->wanted;
|
|
spin_unlock_irqrestore(&fs->lock, flags);
|
|
return -EINTR;
|
|
}
|
|
interruptible_sleep_on(&fs->wait);
|
|
}
|
|
--fs->wanted;
|
|
}
|
|
fs->state = state;
|
|
spin_unlock_irqrestore(&fs->lock, flags);
|
|
return 0;
|
|
}
|
|
|
|
static void release_drive(struct floppy_state *fs)
|
|
{
|
|
unsigned long flags;
|
|
|
|
spin_lock_irqsave(&fs->lock, flags);
|
|
fs->state = idle;
|
|
start_request(fs);
|
|
spin_unlock_irqrestore(&fs->lock, flags);
|
|
}
|
|
|
|
static int fd_eject(struct floppy_state *fs)
|
|
{
|
|
int err, n;
|
|
|
|
err = grab_drive(fs, ejecting, 1);
|
|
if (err)
|
|
return err;
|
|
swim3_action(fs, EJECT);
|
|
for (n = 20; n > 0; --n) {
|
|
if (signal_pending(current)) {
|
|
err = -EINTR;
|
|
break;
|
|
}
|
|
swim3_select(fs, RELAX);
|
|
schedule_timeout_interruptible(1);
|
|
if (swim3_readbit(fs, DISK_IN) == 0)
|
|
break;
|
|
}
|
|
swim3_select(fs, RELAX);
|
|
udelay(150);
|
|
fs->ejected = 1;
|
|
release_drive(fs);
|
|
return err;
|
|
}
|
|
|
|
static struct floppy_struct floppy_type =
|
|
{ 2880,18,2,80,0,0x1B,0x00,0xCF,0x6C,NULL }; /* 7 1.44MB 3.5" */
|
|
|
|
static int floppy_locked_ioctl(struct block_device *bdev, fmode_t mode,
|
|
unsigned int cmd, unsigned long param)
|
|
{
|
|
struct floppy_state *fs = bdev->bd_disk->private_data;
|
|
int err;
|
|
|
|
if ((cmd & 0x80) && !capable(CAP_SYS_ADMIN))
|
|
return -EPERM;
|
|
|
|
if (fs->mdev->media_bay &&
|
|
check_media_bay(fs->mdev->media_bay) != MB_FD)
|
|
return -ENXIO;
|
|
|
|
switch (cmd) {
|
|
case FDEJECT:
|
|
if (fs->ref_count != 1)
|
|
return -EBUSY;
|
|
err = fd_eject(fs);
|
|
return err;
|
|
case FDGETPRM:
|
|
if (copy_to_user((void __user *) param, &floppy_type,
|
|
sizeof(struct floppy_struct)))
|
|
return -EFAULT;
|
|
return 0;
|
|
}
|
|
return -ENOTTY;
|
|
}
|
|
|
|
static int floppy_ioctl(struct block_device *bdev, fmode_t mode,
|
|
unsigned int cmd, unsigned long param)
|
|
{
|
|
int ret;
|
|
|
|
mutex_lock(&swim3_mutex);
|
|
ret = floppy_locked_ioctl(bdev, mode, cmd, param);
|
|
mutex_unlock(&swim3_mutex);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int floppy_open(struct block_device *bdev, fmode_t mode)
|
|
{
|
|
struct floppy_state *fs = bdev->bd_disk->private_data;
|
|
struct swim3 __iomem *sw = fs->swim3;
|
|
int n, err = 0;
|
|
|
|
if (fs->ref_count == 0) {
|
|
if (fs->mdev->media_bay &&
|
|
check_media_bay(fs->mdev->media_bay) != MB_FD)
|
|
return -ENXIO;
|
|
out_8(&sw->setup, S_IBM_DRIVE | S_FCLK_DIV2);
|
|
out_8(&sw->control_bic, 0xff);
|
|
out_8(&sw->mode, 0x95);
|
|
udelay(10);
|
|
out_8(&sw->intr_enable, 0);
|
|
out_8(&sw->control_bis, DRIVE_ENABLE | INTR_ENABLE);
|
|
swim3_action(fs, MOTOR_ON);
|
|
fs->write_prot = -1;
|
|
fs->cur_cyl = -1;
|
|
for (n = 0; n < 2 * HZ; ++n) {
|
|
if (n >= HZ/30 && swim3_readbit(fs, SEEK_COMPLETE))
|
|
break;
|
|
if (signal_pending(current)) {
|
|
err = -EINTR;
|
|
break;
|
|
}
|
|
swim3_select(fs, RELAX);
|
|
schedule_timeout_interruptible(1);
|
|
}
|
|
if (err == 0 && (swim3_readbit(fs, SEEK_COMPLETE) == 0
|
|
|| swim3_readbit(fs, DISK_IN) == 0))
|
|
err = -ENXIO;
|
|
swim3_action(fs, SETMFM);
|
|
swim3_select(fs, RELAX);
|
|
|
|
} else if (fs->ref_count == -1 || mode & FMODE_EXCL)
|
|
return -EBUSY;
|
|
|
|
if (err == 0 && (mode & FMODE_NDELAY) == 0
|
|
&& (mode & (FMODE_READ|FMODE_WRITE))) {
|
|
check_disk_change(bdev);
|
|
if (fs->ejected)
|
|
err = -ENXIO;
|
|
}
|
|
|
|
if (err == 0 && (mode & FMODE_WRITE)) {
|
|
if (fs->write_prot < 0)
|
|
fs->write_prot = swim3_readbit(fs, WRITE_PROT);
|
|
if (fs->write_prot)
|
|
err = -EROFS;
|
|
}
|
|
|
|
if (err) {
|
|
if (fs->ref_count == 0) {
|
|
swim3_action(fs, MOTOR_OFF);
|
|
out_8(&sw->control_bic, DRIVE_ENABLE | INTR_ENABLE);
|
|
swim3_select(fs, RELAX);
|
|
}
|
|
return err;
|
|
}
|
|
|
|
if (mode & FMODE_EXCL)
|
|
fs->ref_count = -1;
|
|
else
|
|
++fs->ref_count;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int floppy_unlocked_open(struct block_device *bdev, fmode_t mode)
|
|
{
|
|
int ret;
|
|
|
|
mutex_lock(&swim3_mutex);
|
|
ret = floppy_open(bdev, mode);
|
|
mutex_unlock(&swim3_mutex);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int floppy_release(struct gendisk *disk, fmode_t mode)
|
|
{
|
|
struct floppy_state *fs = disk->private_data;
|
|
struct swim3 __iomem *sw = fs->swim3;
|
|
mutex_lock(&swim3_mutex);
|
|
if (fs->ref_count > 0 && --fs->ref_count == 0) {
|
|
swim3_action(fs, MOTOR_OFF);
|
|
out_8(&sw->control_bic, 0xff);
|
|
swim3_select(fs, RELAX);
|
|
}
|
|
mutex_unlock(&swim3_mutex);
|
|
return 0;
|
|
}
|
|
|
|
static unsigned int floppy_check_events(struct gendisk *disk,
|
|
unsigned int clearing)
|
|
{
|
|
struct floppy_state *fs = disk->private_data;
|
|
return fs->ejected ? DISK_EVENT_MEDIA_CHANGE : 0;
|
|
}
|
|
|
|
static int floppy_revalidate(struct gendisk *disk)
|
|
{
|
|
struct floppy_state *fs = disk->private_data;
|
|
struct swim3 __iomem *sw;
|
|
int ret, n;
|
|
|
|
if (fs->mdev->media_bay &&
|
|
check_media_bay(fs->mdev->media_bay) != MB_FD)
|
|
return -ENXIO;
|
|
|
|
sw = fs->swim3;
|
|
grab_drive(fs, revalidating, 0);
|
|
out_8(&sw->intr_enable, 0);
|
|
out_8(&sw->control_bis, DRIVE_ENABLE);
|
|
swim3_action(fs, MOTOR_ON); /* necessary? */
|
|
fs->write_prot = -1;
|
|
fs->cur_cyl = -1;
|
|
mdelay(1);
|
|
for (n = HZ; n > 0; --n) {
|
|
if (swim3_readbit(fs, SEEK_COMPLETE))
|
|
break;
|
|
if (signal_pending(current))
|
|
break;
|
|
swim3_select(fs, RELAX);
|
|
schedule_timeout_interruptible(1);
|
|
}
|
|
ret = swim3_readbit(fs, SEEK_COMPLETE) == 0
|
|
|| swim3_readbit(fs, DISK_IN) == 0;
|
|
if (ret)
|
|
swim3_action(fs, MOTOR_OFF);
|
|
else {
|
|
fs->ejected = 0;
|
|
swim3_action(fs, SETMFM);
|
|
}
|
|
swim3_select(fs, RELAX);
|
|
|
|
release_drive(fs);
|
|
return ret;
|
|
}
|
|
|
|
static const struct block_device_operations floppy_fops = {
|
|
.open = floppy_unlocked_open,
|
|
.release = floppy_release,
|
|
.ioctl = floppy_ioctl,
|
|
.check_events = floppy_check_events,
|
|
.revalidate_disk= floppy_revalidate,
|
|
};
|
|
|
|
static int swim3_add_device(struct macio_dev *mdev, int index)
|
|
{
|
|
struct device_node *swim = mdev->ofdev.dev.of_node;
|
|
struct floppy_state *fs = &floppy_states[index];
|
|
int rc = -EBUSY;
|
|
|
|
/* Check & Request resources */
|
|
if (macio_resource_count(mdev) < 2) {
|
|
printk(KERN_WARNING "ifd%d: no address for %s\n",
|
|
index, swim->full_name);
|
|
return -ENXIO;
|
|
}
|
|
if (macio_irq_count(mdev) < 2) {
|
|
printk(KERN_WARNING "fd%d: no intrs for device %s\n",
|
|
index, swim->full_name);
|
|
}
|
|
if (macio_request_resource(mdev, 0, "swim3 (mmio)")) {
|
|
printk(KERN_ERR "fd%d: can't request mmio resource for %s\n",
|
|
index, swim->full_name);
|
|
return -EBUSY;
|
|
}
|
|
if (macio_request_resource(mdev, 1, "swim3 (dma)")) {
|
|
printk(KERN_ERR "fd%d: can't request dma resource for %s\n",
|
|
index, swim->full_name);
|
|
macio_release_resource(mdev, 0);
|
|
return -EBUSY;
|
|
}
|
|
dev_set_drvdata(&mdev->ofdev.dev, fs);
|
|
|
|
if (mdev->media_bay == NULL)
|
|
pmac_call_feature(PMAC_FTR_SWIM3_ENABLE, swim, 0, 1);
|
|
|
|
memset(fs, 0, sizeof(*fs));
|
|
spin_lock_init(&fs->lock);
|
|
fs->state = idle;
|
|
fs->swim3 = (struct swim3 __iomem *)
|
|
ioremap(macio_resource_start(mdev, 0), 0x200);
|
|
if (fs->swim3 == NULL) {
|
|
printk("fd%d: couldn't map registers for %s\n",
|
|
index, swim->full_name);
|
|
rc = -ENOMEM;
|
|
goto out_release;
|
|
}
|
|
fs->dma = (struct dbdma_regs __iomem *)
|
|
ioremap(macio_resource_start(mdev, 1), 0x200);
|
|
if (fs->dma == NULL) {
|
|
printk("fd%d: couldn't map DMA for %s\n",
|
|
index, swim->full_name);
|
|
iounmap(fs->swim3);
|
|
rc = -ENOMEM;
|
|
goto out_release;
|
|
}
|
|
fs->swim3_intr = macio_irq(mdev, 0);
|
|
fs->dma_intr = macio_irq(mdev, 1);
|
|
fs->cur_cyl = -1;
|
|
fs->cur_sector = -1;
|
|
fs->secpercyl = 36;
|
|
fs->secpertrack = 18;
|
|
fs->total_secs = 2880;
|
|
fs->mdev = mdev;
|
|
init_waitqueue_head(&fs->wait);
|
|
|
|
fs->dma_cmd = (struct dbdma_cmd *) DBDMA_ALIGN(fs->dbdma_cmd_space);
|
|
memset(fs->dma_cmd, 0, 2 * sizeof(struct dbdma_cmd));
|
|
st_le16(&fs->dma_cmd[1].command, DBDMA_STOP);
|
|
|
|
if (request_irq(fs->swim3_intr, swim3_interrupt, 0, "SWIM3", fs)) {
|
|
printk(KERN_ERR "fd%d: couldn't request irq %d for %s\n",
|
|
index, fs->swim3_intr, swim->full_name);
|
|
pmac_call_feature(PMAC_FTR_SWIM3_ENABLE, swim, 0, 0);
|
|
goto out_unmap;
|
|
return -EBUSY;
|
|
}
|
|
/*
|
|
if (request_irq(fs->dma_intr, fd_dma_interrupt, 0, "SWIM3-dma", fs)) {
|
|
printk(KERN_ERR "Couldn't get irq %d for SWIM3 DMA",
|
|
fs->dma_intr);
|
|
return -EBUSY;
|
|
}
|
|
*/
|
|
|
|
init_timer(&fs->timeout);
|
|
|
|
printk(KERN_INFO "fd%d: SWIM3 floppy controller %s\n", floppy_count,
|
|
mdev->media_bay ? "in media bay" : "");
|
|
|
|
return 0;
|
|
|
|
out_unmap:
|
|
iounmap(fs->dma);
|
|
iounmap(fs->swim3);
|
|
|
|
out_release:
|
|
macio_release_resource(mdev, 0);
|
|
macio_release_resource(mdev, 1);
|
|
|
|
return rc;
|
|
}
|
|
|
|
static int __devinit swim3_attach(struct macio_dev *mdev, const struct of_device_id *match)
|
|
{
|
|
int i, rc;
|
|
struct gendisk *disk;
|
|
|
|
/* Add the drive */
|
|
rc = swim3_add_device(mdev, floppy_count);
|
|
if (rc)
|
|
return rc;
|
|
|
|
/* Now create the queue if not there yet */
|
|
if (swim3_queue == NULL) {
|
|
/* If we failed, there isn't much we can do as the driver is still
|
|
* too dumb to remove the device, just bail out
|
|
*/
|
|
if (register_blkdev(FLOPPY_MAJOR, "fd"))
|
|
return 0;
|
|
swim3_queue = blk_init_queue(do_fd_request, &swim3_lock);
|
|
if (swim3_queue == NULL) {
|
|
unregister_blkdev(FLOPPY_MAJOR, "fd");
|
|
return 0;
|
|
}
|
|
}
|
|
|
|
/* Now register that disk. Same comment about failure handling */
|
|
i = floppy_count++;
|
|
disk = disks[i] = alloc_disk(1);
|
|
if (disk == NULL)
|
|
return 0;
|
|
|
|
disk->major = FLOPPY_MAJOR;
|
|
disk->first_minor = i;
|
|
disk->fops = &floppy_fops;
|
|
disk->private_data = &floppy_states[i];
|
|
disk->queue = swim3_queue;
|
|
disk->flags |= GENHD_FL_REMOVABLE;
|
|
sprintf(disk->disk_name, "fd%d", i);
|
|
set_capacity(disk, 2880);
|
|
add_disk(disk);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static struct of_device_id swim3_match[] =
|
|
{
|
|
{
|
|
.name = "swim3",
|
|
},
|
|
{
|
|
.compatible = "ohare-swim3"
|
|
},
|
|
{
|
|
.compatible = "swim3"
|
|
},
|
|
};
|
|
|
|
static struct macio_driver swim3_driver =
|
|
{
|
|
.driver = {
|
|
.name = "swim3",
|
|
.of_match_table = swim3_match,
|
|
},
|
|
.probe = swim3_attach,
|
|
#if 0
|
|
.suspend = swim3_suspend,
|
|
.resume = swim3_resume,
|
|
#endif
|
|
};
|
|
|
|
|
|
int swim3_init(void)
|
|
{
|
|
macio_register_driver(&swim3_driver);
|
|
return 0;
|
|
}
|
|
|
|
module_init(swim3_init)
|
|
|
|
MODULE_LICENSE("GPL");
|
|
MODULE_AUTHOR("Paul Mackerras");
|
|
MODULE_ALIAS_BLOCKDEV_MAJOR(FLOPPY_MAJOR);
|