korg/linux
0
0
Fork 0
mirror of https://mirrors.bfsu.edu.cn/git/linux.git synced 2024-11-18 01:34:14 +08:00
Code Issues Packages Projects Releases Wiki Activity
93bcf12e71
linux/drivers/usb/gadget/pxa27x_udc.h
Robert Jarzmik 367815eea4 USB: pxa27x_udc: single-thread setup requests 
Since the PXA 27x UDC automatically ACK's some control
packets such as SET_INTERFACE, the gadgets may not get a
chance to process the request before another control packet
is received. The Linux gadgets do not expect to receive
setup callbacks out of order. The file storage gadget only
saves the "highest" priority request.

The PXA27x UDC driver must make sure it only sends one up at
a time, allowing the gadget to make changes before
continuing. In theory, the host would be NACK'd while the
gadget processes the change but the UDC has already ACK'd
the request. If another request is sent by the host that is
not automatically ACK'd by the UDC, then the throttling
happens properly to regain sync.

The observed case was the file_storage gadget timing out on
a BulkReset request because the SET_INTERFACE was being
processed by the gadget. Since SET_INTERFACE is higher
priority than BulkReset, the BulkReset was dropped.  This
was exacerbated by turning on the debug which delayed the
fsg signal processing thread.

This also fixes the "should never get in
WAIT_ACK_SET_CONF_INTERF state here!!!" warning.

Reported-by: Vernon Sauder <vernoninhand@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

index 51790b0..1937d8c 100644
2009-06-15 21:44:42 -07:00

500 lines
19 KiB
C
Raw Blame History

/*
* linux/drivers/usb/gadget/pxa27x_udc.h
* Intel PXA27x on-chip full speed USB device controller
*
* Inspired by original driver by Frank Becker, David Brownell, and others.
* Copyright (C) 2008 Robert Jarzmik
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#ifndef __LINUX_USB_GADGET_PXA27X_H
#define __LINUX_USB_GADGET_PXA27X_H
#include <linux/types.h>
#include <linux/spinlock.h>
#include <linux/io.h>
#include <linux/usb/otg.h>
/*
* Register definitions
*/
/* Offsets */
#define UDCCR 0x0000 /* UDC Control Register */
#define UDCICR0 0x0004 /* UDC Interrupt Control Register0 */
#define UDCICR1 0x0008 /* UDC Interrupt Control Register1 */
#define UDCISR0 0x000C /* UDC Interrupt Status Register 0 */
#define UDCISR1 0x0010 /* UDC Interrupt Status Register 1 */
#define UDCFNR 0x0014 /* UDC Frame Number Register */
#define UDCOTGICR 0x0018 /* UDC On-The-Go interrupt control */
#define UP2OCR 0x0020 /* USB Port 2 Output Control register */
#define UP3OCR 0x0024 /* USB Port 3 Output Control register */
#define UDCCSRn(x) (0x0100 + ((x)<<2)) /* UDC Control/Status register */
#define UDCBCRn(x) (0x0200 + ((x)<<2)) /* UDC Byte Count Register */
#define UDCDRn(x) (0x0300 + ((x)<<2)) /* UDC Data Register */
#define UDCCRn(x) (0x0400 + ((x)<<2)) /* UDC Control Register */
#define UDCCR_OEN (1 << 31) /* On-the-Go Enable */
#define UDCCR_AALTHNP (1 << 30) /* A-device Alternate Host Negotiation
Protocol Port Support */
#define UDCCR_AHNP (1 << 29) /* A-device Host Negotiation Protocol
Support */
#define UDCCR_BHNP (1 << 28) /* B-device Host Negotiation Protocol
Enable */
#define UDCCR_DWRE (1 << 16) /* Device Remote Wake-up Enable */
#define UDCCR_ACN (0x03 << 11) /* Active UDC configuration Number */
#define UDCCR_ACN_S 11
#define UDCCR_AIN (0x07 << 8) /* Active UDC interface Number */
#define UDCCR_AIN_S 8
#define UDCCR_AAISN (0x07 << 5) /* Active UDC Alternate Interface
Setting Number */
#define UDCCR_AAISN_S 5
#define UDCCR_SMAC (1 << 4) /* Switch Endpoint Memory to Active
Configuration */
#define UDCCR_EMCE (1 << 3) /* Endpoint Memory Configuration
Error */
#define UDCCR_UDR (1 << 2) /* UDC Resume */
#define UDCCR_UDA (1 << 1) /* UDC Active */
#define UDCCR_UDE (1 << 0) /* UDC Enable */
#define UDCICR_INT(n, intr) (((intr) & 0x03) << (((n) & 0x0F) * 2))
#define UDCICR1_IECC (1 << 31) /* IntEn - Configuration Change */
#define UDCICR1_IESOF (1 << 30) /* IntEn - Start of Frame */
#define UDCICR1_IERU (1 << 29) /* IntEn - Resume */
#define UDCICR1_IESU (1 << 28) /* IntEn - Suspend */
#define UDCICR1_IERS (1 << 27) /* IntEn - Reset */
#define UDCICR_FIFOERR (1 << 1) /* FIFO Error interrupt for EP */
#define UDCICR_PKTCOMPL (1 << 0) /* Packet Complete interrupt for EP */
#define UDCICR_INT_MASK (UDCICR_FIFOERR | UDCICR_PKTCOMPL)
#define UDCISR_INT(n, intr) (((intr) & 0x03) << (((n) & 0x0F) * 2))
#define UDCISR1_IRCC (1 << 31) /* IntReq - Configuration Change */
#define UDCISR1_IRSOF (1 << 30) /* IntReq - Start of Frame */
#define UDCISR1_IRRU (1 << 29) /* IntReq - Resume */
#define UDCISR1_IRSU (1 << 28) /* IntReq - Suspend */
#define UDCISR1_IRRS (1 << 27) /* IntReq - Reset */
#define UDCISR_INT_MASK (UDCICR_FIFOERR | UDCICR_PKTCOMPL)
#define UDCOTGICR_IESF (1 << 24) /* OTG SET_FEATURE command recvd */
#define UDCOTGICR_IEXR (1 << 17) /* Extra Transciever Interrupt
Rising Edge Interrupt Enable */
#define UDCOTGICR_IEXF (1 << 16) /* Extra Transciever Interrupt
Falling Edge Interrupt Enable */
#define UDCOTGICR_IEVV40R (1 << 9) /* OTG Vbus Valid 4.0V Rising Edge
Interrupt Enable */
#define UDCOTGICR_IEVV40F (1 << 8) /* OTG Vbus Valid 4.0V Falling Edge
Interrupt Enable */
#define UDCOTGICR_IEVV44R (1 << 7) /* OTG Vbus Valid 4.4V Rising Edge
Interrupt Enable */
#define UDCOTGICR_IEVV44F (1 << 6) /* OTG Vbus Valid 4.4V Falling Edge
Interrupt Enable */
#define UDCOTGICR_IESVR (1 << 5) /* OTG Session Valid Rising Edge
Interrupt Enable */
#define UDCOTGICR_IESVF (1 << 4) /* OTG Session Valid Falling Edge
Interrupt Enable */
#define UDCOTGICR_IESDR (1 << 3) /* OTG A-Device SRP Detect Rising
Edge Interrupt Enable */
#define UDCOTGICR_IESDF (1 << 2) /* OTG A-Device SRP Detect Falling
Edge Interrupt Enable */
#define UDCOTGICR_IEIDR (1 << 1) /* OTG ID Change Rising Edge
Interrupt Enable */
#define UDCOTGICR_IEIDF (1 << 0) /* OTG ID Change Falling Edge
Interrupt Enable */
/* Host Port 2 field bits */
#define UP2OCR_CPVEN (1 << 0) /* Charge Pump Vbus Enable */
#define UP2OCR_CPVPE (1 << 1) /* Charge Pump Vbus Pulse Enable */
/* Transceiver enablers */
#define UP2OCR_DPPDE (1 << 2) /* D+ Pull Down Enable */
#define UP2OCR_DMPDE (1 << 3) /* D- Pull Down Enable */
#define UP2OCR_DPPUE (1 << 4) /* D+ Pull Up Enable */
#define UP2OCR_DMPUE (1 << 5) /* D- Pull Up Enable */
#define UP2OCR_DPPUBE (1 << 6) /* D+ Pull Up Bypass Enable */
#define UP2OCR_DMPUBE (1 << 7) /* D- Pull Up Bypass Enable */
#define UP2OCR_EXSP (1 << 8) /* External Transceiver Speed Control */
#define UP2OCR_EXSUS (1 << 9) /* External Transceiver Speed Enable */
#define UP2OCR_IDON (1 << 10) /* OTG ID Read Enable */
#define UP2OCR_HXS (1 << 16) /* Transceiver Output Select */
#define UP2OCR_HXOE (1 << 17) /* Transceiver Output Enable */
#define UP2OCR_SEOS (1 << 24) /* Single-Ended Output Select */
#define UDCCSR0_ACM (1 << 9) /* Ack Control Mode */
#define UDCCSR0_AREN (1 << 8) /* Ack Response Enable */
#define UDCCSR0_SA (1 << 7) /* Setup Active */
#define UDCCSR0_RNE (1 << 6) /* Receive FIFO Not Empty */
#define UDCCSR0_FST (1 << 5) /* Force Stall */
#define UDCCSR0_SST (1 << 4) /* Sent Stall */
#define UDCCSR0_DME (1 << 3) /* DMA Enable */
#define UDCCSR0_FTF (1 << 2) /* Flush Transmit FIFO */
#define UDCCSR0_IPR (1 << 1) /* IN Packet Ready */
#define UDCCSR0_OPC (1 << 0) /* OUT Packet Complete */
#define UDCCSR_DPE (1 << 9) /* Data Packet Error */
#define UDCCSR_FEF (1 << 8) /* Flush Endpoint FIFO */
#define UDCCSR_SP (1 << 7) /* Short Packet Control/Status */
#define UDCCSR_BNE (1 << 6) /* Buffer Not Empty (IN endpoints) */
#define UDCCSR_BNF (1 << 6) /* Buffer Not Full (OUT endpoints) */
#define UDCCSR_FST (1 << 5) /* Force STALL */
#define UDCCSR_SST (1 << 4) /* Sent STALL */
#define UDCCSR_DME (1 << 3) /* DMA Enable */
#define UDCCSR_TRN (1 << 2) /* Tx/Rx NAK */
#define UDCCSR_PC (1 << 1) /* Packet Complete */
#define UDCCSR_FS (1 << 0) /* FIFO needs service */
#define UDCCONR_CN (0x03 << 25) /* Configuration Number */
#define UDCCONR_CN_S 25
#define UDCCONR_IN (0x07 << 22) /* Interface Number */
#define UDCCONR_IN_S 22
#define UDCCONR_AISN (0x07 << 19) /* Alternate Interface Number */
#define UDCCONR_AISN_S 19
#define UDCCONR_EN (0x0f << 15) /* Endpoint Number */
#define UDCCONR_EN_S 15
#define UDCCONR_ET (0x03 << 13) /* Endpoint Type: */
#define UDCCONR_ET_S 13
#define UDCCONR_ET_INT (0x03 << 13) /* Interrupt */
#define UDCCONR_ET_BULK (0x02 << 13) /* Bulk */
#define UDCCONR_ET_ISO (0x01 << 13) /* Isochronous */
#define UDCCONR_ET_NU (0x00 << 13) /* Not used */
#define UDCCONR_ED (1 << 12) /* Endpoint Direction */
#define UDCCONR_MPS (0x3ff << 2) /* Maximum Packet Size */
#define UDCCONR_MPS_S 2
#define UDCCONR_DE (1 << 1) /* Double Buffering Enable */
#define UDCCONR_EE (1 << 0) /* Endpoint Enable */
#define UDCCR_MASK_BITS (UDCCR_OEN | UDCCR_SMAC | UDCCR_UDR | UDCCR_UDE)
#define UDCCSR_WR_MASK (UDCCSR_DME | UDCCSR_FST)
#define UDC_FNR_MASK (0x7ff)
#define UDC_BCR_MASK (0x3ff)
/*
* UDCCR = UDC Endpoint Configuration Registers
* UDCCSR = UDC Control/Status Register for this EP
* UDCBCR = UDC Byte Count Remaining (contents of OUT fifo)
* UDCDR = UDC Endpoint Data Register (the fifo)
*/
#define ofs_UDCCR(ep) (UDCCRn(ep->idx))
#define ofs_UDCCSR(ep) (UDCCSRn(ep->idx))
#define ofs_UDCBCR(ep) (UDCBCRn(ep->idx))
#define ofs_UDCDR(ep) (UDCDRn(ep->idx))
/* Register access macros */
#define udc_ep_readl(ep, reg) \
__raw_readl((ep)->dev->regs + ofs_##reg(ep))
#define udc_ep_writel(ep, reg, value) \
__raw_writel((value), ep->dev->regs + ofs_##reg(ep))
#define udc_ep_readb(ep, reg) \
__raw_readb((ep)->dev->regs + ofs_##reg(ep))
#define udc_ep_writeb(ep, reg, value) \
__raw_writeb((value), ep->dev->regs + ofs_##reg(ep))
#define udc_readl(dev, reg) \
__raw_readl((dev)->regs + (reg))
#define udc_writel(udc, reg, value) \
__raw_writel((value), (udc)->regs + (reg))
#define UDCCSR_MASK (UDCCSR_FST | UDCCSR_DME)
#define UDCCISR0_EP_MASK ~0
#define UDCCISR1_EP_MASK 0xffff
#define UDCCSR0_CTRL_REQ_MASK (UDCCSR0_OPC | UDCCSR0_SA | UDCCSR0_RNE)
#define EPIDX(ep) (ep->idx)
#define EPADDR(ep) (ep->addr)
#define EPXFERTYPE(ep) (ep->type)
#define EPNAME(ep) (ep->name)
#define is_ep0(ep) (!ep->idx)
#define EPXFERTYPE_is_ISO(ep) (EPXFERTYPE(ep) == USB_ENDPOINT_XFER_ISOC)
/*
* Endpoint definitions
*
* Once enabled, pxa endpoint configuration is freezed, and cannot change
* unless a reset happens or the udc is disabled.
* Therefore, we must define all pxa potential endpoint definitions needed for
* all gadget and set them up before the udc is enabled.
*
* As the architecture chosen is fully static, meaning the pxa endpoint
* configurations are set up once and for all, we must provide a way to match
* one usb endpoint (usb_ep) to several pxa endpoints. The reason is that gadget
* layer autoconf doesn't choose the usb_ep endpoint on (config, interface, alt)
* criteria, while the pxa architecture requires that.
*
* The solution is to define several pxa endpoints matching one usb_ep. Ex:
* - "ep1-in" matches pxa endpoint EPA (which is an IN ep at addr 1, when
* the udc talks on (config=3, interface=0, alt=0)
* - "ep1-in" matches pxa endpoint EPB (which is an IN ep at addr 1, when
* the udc talks on (config=3, interface=0, alt=1)
* - "ep1-in" matches pxa endpoint EPC (which is an IN ep at addr 1, when
* the udc talks on (config=2, interface=0, alt=0)
*
* We'll define the pxa endpoint by its index (EPA => idx=1, EPB => idx=2, ...)
*/
/*
* Endpoint definition helpers
*/
#define USB_EP_DEF(addr, bname, dir, type, maxpkt) \
{ .usb_ep = { .name = bname, .ops = &pxa_ep_ops, .maxpacket = maxpkt, }, \
.desc = { .bEndpointAddress = addr | (dir ? USB_DIR_IN : 0), \
.bmAttributes = type, \
.wMaxPacketSize = maxpkt, }, \
.dev = &memory \
}
#define USB_EP_BULK(addr, bname, dir) \
USB_EP_DEF(addr, bname, dir, USB_ENDPOINT_XFER_BULK, BULK_FIFO_SIZE)
#define USB_EP_ISO(addr, bname, dir) \
USB_EP_DEF(addr, bname, dir, USB_ENDPOINT_XFER_ISOC, ISO_FIFO_SIZE)
#define USB_EP_INT(addr, bname, dir) \
USB_EP_DEF(addr, bname, dir, USB_ENDPOINT_XFER_INT, INT_FIFO_SIZE)
#define USB_EP_IN_BULK(n) USB_EP_BULK(n, "ep" #n "in-bulk", 1)
#define USB_EP_OUT_BULK(n) USB_EP_BULK(n, "ep" #n "out-bulk", 0)
#define USB_EP_IN_ISO(n) USB_EP_ISO(n, "ep" #n "in-iso", 1)
#define USB_EP_OUT_ISO(n) USB_EP_ISO(n, "ep" #n "out-iso", 0)
#define USB_EP_IN_INT(n) USB_EP_INT(n, "ep" #n "in-int", 1)
#define USB_EP_CTRL USB_EP_DEF(0, "ep0", 0, 0, EP0_FIFO_SIZE)
#define PXA_EP_DEF(_idx, _addr, dir, _type, maxpkt, _config, iface, altset) \
{ \
.dev = &memory, \
.name = "ep" #_idx, \
.idx = _idx, .enabled = 0, \
.dir_in = dir, .addr = _addr, \
.config = _config, .interface = iface, .alternate = altset, \
.type = _type, .fifo_size = maxpkt, \
}
#define PXA_EP_BULK(_idx, addr, dir, config, iface, alt) \
PXA_EP_DEF(_idx, addr, dir, USB_ENDPOINT_XFER_BULK, BULK_FIFO_SIZE, \
config, iface, alt)
#define PXA_EP_ISO(_idx, addr, dir, config, iface, alt) \
PXA_EP_DEF(_idx, addr, dir, USB_ENDPOINT_XFER_ISOC, ISO_FIFO_SIZE, \
config, iface, alt)
#define PXA_EP_INT(_idx, addr, dir, config, iface, alt) \
PXA_EP_DEF(_idx, addr, dir, USB_ENDPOINT_XFER_INT, INT_FIFO_SIZE, \
config, iface, alt)
#define PXA_EP_IN_BULK(i, adr, c, f, a) PXA_EP_BULK(i, adr, 1, c, f, a)
#define PXA_EP_OUT_BULK(i, adr, c, f, a) PXA_EP_BULK(i, adr, 0, c, f, a)
#define PXA_EP_IN_ISO(i, adr, c, f, a) PXA_EP_ISO(i, adr, 1, c, f, a)
#define PXA_EP_OUT_ISO(i, adr, c, f, a) PXA_EP_ISO(i, adr, 0, c, f, a)
#define PXA_EP_IN_INT(i, adr, c, f, a) PXA_EP_INT(i, adr, 1, c, f, a)
#define PXA_EP_CTRL PXA_EP_DEF(0, 0, 0, 0, EP0_FIFO_SIZE, 0, 0, 0)
struct pxa27x_udc;
struct stats {
unsigned long in_ops;
unsigned long out_ops;
unsigned long in_bytes;
unsigned long out_bytes;
unsigned long irqs;
};
/**
* struct udc_usb_ep - container of each usb_ep structure
* @usb_ep: usb endpoint
* @desc: usb descriptor, especially type and address
* @dev: udc managing this endpoint
* @pxa_ep: matching pxa_ep (cache of find_pxa_ep() call)
*/
struct udc_usb_ep {
struct usb_ep usb_ep;
struct usb_endpoint_descriptor desc;
struct pxa_udc *dev;
struct pxa_ep *pxa_ep;
};
/**
* struct pxa_ep - pxa endpoint
* @dev: udc device
* @queue: requests queue
* @lock: lock to pxa_ep data (queues and stats)
* @enabled: true when endpoint enabled (not stopped by gadget layer)
* @idx: endpoint index (1 => epA, 2 => epB, ..., 24 => epX)
* @name: endpoint name (for trace/debug purpose)
* @dir_in: 1 if IN endpoint, 0 if OUT endpoint
* @addr: usb endpoint number
* @config: configuration in which this endpoint is active
* @interface: interface in which this endpoint is active
* @alternate: altsetting in which this endpoitn is active
* @fifo_size: max packet size in the endpoint fifo
* @type: endpoint type (bulk, iso, int, ...)
* @udccsr_value: save register of UDCCSR0 for suspend/resume
* @udccr_value: save register of UDCCR for suspend/resume
* @stats: endpoint statistics
*
* The *PROBLEM* is that pxa's endpoint configuration scheme is both misdesigned
* (cares about config/interface/altsetting, thus placing needless limits on
* device capability) and full of implementation bugs forcing it to be set up
* for use more or less like a pxa255.
*
* As we define the pxa_ep statically, we must guess all needed pxa_ep for all
* gadget which may work with this udc driver.
*/
struct pxa_ep {
struct pxa_udc *dev;
struct list_head queue;
spinlock_t lock; /* Protects this structure */
/* (queues, stats) */
unsigned enabled:1;
unsigned idx:5;
char *name;
/*
* Specific pxa endpoint data, needed for hardware initialization
*/
unsigned dir_in:1;
unsigned addr:3;
unsigned config:2;
unsigned interface:3;
unsigned alternate:3;
unsigned fifo_size;
unsigned type;
#ifdef CONFIG_PM
u32 udccsr_value;
u32 udccr_value;
#endif
struct stats stats;
};
/**
* struct pxa27x_request - container of each usb_request structure
* @req: usb request
* @udc_usb_ep: usb endpoint the request was submitted on
* @in_use: sanity check if request already queued on an pxa_ep
* @queue: linked list of requests, linked on pxa_ep->queue
*/
struct pxa27x_request {
struct usb_request req;
struct udc_usb_ep *udc_usb_ep;
unsigned in_use:1;
struct list_head queue;
};
enum ep0_state {
WAIT_FOR_SETUP,
SETUP_STAGE,
IN_DATA_STAGE,
OUT_DATA_STAGE,
IN_STATUS_STAGE,
OUT_STATUS_STAGE,
STALL,
WAIT_ACK_SET_CONF_INTERF
};
static char *ep0_state_name[] = {
"WAIT_FOR_SETUP", "SETUP_STAGE", "IN_DATA_STAGE", "OUT_DATA_STAGE",
"IN_STATUS_STAGE", "OUT_STATUS_STAGE", "STALL",
"WAIT_ACK_SET_CONF_INTERF"
};
#define EP0_STNAME(udc) ep0_state_name[(udc)->ep0state]
#define EP0_FIFO_SIZE 16U
#define BULK_FIFO_SIZE 64U
#define ISO_FIFO_SIZE 256U
#define INT_FIFO_SIZE 16U
struct udc_stats {
unsigned long irqs_reset;
unsigned long irqs_suspend;
unsigned long irqs_resume;
unsigned long irqs_reconfig;
};
#define NR_USB_ENDPOINTS (1 + 5) /* ep0 + ep1in-bulk + .. + ep3in-iso */
#define NR_PXA_ENDPOINTS (1 + 14) /* ep0 + epA + epB + .. + epX */
/**
* struct pxa_udc - udc structure
* @regs: mapped IO space
* @irq: udc irq
* @clk: udc clock
* @usb_gadget: udc gadget structure
* @driver: bound gadget (zero, g_ether, g_file_storage, ...)
* @dev: device
* @mach: machine info, used to activate specific GPIO
* @transceiver: external transceiver to handle vbus sense and D+ pullup
* @ep0state: control endpoint state machine state
* @stats: statistics on udc usage
* @udc_usb_ep: array of usb endpoints offered by the gadget
* @pxa_ep: array of pxa available endpoints
* @enabled: UDC was enabled by a previous udc_enable()
* @pullup_on: if pullup resistor connected to D+ pin
* @pullup_resume: if pullup resistor should be connected to D+ pin on resume
* @config: UDC active configuration
* @last_interface: UDC interface of the last SET_INTERFACE host request
* @last_alternate: UDC altsetting of the last SET_INTERFACE host request
* @udccsr0: save of udccsr0 in case of suspend
* @debugfs_root: root entry of debug filesystem
* @debugfs_state: debugfs entry for "udcstate"
* @debugfs_queues: debugfs entry for "queues"
* @debugfs_eps: debugfs entry for "epstate"
*/
struct pxa_udc {
void __iomem *regs;
int irq;
struct clk *clk;
struct usb_gadget gadget;
struct usb_gadget_driver *driver;
struct device *dev;
struct pxa2xx_udc_mach_info *mach;
struct otg_transceiver *transceiver;
enum ep0_state ep0state;
struct udc_stats stats;
struct udc_usb_ep udc_usb_ep[NR_USB_ENDPOINTS];
struct pxa_ep pxa_ep[NR_PXA_ENDPOINTS];
unsigned enabled:1;
unsigned pullup_on:1;
unsigned pullup_resume:1;
unsigned vbus_sensed:1;
unsigned config:2;
unsigned last_interface:3;
unsigned last_alternate:3;
#ifdef CONFIG_PM
unsigned udccsr0;
#endif
#ifdef CONFIG_USB_GADGET_DEBUG_FS
struct dentry *debugfs_root;
struct dentry *debugfs_state;
struct dentry *debugfs_queues;
struct dentry *debugfs_eps;
#endif
};
static inline struct pxa_udc *to_gadget_udc(struct usb_gadget *gadget)
{
return container_of(gadget, struct pxa_udc, gadget);
}
/*
* Debugging/message support
*/
#define ep_dbg(ep, fmt, arg...) \
dev_dbg(ep->dev->dev, "%s:%s: " fmt, EPNAME(ep), __func__, ## arg)
#define ep_vdbg(ep, fmt, arg...) \
dev_vdbg(ep->dev->dev, "%s:%s: " fmt, EPNAME(ep), __func__, ## arg)
#define ep_err(ep, fmt, arg...) \
dev_err(ep->dev->dev, "%s:%s: " fmt, EPNAME(ep), __func__, ## arg)
#define ep_info(ep, fmt, arg...) \
dev_info(ep->dev->dev, "%s:%s: " fmt, EPNAME(ep), __func__, ## arg)
#define ep_warn(ep, fmt, arg...) \
dev_warn(ep->dev->dev, "%s:%s:" fmt, EPNAME(ep), __func__, ## arg)
#endif /* __LINUX_USB_GADGET_PXA27X_H */
Reference in New Issue View Git Blame Copy Permalink