korg/linux
0
0
Fork 0
mirror of https://mirrors.bfsu.edu.cn/git/linux.git synced 2024-11-18 01:34:14 +08:00
Code Issues Packages Projects Releases Wiki Activity
93b43f13b5
linux/drivers/media/video/bttv-cards.c
Peter Skipworth 93b43f13b5 [PATCH] BTTV support for Adlink RTV24 capture card 
The bttv module currently lacks support for the Adlink RTV24 capture card.
The following patch adds support for the Adlink RTV24 video capture card to
the bttv module.

Cc: Gerd Knorr <kraxel@bytesex.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-06-24 00:06:37 -07:00

4435 lines
129 KiB
C
Raw Blame History

/*
$Id: bttv-cards.c,v 1.47 2005/02/22 14:06:32 kraxel Exp $
bttv-cards.c
this file has configuration informations - card-specific stuff
like the big tvcards array for the most part
Copyright (C) 1996,97,98 Ralph Metzler (rjkm@thp.uni-koeln.de)
& Marcus Metzler (mocm@thp.uni-koeln.de)
(c) 1999-2001 Gerd Knorr <kraxel@goldbach.in-berlin.de>
This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software
Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/config.h>
#include <linux/delay.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/kmod.h>
#include <linux/init.h>
#include <linux/pci.h>
#include <linux/vmalloc.h>
#include <linux/firmware.h>
#include <asm/io.h>
#include "bttvp.h"
#if 0 /* not working yet */
#include "bt832.h"
#endif
/* fwd decl */
static void boot_msp34xx(struct bttv *btv, int pin);
static void boot_bt832(struct bttv *btv);
static void hauppauge_eeprom(struct bttv *btv);
static void avermedia_eeprom(struct bttv *btv);
static void osprey_eeprom(struct bttv *btv);
static void modtec_eeprom(struct bttv *btv);
static void init_PXC200(struct bttv *btv);
static void init_RTV24(struct bttv *btv);
static void winview_audio(struct bttv *btv, struct video_audio *v, int set);
static void lt9415_audio(struct bttv *btv, struct video_audio *v, int set);
static void avermedia_tvphone_audio(struct bttv *btv, struct video_audio *v,
int set);
static void avermedia_tv_stereo_audio(struct bttv *btv, struct video_audio *v,
int set);
static void terratv_audio(struct bttv *btv, struct video_audio *v, int set);
static void gvbctv3pci_audio(struct bttv *btv, struct video_audio *v, int set);
static void gvbctv5pci_audio(struct bttv *btv, struct video_audio *v, int set);
static void winfast2000_audio(struct bttv *btv, struct video_audio *v, int set);
static void pvbt878p9b_audio(struct bttv *btv, struct video_audio *v, int set);
static void fv2000s_audio(struct bttv *btv, struct video_audio *v, int set);
static void windvr_audio(struct bttv *btv, struct video_audio *v, int set);
static void adtvk503_audio(struct bttv *btv, struct video_audio *v, int set);
static void rv605_muxsel(struct bttv *btv, unsigned int input);
static void eagle_muxsel(struct bttv *btv, unsigned int input);
static void xguard_muxsel(struct bttv *btv, unsigned int input);
static void ivc120_muxsel(struct bttv *btv, unsigned int input);
static void gvc1100_muxsel(struct bttv *btv, unsigned int input);
static void PXC200_muxsel(struct bttv *btv, unsigned int input);
static void picolo_tetra_muxsel(struct bttv *btv, unsigned int input);
static void picolo_tetra_init(struct bttv *btv);
static void tibetCS16_muxsel(struct bttv *btv, unsigned int input);
static void tibetCS16_init(struct bttv *btv);
static void kodicom4400r_muxsel(struct bttv *btv, unsigned int input);
static void kodicom4400r_init(struct bttv *btv);
static void sigmaSLC_muxsel(struct bttv *btv, unsigned int input);
static void sigmaSQ_muxsel(struct bttv *btv, unsigned int input);
static int terratec_active_radio_upgrade(struct bttv *btv);
static int tea5757_read(struct bttv *btv);
static int tea5757_write(struct bttv *btv, int value);
static void identify_by_eeprom(struct bttv *btv,
unsigned char eeprom_data[256]);
static int __devinit pvr_boot(struct bttv *btv);
/* config variables */
static unsigned int triton1=0;
static unsigned int vsfx=0;
static unsigned int latency = UNSET;
static unsigned int no_overlay=-1;
static unsigned int card[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
static unsigned int pll[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
static unsigned int tuner[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
static unsigned int svhs[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
static unsigned int remote[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = UNSET };
static struct bttv *master[BTTV_MAX] = { [ 0 ... (BTTV_MAX-1) ] = NULL };
#ifdef MODULE
static unsigned int autoload = 1;
#else
static unsigned int autoload = 0;
#endif
static unsigned int gpiomask = UNSET;
static unsigned int audioall = UNSET;
static unsigned int audiomux[5] = { [ 0 ... 4 ] = UNSET };
/* insmod options */
module_param(triton1, int, 0444);
module_param(vsfx, int, 0444);
module_param(no_overlay, int, 0444);
module_param(latency, int, 0444);
module_param(gpiomask, int, 0444);
module_param(audioall, int, 0444);
module_param(autoload, int, 0444);
module_param_array(card, int, NULL, 0444);
module_param_array(pll, int, NULL, 0444);
module_param_array(tuner, int, NULL, 0444);
module_param_array(svhs, int, NULL, 0444);
module_param_array(remote, int, NULL, 0444);
module_param_array(audiomux, int, NULL, 0444);
MODULE_PARM_DESC(triton1,"set ETBF pci config bit "
"[enable bug compatibility for triton1 + others]");
MODULE_PARM_DESC(vsfx,"set VSFX pci config bit "
"[yet another chipset flaw workaround]");
MODULE_PARM_DESC(latency,"pci latency timer");
MODULE_PARM_DESC(card,"specify TV/grabber card model, see CARDLIST file for a list");
MODULE_PARM_DESC(pll,"specify installed crystal (0=none, 28=28 MHz, 35=35 MHz)");
MODULE_PARM_DESC(tuner,"specify installed tuner type");
MODULE_PARM_DESC(autoload,"automatically load i2c modules like tuner.o, default is 1 (yes)");
/* ----------------------------------------------------------------------- */
/* list of card IDs for bt878+ cards */
static struct CARD {
unsigned id;
int cardnr;
char *name;
} cards[] __devinitdata = {
{ 0x13eb0070, BTTV_HAUPPAUGE878, "Hauppauge WinTV" },
{ 0x39000070, BTTV_HAUPPAUGE878, "Hauppauge WinTV-D" },
{ 0x45000070, BTTV_HAUPPAUGEPVR, "Hauppauge WinTV/PVR" },
{ 0xff000070, BTTV_OSPREY1x0, "Osprey-100" },
{ 0xff010070, BTTV_OSPREY2x0_SVID,"Osprey-200" },
{ 0xff020070, BTTV_OSPREY500, "Osprey-500" },
{ 0xff030070, BTTV_OSPREY2000, "Osprey-2000" },
{ 0xff040070, BTTV_OSPREY540, "Osprey-540" },
{ 0x00011002, BTTV_ATI_TVWONDER, "ATI TV Wonder" },
{ 0x00031002, BTTV_ATI_TVWONDERVE,"ATI TV Wonder/VE" },
{ 0x6606107d, BTTV_WINFAST2000, "Leadtek WinFast TV 2000" },
{ 0x6607107d, BTTV_WINFASTVC100, "Leadtek WinFast VC 100" },
{ 0x6609107d, BTTV_WINFAST2000, "Leadtek TV 2000 XP" },
{ 0x263610b4, BTTV_STB2, "STB TV PCI FM, Gateway P/N 6000704" },
{ 0x264510b4, BTTV_STB2, "STB TV PCI FM, Gateway P/N 6000704" },
{ 0x402010fc, BTTV_GVBCTV3PCI, "I-O Data Co. GV-BCTV3/PCI" },
{ 0x405010fc, BTTV_GVBCTV4PCI, "I-O Data Co. GV-BCTV4/PCI" },
{ 0x407010fc, BTTV_GVBCTV5PCI, "I-O Data Co. GV-BCTV5/PCI" },
{ 0xd01810fc, BTTV_GVBCTV5PCI, "I-O Data Co. GV-BCTV5/PCI" },
{ 0x001211bd, BTTV_PINNACLE, "Pinnacle PCTV" },
// some cards ship with byteswapped IDs ...
{ 0x1200bd11, BTTV_PINNACLE, "Pinnacle PCTV [bswap]" },
{ 0xff00bd11, BTTV_PINNACLE, "Pinnacle PCTV [bswap]" },
// this seems to happen as well ...
{ 0xff1211bd, BTTV_PINNACLE, "Pinnacle PCTV" },
{ 0x3000121a, BTTV_VOODOOTV_FM, "3Dfx VoodooTV FM/ VoodooTV 200" },
{ 0x263710b4, BTTV_VOODOOTV_FM, "3Dfx VoodooTV FM/ VoodooTV 200" },
{ 0x3060121a, BTTV_STB2, "3Dfx VoodooTV 100/ STB OEM" },
{ 0x3000144f, BTTV_MAGICTVIEW063, "(Askey Magic/others) TView99 CPH06x" },
{ 0xa005144f, BTTV_MAGICTVIEW063, "CPH06X TView99-Card" },
{ 0x3002144f, BTTV_MAGICTVIEW061, "(Askey Magic/others) TView99 CPH05x" },
{ 0x3005144f, BTTV_MAGICTVIEW061, "(Askey Magic/others) TView99 CPH061/06L (T1/LC)" },
{ 0x5000144f, BTTV_MAGICTVIEW061, "Askey CPH050" },
{ 0x300014ff, BTTV_MAGICTVIEW061, "TView 99 (CPH061)" },
{ 0x300214ff, BTTV_PHOEBE_TVMAS, "Phoebe TV Master (CPH060)" },
{ 0x00011461, BTTV_AVPHONE98, "AVerMedia TVPhone98" },
{ 0x00021461, BTTV_AVERMEDIA98, "AVermedia TVCapture 98" },
{ 0x00031461, BTTV_AVPHONE98, "AVerMedia TVPhone98" },
{ 0x00041461, BTTV_AVERMEDIA98, "AVerMedia TVCapture 98" },
{ 0x03001461, BTTV_AVERMEDIA98, "VDOMATE TV TUNER CARD" },
{ 0x1117153b, BTTV_TERRATVALUE, "Terratec TValue (Philips PAL B/G)" },
{ 0x1118153b, BTTV_TERRATVALUE, "Terratec TValue (Temic PAL B/G)" },
{ 0x1119153b, BTTV_TERRATVALUE, "Terratec TValue (Philips PAL I)" },
{ 0x111a153b, BTTV_TERRATVALUE, "Terratec TValue (Temic PAL I)" },
{ 0x1123153b, BTTV_TERRATVRADIO, "Terratec TV Radio+" },
{ 0x1127153b, BTTV_TERRATV, "Terratec TV+ (V1.05)" },
// clashes with FlyVideo
//{ 0x18521852, BTTV_TERRATV, "Terratec TV+ (V1.10)" },
{ 0x1134153b, BTTV_TERRATVALUE, "Terratec TValue (LR102)" },
{ 0x1135153b, BTTV_TERRATVALUER, "Terratec TValue Radio" }, // LR102
{ 0x5018153b, BTTV_TERRATVALUE, "Terratec TValue" }, // ??
{ 0xff3b153b, BTTV_TERRATVALUER, "Terratec TValue Radio" }, // ??
{ 0x400015b0, BTTV_ZOLTRIX_GENIE, "Zoltrix Genie TV" },
{ 0x400a15b0, BTTV_ZOLTRIX_GENIE, "Zoltrix Genie TV" },
{ 0x400d15b0, BTTV_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" },
{ 0x401015b0, BTTV_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" },
{ 0x401615b0, BTTV_ZOLTRIX_GENIE, "Zoltrix Genie TV / Radio" },
{ 0x1430aa00, BTTV_PV143, "Provideo PV143A" },
{ 0x1431aa00, BTTV_PV143, "Provideo PV143B" },
{ 0x1432aa00, BTTV_PV143, "Provideo PV143C" },
{ 0x1433aa00, BTTV_PV143, "Provideo PV143D" },
{ 0x1433aa03, BTTV_PV143, "Security Eyes" },
{ 0x1460aa00, BTTV_PV150, "Provideo PV150A-1" },
{ 0x1461aa01, BTTV_PV150, "Provideo PV150A-2" },
{ 0x1462aa02, BTTV_PV150, "Provideo PV150A-3" },
{ 0x1463aa03, BTTV_PV150, "Provideo PV150A-4" },
{ 0x1464aa04, BTTV_PV150, "Provideo PV150B-1" },
{ 0x1465aa05, BTTV_PV150, "Provideo PV150B-2" },
{ 0x1466aa06, BTTV_PV150, "Provideo PV150B-3" },
{ 0x1467aa07, BTTV_PV150, "Provideo PV150B-4" },
{ 0xa132ff00, BTTV_IVC100, "IVC-100" },
{ 0xa1550000, BTTV_IVC200, "IVC-200" },
{ 0xa1550001, BTTV_IVC200, "IVC-200" },
{ 0xa1550002, BTTV_IVC200, "IVC-200" },
{ 0xa1550003, BTTV_IVC200, "IVC-200" },
{ 0xa1550100, BTTV_IVC200, "IVC-200G" },
{ 0xa1550101, BTTV_IVC200, "IVC-200G" },
{ 0xa1550102, BTTV_IVC200, "IVC-200G" },
{ 0xa1550103, BTTV_IVC200, "IVC-200G" },
{ 0xa182ff00, BTTV_IVC120, "IVC-120G" },
{ 0xa182ff01, BTTV_IVC120, "IVC-120G" },
{ 0xa182ff02, BTTV_IVC120, "IVC-120G" },
{ 0xa182ff03, BTTV_IVC120, "IVC-120G" },
{ 0xa182ff04, BTTV_IVC120, "IVC-120G" },
{ 0xa182ff05, BTTV_IVC120, "IVC-120G" },
{ 0xa182ff06, BTTV_IVC120, "IVC-120G" },
{ 0xa182ff07, BTTV_IVC120, "IVC-120G" },
{ 0xa182ff08, BTTV_IVC120, "IVC-120G" },
{ 0xa182ff09, BTTV_IVC120, "IVC-120G" },
{ 0xa182ff0a, BTTV_IVC120, "IVC-120G" },
{ 0xa182ff0b, BTTV_IVC120, "IVC-120G" },
{ 0xa182ff0c, BTTV_IVC120, "IVC-120G" },
{ 0xa182ff0d, BTTV_IVC120, "IVC-120G" },
{ 0xa182ff0e, BTTV_IVC120, "IVC-120G" },
{ 0xa182ff0f, BTTV_IVC120, "IVC-120G" },
{ 0x41424344, BTTV_GRANDTEC, "GrandTec Multi Capture" },
{ 0x01020304, BTTV_XGUARD, "Grandtec Grand X-Guard" },
{ 0x18501851, BTTV_CHRONOS_VS2, "FlyVideo 98 (LR50)/ Chronos Video Shuttle II" },
{ 0xa0501851, BTTV_CHRONOS_VS2, "FlyVideo 98 (LR50)/ Chronos Video Shuttle II" },
{ 0x18511851, BTTV_FLYVIDEO98EZ, "FlyVideo 98EZ (LR51)/ CyberMail AV" },
{ 0x18521852, BTTV_TYPHOON_TVIEW, "FlyVideo 98FM (LR50)/ Typhoon TView TV/FM Tuner" },
{ 0x41a0a051, BTTV_FLYVIDEO_98FM, "Lifeview FlyVideo 98 LR50 Rev Q" },
{ 0x18501f7f, BTTV_FLYVIDEO_98, "Lifeview Flyvideo 98" },
{ 0x010115cb, BTTV_GMV1, "AG GMV1" },
{ 0x010114c7, BTTV_MODTEC_205, "Modular Technology MM201/MM202/MM205/MM210/MM215 PCTV" },
{ 0x10b42636, BTTV_HAUPPAUGE878, "STB ???" },
{ 0x217d6606, BTTV_WINFAST2000, "Leadtek WinFast TV 2000" },
{ 0xfff6f6ff, BTTV_WINFAST2000, "Leadtek WinFast TV 2000" },
{ 0x03116000, BTTV_SENSORAY311, "Sensoray 311" },
{ 0x00790e11, BTTV_WINDVR, "Canopus WinDVR PCI" },
{ 0xa0fca1a0, BTTV_ZOLTRIX, "Face to Face Tvmax" },
{ 0x20007063, BTTV_PC_HDTV, "pcHDTV HD-2000 TV"},
{ 0x82b2aa6a, BTTV_SIMUS_GVC1100, "SIMUS GVC1100" },
{ 0x146caa0c, BTTV_PV951, "ituner spectra8" },
{ 0x200a1295, BTTV_PXC200, "ImageNation PXC200A" },
{ 0x40111554, BTTV_PV_BT878P_9B, "Prolink Pixelview PV-BT" },
{ 0x17de0a01, BTTV_KWORLD, "Mecer TV/FM/Video Tuner" },
{ 0x01051805, BTTV_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #1" },
{ 0x01061805, BTTV_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #2" },
{ 0x01071805, BTTV_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #3" },
{ 0x01081805, BTTV_PICOLO_TETRA_CHIP, "Picolo Tetra Chip #4" },
// likely broken, vendor id doesn't match the other magic views ...
//{ 0xa0fca04f, BTTV_MAGICTVIEW063, "Guillemot Maxi TV Video 3" },
// DVB cards (using pci function .1 for mpeg data xfer)
{ 0x01010071, BTTV_NEBULA_DIGITV, "Nebula Electronics DigiTV" },
{ 0x07611461, BTTV_AVDVBT_761, "AverMedia AverTV DVB-T 761" },
{ 0x001c11bd, BTTV_PINNACLESAT, "Pinnacle PCTV Sat" },
{ 0x002611bd, BTTV_TWINHAN_DST, "Pinnacle PCTV SAT CI" },
{ 0x00011822, BTTV_TWINHAN_DST, "Twinhan VisionPlus DVB" },
{ 0xfc00270f, BTTV_TWINHAN_DST, "ChainTech digitop DST-1000 DVB-S" },
{ 0x07711461, BTTV_AVDVBT_771, "AVermedia AverTV DVB-T 771" },
{ 0xdb1018ac, BTTV_DVICO_DVBT_LITE, "DVICO FusionHDTV DVB-T Lite" },
{ 0, -1, NULL }
};
/* ----------------------------------------------------------------------- */
/* array with description for bt848 / bt878 tv/grabber cards */
struct tvcard bttv_tvcards[] = {
{
/* ---- card 0x00 ---------------------------------- */
.name = " *** UNKNOWN/GENERIC *** ",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.muxsel = { 2, 3, 1, 0},
.tuner_type = -1,
},{
.name = "MIRO PCTV",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 15,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 2, 0, 0, 0, 10},
.needs_tvaudio = 1,
.tuner_type = -1,
},{
.name = "Hauppauge (bt848)",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 7,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0, 1, 2, 3, 4},
.needs_tvaudio = 1,
.tuner_type = -1,
},{
.name = "STB, Gateway P/N 6000699 (bt848)",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 7,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 4, 0, 2, 3, 1},
.no_msp34xx = 1,
.needs_tvaudio = 1,
.tuner_type = TUNER_PHILIPS_NTSC,
.pll = PLL_28,
.has_radio = 1,
},{
/* ---- card 0x04 ---------------------------------- */
.name = "Intel Create and Share PCI/ Smart Video Recorder III",
.video_inputs = 4,
.audio_inputs = 0,
.tuner = -1,
.svhs = 2,
.gpiomask = 0,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0 },
.needs_tvaudio = 0,
.tuner_type = 4,
},{
.name = "Diamond DTV2000",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 3,
.muxsel = { 2, 3, 1, 0},
.audiomux = { 0, 1, 0, 1, 3},
.needs_tvaudio = 1,
.tuner_type = -1,
},{
.name = "AVerMedia TVPhone",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 3,
.muxsel = { 2, 3, 1, 1},
.gpiomask = 0x0f,
.audiomux = { 0x0c, 0x04, 0x08, 0x04, 0},
/* 0x04 for some cards ?? */
.needs_tvaudio = 1,
.tuner_type = -1,
.audio_hook = avermedia_tvphone_audio,
.has_remote = 1,
},{
.name = "MATRIX-Vision MV-Delta",
.video_inputs = 5,
.audio_inputs = 1,
.tuner = -1,
.svhs = 3,
.gpiomask = 0,
.muxsel = { 2, 3, 1, 0, 0},
.audiomux = {0 },
.needs_tvaudio = 1,
.tuner_type = -1,
},{
/* ---- card 0x08 ---------------------------------- */
.name = "Lifeview FlyVideo II (Bt848) LR26 / MAXI TV Video PCI2 LR26",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0xc00,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0, 0xc00, 0x800, 0x400, 0xc00, 0},
.needs_tvaudio = 1,
.pll = PLL_28,
.tuner_type = -1,
},{
.name = "IMS/IXmicro TurboTV",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 3,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 1, 1, 2, 3, 0},
.needs_tvaudio = 0,
.pll = PLL_28,
.tuner_type = TUNER_TEMIC_PAL,
},{
.name = "Hauppauge (bt878)",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x0f, /* old: 7 */
.muxsel = { 2, 0, 1, 1},
.audiomux = { 0, 1, 2, 3, 4},
.needs_tvaudio = 1,
.pll = PLL_28,
.tuner_type = -1,
},{
.name = "MIRO PCTV pro",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x3014f,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0x20001,0x10001, 0, 0,10},
.needs_tvaudio = 1,
.tuner_type = -1,
},{
/* ---- card 0x0c ---------------------------------- */
.name = "ADS Technologies Channel Surfer TV (bt848)",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 15,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 13, 14, 11, 7, 0, 0},
.needs_tvaudio = 1,
.tuner_type = -1,
},{
.name = "AVerMedia TVCapture 98",
.video_inputs = 3,
.audio_inputs = 4,
.tuner = 0,
.svhs = 2,
.gpiomask = 15,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 13, 14, 11, 7, 0, 0},
.needs_tvaudio = 1,
.msp34xx_alt = 1,
.pll = PLL_28,
.tuner_type = TUNER_PHILIPS_PAL,
.audio_hook = avermedia_tv_stereo_audio,
},{
.name = "Aimslab Video Highway Xtreme (VHX)",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 7,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0, 2, 1, 3, 4}, /* old: { 0, 1, 2, 3, 4} */
.needs_tvaudio = 1,
.pll = PLL_28,
.tuner_type = -1,
},{
.name = "Zoltrix TV-Max",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 15,
.muxsel = { 2, 3, 1, 1},
.audiomux = {0 , 0, 1 , 0, 10},
.needs_tvaudio = 1,
.tuner_type = -1,
},{
/* ---- card 0x10 ---------------------------------- */
.name = "Prolink Pixelview PlayTV (bt878)",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x01fe00,
.muxsel = { 2, 3, 1, 1},
#if 0
// old
.audiomux = { 0x01c000, 0, 0x018000, 0x014000, 0x002000, 0 },
#else
// 2003-10-20 by "Anton A. Arapov" <arapov@mail.ru>
.audiomux = { 0x001e00, 0, 0x018000, 0x014000, 0x002000, 0 },
#endif
.needs_tvaudio = 1,
.pll = PLL_28,
.tuner_type = -1,
},{
.name = "Leadtek WinView 601",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x8300f8,
.muxsel = { 2, 3, 1, 1,0},
.audiomux = { 0x4fa007,0xcfa007,0xcfa007,0xcfa007,0xcfa007,0xcfa007},
.needs_tvaudio = 1,
.tuner_type = -1,
.audio_hook = winview_audio,
.has_radio = 1,
},{
.name = "AVEC Intercapture",
.video_inputs = 3,
.audio_inputs = 2,
.tuner = 0,
.svhs = 2,
.gpiomask = 0,
.muxsel = {2, 3, 1, 1},
.audiomux = {1, 0, 0, 0, 0},
.needs_tvaudio = 1,
.tuner_type = -1,
},{
.name = "Lifeview FlyVideo II EZ /FlyKit LR38 Bt848 (capture only)",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = -1,
.svhs = -1,
.gpiomask = 0x8dff00,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0 },
.no_msp34xx = 1,
.tuner_type = -1,
},{
/* ---- card 0x14 ---------------------------------- */
.name = "CEI Raffles Card",
.video_inputs = 3,
.audio_inputs = 3,
.tuner = 0,
.svhs = 2,
.muxsel = {2, 3, 1, 1},
.tuner_type = -1,
},{
.name = "Lifeview FlyVideo 98/ Lucky Star Image World ConferenceTV LR50",
.video_inputs = 4,
.audio_inputs = 2, // tuner, line in
.tuner = 0,
.svhs = 2,
.gpiomask = 0x1800,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0, 0x800, 0x1000, 0x1000, 0x1800},
.pll = PLL_28,
.tuner_type = TUNER_PHILIPS_PAL_I,
},{
.name = "Askey CPH050/ Phoebe Tv Master + FM",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0xc00,
.muxsel = { 2, 3, 1, 1},
.audiomux = {0, 1, 0x800, 0x400, 0xc00, 0},
.needs_tvaudio = 1,
.pll = PLL_28,
.tuner_type = -1,
},{
.name = "Modular Technology MM201/MM202/MM205/MM210/MM215 PCTV, bt878",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = -1,
.gpiomask = 7,
.muxsel = { 2, 3, -1 },
.digital_mode = DIGITAL_MODE_CAMERA,
.audiomux = { 0, 0, 0, 0, 0 },
.no_msp34xx = 1,
.pll = PLL_28,
.tuner_type = TUNER_ALPS_TSBB5_PAL_I,
},{
/* ---- card 0x18 ---------------------------------- */
.name = "Askey CPH05X/06X (bt878) [many vendors]",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0xe00,
.muxsel = { 2, 3, 1, 1},
.audiomux = {0x400, 0x400, 0x400, 0x400, 0xc00},
.needs_tvaudio = 1,
.pll = PLL_28,
.tuner_type = -1,
.has_remote = 1,
},{
.name = "Terratec TerraTV+ Version 1.0 (Bt848)/ Terra TValue Version 1.0/ Vobis TV-Boostar",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x1f0fff,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0x20000, 0x30000, 0x10000, 0, 0x40000},
.needs_tvaudio = 0,
.tuner_type = TUNER_PHILIPS_PAL,
.audio_hook = terratv_audio,
},{
.name = "Hauppauge WinCam newer (bt878)",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 3,
.gpiomask = 7,
.muxsel = { 2, 0, 1, 1},
.audiomux = { 0, 1, 2, 3, 4},
.needs_tvaudio = 1,
.tuner_type = -1,
},{
.name = "Lifeview FlyVideo 98/ MAXI TV Video PCI2 LR50",
.video_inputs = 4,
.audio_inputs = 2,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x1800,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0, 0x800, 0x1000, 0x1000, 0x1800},
.pll = PLL_28,
.tuner_type = TUNER_PHILIPS_SECAM,
},{
/* ---- card 0x1c ---------------------------------- */
.name = "Terratec TerraTV+ Version 1.1 (bt878)",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x1f0fff,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0x20000, 0x30000, 0x10000, 0x00000, 0x40000},
.needs_tvaudio = 0,
.tuner_type = TUNER_PHILIPS_PAL,
.audio_hook = terratv_audio,
/* GPIO wiring:
External 20 pin connector (for Active Radio Upgrade board)
gpio00: i2c-sda
gpio01: i2c-scl
gpio02: om5610-data
gpio03: om5610-clk
gpio04: om5610-wre
gpio05: om5610-stereo
gpio06: rds6588-davn
gpio07: Pin 7 n.c.
gpio08: nIOW
gpio09+10: nIOR, nSEL ?? (bt878)
gpio09: nIOR (bt848)
gpio10: nSEL (bt848)
Sound Routing:
gpio16: u2-A0 (1st 4052bt)
gpio17: u2-A1
gpio18: u2-nEN
gpio19: u4-A0 (2nd 4052)
gpio20: u4-A1
u4-nEN - GND
Btspy:
00000 : Cdrom (internal audio input)
10000 : ext. Video audio input
20000 : TV Mono
a0000 : TV Mono/2
1a0000 : TV Stereo
30000 : Radio
40000 : Mute
*/
},{
/* Jannik Fritsch <jannik@techfak.uni-bielefeld.de> */
.name = "Imagenation PXC200",
.video_inputs = 5,
.audio_inputs = 1,
.tuner = -1,
.svhs = 1, /* was: 4 */
.gpiomask = 0,
.muxsel = { 2, 3, 1, 0, 0},
.audiomux = { 0 },
.needs_tvaudio = 1,
.tuner_type = -1,
.muxsel_hook = PXC200_muxsel,
},{
.name = "Lifeview FlyVideo 98 LR50",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x1800, //0x8dfe00
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0, 0x0800, 0x1000, 0x1000, 0x1800, 0 },
.pll = PLL_28,
.tuner_type = -1,
},{
.name = "Formac iProTV, Formac ProTV I (bt848)",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 3,
.gpiomask = 1,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 1, 0, 0, 0, 0 },
.pll = PLL_28,
.tuner_type = TUNER_PHILIPS_PAL,
},{
/* ---- card 0x20 ---------------------------------- */
.name = "Intel Create and Share PCI/ Smart Video Recorder III",
.video_inputs = 4,
.audio_inputs = 0,
.tuner = -1,
.svhs = 2,
.gpiomask = 0,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0 },
.needs_tvaudio = 0,
.tuner_type = 4,
},{
.name = "Terratec TerraTValue Version Bt878",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0xffff00,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0x500, 0, 0x300, 0x900, 0x900},
.needs_tvaudio = 1,
.pll = PLL_28,
.tuner_type = TUNER_PHILIPS_PAL,
},{
.name = "Leadtek WinFast 2000/ WinFast 2000 XP",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.muxsel = { 2, 3, 1, 1, 0}, // TV, CVid, SVid, CVid over SVid connector
#if 0
.gpiomask = 0xc33000,
.audiomux = { 0x422000,0x1000,0x0000,0x620000,0x800000 },
#else
/* Alexander Varakin <avarakin@hotmail.com> [stereo version] */
.gpiomask = 0xb33000,
.audiomux = { 0x122000,0x1000,0x0000,0x620000,0x800000 },
#endif
/* Audio Routing for "WinFast 2000 XP" (no tv stereo !)
gpio23 -- hef4052:nEnable (0x800000)
gpio12 -- hef4052:A1
gpio13 -- hef4052:A0
0x0000: external audio
0x1000: FM
0x2000: TV
0x3000: n.c.
Note: There exists another variant "Winfast 2000" with tv stereo !?
Note: eeprom only contains FF and pci subsystem id 107d:6606
*/
.needs_tvaudio = 0,
.pll = PLL_28,
.has_radio = 1,
.tuner_type = 5, // default for now, gpio reads BFFF06 for Pal bg+dk
.audio_hook = winfast2000_audio,
.has_remote = 1,
},{
.name = "Lifeview FlyVideo 98 LR50 / Chronos Video Shuttle II",
.video_inputs = 4,
.audio_inputs = 3,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x1800,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0, 0x800, 0x1000, 0x1000, 0x1800},
.pll = PLL_28,
.tuner_type = -1,
},{
/* ---- card 0x24 ---------------------------------- */
.name = "Lifeview FlyVideo 98FM LR50 / Typhoon TView TV/FM Tuner",
.video_inputs = 4,
.audio_inputs = 3,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x1800,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0, 0x800, 0x1000, 0x1000, 0x1800, 0 },
.pll = PLL_28,
.tuner_type = -1,
.has_radio = 1,
},{
.name = "Prolink PixelView PlayTV pro",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0xff,
.muxsel = { 2, 3, 1, 1 },
.audiomux = { 0x21, 0x20, 0x24, 0x2c, 0x29, 0x29 },
.no_msp34xx = 1,
.pll = PLL_28,
.tuner_type = -1,
},{
.name = "Askey CPH06X TView99",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x551e00,
.muxsel = { 2, 3, 1, 0},
.audiomux = { 0x551400, 0x551200, 0, 0, 0x551c00, 0x551200 },
.needs_tvaudio = 1,
.pll = PLL_28,
.tuner_type = 1,
.has_remote = 1,
},{
.name = "Pinnacle PCTV Studio/Rave",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x03000F,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 2, 0xd0001, 0, 0, 1},
.needs_tvaudio = 0,
.pll = PLL_28,
.tuner_type = -1,
},{
/* ---- card 0x28 ---------------------------------- */
.name = "STB TV PCI FM, Gateway P/N 6000704 (bt878), 3Dfx VoodooTV 100",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 7,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 4, 0, 2, 3, 1},
.no_msp34xx = 1,
.needs_tvaudio = 1,
.tuner_type = TUNER_PHILIPS_NTSC,
.pll = PLL_28,
.has_radio = 1,
},{
.name = "AVerMedia TVPhone 98",
.video_inputs = 3,
.audio_inputs = 4,
.tuner = 0,
.svhs = 2,
.gpiomask = 15,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 13, 4, 11, 7, 0, 0},
.needs_tvaudio = 1,
.pll = PLL_28,
.tuner_type = -1,
.has_radio = 1,
.audio_hook = avermedia_tvphone_audio,
},{
.name = "ProVideo PV951", /* pic16c54 */
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0, 0, 0, 0, 0},
.needs_tvaudio = 1,
.no_msp34xx = 1,
.pll = PLL_28,
.tuner_type = 1,
},{
.name = "Little OnAir TV",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0xe00b,
.muxsel = {2, 3, 1, 1},
.audiomux = {0xff9ff6, 0xff9ff6, 0xff1ff7, 0, 0xff3ffc},
.no_msp34xx = 1,
.tuner_type = -1,
},{
/* ---- card 0x2c ---------------------------------- */
.name = "Sigma TVII-FM",
.video_inputs = 2,
.audio_inputs = 1,
.tuner = 0,
.svhs = -1,
.gpiomask = 3,
.muxsel = {2, 3, 1, 1},
.audiomux = {1, 1, 0, 2, 3},
.no_msp34xx = 1,
.pll = PLL_NONE,
.tuner_type = -1,
},{
.name = "MATRIX-Vision MV-Delta 2",
.video_inputs = 5,
.audio_inputs = 1,
.tuner = -1,
.svhs = 3,
.gpiomask = 0,
.muxsel = { 2, 3, 1, 0, 0},
.audiomux = {0 },
.no_msp34xx = 1,
.pll = PLL_28,
.tuner_type = -1,
},{
.name = "Zoltrix Genie TV/FM",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0xbcf03f,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0xbc803f, 0xbc903f, 0xbcb03f, 0, 0xbcb03f},
.no_msp34xx = 1,
.pll = PLL_28,
.tuner_type = 21,
},{
.name = "Terratec TV/Radio+",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x70000,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0x20000, 0x30000, 0x10000, 0, 0x40000, 0x20000 },
.needs_tvaudio = 1,
.no_msp34xx = 1,
.pll = PLL_35,
.tuner_type = 1,
.has_radio = 1,
},{
/* ---- card 0x30 ---------------------------------- */
.name = "Askey CPH03x/ Dynalink Magic TView",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 15,
.muxsel = { 2, 3, 1, 1},
.audiomux = {2,0,0,0,1},
.needs_tvaudio = 1,
.pll = PLL_28,
.tuner_type = -1,
},{
.name = "IODATA GV-BCTV3/PCI",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x010f00,
.muxsel = {2, 3, 0, 0},
.audiomux = {0x10000, 0, 0x10000, 0, 0, 0},
.no_msp34xx = 1,
.pll = PLL_28,
.tuner_type = TUNER_ALPS_TSHC6_NTSC,
.audio_hook = gvbctv3pci_audio,
},{
.name = "Prolink PV-BT878P+4E / PixelView PlayTV PAK / Lenco MXTV-9578 CP",
.video_inputs = 5,
.audio_inputs = 1,
.tuner = 0,
.svhs = 3,
.gpiomask = 0xAA0000,
.muxsel = { 2,3,1,1,-1 },
.digital_mode = DIGITAL_MODE_CAMERA,
.audiomux = { 0x20000, 0, 0x80000, 0x80000, 0xa8000, 0x46000 },
.no_msp34xx = 1,
.pll = PLL_28,
.tuner_type = TUNER_PHILIPS_PAL_I,
.has_remote = 1,
/* GPIO wiring: (different from Rev.4C !)
GPIO17: U4.A0 (first hef4052bt)
GPIO19: U4.A1
GPIO20: U5.A1 (second hef4052bt)
GPIO21: U4.nEN
GPIO22: BT832 Reset Line
GPIO23: A5,A0, U5,nEN
Note: At i2c=0x8a is a Bt832 chip, which changes to 0x88 after being reset via GPIO22
*/
},{
.name = "Eagle Wireless Capricorn2 (bt878A)",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 7,
.muxsel = { 2, 0, 1, 1},
.audiomux = { 0, 1, 2, 3, 4},
.pll = PLL_28,
.tuner_type = -1 /* TUNER_ALPS_TMDH2_NTSC */,
},{
/* ---- card 0x34 ---------------------------------- */
/* David H<>rdeman <david@2gen.com> */
.name = "Pinnacle PCTV Studio Pro",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 3,
.gpiomask = 0x03000F,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 1, 0xd0001, 0, 0, 10},
/* sound path (5 sources):
MUX1 (mask 0x03), Enable Pin 0x08 (0=enable, 1=disable)
0= ext. Audio IN
1= from MUX2
2= Mono TV sound from Tuner
3= not connected
MUX2 (mask 0x30000):
0,2,3= from MSP34xx
1= FM stereo Radio from Tuner */
.needs_tvaudio = 0,
.pll = PLL_28,
.tuner_type = -1,
},{
/* Claas Langbehn <claas@bigfoot.com>,
Sven Grothklags <sven@upb.de> */
.name = "Typhoon TView RDS + FM Stereo / KNC1 TV Station RDS",
.video_inputs = 4,
.audio_inputs = 3,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x1c,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0, 0, 0x10, 8, 4 },
.needs_tvaudio = 1,
.pll = PLL_28,
.tuner_type = TUNER_PHILIPS_PAL,
.has_radio = 1,
},{
/* Tim R<>stermundt <rosterm@uni-muenster.de>
in de.comp.os.unix.linux.hardware:
options bttv card=0 pll=1 radio=1 gpiomask=0x18e0
audiomux=0x44c71f,0x44d71f,0,0x44d71f,0x44dfff
options tuner type=5 */
.name = "Lifeview FlyVideo 2000 /FlyVideo A2/ Lifetec LT 9415 TV [LR90]",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x18e0,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0x0000,0x0800,0x1000,0x1000,0x18e0 },
/* For cards with tda9820/tda9821:
0x0000: Tuner normal stereo
0x0080: Tuner A2 SAP (second audio program = Zweikanalton)
0x0880: Tuner A2 stereo */
.pll = PLL_28,
.tuner_type = -1,
},{
/* Miguel Angel Alvarez <maacruz@navegalia.com>
old Easy TV BT848 version (model CPH031) */
.name = "Askey CPH031/ BESTBUY Easy TV",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0xF,
.muxsel = { 2, 3, 1, 0},
.audiomux = { 2, 0, 0, 0, 10},
.needs_tvaudio = 0,
.pll = PLL_28,
.tuner_type = TUNER_TEMIC_PAL,
},{
/* ---- card 0x38 ---------------------------------- */
/* Gordon Heydon <gjheydon@bigfoot.com ('98) */
.name = "Lifeview FlyVideo 98FM LR50",
.video_inputs = 4,
.audio_inputs = 3,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x1800,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0, 0x800, 0x1000, 0x1000, 0x1800, 0 },
.pll = PLL_28,
.tuner_type = 5,
},{
/* This is the ultimate cheapo capture card
* just a BT848A on a small PCB!
* Steve Hosgood <steve@equiinet.com> */
.name = "GrandTec 'Grand Video Capture' (Bt848)",
.video_inputs = 2,
.audio_inputs = 0,
.tuner = -1,
.svhs = 1,
.gpiomask = 0,
.muxsel = { 3, 1 },
.audiomux = { 0 },
.needs_tvaudio = 0,
.no_msp34xx = 1,
.pll = PLL_35,
.tuner_type = -1,
},{
/* Daniel Herrington <daniel.herrington@home.com> */
.name = "Askey CPH060/ Phoebe TV Master Only (No FM)",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0xe00,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0x400, 0x400, 0x400, 0x400, 0x800, 0x400 },
.needs_tvaudio = 1,
.pll = PLL_28,
.tuner_type = TUNER_TEMIC_4036FY5_NTSC,
},{
/* Matti Mottus <mottus@physic.ut.ee> */
.name = "Askey CPH03x TV Capturer",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x03000F,
.muxsel = { 2, 3, 1, 0},
.audiomux = { 2,0,0,0,1 },
.pll = PLL_28,
.tuner_type = 0,
},{
/* ---- card 0x3c ---------------------------------- */
/* Philip Blundell <philb@gnu.org> */
.name = "Modular Technology MM100PCTV",
.video_inputs = 2,
.audio_inputs = 2,
.tuner = 0,
.svhs = -1,
.gpiomask = 11,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 2, 0, 0, 1, 8},
.pll = PLL_35,
.tuner_type = TUNER_TEMIC_PAL,
},{
/* Adrian Cox <adrian@humboldt.co.uk */
.name = "AG Electronics GMV1",
.video_inputs = 2,
.audio_inputs = 0,
.tuner = -1,
.svhs = 1,
.gpiomask = 0xF,
.muxsel = { 2, 2},
.audiomux = { },
.no_msp34xx = 1,
.needs_tvaudio = 0,
.pll = PLL_28,
.tuner_type = -1,
},{
/* Miguel Angel Alvarez <maacruz@navegalia.com>
new Easy TV BT878 version (model CPH061)
special thanks to Informatica Mieres for providing the card */
.name = "Askey CPH061/ BESTBUY Easy TV (bt878)",
.video_inputs = 3,
.audio_inputs = 2,
.tuner = 0,
.svhs = 2,
.gpiomask = 0xFF,
.muxsel = { 2, 3, 1, 0},
.audiomux = { 1, 0, 4, 4, 9},
.needs_tvaudio = 0,
.pll = PLL_28,
.tuner_type = TUNER_PHILIPS_PAL,
},{
/* Lukas Gebauer <geby@volny.cz> */
.name = "ATI TV-Wonder",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0xf03f,
.muxsel = { 2, 3, 1, 0 },
.audiomux = { 0xbffe, 0, 0xbfff, 0, 0xbffe},
.pll = PLL_28,
.tuner_type = TUNER_TEMIC_4006FN5_MULTI_PAL,
},{
/* ---- card 0x40 ---------------------------------- */
/* Lukas Gebauer <geby@volny.cz> */
.name = "ATI TV-Wonder VE",
.video_inputs = 2,
.audio_inputs = 1,
.tuner = 0,
.svhs = -1,
.gpiomask = 1,
.muxsel = { 2, 3, 0, 1},
.audiomux = { 0, 0, 1, 0, 0},
.no_msp34xx = 1,
.pll = PLL_28,
.tuner_type = TUNER_TEMIC_4006FN5_MULTI_PAL,
},{
/* DeeJay <deejay@westel900.net (2000S) */
.name = "Lifeview FlyVideo 2000S LR90",
.video_inputs = 3,
.audio_inputs = 3,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x18e0,
.muxsel = { 2, 3, 0, 1},
/* Radio changed from 1e80 to 0x800 to make
FlyVideo2000S in .hu happy (gm)*/
/* -dk-???: set mute=0x1800 for tda9874h daughterboard */
.audiomux = { 0x0000,0x0800,0x1000,0x1000,0x1800, 0x1080 },
.audio_hook = fv2000s_audio,
.no_msp34xx = 1,
.no_tda9875 = 1,
.needs_tvaudio = 1,
.pll = PLL_28,
.tuner_type = 5,
},{
.name = "Terratec TValueRadio",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0xffff00,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0x500, 0x500, 0x300, 0x900, 0x900},
.needs_tvaudio = 1,
.pll = PLL_28,
.tuner_type = TUNER_PHILIPS_PAL,
.has_radio = 1,
},{
/* TANAKA Kei <peg00625@nifty.com> */
.name = "IODATA GV-BCTV4/PCI",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x010f00,
.muxsel = {2, 3, 0, 0},
.audiomux = {0x10000, 0, 0x10000, 0, 0, 0},
.no_msp34xx = 1,
.pll = PLL_28,
.tuner_type = TUNER_SHARP_2U5JF5540_NTSC,
.audio_hook = gvbctv3pci_audio,
},{
/* ---- card 0x44 ---------------------------------- */
.name = "3Dfx VoodooTV FM (Euro), VoodooTV 200 (USA)",
// try "insmod msp3400 simple=0" if you have
// sound problems with this card.
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = -1,
.gpiomask = 0x4f8a00,
// 0x100000: 1=MSP enabled (0=disable again)
// 0x010000: Connected to "S0" on tda9880 (0=Pal/BG, 1=NTSC)
.audiomux = {0x947fff, 0x987fff,0x947fff,0x947fff, 0x947fff},
// tvtuner, radio, external,internal, mute, stereo
/* tuner, Composit, SVid, Composit-on-Svid-adapter*/
.muxsel = { 2, 3 ,0 ,1},
.tuner_type = TUNER_MT2032,
.pll = PLL_28,
.has_radio = 1,
},{
/* Philip Blundell <pb@nexus.co.uk> */
.name = "Active Imaging AIMMS",
.video_inputs = 1,
.audio_inputs = 0,
.tuner = -1,
.tuner_type = -1,
.pll = PLL_28,
.muxsel = { 2 },
.gpiomask = 0
},{
/* Tomasz Pyra <hellfire@sedez.iq.pl> */
.name = "Prolink Pixelview PV-BT878P+ (Rev.4C,8E)",
.video_inputs = 3,
.audio_inputs = 4,
.tuner = 0,
.svhs = 2,
.gpiomask = 15,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0, 0, 11, 7, 13, 0}, // TV and Radio with same GPIO !
.needs_tvaudio = 1,
.pll = PLL_28,
.tuner_type = 25,
.has_remote = 1,
/* GPIO wiring:
GPIO0: U4.A0 (hef4052bt)
GPIO1: U4.A1
GPIO2: U4.A1 (second hef4052bt)
GPIO3: U4.nEN, U5.A0, A5.nEN
GPIO8-15: vrd866b ?
*/
},{
.name = "Lifeview FlyVideo 98EZ (capture only) LR51",
.video_inputs = 4,
.audio_inputs = 0,
.tuner = -1,
.svhs = 2,
.muxsel = { 2, 3, 1, 1}, // AV1, AV2, SVHS, CVid adapter on SVHS
.pll = PLL_28,
.no_msp34xx = 1,
},{
/* ---- card 0x48 ---------------------------------- */
/* Dariusz Kowalewski <darekk@automex.pl> */
.name = "Prolink Pixelview PV-BT878P+9B (PlayTV Pro rev.9B FM+NICAM)",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x3f,
.muxsel = { 2, 3, 1, 1 },
.audiomux = { 0x01, 0x00, 0x03, 0x03, 0x09, 0x02 },
.needs_tvaudio = 1,
.no_msp34xx = 1,
.no_tda9875 = 1,
.pll = PLL_28,
.tuner_type = 5,
.audio_hook = pvbt878p9b_audio, // Note: not all cards have stereo
.has_radio = 1, // Note: not all cards have radio
.has_remote = 1,
/* GPIO wiring:
GPIO0: A0 hef4052
GPIO1: A1 hef4052
GPIO3: nEN hef4052
GPIO8-15: vrd866b
GPIO20,22,23: R30,R29,R28
*/
},{
/* Clay Kunz <ckunz@mail.arc.nasa.gov> */
/* you must jumper JP5 for the card to work */
.name = "Sensoray 311",
.video_inputs = 5,
.audio_inputs = 0,
.tuner = -1,
.svhs = 4,
.gpiomask = 0,
.muxsel = { 2, 3, 1, 0, 0},
.audiomux = { 0 },
.needs_tvaudio = 0,
.tuner_type = -1,
},{
/* Miguel Freitas <miguel@cetuc.puc-rio.br> */
.name = "RemoteVision MX (RV605)",
.video_inputs = 16,
.audio_inputs = 0,
.tuner = -1,
.svhs = -1,
.gpiomask = 0x00,
.gpiomask2 = 0x07ff,
.muxsel = { 0x33, 0x13, 0x23, 0x43, 0xf3, 0x73, 0xe3, 0x03,
0xd3, 0xb3, 0xc3, 0x63, 0x93, 0x53, 0x83, 0xa3 },
.no_msp34xx = 1,
.no_tda9875 = 1,
.tuner_type = -1,
.muxsel_hook = rv605_muxsel,
},{
.name = "Powercolor MTV878/ MTV878R/ MTV878F",
.video_inputs = 3,
.audio_inputs = 2,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x1C800F, // Bit0-2: Audio select, 8-12:remote control 14:remote valid 15:remote reset
.muxsel = { 2, 1, 1, },
.audiomux = { 0, 1, 2, 2, 4 },
.needs_tvaudio = 0,
.tuner_type = TUNER_PHILIPS_PAL,
.pll = PLL_28,
.has_radio = 1,
},{
/* ---- card 0x4c ---------------------------------- */
/* Masaki Suzuki <masaki@btree.org> */
.name = "Canopus WinDVR PCI (COMPAQ Presario 3524JP, 5112JP)",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x140007,
.muxsel = { 2, 3, 1, 1 },
.audiomux = { 0, 1, 2, 3, 4, 0 },
.tuner_type = TUNER_PHILIPS_NTSC,
.audio_hook = windvr_audio,
},{
.name = "GrandTec Multi Capture Card (Bt878)",
.video_inputs = 4,
.audio_inputs = 0,
.tuner = -1,
.svhs = -1,
.gpiomask = 0,
.muxsel = { 2, 3, 1, 0 },
.audiomux = { 0 },
.needs_tvaudio = 0,
.no_msp34xx = 1,
.pll = PLL_28,
.tuner_type = -1,
},{
.name = "Jetway TV/Capture JW-TV878-FBK, Kworld KW-TV878RF",
.video_inputs = 4,
.audio_inputs = 3,
.tuner = 0,
.svhs = 2,
.gpiomask = 7,
.muxsel = { 2, 3, 1, 1 }, // Tuner, SVid, SVHS, SVid to SVHS connector
.audiomux = { 0 ,0 ,4, 4,4,4},// Yes, this tuner uses the same audio output for TV and FM radio!
// This card lacks external Audio In, so we mute it on Ext. & Int.
// The PCB can take a sbx1637/sbx1673, wiring unknown.
// This card lacks PCI subsystem ID, sigh.
// audiomux=1: lower volume, 2+3: mute
// btwincap uses 0x80000/0x80003
.needs_tvaudio = 0,
.no_msp34xx = 1,
.pll = PLL_28,
.tuner_type = 5, // Samsung TCPA9095PC27A (BG+DK), philips compatible, w/FM, stereo and
// radio signal strength indicators work fine.
.has_radio = 1,
/* GPIO Info:
GPIO0,1: HEF4052 A0,A1
GPIO2: HEF4052 nENABLE
GPIO3-7: n.c.
GPIO8-13: IRDC357 data0-5 (data6 n.c. ?) [chip not present on my card]
GPIO14,15: ??
GPIO16-21: n.c.
GPIO22,23: ??
?? : mtu8b56ep microcontroller for IR (GPIO wiring unknown)*/
},{
/* Arthur Tetzlaff-Deas, DSP Design Ltd <software@dspdesign.com> */
.name = "DSP Design TCVIDEO",
.video_inputs = 4,
.svhs = -1,
.muxsel = { 2, 3, 1, 0},
.pll = PLL_28,
.tuner_type = -1,
},{
/* ---- card 0x50 ---------------------------------- */
.name = "Hauppauge WinTV PVR",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.muxsel = { 2, 0, 1, 1},
.needs_tvaudio = 1,
.pll = PLL_28,
.tuner_type = -1,
.gpiomask = 7,
.audiomux = {7},
},{
.name = "IODATA GV-BCTV5/PCI",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x0f0f80,
.muxsel = {2, 3, 1, 0},
.audiomux = {0x030000, 0x010000, 0, 0, 0x020000, 0},
.no_msp34xx = 1,
.pll = PLL_28,
.tuner_type = TUNER_PHILIPS_NTSC_M,
.audio_hook = gvbctv5pci_audio,
.has_radio = 1,
},{
.name = "Osprey 100/150 (878)", /* 0x1(2|3)-45C6-C1 */
.video_inputs = 4, /* id-inputs-clock */
.audio_inputs = 0,
.tuner = -1,
.svhs = 3,
.muxsel = { 3, 2, 0, 1 },
.pll = PLL_28,
.tuner_type = -1,
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
},{
.name = "Osprey 100/150 (848)", /* 0x04-54C0-C1 & older boards */
.video_inputs = 3,
.audio_inputs = 0,
.tuner = -1,
.svhs = 2,
.muxsel = { 2, 3, 1 },
.pll = PLL_28,
.tuner_type = -1,
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
},{
/* ---- card 0x54 ---------------------------------- */
.name = "Osprey 101 (848)", /* 0x05-40C0-C1 */
.video_inputs = 2,
.audio_inputs = 0,
.tuner = -1,
.svhs = 1,
.muxsel = { 3, 1 },
.pll = PLL_28,
.tuner_type = -1,
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
},{
.name = "Osprey 101/151", /* 0x1(4|5)-0004-C4 */
.video_inputs = 1,
.audio_inputs = 0,
.tuner = -1,
.svhs = -1,
.muxsel = { 0 },
.pll = PLL_28,
.tuner_type = -1,
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
},{
.name = "Osprey 101/151 w/ svid", /* 0x(16|17|20)-00C4-C1 */
.video_inputs = 2,
.audio_inputs = 0,
.tuner = -1,
.svhs = 1,
.muxsel = { 0, 1 },
.pll = PLL_28,
.tuner_type = -1,
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
},{
.name = "Osprey 200/201/250/251", /* 0x1(8|9|E|F)-0004-C4 */
.video_inputs = 1,
.audio_inputs = 1,
.tuner = -1,
.svhs = -1,
.muxsel = { 0 },
.pll = PLL_28,
.tuner_type = -1,
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
},{
/* ---- card 0x58 ---------------------------------- */
.name = "Osprey 200/250", /* 0x1(A|B)-00C4-C1 */
.video_inputs = 2,
.audio_inputs = 1,
.tuner = -1,
.svhs = 1,
.muxsel = { 0, 1 },
.pll = PLL_28,
.tuner_type = -1,
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
},{
.name = "Osprey 210/220", /* 0x1(A|B)-04C0-C1 */
.video_inputs = 2,
.audio_inputs = 1,
.tuner = -1,
.svhs = 1,
.muxsel = { 2, 3 },
.pll = PLL_28,
.tuner_type = -1,
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
},{
.name = "Osprey 500", /* 500 */
.video_inputs = 2,
.audio_inputs = 1,
.tuner = -1,
.svhs = 1,
.muxsel = { 2, 3 },
.pll = PLL_28,
.tuner_type = -1,
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
},{
.name = "Osprey 540", /* 540 */
.video_inputs = 4,
.audio_inputs = 1,
.tuner = -1,
#if 0 /* TODO ... */
.svhs = OSPREY540_SVID_ANALOG,
.muxsel = { [OSPREY540_COMP_ANALOG] = 2,
[OSPREY540_SVID_ANALOG] = 3, },
#endif
.pll = PLL_28,
.tuner_type = -1,
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
#if 0 /* TODO ... */
.muxsel_hook = osprey_540_muxsel,
.picture_hook = osprey_540_set_picture,
#endif
},{
/* ---- card 0x5C ---------------------------------- */
.name = "Osprey 2000", /* 2000 */
.video_inputs = 2,
.audio_inputs = 1,
.tuner = -1,
.svhs = 1,
.muxsel = { 2, 3 },
.pll = PLL_28,
.tuner_type = -1,
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1, /* must avoid, conflicts with the bt860 */
},{
/* M G Berberich <berberic@forwiss.uni-passau.de> */
.name = "IDS Eagle",
.video_inputs = 4,
.audio_inputs = 0,
.tuner = -1,
.tuner_type = -1,
.svhs = -1,
.gpiomask = 0,
.muxsel = { 0, 1, 2, 3 },
.muxsel_hook = eagle_muxsel,
.no_msp34xx = 1,
.no_tda9875 = 1,
.pll = PLL_28,
},{
.name = "Pinnacle PCTV Sat",
.video_inputs = 2,
.audio_inputs = 0,
.svhs = 1,
.tuner = -1,
.tuner_type = -1,
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
.gpiomask = 0x01,
.audiomux = { 0, 0, 0, 0, 1 },
.muxsel = { 3, 0, 1, 2},
.needs_tvaudio = 0,
.pll = PLL_28,
.no_gpioirq = 1,
.has_dvb = 1,
},{
.name = "Formac ProTV II (bt878)",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 3,
.gpiomask = 2,
// TV, Comp1, Composite over SVID con, SVID
.muxsel = { 2, 3, 1, 1},
.audiomux = { 2, 2, 0, 0, 0 },
.pll = PLL_28,
.has_radio = 1,
.tuner_type = TUNER_PHILIPS_PAL,
/* sound routing:
GPIO=0x00,0x01,0x03: mute (?)
0x02: both TV and radio (tuner: FM1216/I)
The card has onboard audio connectors labeled "cdrom" and "board",
not soldered here, though unknown wiring.
Card lacks: external audio in, pci subsystem id.
*/
},{
/* ---- card 0x60 ---------------------------------- */
.name = "MachTV",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = -1,
.gpiomask = 7,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0, 1, 2, 3, 4},
.needs_tvaudio = 1,
.tuner_type = 5,
.pll = 1,
},{
.name = "Euresys Picolo",
.video_inputs = 3,
.audio_inputs = 0,
.tuner = -1,
.svhs = 2,
.gpiomask = 0,
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
.muxsel = { 2, 0, 1},
.pll = PLL_28,
},{
/* Luc Van Hoeylandt <luc@e-magic.be> */
.name = "ProVideo PV150", /* 0x4f */
.video_inputs = 2,
.audio_inputs = 0,
.tuner = -1,
.svhs = -1,
.gpiomask = 0,
.muxsel = { 2, 3 },
.audiomux = { 0 },
.needs_tvaudio = 0,
.no_msp34xx = 1,
.pll = PLL_28,
.tuner_type = -1,
},{
/* Hiroshi Takekawa <sian@big.or.jp> */
/* This card lacks subsystem ID */
.name = "AD-TVK503", /* 0x63 */
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x001e8007,
.muxsel = { 2, 3, 1, 0 },
/* Tuner, Radio, external, internal, off, on */
.audiomux = { 0x08, 0x0f, 0x0a, 0x08, 0x0f, 0x08 },
.needs_tvaudio = 0,
.no_msp34xx = 1,
.pll = PLL_28,
.tuner_type = 2,
.audio_hook = adtvk503_audio,
},{
/* ---- card 0x64 ---------------------------------- */
.name = "Hercules Smart TV Stereo",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x00,
.muxsel = { 2, 3, 1, 1 },
.needs_tvaudio = 1,
.no_msp34xx = 1,
.pll = PLL_28,
.tuner_type = 5,
/* Notes:
- card lacks subsystem ID
- stereo variant w/ daughter board with tda9874a @0xb0
- Audio Routing:
always from tda9874 independent of GPIO (?)
external line in: unknown
- Other chips: em78p156elp @ 0x96 (probably IR remote control)
hef4053 (instead 4052) for unknown function
*/
},{
.name = "Pace TV & Radio Card",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.muxsel = { 2, 3, 1, 1}, // Tuner, CVid, SVid, CVid over SVid connector
.gpiomask = 0,
.no_tda9875 = 1,
.no_tda7432 = 1,
.tuner_type = 1,
.has_radio = 1,
.pll = PLL_28,
/* Bt878, Bt832, FI1246 tuner; no pci subsystem id
only internal line out: (4pin header) RGGL
Radio must be decoded by msp3410d (not routed through)*/
// .digital_mode = DIGITAL_MODE_CAMERA, // todo!
},{
/* Chris Willing <chris@vislab.usyd.edu.au> */
.name = "IVC-200",
.video_inputs = 1,
.audio_inputs = 0,
.tuner = -1,
.tuner_type = -1,
.svhs = -1,
.gpiomask = 0xdf,
.muxsel = { 2 },
.pll = PLL_28,
},{
.name = "Grand X-Guard / Trust 814PCI",
.video_inputs = 16,
.audio_inputs = 0,
.tuner = -1,
.svhs = -1,
.tuner_type = 4,
.gpiomask2 = 0xff,
.muxsel = { 2,2,2,2, 3,3,3,3, 1,1,1,1, 0,0,0,0 },
.muxsel_hook = xguard_muxsel,
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
.pll = PLL_28,
},{
/* ---- card 0x68 ---------------------------------- */
.name = "Nebula Electronics DigiTV",
.video_inputs = 1,
.tuner = -1,
.svhs = -1,
.muxsel = { 2, 3, 1, 0},
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
.pll = PLL_28,
.tuner_type = -1,
.has_dvb = 1,
.no_gpioirq = 1,
},{
/* Jorge Boncompte - DTI2 <jorge@dti2.net> */
.name = "ProVideo PV143",
.video_inputs = 4,
.audio_inputs = 0,
.tuner = -1,
.svhs = -1,
.gpiomask = 0,
.muxsel = { 2, 3, 1, 0 },
.audiomux = { 0 },
.needs_tvaudio = 0,
.no_msp34xx = 1,
.pll = PLL_28,
.tuner_type = -1,
},{
/* M.Klahr@phytec.de */
.name = "PHYTEC VD-009-X1 MiniDIN (bt878)",
.video_inputs = 4,
.audio_inputs = 0,
.tuner = -1, /* card has no tuner */
.svhs = 3,
.gpiomask = 0x00,
.muxsel = { 2, 3, 1, 0},
.audiomux = { 0, 0, 0, 0, 0, 0 }, /* card has no audio */
.needs_tvaudio = 1,
.pll = PLL_28,
.tuner_type = -1,
},{
.name = "PHYTEC VD-009-X1 Combi (bt878)",
.video_inputs = 4,
.audio_inputs = 0,
.tuner = -1, /* card has no tuner */
.svhs = 3,
.gpiomask = 0x00,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 0, 0, 0, 0, 0, 0 }, /* card has no audio */
.needs_tvaudio = 1,
.pll = PLL_28,
.tuner_type = -1,
},{
/* ---- card 0x6c ---------------------------------- */
.name = "PHYTEC VD-009 MiniDIN (bt878)",
.video_inputs = 10,
.audio_inputs = 0,
.tuner = -1, /* card has no tuner */
.svhs = 9,
.gpiomask = 0x00,
.gpiomask2 = 0x03, /* gpiomask2 defines the bits used to switch audio
via the upper nibble of muxsel. here: used for
xternal video-mux */
.muxsel = { 0x02, 0x12, 0x22, 0x32, 0x03, 0x13, 0x23, 0x33, 0x01, 0x00 },
.audiomux = { 0, 0, 0, 0, 0, 0 }, /* card has no audio */
.needs_tvaudio = 1,
.pll = PLL_28,
.tuner_type = -1,
},{
.name = "PHYTEC VD-009 Combi (bt878)",
.video_inputs = 10,
.audio_inputs = 0,
.tuner = -1, /* card has no tuner */
.svhs = 9,
.gpiomask = 0x00,
.gpiomask2 = 0x03, /* gpiomask2 defines the bits used to switch audio
via the upper nibble of muxsel. here: used for
xternal video-mux */
.muxsel = { 0x02, 0x12, 0x22, 0x32, 0x03, 0x13, 0x23, 0x33, 0x01, 0x01 },
.audiomux = { 0, 0, 0, 0, 0, 0 }, /* card has no audio */
.needs_tvaudio = 1,
.pll = PLL_28,
.tuner_type = -1,
},{
.name = "IVC-100",
.video_inputs = 4,
.audio_inputs = 0,
.tuner = -1,
.tuner_type = -1,
.svhs = -1,
.gpiomask = 0xdf,
.muxsel = { 2, 3, 1, 0 },
.pll = PLL_28,
},{
/* IVC-120G - Alan Garfield <alan@fromorbit.com> */
.name = "IVC-120G",
.video_inputs = 16,
.audio_inputs = 0, /* card has no audio */
.tuner = -1, /* card has no tuner */
.tuner_type = -1,
.svhs = -1, /* card has no svhs */
.needs_tvaudio = 0,
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
.gpiomask = 0x00,
.muxsel = { 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07, 0x08,
0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f, 0x10 },
.muxsel_hook = ivc120_muxsel,
.pll = PLL_28,
},{
/* ---- card 0x70 ---------------------------------- */
.name = "pcHDTV HD-2000 TV",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.muxsel = { 2, 3, 1, 0},
.tuner_type = TUNER_PHILIPS_ATSC,
.has_dvb = 1,
},{
.name = "Twinhan DST + clones",
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
.tuner_type = TUNER_ABSENT,
.no_video = 1,
.has_dvb = 1,
},{
.name = "Winfast VC100",
.video_inputs = 3,
.audio_inputs = 0,
.svhs = 1,
.tuner = -1, // no tuner
.muxsel = { 3, 1, 1, 3}, // Vid In, SVid In, Vid over SVid in connector
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
.tuner_type = TUNER_ABSENT,
.pll = PLL_28,
},{
.name = "Teppro TEV-560/InterVision IV-560",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 3,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 1, 1, 1, 1, 0},
.needs_tvaudio = 1,
.tuner_type = TUNER_PHILIPS_PAL,
.pll = PLL_35,
},{
/* ---- card 0x74 ---------------------------------- */
.name = "SIMUS GVC1100",
.video_inputs = 4,
.audio_inputs = 0,
.tuner = -1,
.svhs = -1,
.tuner_type = -1,
.pll = PLL_28,
.muxsel = { 2, 2, 2, 2},
.gpiomask = 0x3F,
.muxsel_hook = gvc1100_muxsel,
},{
/* Carlos Silva r3pek@r3pek.homelinux.org || card 0x75 */
.name = "NGS NGSTV+",
.video_inputs = 3,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x008007,
.muxsel = {2, 3, 0, 0},
.audiomux = {0, 0, 0, 0, 0x000003, 0},
.pll = PLL_28,
.tuner_type = TUNER_PHILIPS_PAL,
.has_remote = 1,
},{
/* http://linuxmedialabs.com */
.name = "LMLBT4",
.video_inputs = 4, /* IN1,IN2,IN3,IN4 */
.audio_inputs = 0,
.tuner = -1,
.svhs = -1,
.muxsel = { 2, 3, 1, 0 },
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
.needs_tvaudio = 0,
},{
/* Helmroos Harri <harri.helmroos@pp.inet.fi> */
.name = "Tekram M205 PRO",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.tuner_type = TUNER_PHILIPS_PAL,
.svhs = 2,
.needs_tvaudio = 0,
.gpiomask = 0x68,
.muxsel = { 2, 3, 1},
.audiomux = { 0x68, 0x68, 0x61, 0x61, 0x00 },
.pll = PLL_28,
},{
/* ---- card 0x78 ---------------------------------- */
/* Javier Cendan Ares <jcendan@lycos.es> */
/* bt878 TV + FM without subsystem ID */
.name = "Conceptronic CONTVFMi",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x008007,
.muxsel = { 2, 3, 1, 1 },
.audiomux = { 0, 1, 2, 2, 3 },
.needs_tvaudio = 0,
.pll = PLL_28,
.tuner_type = TUNER_PHILIPS_PAL,
.has_remote = 1,
.has_radio = 1,
},{
/*Eric DEBIEF <debief@telemsa.com>*/
/*EURESYS Picolo Tetra : 4 Conexant Fusion 878A, no audio, video input set with analog multiplexers GPIO controled*/
/* adds picolo_tetra_muxsel(), picolo_tetra_init(), the folowing declaration strucure, and #define BTTV_PICOLO_TETRA_CHIP*/
/*0x79 in bttv.h*/
.name = "Euresys Picolo Tetra",
.video_inputs = 4,
.audio_inputs = 0,
.tuner = -1,
.svhs = -1,
.gpiomask = 0,
.gpiomask2 = 0x3C<<16,/*Set the GPIO[18]->GPIO[21] as output pin.==> drive the video inputs through analog multiplexers*/
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
.muxsel = {2,2,2,2},/*878A input is always MUX0, see above.*/
.audiomux = { 0, 0, 0, 0, 0, 0 }, /* card has no audio */
.pll = PLL_28,
.needs_tvaudio = 0,
.muxsel_hook = picolo_tetra_muxsel,/*Required as it doesn't follow the classic input selection policy*/
},{
/* Spirit TV Tuner from http://spiritmodems.com.au */
/* Stafford Goodsell <surge@goliath.homeunix.org> */
.name = "Spirit TV Tuner",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x0000000f,
.muxsel = { 2, 1, 1 },
.audiomux = { 0x02, 0x00, 0x00, 0x00, 0x00},
.tuner_type = TUNER_TEMIC_PAL,
.no_msp34xx = 1,
.no_tda9875 = 1,
},{
/* Wolfram Joost <wojo@frokaschwei.de> */
.name = "AVerMedia AVerTV DVB-T 771",
.video_inputs = 2,
.svhs = 1,
.tuner = -1,
.tuner_type = TUNER_ABSENT,
.muxsel = { 3 , 3 },
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
.pll = PLL_28,
.has_dvb = 1,
.no_gpioirq = 1,
.has_remote = 1,
},{
/* ---- card 0x7c ---------------------------------- */
/* Matt Jesson <dvb@jesson.eclipse.co.uk> */
/* Based on the Nebula card data - added remote and new card number - BTTV_AVDVBT_761, see also ir-kbd-gpio.c */
.name = "AverMedia AverTV DVB-T 761",
.video_inputs = 2,
.tuner = -1,
.svhs = 1,
.muxsel = { 3, 1, 2, 0}, /* Comp0, S-Video, ?, ? */
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
.pll = PLL_28,
.tuner_type = -1,
.has_dvb = 1,
.no_gpioirq = 1,
.has_remote = 1,
},{
/* andre.schwarz@matrix-vision.de */
.name = "MATRIX Vision Sigma-SQ",
.video_inputs = 16,
.audio_inputs = 0,
.tuner = -1,
.svhs = -1,
.gpiomask = 0x0,
.muxsel = { 2, 2, 2, 2, 2, 2, 2, 2,
3, 3, 3, 3, 3, 3, 3, 3 },
.muxsel_hook = sigmaSQ_muxsel,
.audiomux = { 0 },
.no_msp34xx = 1,
.pll = PLL_28,
.tuner_type = -1,
},{
/* andre.schwarz@matrix-vision.de */
.name = "MATRIX Vision Sigma-SLC",
.video_inputs = 4,
.audio_inputs = 0,
.tuner = -1,
.svhs = -1,
.gpiomask = 0x0,
.muxsel = { 2, 2, 2, 2 },
.muxsel_hook = sigmaSLC_muxsel,
.audiomux = { 0 },
.no_msp34xx = 1,
.pll = PLL_28,
.tuner_type = -1,
},{
/* BTTV_APAC_VIEWCOMP */
/* Attila Kondoros <attila.kondoros@chello.hu> */
/* bt878 TV + FM 0x00000000 subsystem ID */
.name = "APAC Viewcomp 878(AMAX)",
.video_inputs = 2,
.audio_inputs = 1,
.tuner = 0,
.svhs = -1,
.gpiomask = 0xFF,
.muxsel = { 2, 3, 1, 1},
.audiomux = { 2, 0, 0, 0, 10},
.needs_tvaudio = 0,
.pll = PLL_28,
.tuner_type = TUNER_PHILIPS_PAL,
.has_remote = 1, /* miniremote works, see ir-kbd-gpio.c */
.has_radio = 1, /* not every card has radio */
},{
/* ---- card 0x80 ---------------------------------- */
/* Chris Pascoe <c.pascoe@itee.uq.edu.au> */
.name = "DVICO FusionHDTV DVB-T Lite",
.tuner = -1,
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
.pll = PLL_28,
.no_video = 1,
.has_dvb = 1,
.tuner_type = -1,
},{
/* Steven <photon38@pchome.com.tw> */
.name = "V-Gear MyVCD",
.video_inputs = 3,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.gpiomask = 0x3f,
.muxsel = {2, 3, 1, 0},
.audiomux = {0x31, 0x31, 0x31, 0x31, 0x31, 0x31},
.no_msp34xx = 1,
.pll = PLL_28,
.tuner_type = TUNER_PHILIPS_NTSC_M,
.has_radio = 0,
// .has_remote = 1,
},{
/* Rick C <cryptdragoon@gmail.com> */
.name = "Super TV Tuner",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.muxsel = { 2, 3, 1, 0},
.tuner_type = TUNER_PHILIPS_NTSC,
.gpiomask = 0x008007,
.audiomux = { 0, 0x000001,0,0, 0},
.needs_tvaudio = 1,
.has_radio = 1,
},{
/* Chris Fanning <video4linux@haydon.net> */
.name = "Tibet Systems 'Progress DVR' CS16",
.video_inputs = 16,
.audio_inputs = 0,
.tuner = -1,
.svhs = -1,
.muxsel = { 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2 },
.pll = PLL_28,
.no_msp34xx = 1,
.no_tda9875 = 1,
.no_tda7432 = 1,
.tuner_type = -1,
.muxsel_hook = tibetCS16_muxsel,
},
{
/* Bill Brack <wbrack@mmm.com.hk> */
/*
* Note that, because of the card's wiring, the "master"
* BT878A chip (i.e. the one which controls the analog switch
* and must use this card type) is the 2nd one detected. The
* other 3 chips should use card type 0x85, whose description
* follows this one. There is a EEPROM on the card (which is
* connected to the I2C of one of those other chips), but is
* not currently handled. There is also a facility for a
* "monitor", which is also not currently implemented.
*/
.name = "Kodicom 4400R (master)",
.video_inputs = 16,
.audio_inputs = 0,
.tuner = -1,
.tuner_type = -1,
.svhs = -1,
/* GPIO bits 0-9 used for analog switch:
* 00 - 03: camera selector
* 04 - 06: channel (controller) selector
* 07: data (1->on, 0->off)
* 08: strobe
* 09: reset
* bit 16 is input from sync separator for the channel
*/
.gpiomask = 0x0003ff,
.no_gpioirq = 1,
.muxsel = { 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3 },
.pll = PLL_28,
.no_msp34xx = 1,
.no_tda7432 = 1,
.no_tda9875 = 1,
.muxsel_hook = kodicom4400r_muxsel,
},
{
/* Bill Brack <wbrack@mmm.com.hk> */
/* Note that, for reasons unknown, the "master" BT878A chip (i.e. the
* one which controls the analog switch, and must use the card type)
* is the 2nd one detected. The other 3 chips should use this card
* type
*/
.name = "Kodicom 4400R (slave)",
.video_inputs = 16,
.audio_inputs = 0,
.tuner = -1,
.tuner_type = -1,
.svhs = -1,
.gpiomask = 0x010000,
.no_gpioirq = 1,
.muxsel = { 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3 },
.pll = PLL_28,
.no_msp34xx = 1,
.no_tda7432 = 1,
.no_tda9875 = 1,
.muxsel_hook = kodicom4400r_muxsel,
},
{
/* ---- card 0x86---------------------------------- */
/* Michael Henson <mhenson@clarityvi.com> */
/* Adlink RTV24 with special unlock codes */
.name = "Adlink RTV24",
.video_inputs = 4,
.audio_inputs = 1,
.tuner = 0,
.svhs = 2,
.muxsel = { 2, 3, 1, 0},
.tuner_type = -1,
.pll = PLL_28,
}};
static const unsigned int bttv_num_tvcards = ARRAY_SIZE(bttv_tvcards);
/* ----------------------------------------------------------------------- */
static unsigned char eeprom_data[256];
/*
* identify card
*/
void __devinit bttv_idcard(struct bttv *btv)
{
unsigned int gpiobits;
int i,type;
unsigned short tmp;
/* read PCI subsystem ID */
pci_read_config_word(btv->c.pci, PCI_SUBSYSTEM_ID, &tmp);
btv->cardid = tmp << 16;
pci_read_config_word(btv->c.pci, PCI_SUBSYSTEM_VENDOR_ID, &tmp);
btv->cardid |= tmp;
if (0 != btv->cardid && 0xffffffff != btv->cardid) {
/* look for the card */
for (type = -1, i = 0; cards[i].id != 0; i++)
if (cards[i].id == btv->cardid)
type = i;
if (type != -1) {
/* found it */
printk(KERN_INFO "bttv%d: detected: %s [card=%d], "
"PCI subsystem ID is %04x:%04x\n",
btv->c.nr,cards[type].name,cards[type].cardnr,
btv->cardid & 0xffff,
(btv->cardid >> 16) & 0xffff);
btv->c.type = cards[type].cardnr;
} else {
/* 404 */
printk(KERN_INFO "bttv%d: subsystem: %04x:%04x (UNKNOWN)\n",
btv->c.nr, btv->cardid & 0xffff,
(btv->cardid >> 16) & 0xffff);
printk(KERN_DEBUG "please mail id, board name and "
"the correct card= insmod option to kraxel@bytesex.org\n");
}
}
/* let the user override the autodetected type */
if (card[btv->c.nr] < bttv_num_tvcards)
btv->c.type=card[btv->c.nr];
/* print which card config we are using */
printk(KERN_INFO "bttv%d: using: %s [card=%d,%s]\n",btv->c.nr,
bttv_tvcards[btv->c.type].name, btv->c.type,
card[btv->c.nr] < bttv_num_tvcards
? "insmod option" : "autodetected");
/* overwrite gpio stuff ?? */
if (UNSET == audioall && UNSET == audiomux[0])
return;
if (UNSET != audiomux[0]) {
gpiobits = 0;
for (i = 0; i < 5; i++) {
bttv_tvcards[btv->c.type].audiomux[i] = audiomux[i];
gpiobits |= audiomux[i];
}
} else {
gpiobits = audioall;
for (i = 0; i < 5; i++) {
bttv_tvcards[btv->c.type].audiomux[i] = audioall;
}
}
bttv_tvcards[btv->c.type].gpiomask = (UNSET != gpiomask) ? gpiomask : gpiobits;
printk(KERN_INFO "bttv%d: gpio config override: mask=0x%x, mux=",
btv->c.nr,bttv_tvcards[btv->c.type].gpiomask);
for (i = 0; i < 5; i++) {
printk("%s0x%x", i ? "," : "", bttv_tvcards[btv->c.type].audiomux[i]);
}
printk("\n");
}
/*
* (most) board specific initialisations goes here
*/
/* Some Modular Technology cards have an eeprom, but no subsystem ID */
void identify_by_eeprom(struct bttv *btv, unsigned char eeprom_data[256])
{
int type = -1;
if (0 == strncmp(eeprom_data,"GET MM20xPCTV",13))
type = BTTV_MODTEC_205;
else if (0 == strncmp(eeprom_data+20,"Picolo",7))
type = BTTV_EURESYS_PICOLO;
else if (eeprom_data[0] == 0x84 && eeprom_data[2]== 0)
type = BTTV_HAUPPAUGE; /* old bt848 */
if (-1 != type) {
btv->c.type = type;
printk("bttv%d: detected by eeprom: %s [card=%d]\n",
btv->c.nr, bttv_tvcards[btv->c.type].name, btv->c.type);
}
}
static void flyvideo_gpio(struct bttv *btv)
{
int gpio,has_remote,has_radio,is_capture_only,is_lr90,has_tda9820_tda9821;
int tuner=-1,ttype;
gpio_inout(0xffffff, 0);
udelay(8); // without this we would see the 0x1800 mask
gpio = gpio_read();
/* FIXME: must restore OUR_EN ??? */
// all cards provide GPIO info, some have an additional eeprom
// LR50: GPIO coding can be found lower right CP1 .. CP9
// CP9=GPIO23 .. CP1=GPIO15; when OPEN, the corresponding GPIO reads 1.
// GPIO14-12: n.c.
// LR90: GP9=GPIO23 .. GP1=GPIO15 (right above the bt878)
// lowest 3 bytes are remote control codes (no handshake needed)
// xxxFFF: No remote control chip soldered
// xxxF00(LR26/LR50), xxxFE0(LR90): Remote control chip (LVA001 or CF45) soldered
// Note: Some bits are Audio_Mask !
ttype=(gpio&0x0f0000)>>16;
switch(ttype) {
case 0x0: tuner=2; // NTSC, e.g. TPI8NSR11P
break;
case 0x2: tuner=39;// LG NTSC (newer TAPC series) TAPC-H701P
break;
case 0x4: tuner=5; // Philips PAL TPI8PSB02P, TPI8PSB12P, TPI8PSB12D or FI1216, FM1216
break;
case 0x6: tuner=37; // LG PAL (newer TAPC series) TAPC-G702P
break;
case 0xC: tuner=3; // Philips SECAM(+PAL) FQ1216ME or FI1216MF
break;
default:
printk(KERN_INFO "bttv%d: FlyVideo_gpio: unknown tuner type.\n", btv->c.nr);
}
has_remote = gpio & 0x800000;
has_radio = gpio & 0x400000;
// unknown 0x200000;
// unknown2 0x100000;
is_capture_only = !(gpio & 0x008000); //GPIO15
has_tda9820_tda9821 = !(gpio & 0x004000);
is_lr90 = !(gpio & 0x002000); // else LR26/LR50 (LR38/LR51 f. capture only)
// gpio & 0x001000 // output bit for audio routing
if(is_capture_only)
tuner=4; // No tuner present
printk(KERN_INFO "bttv%d: FlyVideo Radio=%s RemoteControl=%s Tuner=%d gpio=0x%06x\n",
btv->c.nr, has_radio? "yes":"no ", has_remote? "yes":"no ", tuner, gpio);
printk(KERN_INFO "bttv%d: FlyVideo LR90=%s tda9821/tda9820=%s capture_only=%s\n",
btv->c.nr, is_lr90?"yes":"no ", has_tda9820_tda9821?"yes":"no ",
is_capture_only?"yes":"no ");
if(tuner!= -1) // only set if known tuner autodetected, else let insmod option through
btv->tuner_type = tuner;
btv->has_radio = has_radio;
// LR90 Audio Routing is done by 2 hef4052, so Audio_Mask has 4 bits: 0x001c80
// LR26/LR50 only has 1 hef4052, Audio_Mask 0x000c00
// Audio options: from tuner, from tda9821/tda9821(mono,stereo,sap), from tda9874, ext., mute
if(has_tda9820_tda9821) btv->audio_hook = lt9415_audio;
//todo: if(has_tda9874) btv->audio_hook = fv2000s_audio;
}
static int miro_tunermap[] = { 0,6,2,3, 4,5,6,0, 3,0,4,5, 5,2,16,1,
14,2,17,1, 4,1,4,3, 1,2,16,1, 4,4,4,4 };
static int miro_fmtuner[] = { 0,0,0,0, 0,0,0,0, 0,0,0,0, 0,0,0,1,
1,1,1,1, 1,1,1,0, 0,0,0,0, 0,1,0,0 };
static void miro_pinnacle_gpio(struct bttv *btv)
{
int id,msp,gpio;
char *info;
gpio_inout(0xffffff, 0);
gpio = gpio_read();
id = ((gpio>>10) & 63) -1;
msp = bttv_I2CRead(btv, I2C_MSP3400, "MSP34xx");
if (id < 32) {
btv->tuner_type = miro_tunermap[id];
if (0 == (gpio & 0x20)) {
btv->has_radio = 1;
if (!miro_fmtuner[id]) {
btv->has_matchbox = 1;
btv->mbox_we = (1<<6);
btv->mbox_most = (1<<7);
btv->mbox_clk = (1<<8);
btv->mbox_data = (1<<9);
btv->mbox_mask = (1<<6)|(1<<7)|(1<<8)|(1<<9);
}
} else {
btv->has_radio = 0;
}
if (-1 != msp) {
if (btv->c.type == BTTV_MIRO)
btv->c.type = BTTV_MIROPRO;
if (btv->c.type == BTTV_PINNACLE)
btv->c.type = BTTV_PINNACLEPRO;
}
printk(KERN_INFO
"bttv%d: miro: id=%d tuner=%d radio=%s stereo=%s\n",
btv->c.nr, id+1, btv->tuner_type,
!btv->has_radio ? "no" :
(btv->has_matchbox ? "matchbox" : "fmtuner"),
(-1 == msp) ? "no" : "yes");
} else {
/* new cards with microtune tuner */
id = 63 - id;
btv->has_radio = 0;
switch (id) {
case 1:
info = "PAL / mono";
break;
case 2:
info = "PAL+SECAM / stereo";
btv->has_radio = 1;
break;
case 3:
info = "NTSC / stereo";
btv->has_radio = 1;
break;
case 4:
info = "PAL+SECAM / mono";
break;
case 5:
info = "NTSC / mono";
break;
case 6:
info = "NTSC / stereo";
break;
case 7:
info = "PAL / stereo";
break;
default:
info = "oops: unknown card";
break;
}
if (-1 != msp)
btv->c.type = BTTV_PINNACLEPRO;
printk(KERN_INFO
"bttv%d: pinnacle/mt: id=%d info=\"%s\" radio=%s\n",
btv->c.nr, id, info, btv->has_radio ? "yes" : "no");
btv->tuner_type = 33;
btv->pinnacle_id = id;
}
}
/* GPIO21 L: Buffer aktiv, H: Buffer inaktiv */
#define LM1882_SYNC_DRIVE 0x200000L
static void init_ids_eagle(struct bttv *btv)
{
gpio_inout(0xffffff,0xFFFF37);
gpio_write(0x200020);
/* flash strobe inverter ?! */
gpio_write(0x200024);
/* switch sync drive off */
gpio_bits(LM1882_SYNC_DRIVE,LM1882_SYNC_DRIVE);
/* set BT848 muxel to 2 */
btaor((2)<<5, ~(2<<5), BT848_IFORM);
}
/* Muxsel helper for the IDS Eagle.
* the eagles does not use the standard muxsel-bits but
* has its own multiplexer */
static void eagle_muxsel(struct bttv *btv, unsigned int input)
{
btaor((2)<<5, ~(3<<5), BT848_IFORM);
gpio_bits(3,bttv_tvcards[btv->c.type].muxsel[input&7]);
#if 0
/* svhs */
/* wake chroma ADC */
btand(~BT848_ADC_C_SLEEP, BT848_ADC);
/* set to YC video */
btor(BT848_CONTROL_COMP, BT848_E_CONTROL);
btor(BT848_CONTROL_COMP, BT848_O_CONTROL);
#else
/* composite */
/* set chroma ADC to sleep */
btor(BT848_ADC_C_SLEEP, BT848_ADC);
/* set to composite video */
btand(~BT848_CONTROL_COMP, BT848_E_CONTROL);
btand(~BT848_CONTROL_COMP, BT848_O_CONTROL);
#endif
/* switch sync drive off */
gpio_bits(LM1882_SYNC_DRIVE,LM1882_SYNC_DRIVE);
}
static void gvc1100_muxsel(struct bttv *btv, unsigned int input)
{
static const int masks[] = {0x30, 0x01, 0x12, 0x23};
gpio_write(masks[input%4]);
}
/* LMLBT4x initialization - to allow access to GPIO bits for sensors input and
alarms output
GPIObit | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
assignment | TI | O3|INx| O2| O1|IN4|IN3|IN2|IN1| | |
IN - sensor inputs, INx - sensor inputs and TI XORed together
O1,O2,O3 - alarm outputs (relays)
OUT ENABLE 1 1 0 . 1 1 0 0 . 0 0 0 0 = 0x6C0
*/
static void init_lmlbt4x(struct bttv *btv)
{
printk(KERN_DEBUG "LMLBT4x init\n");
btwrite(0x000000, BT848_GPIO_REG_INP);
gpio_inout(0xffffff, 0x0006C0);
gpio_write(0x000000);
}
static void sigmaSQ_muxsel(struct bttv *btv, unsigned int input)
{
unsigned int inmux = input % 8;
gpio_inout( 0xf, 0xf );
gpio_bits( 0xf, inmux );
}
static void sigmaSLC_muxsel(struct bttv *btv, unsigned int input)
{
unsigned int inmux = input % 4;
gpio_inout( 3<<9, 3<<9 );
gpio_bits( 3<<9, inmux<<9 );
}
/* ----------------------------------------------------------------------- */
static void bttv_reset_audio(struct bttv *btv)
{
/*
* BT878A has a audio-reset register.
* 1. This register is an audio reset function but it is in
* function-0 (video capture) address space.
* 2. It is enough to do this once per power-up of the card.
* 3. There is a typo in the Conexant doc -- it is not at
* 0x5B, but at 0x058. (B is an odd-number, obviously a typo!).
* --//Shrikumar 030609
*/
if (btv->id != 878)
return;
if (bttv_debug)
printk("bttv%d: BT878A ARESET\n",btv->c.nr);
btwrite((1<<7), 0x058);
udelay(10);
btwrite( 0, 0x058);
}
/* initialization part one -- before registering i2c bus */
void __devinit bttv_init_card1(struct bttv *btv)
{
switch (btv->c.type) {
case BTTV_HAUPPAUGE:
case BTTV_HAUPPAUGE878:
boot_msp34xx(btv,5);
break;
case BTTV_VOODOOTV_FM:
boot_msp34xx(btv,20);
break;
case BTTV_AVERMEDIA98:
boot_msp34xx(btv,11);
break;
case BTTV_HAUPPAUGEPVR:
pvr_boot(btv);
break;
case BTTV_TWINHAN_DST:
case BTTV_AVDVBT_771:
btv->use_i2c_hw = 1;
break;
}
if (!bttv_tvcards[btv->c.type].has_dvb)
bttv_reset_audio(btv);
}
/* initialization part two -- after registering i2c bus */
void __devinit bttv_init_card2(struct bttv *btv)
{
int tda9887;
btv->tuner_type = -1;
if (BTTV_UNKNOWN == btv->c.type) {
bttv_readee(btv,eeprom_data,0xa0);
identify_by_eeprom(btv,eeprom_data);
}
switch (btv->c.type) {
case BTTV_MIRO:
case BTTV_MIROPRO:
case BTTV_PINNACLE:
case BTTV_PINNACLEPRO:
/* miro/pinnacle */
miro_pinnacle_gpio(btv);
break;
case BTTV_FLYVIDEO_98:
case BTTV_MAXI:
case BTTV_LIFE_FLYKIT:
case BTTV_FLYVIDEO:
case BTTV_TYPHOON_TVIEW:
case BTTV_CHRONOS_VS2:
case BTTV_FLYVIDEO_98FM:
case BTTV_FLYVIDEO2000:
case BTTV_FLYVIDEO98EZ:
case BTTV_CONFERENCETV:
case BTTV_LIFETEC_9415:
flyvideo_gpio(btv);
break;
case BTTV_HAUPPAUGE:
case BTTV_HAUPPAUGE878:
case BTTV_HAUPPAUGEPVR:
/* pick up some config infos from the eeprom */
bttv_readee(btv,eeprom_data,0xa0);
hauppauge_eeprom(btv);
break;
case BTTV_AVERMEDIA98:
case BTTV_AVPHONE98:
bttv_readee(btv,eeprom_data,0xa0);
avermedia_eeprom(btv);
break;
case BTTV_PXC200:
init_PXC200(btv);
break;
case BTTV_PICOLO_TETRA_CHIP:
picolo_tetra_init(btv);
break;
case BTTV_VHX:
btv->has_radio = 1;
btv->has_matchbox = 1;
btv->mbox_we = 0x20;
btv->mbox_most = 0;
btv->mbox_clk = 0x08;
btv->mbox_data = 0x10;
btv->mbox_mask = 0x38;
break;
case BTTV_VOBIS_BOOSTAR:
case BTTV_TERRATV:
terratec_active_radio_upgrade(btv);
break;
case BTTV_MAGICTVIEW061:
if (btv->cardid == 0x3002144f) {
btv->has_radio=1;
printk("bttv%d: radio detected by subsystem id (CPH05x)\n",btv->c.nr);
}
break;
case BTTV_STB2:
if (btv->cardid == 0x3060121a) {
/* Fix up entry for 3DFX VoodooTV 100,
which is an OEM STB card variant. */
btv->has_radio=0;
btv->tuner_type=TUNER_TEMIC_NTSC;
}
break;
case BTTV_OSPREY1x0:
case BTTV_OSPREY1x0_848:
case BTTV_OSPREY101_848:
case BTTV_OSPREY1x1:
case BTTV_OSPREY1x1_SVID:
case BTTV_OSPREY2xx:
case BTTV_OSPREY2x0_SVID:
case BTTV_OSPREY2x0:
case BTTV_OSPREY500:
case BTTV_OSPREY540:
case BTTV_OSPREY2000:
bttv_readee(btv,eeprom_data,0xa0);
osprey_eeprom(btv);
break;
case BTTV_IDS_EAGLE:
init_ids_eagle(btv);
break;
case BTTV_MODTEC_205:
bttv_readee(btv,eeprom_data,0xa0);
modtec_eeprom(btv);
break;
case BTTV_LMLBT4:
init_lmlbt4x(btv);
break;
case BTTV_TIBET_CS16:
tibetCS16_init(btv);
break;
case BTTV_KODICOM_4400R:
kodicom4400r_init(btv);
break;
case BTTV_ADLINK_RTV24:
init_RTV24(btv);
break;
}
/* pll configuration */
if (!(btv->id==848 && btv->revision==0x11)) {
/* defaults from card list */
if (PLL_28 == bttv_tvcards[btv->c.type].pll) {
btv->pll.pll_ifreq=28636363;
btv->pll.pll_crystal=BT848_IFORM_XT0;
}
if (PLL_35 == bttv_tvcards[btv->c.type].pll) {
btv->pll.pll_ifreq=35468950;
btv->pll.pll_crystal=BT848_IFORM_XT1;
}
/* insmod options can override */
switch (pll[btv->c.nr]) {
case 0: /* none */
btv->pll.pll_crystal = 0;
btv->pll.pll_ifreq = 0;
btv->pll.pll_ofreq = 0;
break;
case 1: /* 28 MHz */
case 28:
btv->pll.pll_ifreq = 28636363;
btv->pll.pll_ofreq = 0;
btv->pll.pll_crystal = BT848_IFORM_XT0;
break;
case 2: /* 35 MHz */
case 35:
btv->pll.pll_ifreq = 35468950;
btv->pll.pll_ofreq = 0;
btv->pll.pll_crystal = BT848_IFORM_XT1;
break;
}
}
btv->pll.pll_current = -1;
/* tuner configuration (from card list / autodetect / insmod option) */
if (UNSET != bttv_tvcards[btv->c.type].tuner_type)
if(UNSET == btv->tuner_type)
btv->tuner_type = bttv_tvcards[btv->c.type].tuner_type;
if (UNSET != tuner[btv->c.nr])
btv->tuner_type = tuner[btv->c.nr];
printk("bttv%d: using tuner=%d\n",btv->c.nr,btv->tuner_type);
if (btv->pinnacle_id != UNSET)
bttv_call_i2c_clients(btv,AUDC_CONFIG_PINNACLE,
&btv->pinnacle_id);
if (btv->tuner_type != UNSET)
bttv_call_i2c_clients(btv,TUNER_SET_TYPE,&btv->tuner_type);
btv->svhs = bttv_tvcards[btv->c.type].svhs;
if (svhs[btv->c.nr] != UNSET)
btv->svhs = svhs[btv->c.nr];
if (remote[btv->c.nr] != UNSET)
btv->has_remote = remote[btv->c.nr];
if (bttv_tvcards[btv->c.type].has_radio)
btv->has_radio=1;
if (bttv_tvcards[btv->c.type].has_remote)
btv->has_remote=1;
if (bttv_tvcards[btv->c.type].no_gpioirq)
btv->gpioirq=0;
if (bttv_tvcards[btv->c.type].audio_hook)
btv->audio_hook=bttv_tvcards[btv->c.type].audio_hook;
if (bttv_tvcards[btv->c.type].digital_mode == DIGITAL_MODE_CAMERA) {
/* detect Bt832 chip for quartzsight digital camera */
if ((bttv_I2CRead(btv, I2C_BT832_ALT1, "Bt832") >=0) ||
(bttv_I2CRead(btv, I2C_BT832_ALT2, "Bt832") >=0))
boot_bt832(btv);
}
if (!autoload)
return;
/* try to detect audio/fader chips */
if (!bttv_tvcards[btv->c.type].no_msp34xx &&
bttv_I2CRead(btv, I2C_MSP3400, "MSP34xx") >=0)
request_module("msp3400");
if (bttv_tvcards[btv->c.type].msp34xx_alt &&
bttv_I2CRead(btv, I2C_MSP3400_ALT, "MSP34xx (alternate address)") >=0)
request_module("msp3400");
if (!bttv_tvcards[btv->c.type].no_tda9875 &&
bttv_I2CRead(btv, I2C_TDA9875, "TDA9875") >=0)
request_module("tda9875");
if (!bttv_tvcards[btv->c.type].no_tda7432 &&
bttv_I2CRead(btv, I2C_TDA7432, "TDA7432") >=0)
request_module("tda7432");
if (bttv_tvcards[btv->c.type].needs_tvaudio)
request_module("tvaudio");
/* tuner modules */
tda9887 = 0;
if (btv->pinnacle_id != UNSET)
tda9887 = 1;
if (0 == tda9887 && 0 == bttv_tvcards[btv->c.type].has_dvb &&
bttv_I2CRead(btv, I2C_TDA9887, "TDA9887") >=0)
tda9887 = 1;
if((btv->tuner_type == TUNER_PHILIPS_FM1216ME_MK3) ||
(btv->tuner_type == TUNER_PHILIPS_FM1236_MK3) ||
(btv->tuner_type == TUNER_PHILIPS_FM1256_IH3) ||
tda9887)
request_module("tda9887");
if (btv->tuner_type != UNSET)
request_module("tuner");
}
/* ----------------------------------------------------------------------- */
static void modtec_eeprom(struct bttv *btv)
{
if( strncmp(&(eeprom_data[0x1e]),"Temic 4066 FY5",14) ==0) {
btv->tuner_type=TUNER_TEMIC_4066FY5_PAL_I;
printk("bttv%d: Modtec: Tuner autodetected by eeprom: %s\n",
btv->c.nr,&eeprom_data[0x1e]);
} else if (strncmp(&(eeprom_data[0x1e]),"Alps TSBB5",10) ==0) {
btv->tuner_type=TUNER_ALPS_TSBB5_PAL_I;
printk("bttv%d: Modtec: Tuner autodetected by eeprom: %s\n",
btv->c.nr,&eeprom_data[0x1e]);
} else if (strncmp(&(eeprom_data[0x1e]),"Philips FM1246",14) ==0) {
btv->tuner_type=TUNER_PHILIPS_NTSC;
printk("bttv%d: Modtec: Tuner autodetected by eeprom: %s\n",
btv->c.nr,&eeprom_data[0x1e]);
} else {
printk("bttv%d: Modtec: Unknown TunerString: %s\n",
btv->c.nr,&eeprom_data[0x1e]);
}
}
static void __devinit hauppauge_eeprom(struct bttv *btv)
{
struct tveeprom tv;
tveeprom_hauppauge_analog(&tv, eeprom_data);
btv->tuner_type = tv.tuner_type;
btv->has_radio = tv.has_radio;
}
static int terratec_active_radio_upgrade(struct bttv *btv)
{
int freq;
btv->has_radio = 1;
btv->has_matchbox = 1;
btv->mbox_we = 0x10;
btv->mbox_most = 0x20;
btv->mbox_clk = 0x08;
btv->mbox_data = 0x04;
btv->mbox_mask = 0x3c;
btv->mbox_iow = 1 << 8;
btv->mbox_ior = 1 << 9;
btv->mbox_csel = 1 << 10;
freq=88000/62.5;
tea5757_write(btv, 5 * freq + 0x358); // write 0x1ed8
if (0x1ed8 == tea5757_read(btv)) {
printk("bttv%d: Terratec Active Radio Upgrade found.\n",
btv->c.nr);
btv->has_radio = 1;
btv->has_matchbox = 1;
} else {
btv->has_radio = 0;
btv->has_matchbox = 0;
}
return 0;
}
/* ----------------------------------------------------------------------- */
/*
* minimal bootstrap for the WinTV/PVR -- upload altera firmware.
*
* The hcwamc.rbf firmware file is on the Hauppauge driver CD. Have
* a look at Pvr/pvr45xxx.EXE (self-extracting zip archive, can be
* unpacked with unzip).
*/
#define PVR_GPIO_DELAY 10
#define BTTV_ALT_DATA 0x000001
#define BTTV_ALT_DCLK 0x100000
#define BTTV_ALT_NCONFIG 0x800000
static int __devinit pvr_altera_load(struct bttv *btv, u8 *micro, u32 microlen)
{
u32 n;
u8 bits;
int i;
gpio_inout(0xffffff,BTTV_ALT_DATA|BTTV_ALT_DCLK|BTTV_ALT_NCONFIG);
gpio_write(0);
udelay(PVR_GPIO_DELAY);
gpio_write(BTTV_ALT_NCONFIG);
udelay(PVR_GPIO_DELAY);
for (n = 0; n < microlen; n++) {
bits = micro[n];
for ( i = 0 ; i < 8 ; i++ ) {
gpio_bits(BTTV_ALT_DCLK,0);
if (bits & 0x01)
gpio_bits(BTTV_ALT_DATA,BTTV_ALT_DATA);
else
gpio_bits(BTTV_ALT_DATA,0);
gpio_bits(BTTV_ALT_DCLK,BTTV_ALT_DCLK);
bits >>= 1;
}
}
gpio_bits(BTTV_ALT_DCLK,0);
udelay(PVR_GPIO_DELAY);
/* begin Altera init loop (Not necessary,but doesn't hurt) */
for (i = 0 ; i < 30 ; i++) {
gpio_bits(BTTV_ALT_DCLK,0);
gpio_bits(BTTV_ALT_DCLK,BTTV_ALT_DCLK);
}
gpio_bits(BTTV_ALT_DCLK,0);
return 0;
}
static int __devinit pvr_boot(struct bttv *btv)
{
const struct firmware *fw_entry;
int rc;
rc = request_firmware(&fw_entry, "hcwamc.rbf", &btv->c.pci->dev);
if (rc != 0) {
printk(KERN_WARNING "bttv%d: no altera firmware [via hotplug]\n",
btv->c.nr);
return rc;
}
rc = pvr_altera_load(btv, fw_entry->data, fw_entry->size);
printk(KERN_INFO "bttv%d: altera firmware upload %s\n",
btv->c.nr, (rc < 0) ? "failed" : "ok");
release_firmware(fw_entry);
return rc;
}
/* ----------------------------------------------------------------------- */
/* some osprey specific stuff */
static void __devinit osprey_eeprom(struct bttv *btv)
{
int i = 0;
unsigned char *ee = eeprom_data;
unsigned long serial = 0;
if (btv->c.type == 0) {
/* this might be an antique... check for MMAC label in eeprom */
if ((ee[0]=='M') && (ee[1]=='M') && (ee[2]=='A') && (ee[3]=='C')) {
unsigned char checksum = 0;
for (i =0; i<21; i++)
checksum += ee[i];
if (checksum != ee[21])
return;
btv->c.type = BTTV_OSPREY1x0_848;
for (i = 12; i < 21; i++)
serial *= 10, serial += ee[i] - '0';
}
} else {
unsigned short type;
int offset = 4*16;
for(; offset < 8*16; offset += 16) {
unsigned short checksum = 0;
/* verify the checksum */
for(i = 0; i<14; i++) checksum += ee[i+offset];
checksum = ~checksum; /* no idea why */
if ((((checksum>>8)&0x0FF) == ee[offset+14]) &&
((checksum & 0x0FF) == ee[offset+15])) {
break;
}
}
if (offset >= 8*16)
return;
/* found a valid descriptor */
type = (ee[offset+4]<<8) | (ee[offset+5]);
switch(type) {
/* 848 based */
case 0x0004:
btv->c.type = BTTV_OSPREY1x0_848;
break;
case 0x0005:
btv->c.type = BTTV_OSPREY101_848;
break;
/* 878 based */
case 0x0012:
case 0x0013:
btv->c.type = BTTV_OSPREY1x0;
break;
case 0x0014:
case 0x0015:
btv->c.type = BTTV_OSPREY1x1;
break;
case 0x0016:
case 0x0017:
case 0x0020:
btv->c.type = BTTV_OSPREY1x1_SVID;
break;
case 0x0018:
case 0x0019:
case 0x001E:
case 0x001F:
btv->c.type = BTTV_OSPREY2xx;
break;
case 0x001A:
case 0x001B:
btv->c.type = BTTV_OSPREY2x0_SVID;
break;
case 0x0040:
btv->c.type = BTTV_OSPREY500;
break;
case 0x0050:
case 0x0056:
btv->c.type = BTTV_OSPREY540;
/* bttv_osprey_540_init(btv); */
break;
case 0x0060:
case 0x0070:
btv->c.type = BTTV_OSPREY2x0;
//enable output on select control lines
gpio_inout(0xffffff,0x000303);
break;
default:
/* unknown...leave generic, but get serial # */
break;
}
serial = (ee[offset+6] << 24)
| (ee[offset+7] << 16)
| (ee[offset+8] << 8)
| (ee[offset+9]);
}
printk(KERN_INFO "bttv%d: osprey eeprom: card=%d name=%s serial=%ld\n",
btv->c.nr, btv->c.type, bttv_tvcards[btv->c.type].name,serial);
}
/* ----------------------------------------------------------------------- */
/* AVermedia specific stuff, from bktr_card.c */
static int tuner_0_table[] = {
TUNER_PHILIPS_NTSC, TUNER_PHILIPS_PAL /* PAL-BG*/,
TUNER_PHILIPS_PAL, TUNER_PHILIPS_PAL /* PAL-I*/,
TUNER_PHILIPS_PAL, TUNER_PHILIPS_PAL,
TUNER_PHILIPS_SECAM, TUNER_PHILIPS_SECAM,
TUNER_PHILIPS_SECAM, TUNER_PHILIPS_PAL,
TUNER_PHILIPS_FM1216ME_MK3 };
#if 0
int tuner_0_fm_table[] = {
PHILIPS_FR1236_NTSC, PHILIPS_FR1216_PAL,
PHILIPS_FR1216_PAL, PHILIPS_FR1216_PAL,
PHILIPS_FR1216_PAL, PHILIPS_FR1216_PAL,
PHILIPS_FR1236_SECAM, PHILIPS_FR1236_SECAM,
PHILIPS_FR1236_SECAM, PHILIPS_FR1216_PAL};
#endif
static int tuner_1_table[] = {
TUNER_TEMIC_NTSC, TUNER_TEMIC_PAL,
TUNER_TEMIC_PAL, TUNER_TEMIC_PAL,
TUNER_TEMIC_PAL, TUNER_TEMIC_PAL,
TUNER_TEMIC_4012FY5, TUNER_TEMIC_4012FY5, //TUNER_TEMIC_SECAM
TUNER_TEMIC_4012FY5, TUNER_TEMIC_PAL};
static void __devinit avermedia_eeprom(struct bttv *btv)
{
int tuner_make,tuner_tv_fm,tuner_format,tuner=0;
tuner_make = (eeprom_data[0x41] & 0x7);
tuner_tv_fm = (eeprom_data[0x41] & 0x18) >> 3;
tuner_format = (eeprom_data[0x42] & 0xf0) >> 4;
btv->has_remote = (eeprom_data[0x42] & 0x01);
if (tuner_make == 0 || tuner_make == 2)
if(tuner_format <=0x0a)
tuner = tuner_0_table[tuner_format];
if (tuner_make == 1)
if(tuner_format <=9)
tuner = tuner_1_table[tuner_format];
if (tuner_make == 4)
if(tuner_format == 0x09)
tuner = TUNER_LG_NTSC_NEW_TAPC; // TAPC-G702P
printk(KERN_INFO "bttv%d: Avermedia eeprom[0x%02x%02x]: tuner=",
btv->c.nr,eeprom_data[0x41],eeprom_data[0x42]);
if(tuner) {
btv->tuner_type=tuner;
printk("%d",tuner);
} else
printk("Unknown type");
printk(" radio:%s remote control:%s\n",
tuner_tv_fm ? "yes" : "no",
btv->has_remote ? "yes" : "no");
}
/* used on Voodoo TV/FM (Voodoo 200), S0 wired to 0x10000 */
void bttv_tda9880_setnorm(struct bttv *btv, int norm)
{
// fix up our card entry
if(norm==VIDEO_MODE_NTSC) {
bttv_tvcards[BTTV_VOODOOTV_FM].audiomux[0]=0x957fff;
bttv_tvcards[BTTV_VOODOOTV_FM].audiomux[4]=0x957fff;
dprintk("bttv_tda9880_setnorm to NTSC\n");
}
else {
bttv_tvcards[BTTV_VOODOOTV_FM].audiomux[0]=0x947fff;
bttv_tvcards[BTTV_VOODOOTV_FM].audiomux[4]=0x947fff;
dprintk("bttv_tda9880_setnorm to PAL\n");
}
// set GPIO according
gpio_bits(bttv_tvcards[btv->c.type].gpiomask,
bttv_tvcards[btv->c.type].audiomux[btv->audio]);
}
/*
* reset/enable the MSP on some Hauppauge cards
* Thanks to Ky<4B>sti M<>lkki (kmalkki@cc.hut.fi)!
*
* Hauppauge: pin 5
* Voodoo: pin 20
*/
static void __devinit boot_msp34xx(struct bttv *btv, int pin)
{
int mask = (1 << pin);
gpio_inout(mask,mask);
gpio_bits(mask,0);
udelay(2500);
gpio_bits(mask,mask);
if (bttv_gpio)
bttv_gpio_tracking(btv,"msp34xx");
if (bttv_verbose)
printk(KERN_INFO "bttv%d: Hauppauge/Voodoo msp34xx: reset line "
"init [%d]\n", btv->c.nr, pin);
}
static void __devinit boot_bt832(struct bttv *btv)
{
#if 0 /* not working yet */
int resetbit=0;
switch (btv->c.type) {
case BTTV_PXELVWPLTVPAK:
resetbit = 0x400000;
break;
case BTTV_MODTEC_205:
resetbit = 1<<9;
break;
default:
BUG();
}
request_module("bt832");
bttv_call_i2c_clients(btv, BT832_HEXDUMP, NULL);
printk("bttv%d: Reset Bt832 [line=0x%x]\n",btv->c.nr,resetbit);
gpio_write(0);
gpio_inout(resetbit, resetbit);
udelay(5);
gpio_bits(resetbit, resetbit);
udelay(5);
gpio_bits(resetbit, 0);
udelay(5);
// bt832 on pixelview changes from i2c 0x8a to 0x88 after
// being reset as above. So we must follow by this:
bttv_call_i2c_clients(btv, BT832_REATTACH, NULL);
#endif
}
/* ----------------------------------------------------------------------- */
/* Imagenation L-Model PXC200 Framegrabber */
/* This is basically the same procedure as
* used by Alessandro Rubini in his pxc200
* driver, but using BTTV functions */
static void __devinit init_PXC200(struct bttv *btv)
{
static int vals[] __devinitdata = { 0x08, 0x09, 0x0a, 0x0b, 0x0d, 0x0d,
0x01, 0x02, 0x03, 0x04, 0x05, 0x06,
0x00 };
unsigned int i;
int tmp;
u32 val;
/* Initialise GPIO-connevted stuff */
gpio_inout(0xffffff, (1<<13));
gpio_write(0);
udelay(3);
gpio_write(1<<13);
/* GPIO inputs are pulled up, so no need to drive
* reset pin any longer */
gpio_bits(0xffffff, 0);
if (bttv_gpio)
bttv_gpio_tracking(btv,"pxc200");
/* we could/should try and reset/control the AD pots? but
right now we simply turned off the crushing. Without
this the AGC drifts drifts
remember the EN is reverse logic -->
setting BT848_ADC_AGC_EN disable the AGC
tboult@eecs.lehigh.edu
*/
btwrite(BT848_ADC_RESERVED|BT848_ADC_AGC_EN, BT848_ADC);
/* Initialise MAX517 DAC */
printk(KERN_INFO "Setting DAC reference voltage level ...\n");
bttv_I2CWrite(btv,0x5E,0,0x80,1);
/* Initialise 12C508 PIC */
/* The I2CWrite and I2CRead commmands are actually to the
* same chips - but the R/W bit is included in the address
* argument so the numbers are different */
printk(KERN_INFO "Initialising 12C508 PIC chip ...\n");
/* First of all, enable the clock line. This is used in the PXC200-F */
val = btread(BT848_GPIO_DMA_CTL);
val |= BT848_GPIO_DMA_CTL_GPCLKMODE;
btwrite(val, BT848_GPIO_DMA_CTL);
/* Then, push to 0 the reset pin long enough to reset the *
* device same as above for the reset line, but not the same
* value sent to the GPIO-connected stuff
* which one is the good one? */
gpio_inout(0xffffff,(1<<2));
gpio_write(0);
udelay(10);
gpio_write(1<<2);
for (i = 0; i < ARRAY_SIZE(vals); i++) {
tmp=bttv_I2CWrite(btv,0x1E,0,vals[i],1);
if (tmp != -1) {
printk(KERN_INFO
"I2C Write(%2.2x) = %i\nI2C Read () = %2.2x\n\n",
vals[i],tmp,bttv_I2CRead(btv,0x1F,NULL));
}
}
printk(KERN_INFO "PXC200 Initialised.\n");
}
/* ----------------------------------------------------------------------- */
/*
* The Adlink RTV-24 (aka Angelo) has some special initialisation to unlock
* it. This apparently involves the following procedure for each 878 chip:
*
* 1) write 0x00C3FEFF to the GPIO_OUT_EN register
*
* 2) write to GPIO_DATA
* - 0x0E
* - sleep 1ms
* - 0x10 + 0x0E
* - sleep 10ms
* - 0x0E
* read from GPIO_DATA into buf (uint_32)
* - if ( data>>18 & 0x01 != 0) || ( buf>>19 & 0x01 != 1 )
* error. ERROR_CPLD_Check_Failed stop.
*
* 3) write to GPIO_DATA
* - write 0x4400 + 0x0E
* - sleep 10ms
* - write 0x4410 + 0x0E
* - sleep 1ms
* - write 0x0E
* read from GPIO_DATA into buf (uint_32)
* - if ( buf>>18 & 0x01 ) || ( buf>>19 && 0x01 != 0 )
* error. ERROR_CPLD_Check_Failed.
*/
/* ----------------------------------------------------------------------- */
void init_RTV24(struct bttv *btv)
{
u32 dataread;
const long watchdog_value = 0x0E;
printk(KERN_INFO "bttv%d: Adlink RTV-24 initialisation in progress\n",
btv->c.nr);
btwrite(0x00c3feff, BT848_GPIO_OUT_EN);
btwrite(0 + watchdog_value, BT848_GPIO_DATA);
msleep(1);
btwrite(0x10 + watchdog_value, BT848_GPIO_DATA);
msleep( 10 );
btwrite(0 + watchdog_value, BT848_GPIO_DATA);
dataread = btread(BT848_GPIO_DATA);
if (((dataread >> 18) & 0x01) != 0 || ((dataread >> 19) & 0x01) != 1) {
printk(KERN_INFO "bttv%d: Adlink RTV-24 initialisation(1) "
"ERROR_CPLD_Check_Failed (read %d)\n",
btv->c.nr, dataread);
}
btwrite(0x4400 + watchdog_value, BT848_GPIO_DATA);
msleep(10);
btwrite(0x4410 + watchdog_value, BT848_GPIO_DATA);
msleep(1);
btwrite(watchdog_value, BT848_GPIO_DATA);
msleep(1);
dataread = btread(BT848_GPIO_DATA);
if (((dataread >> 18) & 0x01) != 0 || ((dataread >> 19) & 0x01) != 0) {
printk(KERN_INFO "bttv%d: Adlink RTV-24 initialisation(2) "
"ERROR_CPLD_Check_Failed (read %d)\n",
btv->c.nr, dataread);
return;
}
printk(KERN_INFO "bttv%d: Adlink RTV-24 initialisation complete.\n",
btv->c.nr);
}
/* ----------------------------------------------------------------------- */
/* Miro Pro radio stuff -- the tea5757 is connected to some GPIO ports */
/*
* Copyright (c) 1999 Csaba Halasz <qgehali@uni-miskolc.hu>
* This code is placed under the terms of the GNU General Public License
*
* Brutally hacked by Dan Sheridan <dan.sheridan@contact.org.uk> djs52 8/3/00
*/
static void bus_low(struct bttv *btv, int bit)
{
if (btv->mbox_ior) {
gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel,
btv->mbox_ior | btv->mbox_iow | btv->mbox_csel);
udelay(5);
}
gpio_bits(bit,0);
udelay(5);
if (btv->mbox_ior) {
gpio_bits(btv->mbox_iow | btv->mbox_csel, 0);
udelay(5);
}
}
static void bus_high(struct bttv *btv, int bit)
{
if (btv->mbox_ior) {
gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel,
btv->mbox_ior | btv->mbox_iow | btv->mbox_csel);
udelay(5);
}
gpio_bits(bit,bit);
udelay(5);
if (btv->mbox_ior) {
gpio_bits(btv->mbox_iow | btv->mbox_csel, 0);
udelay(5);
}
}
static int bus_in(struct bttv *btv, int bit)
{
if (btv->mbox_ior) {
gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel,
btv->mbox_ior | btv->mbox_iow | btv->mbox_csel);
udelay(5);
gpio_bits(btv->mbox_iow | btv->mbox_csel, 0);
udelay(5);
}
return gpio_read() & (bit);
}
/* TEA5757 register bits */
#define TEA_FREQ 0:14
#define TEA_BUFFER 15:15
#define TEA_SIGNAL_STRENGTH 16:17
#define TEA_PORT1 18:18
#define TEA_PORT0 19:19
#define TEA_BAND 20:21
#define TEA_BAND_FM 0
#define TEA_BAND_MW 1
#define TEA_BAND_LW 2
#define TEA_BAND_SW 3
#define TEA_MONO 22:22
#define TEA_ALLOW_STEREO 0
#define TEA_FORCE_MONO 1
#define TEA_SEARCH_DIRECTION 23:23
#define TEA_SEARCH_DOWN 0
#define TEA_SEARCH_UP 1
#define TEA_STATUS 24:24
#define TEA_STATUS_TUNED 0
#define TEA_STATUS_SEARCHING 1
/* Low-level stuff */
static int tea5757_read(struct bttv *btv)
{
unsigned long timeout;
int value = 0;
int i;
/* better safe than sorry */
gpio_inout(btv->mbox_mask, btv->mbox_clk | btv->mbox_we);
if (btv->mbox_ior) {
gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel,
btv->mbox_ior | btv->mbox_iow | btv->mbox_csel);
udelay(5);
}
if (bttv_gpio)
bttv_gpio_tracking(btv,"tea5757 read");
bus_low(btv,btv->mbox_we);
bus_low(btv,btv->mbox_clk);
udelay(10);
timeout= jiffies + HZ;
// wait for DATA line to go low; error if it doesn't
while (bus_in(btv,btv->mbox_data) && time_before(jiffies, timeout))
schedule();
if (bus_in(btv,btv->mbox_data)) {
printk(KERN_WARNING "bttv%d: tea5757: read timeout\n",btv->c.nr);
return -1;
}
dprintk("bttv%d: tea5757:",btv->c.nr);
for(i = 0; i < 24; i++)
{
udelay(5);
bus_high(btv,btv->mbox_clk);
udelay(5);
dprintk("%c",(bus_in(btv,btv->mbox_most) == 0)?'T':'-');
bus_low(btv,btv->mbox_clk);
value <<= 1;
value |= (bus_in(btv,btv->mbox_data) == 0)?0:1; /* MSB first */
dprintk("%c", (bus_in(btv,btv->mbox_most) == 0)?'S':'M');
}
dprintk("\nbttv%d: tea5757: read 0x%X\n", btv->c.nr, value);
return value;
}
static int tea5757_write(struct bttv *btv, int value)
{
int i;
int reg = value;
gpio_inout(btv->mbox_mask, btv->mbox_clk | btv->mbox_we | btv->mbox_data);
if (btv->mbox_ior) {
gpio_bits(btv->mbox_ior | btv->mbox_iow | btv->mbox_csel,
btv->mbox_ior | btv->mbox_iow | btv->mbox_csel);
udelay(5);
}
if (bttv_gpio)
bttv_gpio_tracking(btv,"tea5757 write");
dprintk("bttv%d: tea5757: write 0x%X\n", btv->c.nr, value);
bus_low(btv,btv->mbox_clk);
bus_high(btv,btv->mbox_we);
for(i = 0; i < 25; i++)
{
if (reg & 0x1000000)
bus_high(btv,btv->mbox_data);
else
bus_low(btv,btv->mbox_data);
reg <<= 1;
bus_high(btv,btv->mbox_clk);
udelay(10);
bus_low(btv,btv->mbox_clk);
udelay(10);
}
bus_low(btv,btv->mbox_we); /* unmute !!! */
return 0;
}
void tea5757_set_freq(struct bttv *btv, unsigned short freq)
{
dprintk("tea5757_set_freq %d\n",freq);
tea5757_write(btv, 5 * freq + 0x358); /* add 10.7MHz (see docs) */
#if 0
/* breaks Miro PCTV */
value = tea5757_read(btv);
dprintk("bttv%d: tea5757 readback=0x%x\n",btv->c.nr,value);
#endif
}
/* ----------------------------------------------------------------------- */
/* winview */
void winview_audio(struct bttv *btv, struct video_audio *v, int set)
{
/* PT2254A programming Jon Tombs, jon@gte.esi.us.es */
int bits_out, loops, vol, data;
if (!set) {
/* Fixed by Leandro Lucarella <luca@linuxmendoza.org.ar (07/31/01) */
v->flags |= VIDEO_AUDIO_VOLUME;
return;
}
/* 32 levels logarithmic */
vol = 32 - ((v->volume>>11));
/* units */
bits_out = (PT2254_DBS_IN_2>>(vol%5));
/* tens */
bits_out |= (PT2254_DBS_IN_10>>(vol/5));
bits_out |= PT2254_L_CHANNEL | PT2254_R_CHANNEL;
data = gpio_read();
data &= ~(WINVIEW_PT2254_CLK| WINVIEW_PT2254_DATA|
WINVIEW_PT2254_STROBE);
for (loops = 17; loops >= 0 ; loops--) {
if (bits_out & (1<<loops))
data |= WINVIEW_PT2254_DATA;
else
data &= ~WINVIEW_PT2254_DATA;
gpio_write(data);
udelay(5);
data |= WINVIEW_PT2254_CLK;
gpio_write(data);
udelay(5);
data &= ~WINVIEW_PT2254_CLK;
gpio_write(data);
}
data |= WINVIEW_PT2254_STROBE;
data &= ~WINVIEW_PT2254_DATA;
gpio_write(data);
udelay(10);
data &= ~WINVIEW_PT2254_STROBE;
gpio_write(data);
}
/* ----------------------------------------------------------------------- */
/* mono/stereo control for various cards (which don't use i2c chips but */
/* connect something to the GPIO pins */
static void
gvbctv3pci_audio(struct bttv *btv, struct video_audio *v, int set)
{
unsigned int con = 0;
if (set) {
gpio_inout(0x300, 0x300);
if (v->mode & VIDEO_SOUND_LANG1)
con = 0x000;
if (v->mode & VIDEO_SOUND_LANG2)
con = 0x300;
if (v->mode & VIDEO_SOUND_STEREO)
con = 0x200;
// if (v->mode & VIDEO_SOUND_MONO)
// con = 0x100;
gpio_bits(0x300, con);
} else {
v->mode = VIDEO_SOUND_STEREO |
VIDEO_SOUND_LANG1 | VIDEO_SOUND_LANG2;
}
}
static void
gvbctv5pci_audio(struct bttv *btv, struct video_audio *v, int set)
{
unsigned int val, con;
#if BTTV_VERSION_CODE > KERNEL_VERSION(0,8,0)
if (btv->radio_user)
return;
#else
if (btv->radio)
return;
#endif
val = gpio_read();
if (set) {
con = 0x000;
if (v->mode & VIDEO_SOUND_LANG2) {
if (v->mode & VIDEO_SOUND_LANG1) {
/* LANG1 + LANG2 */
con = 0x100;
}
else {
/* LANG2 */
con = 0x300;
}
}
if (con != (val & 0x300)) {
gpio_bits(0x300, con);
if (bttv_gpio)
bttv_gpio_tracking(btv,"gvbctv5pci");
}
} else {
switch (val & 0x70) {
case 0x10:
v->mode = VIDEO_SOUND_LANG1 | VIDEO_SOUND_LANG2;
break;
case 0x30:
v->mode = VIDEO_SOUND_LANG2;
break;
case 0x50:
v->mode = VIDEO_SOUND_LANG1;
break;
case 0x60:
v->mode = VIDEO_SOUND_STEREO;
break;
case 0x70:
v->mode = VIDEO_SOUND_MONO;
break;
default:
v->mode = VIDEO_SOUND_MONO | VIDEO_SOUND_STEREO |
VIDEO_SOUND_LANG1 | VIDEO_SOUND_LANG2;
}
}
}
/*
* Mario Medina Nussbaum <medisoft@alohabbs.org.mx>
* I discover that on BT848_GPIO_DATA address a byte 0xcce enable stereo,
* 0xdde enables mono and 0xccd enables sap
*
* Petr Vandrovec <VANDROVE@vc.cvut.cz>
* P.S.: At least mask in line above is wrong - GPIO pins 3,2 select
* input/output sound connection, so both must be set for output mode.
*
* Looks like it's needed only for the "tvphone", the "tvphone 98"
* handles this with a tda9840
*
*/
static void
avermedia_tvphone_audio(struct bttv *btv, struct video_audio *v, int set)
{
int val = 0;
if (set) {
if (v->mode & VIDEO_SOUND_LANG2) /* SAP */
val = 0x02;
if (v->mode & VIDEO_SOUND_STEREO)
val = 0x01;
if (val) {
gpio_bits(0x03,val);
if (bttv_gpio)
bttv_gpio_tracking(btv,"avermedia");
}
} else {
v->mode = VIDEO_SOUND_MONO | VIDEO_SOUND_STEREO |
VIDEO_SOUND_LANG1;
return;
}
}
static void
avermedia_tv_stereo_audio(struct bttv *btv, struct video_audio *v, int set)
{
int val = 0;
if (set) {
if (v->mode & VIDEO_SOUND_LANG2) /* SAP */
val = 0x01;
if (v->mode & VIDEO_SOUND_STEREO) /* STEREO */
val = 0x02;
btaor(val, ~0x03, BT848_GPIO_DATA);
if (bttv_gpio)
bttv_gpio_tracking(btv,"avermedia");
} else {
v->mode = VIDEO_SOUND_MONO | VIDEO_SOUND_STEREO |
VIDEO_SOUND_LANG1 | VIDEO_SOUND_LANG2;
return;
}
}
/* Lifetec 9415 handling */
static void
lt9415_audio(struct bttv *btv, struct video_audio *v, int set)
{
int val = 0;
if (gpio_read() & 0x4000) {
v->mode = VIDEO_SOUND_MONO;
return;
}
if (set) {
if (v->mode & VIDEO_SOUND_LANG2) /* A2 SAP */
val = 0x0080;
if (v->mode & VIDEO_SOUND_STEREO) /* A2 stereo */
val = 0x0880;
if ((v->mode & VIDEO_SOUND_LANG1) ||
(v->mode & VIDEO_SOUND_MONO))
val = 0;
gpio_bits(0x0880, val);
if (bttv_gpio)
bttv_gpio_tracking(btv,"lt9415");
} else {
/* autodetect doesn't work with this card :-( */
v->mode = VIDEO_SOUND_MONO | VIDEO_SOUND_STEREO |
VIDEO_SOUND_LANG1 | VIDEO_SOUND_LANG2;
return;
}
}
// TDA9821 on TerraTV+ Bt848, Bt878
static void
terratv_audio(struct bttv *btv, struct video_audio *v, int set)
{
unsigned int con = 0;
if (set) {
gpio_inout(0x180000,0x180000);
if (v->mode & VIDEO_SOUND_LANG2)
con = 0x080000;
if (v->mode & VIDEO_SOUND_STEREO)
con = 0x180000;
gpio_bits(0x180000, con);
if (bttv_gpio)
bttv_gpio_tracking(btv,"terratv");
} else {
v->mode = VIDEO_SOUND_MONO | VIDEO_SOUND_STEREO |
VIDEO_SOUND_LANG1 | VIDEO_SOUND_LANG2;
}
}
static void
winfast2000_audio(struct bttv *btv, struct video_audio *v, int set)
{
unsigned long val = 0;
if (set) {
/*btor (0xc32000, BT848_GPIO_OUT_EN);*/
if (v->mode & VIDEO_SOUND_MONO) /* Mono */
val = 0x420000;
if (v->mode & VIDEO_SOUND_LANG1) /* Mono */
val = 0x420000;
if (v->mode & VIDEO_SOUND_LANG2) /* SAP */
val = 0x410000;
if (v->mode & VIDEO_SOUND_STEREO) /* Stereo */
val = 0x020000;
if (val) {
gpio_bits(0x430000, val);
if (bttv_gpio)
bttv_gpio_tracking(btv,"winfast2000");
}
} else {
v->mode = VIDEO_SOUND_MONO | VIDEO_SOUND_STEREO |
VIDEO_SOUND_LANG1 | VIDEO_SOUND_LANG2;
}
}
/*
* Dariusz Kowalewski <darekk@automex.pl>
* sound control for Prolink PV-BT878P+9B (PixelView PlayTV Pro FM+NICAM
* revision 9B has on-board TDA9874A sound decoder).
*
* Note: There are card variants without tda9874a. Forcing the "stereo sound route"
* will mute this cards.
*/
static void
pvbt878p9b_audio(struct bttv *btv, struct video_audio *v, int set)
{
unsigned int val = 0;
#if BTTV_VERSION_CODE > KERNEL_VERSION(0,8,0)
if (btv->radio_user)
return;
#else
if (btv->radio)
return;
#endif
if (set) {
if (v->mode & VIDEO_SOUND_MONO) {
val = 0x01;
}
if ((v->mode & (VIDEO_SOUND_LANG1 | VIDEO_SOUND_LANG2))
|| (v->mode & VIDEO_SOUND_STEREO)) {
val = 0x02;
}
if (val) {
gpio_bits(0x03,val);
if (bttv_gpio)
bttv_gpio_tracking(btv,"pvbt878p9b");
}
} else {
v->mode = VIDEO_SOUND_MONO | VIDEO_SOUND_STEREO |
VIDEO_SOUND_LANG1 | VIDEO_SOUND_LANG2;
}
}
/*
* Dariusz Kowalewski <darekk@automex.pl>
* sound control for FlyVideo 2000S (with tda9874 decoder)
* based on pvbt878p9b_audio() - this is not tested, please fix!!!
*/
static void
fv2000s_audio(struct bttv *btv, struct video_audio *v, int set)
{
unsigned int val = 0xffff;
#if BTTV_VERSION_CODE > KERNEL_VERSION(0,8,0)
if (btv->radio_user)
return;
#else
if (btv->radio)
return;
#endif
if (set) {
if (v->mode & VIDEO_SOUND_MONO) {
val = 0x0000;
}
if ((v->mode & (VIDEO_SOUND_LANG1 | VIDEO_SOUND_LANG2))
|| (v->mode & VIDEO_SOUND_STEREO)) {
val = 0x1080; //-dk-???: 0x0880, 0x0080, 0x1800 ...
}
if (val != 0xffff) {
gpio_bits(0x1800, val);
if (bttv_gpio)
bttv_gpio_tracking(btv,"fv2000s");
}
} else {
v->mode = VIDEO_SOUND_MONO | VIDEO_SOUND_STEREO |
VIDEO_SOUND_LANG1 | VIDEO_SOUND_LANG2;
}
}
/*
* sound control for Canopus WinDVR PCI
* Masaki Suzuki <masaki@btree.org>
*/
static void
windvr_audio(struct bttv *btv, struct video_audio *v, int set)
{
unsigned long val = 0;
if (set) {
if (v->mode & VIDEO_SOUND_MONO)
val = 0x040000;
if (v->mode & VIDEO_SOUND_LANG1)
val = 0;
if (v->mode & VIDEO_SOUND_LANG2)
val = 0x100000;
if (v->mode & VIDEO_SOUND_STEREO)
val = 0;
if (val) {
gpio_bits(0x140000, val);
if (bttv_gpio)
bttv_gpio_tracking(btv,"windvr");
}
} else {
v->mode = VIDEO_SOUND_MONO | VIDEO_SOUND_STEREO |
VIDEO_SOUND_LANG1 | VIDEO_SOUND_LANG2;
}
}
/*
* sound control for AD-TVK503
* Hiroshi Takekawa <sian@big.or.jp>
*/
static void
adtvk503_audio(struct bttv *btv, struct video_audio *v, int set)
{
unsigned int con = 0xffffff;
//btaor(0x1e0000, ~0x1e0000, BT848_GPIO_OUT_EN);
if (set) {
//btor(***, BT848_GPIO_OUT_EN);
if (v->mode & VIDEO_SOUND_LANG1)
con = 0x00000000;
if (v->mode & VIDEO_SOUND_LANG2)
con = 0x00180000;
if (v->mode & VIDEO_SOUND_STEREO)
con = 0x00000000;
if (v->mode & VIDEO_SOUND_MONO)
con = 0x00060000;
if (con != 0xffffff) {
gpio_bits(0x1e0000,con);
if (bttv_gpio)
bttv_gpio_tracking(btv, "adtvk503");
}
} else {
v->mode = VIDEO_SOUND_MONO | VIDEO_SOUND_STEREO |
VIDEO_SOUND_LANG1 | VIDEO_SOUND_LANG2;
}
}
/* RemoteVision MX (rv605) muxsel helper [Miguel Freitas]
*
* This is needed because rv605 don't use a normal multiplex, but a crosspoint
* switch instead (CD22M3494E). This IC can have multiple active connections
* between Xn (input) and Yn (output) pins. We need to clear any existing
* connection prior to establish a new one, pulsing the STROBE pin.
*
* The board hardwire Y0 (xpoint) to MUX1 and MUXOUT to Yin.
* GPIO pins are wired as:
* GPIO[0:3] - AX[0:3] (xpoint) - P1[0:3] (microcontroler)
* GPIO[4:6] - AY[0:2] (xpoint) - P1[4:6] (microcontroler)
* GPIO[7] - DATA (xpoint) - P1[7] (microcontroler)
* GPIO[8] - - P3[5] (microcontroler)
* GPIO[9] - RESET (xpoint) - P3[6] (microcontroler)
* GPIO[10] - STROBE (xpoint) - P3[7] (microcontroler)
* GPINTR - - P3[4] (microcontroler)
*
* The microcontroler is a 80C32 like. It should be possible to change xpoint
* configuration either directly (as we are doing) or using the microcontroler
* which is also wired to I2C interface. I have no further info on the
* microcontroler features, one would need to disassembly the firmware.
* note: the vendor refused to give any information on this product, all
* that stuff was found using a multimeter! :)
*/
static void rv605_muxsel(struct bttv *btv, unsigned int input)
{
/* reset all conections */
gpio_bits(0x200,0x200);
mdelay(1);
gpio_bits(0x200,0x000);
mdelay(1);
/* create a new conection */
gpio_bits(0x480,0x080);
gpio_bits(0x480,0x480);
mdelay(1);
gpio_bits(0x480,0x080);
mdelay(1);
}
/* Tibet Systems 'Progress DVR' CS16 muxsel helper [Chris Fanning]
*
* The CS16 (available on eBay cheap) is a PCI board with four Fusion
* 878A chips, a PCI bridge, an Atmel microcontroller, four sync seperator
* chips, ten eight input analog multiplexors, a not chip and a few
* other components.
*
* 16 inputs on a secondary bracket are provided and can be selected
* from each of the four capture chips. Two of the eight input
* multiplexors are used to select from any of the 16 input signals.
*
* Unsupported hardware capabilities:
* . A video output monitor on the secondary bracket can be selected from
* one of the 878A chips.
* . Another passthrough but I haven't spent any time investigating it.
* . Digital I/O (logic level connected to GPIO) is available from an
* onboard header.
*
* The on chip input mux should always be set to 2.
* GPIO[16:19] - Video input selection
* GPIO[0:3] - Video output monitor select (only available from one 878A)
* GPIO[?:?] - Digital I/O.
*
* There is an ATMEL microcontroller with an 8031 core on board. I have not
* determined what function (if any) it provides. With the microcontroller
* and sync seperator chips a guess is that it might have to do with video
* switching and maybe some digital I/O.
*/
static void tibetCS16_muxsel(struct bttv *btv, unsigned int input)
{
/* video mux */
gpio_bits(0x0f0000, input << 16);
}
static void tibetCS16_init(struct bttv *btv)
{
/* enable gpio bits, mask obtained via btSpy */
gpio_inout(0xffffff, 0x0f7fff);
gpio_write(0x0f7fff);
}
/*
* The following routines for the Kodicom-4400r get a little mind-twisting.
* There is a "master" controller and three "slave" controllers, together
* an analog switch which connects any of 16 cameras to any of the BT87A's.
* The analog switch is controlled by the "master", but the detection order
* of the four BT878A chips is in an order which I just don't understand.
* The "master" is actually the second controller to be detected. The
* logic on the board uses logical numbers for the 4 controlers, but
* those numbers are different from the detection sequence. When working
* with the analog switch, we need to "map" from the detection sequence
* over to the board's logical controller number. This mapping sequence
* is {3, 0, 2, 1}, i.e. the first controller to be detected is logical
* unit 3, the second (which is the master) is logical unit 0, etc.
* We need to maintain the status of the analog switch (which of the 16
* cameras is connected to which of the 4 controllers). Rather than
* add to the bttv structure for this, we use the data reserved for
* the mbox (unused for this card type).
*/
/*
* First a routine to set the analog switch, which controls which camera
* is routed to which controller. The switch comprises an X-address
* (gpio bits 0-3, representing the camera, ranging from 0-15), and a
* Y-address (gpio bits 4-6, representing the controller, ranging from 0-3).
* A data value (gpio bit 7) of '1' enables the switch, and '0' disables
* the switch. A STROBE bit (gpio bit 8) latches the data value into the
* specified address. The idea is to set the address and data, then bring
* STROBE high, and finally bring STROBE back to low.
*/
static void kodicom4400r_write(struct bttv *btv,
unsigned char xaddr,
unsigned char yaddr,
unsigned char data) {
unsigned int udata;
udata = (data << 7) | ((yaddr&3) << 4) | (xaddr&0xf);
gpio_bits(0x1ff, udata); /* write ADDR and DAT */
gpio_bits(0x1ff, udata | (1 << 8)); /* strobe high */
gpio_bits(0x1ff, udata); /* strobe low */
}
/*
* Next the mux select. Both the "master" and "slave" 'cards' (controllers)
* use this routine. The routine finds the "master" for the card, maps
* the controller number from the detected position over to the logical
* number, writes the appropriate data to the analog switch, and housekeeps
* the local copy of the switch information. The parameter 'input' is the
* requested camera number (0 - 15).
*/
static void kodicom4400r_muxsel(struct bttv *btv, unsigned int input)
{
char *sw_status;
int xaddr, yaddr;
struct bttv *mctlr;
static unsigned char map[4] = {3, 0, 2, 1};
mctlr = master[btv->c.nr];
if (mctlr == NULL) { /* ignore if master not yet detected */
return;
}
yaddr = (btv->c.nr - mctlr->c.nr + 1) & 3; /* the '&' is for safety */
yaddr = map[yaddr];
sw_status = (char *)(&mctlr->mbox_we);
xaddr = input & 0xf;
/* Check if the controller/camera pair has changed, else ignore */
if (sw_status[yaddr] != xaddr)
{
/* "open" the old switch, "close" the new one, save the new */
kodicom4400r_write(mctlr, sw_status[yaddr], yaddr, 0);
sw_status[yaddr] = xaddr;
kodicom4400r_write(mctlr, xaddr, yaddr, 1);
}
}
/*
* During initialisation, we need to reset the analog switch. We
* also preset the switch to map the 4 connectors on the card to the
* *user's* (see above description of kodicom4400r_muxsel) channels
* 0 through 3
*/
static void kodicom4400r_init(struct bttv *btv)
{
char *sw_status = (char *)(&btv->mbox_we);
int ix;
gpio_inout(0x0003ff, 0x0003ff);
gpio_write(1 << 9); /* reset MUX */
gpio_write(0);
/* Preset camera 0 to the 4 controllers */
for (ix=0; ix<4; ix++) {
sw_status[ix] = ix;
kodicom4400r_write(btv, ix, ix, 1);
}
/*
* Since this is the "master", we need to set up the
* other three controller chips' pointers to this structure
* for later use in the muxsel routine.
*/
if ((btv->c.nr<1) || (btv->c.nr>BTTV_MAX-3))
return;
master[btv->c.nr-1] = btv;
master[btv->c.nr] = btv;
master[btv->c.nr+1] = btv;
master[btv->c.nr+2] = btv;
}
// The Grandtec X-Guard framegrabber card uses two Dual 4-channel
// video multiplexers to provide up to 16 video inputs. These
// multiplexers are controlled by the lower 8 GPIO pins of the
// bt878. The multiplexers probably Pericom PI5V331Q or similar.
// xxx0 is pin xxx of multiplexer U5,
// yyy1 is pin yyy of multiplexer U2
#define ENA0 0x01
#define ENB0 0x02
#define ENA1 0x04
#define ENB1 0x08
#define IN10 0x10
#define IN00 0x20
#define IN11 0x40
#define IN01 0x80
static void xguard_muxsel(struct bttv *btv, unsigned int input)
{
static const int masks[] = {
ENB0, ENB0|IN00, ENB0|IN10, ENB0|IN00|IN10,
ENA0, ENA0|IN00, ENA0|IN10, ENA0|IN00|IN10,
ENB1, ENB1|IN01, ENB1|IN11, ENB1|IN01|IN11,
ENA1, ENA1|IN01, ENA1|IN11, ENA1|IN01|IN11,
};
gpio_write(masks[input%16]);
}
static void picolo_tetra_init(struct bttv *btv)
{
/*This is the video input redirection fonctionality : I DID NOT USED IT. */
btwrite (0x08<<16,BT848_GPIO_DATA);/*GPIO[19] [==> 4053 B+C] set to 1 */
btwrite (0x04<<16,BT848_GPIO_DATA);/*GPIO[18] [==> 4053 A] set to 1*/
}
static void picolo_tetra_muxsel (struct bttv* btv, unsigned int input)
{
dprintk (KERN_DEBUG "bttv%d : picolo_tetra_muxsel => input = %d\n",btv->c.nr,input);
/*Just set the right path in the analog multiplexers : channel 1 -> 4 ==> Analog Mux ==> MUX0*/
/*GPIO[20]&GPIO[21] used to choose the right input*/
btwrite (input<<20,BT848_GPIO_DATA);
}
/*
* ivc120_muxsel [Added by Alan Garfield <alan@fromorbit.com>]
*
* The IVC120G security card has 4 i2c controlled TDA8540 matrix
* swichers to provide 16 channels to MUX0. The TDA8540's have
* 4 indepedant outputs and as such the IVC120G also has the
* optional "Monitor Out" bus. This allows the card to be looking
* at one input while the monitor is looking at another.
*
* Since I've couldn't be bothered figuring out how to add an
* independant muxsel for the monitor bus, I've just set it to
* whatever the card is looking at.
*
* OUT0 of the TDA8540's is connected to MUX0 (0x03)
* OUT1 of the TDA8540's is connected to "Monitor Out" (0x0C)
*
* TDA8540_ALT3 IN0-3 = Channel 13 - 16 (0x03)
* TDA8540_ALT4 IN0-3 = Channel 1 - 4 (0x03)
* TDA8540_ALT5 IN0-3 = Channel 5 - 8 (0x03)
* TDA8540_ALT6 IN0-3 = Channel 9 - 12 (0x03)
*
*/
/* All 7 possible sub-ids for the TDA8540 Matrix Switcher */
#define I2C_TDA8540 0x90
#define I2C_TDA8540_ALT1 0x92
#define I2C_TDA8540_ALT2 0x94
#define I2C_TDA8540_ALT3 0x96
#define I2C_TDA8540_ALT4 0x98
#define I2C_TDA8540_ALT5 0x9a
#define I2C_TDA8540_ALT6 0x9c
static void ivc120_muxsel(struct bttv *btv, unsigned int input)
{
// Simple maths
int key = input % 4;
int matrix = input / 4;
dprintk("bttv%d: ivc120_muxsel: Input - %02d | TDA - %02d | In - %02d\n",
btv->c.nr, input, matrix, key);
// Handles the input selection on the TDA8540's
bttv_I2CWrite(btv, I2C_TDA8540_ALT3, 0x00,
((matrix == 3) ? (key | key << 2) : 0x00), 1);
bttv_I2CWrite(btv, I2C_TDA8540_ALT4, 0x00,
((matrix == 0) ? (key | key << 2) : 0x00), 1);
bttv_I2CWrite(btv, I2C_TDA8540_ALT5, 0x00,
((matrix == 1) ? (key | key << 2) : 0x00), 1);
bttv_I2CWrite(btv, I2C_TDA8540_ALT6, 0x00,
((matrix == 2) ? (key | key << 2) : 0x00), 1);
// Handles the output enables on the TDA8540's
bttv_I2CWrite(btv, I2C_TDA8540_ALT3, 0x02,
((matrix == 3) ? 0x03 : 0x00), 1); // 13 - 16
bttv_I2CWrite(btv, I2C_TDA8540_ALT4, 0x02,
((matrix == 0) ? 0x03 : 0x00), 1); // 1-4
bttv_I2CWrite(btv, I2C_TDA8540_ALT5, 0x02,
((matrix == 1) ? 0x03 : 0x00), 1); // 5-8
bttv_I2CWrite(btv, I2C_TDA8540_ALT6, 0x02,
((matrix == 2) ? 0x03 : 0x00), 1); // 9-12
// Selects MUX0 for input on the 878
btaor((0)<<5, ~(3<<5), BT848_IFORM);
}
/* PXC200 muxsel helper
* luke@syseng.anu.edu.au
* another transplant
* from Alessandro Rubini (rubini@linux.it)
*
* There are 4 kinds of cards:
* PXC200L which is bt848
* PXC200F which is bt848 with PIC controlling mux
* PXC200AL which is bt878
* PXC200AF which is bt878 with PIC controlling mux
*/
#define PX_CFG_PXC200F 0x01
#define PX_FLAG_PXC200A 0x00001000 /* a pxc200A is bt-878 based */
#define PX_I2C_PIC 0x0f
#define PX_PXC200A_CARDID 0x200a1295
#define PX_I2C_CMD_CFG 0x00
static void PXC200_muxsel(struct bttv *btv, unsigned int input)
{
int rc;
long mux;
int bitmask;
unsigned char buf[2];
/* Read PIC config to determine if this is a PXC200F */
/* PX_I2C_CMD_CFG*/
buf[0]=0;
buf[1]=0;
rc=bttv_I2CWrite(btv,(PX_I2C_PIC<<1),buf[0],buf[1],1);
if (rc) {
printk(KERN_DEBUG "bttv%d: PXC200_muxsel: pic cfg write failed:%d\n", btv->c.nr,rc);
/* not PXC ? do nothing */
return;
}
rc=bttv_I2CRead(btv,(PX_I2C_PIC<<1),NULL);
if (!(rc & PX_CFG_PXC200F)) {
printk(KERN_DEBUG "bttv%d: PXC200_muxsel: not PXC200F rc:%d \n", btv->c.nr,rc);
return;
}
/* The multiplexer in the 200F is handled by the GPIO port */
/* get correct mapping between inputs */
/* mux = bttv_tvcards[btv->type].muxsel[input] & 3; */
/* ** not needed!? */
mux = input;
/* make sure output pins are enabled */
/* bitmask=0x30f; */
bitmask=0x302;
/* check whether we have a PXC200A */
if (btv->cardid == PX_PXC200A_CARDID) {
bitmask ^= 0x180; /* use 7 and 9, not 8 and 9 */
bitmask |= 7<<4; /* the DAC */
}
btwrite(bitmask, BT848_GPIO_OUT_EN);
bitmask = btread(BT848_GPIO_DATA);
if (btv->cardid == PX_PXC200A_CARDID)
bitmask = (bitmask & ~0x280) | ((mux & 2) << 8) | ((mux & 1) << 7);
else /* older device */
bitmask = (bitmask & ~0x300) | ((mux & 3) << 8);
btwrite(bitmask,BT848_GPIO_DATA);
/*
* Was "to be safe, set the bt848 to input 0"
* Actually, since it's ok at load time, better not messing
* with these bits (on PXC200AF you need to set mux 2 here)
*
* needed because bttv-driver sets mux before calling this function
*/
if (btv->cardid == PX_PXC200A_CARDID)
btaor(2<<5, ~BT848_IFORM_MUXSEL, BT848_IFORM);
else /* older device */
btand(~BT848_IFORM_MUXSEL,BT848_IFORM);
printk(KERN_DEBUG "bttv%d: setting input channel to:%d\n", btv->c.nr,(int)mux);
}
/* ----------------------------------------------------------------------- */
/* motherboard chipset specific stuff */
void __devinit bttv_check_chipset(void)
{
int pcipci_fail = 0;
struct pci_dev *dev = NULL;
if (pci_pci_problems & PCIPCI_FAIL)
pcipci_fail = 1;
if (pci_pci_problems & (PCIPCI_TRITON|PCIPCI_NATOMA|PCIPCI_VIAETBF))
triton1 = 1;
if (pci_pci_problems & PCIPCI_VSFX)
vsfx = 1;
#ifdef PCIPCI_ALIMAGIK
if (pci_pci_problems & PCIPCI_ALIMAGIK)
latency = 0x0A;
#endif
#if 0
/* print which chipset we have */
while ((dev = pci_find_class(PCI_CLASS_BRIDGE_HOST << 8,dev)))
printk(KERN_INFO "bttv: Host bridge is %s\n",pci_name(dev));
#endif
/* print warnings about any quirks found */
if (triton1)
printk(KERN_INFO "bttv: Host bridge needs ETBF enabled.\n");
if (vsfx)
printk(KERN_INFO "bttv: Host bridge needs VSFX enabled.\n");
if (pcipci_fail) {
printk(KERN_WARNING "bttv: BT848 and your chipset may not work together.\n");
if (UNSET == no_overlay) {
printk(KERN_WARNING "bttv: going to disable overlay.\n");
no_overlay = 1;
}
}
if (UNSET != latency)
printk(KERN_INFO "bttv: pci latency fixup [%d]\n",latency);
while ((dev = pci_find_device(PCI_VENDOR_ID_INTEL,
PCI_DEVICE_ID_INTEL_82441, dev))) {
unsigned char b;
pci_read_config_byte(dev, 0x53, &b);
if (bttv_debug)
printk(KERN_INFO "bttv: Host bridge: 82441FX Natoma, "
"bufcon=0x%02x\n",b);
}
}
int __devinit bttv_handle_chipset(struct bttv *btv)
{
unsigned char command;
if (!triton1 && !vsfx && UNSET == latency)
return 0;
if (bttv_verbose) {
if (triton1)
printk(KERN_INFO "bttv%d: enabling ETBF (430FX/VP3 compatibilty)\n",btv->c.nr);
if (vsfx && btv->id >= 878)
printk(KERN_INFO "bttv%d: enabling VSFX\n",btv->c.nr);
if (UNSET != latency)
printk(KERN_INFO "bttv%d: setting pci timer to %d\n",
btv->c.nr,latency);
}
if (btv->id < 878) {
/* bt848 (mis)uses a bit in the irq mask for etbf */
if (triton1)
btv->triton1 = BT848_INT_ETBF;
} else {
/* bt878 has a bit in the pci config space for it */
pci_read_config_byte(btv->c.pci, BT878_DEVCTRL, &command);
if (triton1)
command |= BT878_EN_TBFX;
if (vsfx)
command |= BT878_EN_VSFX;
pci_write_config_byte(btv->c.pci, BT878_DEVCTRL, command);
}
if (UNSET != latency)
pci_write_config_byte(btv->c.pci, PCI_LATENCY_TIMER, latency);
return 0;
}
/*
* Local variables:
* c-basic-offset: 8
* End:
*/
Reference in New Issue View Git Blame Copy Permalink