mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-28 22:54:05 +08:00
53e68c20ae
This driver implements monitoring and control of fans plugged into the device. Besides typical speed monitoring and PWM duty cycle control, voltage and current are reported for every fan. The device also has 2 connectors for RGB LEDs, support for them isn't implemented (mainly because there is no standardized sysfs interface). Also, the device has a noise sensor, but the sensor seems to be completely useless (and very imprecise), so support for it isn't implemented too. The driver coexists with userspace tools that access the device through hidraw interface with no known issues. The driver has been tested on x86_64, built in and as a module. Some changes/improvements were suggested by Jonas Malaco. Signed-off-by: Aleksandr Mezin <mezin.alexander@gmail.com> Link: https://lore.kernel.org/r/20211031033058.151014-1-mezin.alexander@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
63 lines
2.5 KiB
ReStructuredText
63 lines
2.5 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
Kernel driver nzxt-smart2
|
|
=========================
|
|
|
|
Supported devices:
|
|
|
|
- NZXT RGB & Fan controller
|
|
- NZXT Smart Device v2
|
|
|
|
Description
|
|
-----------
|
|
|
|
This driver implements monitoring and control of fans plugged into the device.
|
|
Besides typical speed monitoring and PWM duty cycle control, voltage and current
|
|
is reported for every fan.
|
|
|
|
The device also has two connectors for RGB LEDs; support for them isn't
|
|
implemented (mainly because there is no standardized sysfs interface).
|
|
|
|
Also, the device has a noise sensor, but the sensor seems to be completely
|
|
useless (and very imprecise), so support for it isn't implemented too.
|
|
|
|
Usage Notes
|
|
-----------
|
|
|
|
The device should be autodetected, and the driver should load automatically.
|
|
|
|
If fans are plugged in/unplugged while the system is powered on, the driver
|
|
must be reloaded to detect configuration changes; otherwise, new fans can't
|
|
be controlled (`pwm*` changes will be ignored). It is necessary because the
|
|
device has a dedicated "detect fans" command, and currently, it is executed only
|
|
during initialization. Speed, voltage, current monitoring will work even without
|
|
reload. As an alternative to reloading the module, a userspace tool (like
|
|
`liquidctl`_) can be used to run "detect fans" command through hidraw interface.
|
|
|
|
The driver coexists with userspace tools that access the device through hidraw
|
|
interface with no known issues.
|
|
|
|
.. _liquidctl: https://github.com/liquidctl/liquidctl
|
|
|
|
Sysfs entries
|
|
-------------
|
|
|
|
======================= ========================================================
|
|
fan[1-3]_input Fan speed monitoring (in rpm).
|
|
curr[1-3]_input Current supplied to the fan (in milliamperes).
|
|
in[0-2]_input Voltage supplied to the fan (in millivolts).
|
|
pwm[1-3] Controls fan speed: PWM duty cycle for PWM-controlled
|
|
fans, voltage for other fans. Voltage can be changed in
|
|
9-12 V range, but the value of the sysfs attribute is
|
|
always in 0-255 range (1 = 9V, 255 = 12V). Setting the
|
|
attribute to 0 turns off the fan completely.
|
|
pwm[1-3]_enable 1 if the fan can be controlled by writing to the
|
|
corresponding pwm* attribute, 0 otherwise. The device
|
|
can control only the fans it detected itself, so the
|
|
attribute is read-only.
|
|
pwm[1-3]_mode Read-only, 1 for PWM-controlled fans, 0 for other fans
|
|
(or if no fan connected).
|
|
update_interval The interval at which all inputs are updated (in
|
|
milliseconds). The default is 1000ms. Minimum is 250ms.
|
|
======================= ========================================================
|