mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-20 02:34:23 +08:00
59d3a193f1
Adds support for Cortina Systems Gemini family CPUs: http://www.cortina-systems.com/products/category/18 v3: - fixed __io(a) to be defined as __typesafe_io(a) v2: - #include <asm/io.h> -> <linux/io.h> - remove asm/system.h include - revorked mm.c to use named initializers - removed "empty" dma.h - updated copyrights Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
279 lines
8.5 KiB
C
279 lines
8.5 KiB
C
/*
|
|
* This file contains the hardware definitions for Gemini.
|
|
*
|
|
* Copyright (C) 2009 Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*/
|
|
#ifndef __MACH_GLOBAL_REG_H
|
|
#define __MACH_GLOBAL_REG_H
|
|
|
|
/* Global Word ID Register*/
|
|
#define GLOBAL_ID 0x00
|
|
|
|
#define CHIP_ID(reg) ((reg) >> 8)
|
|
#define CHIP_REVISION(reg) ((reg) & 0xFF)
|
|
|
|
/* Global Status Register */
|
|
#define GLOBAL_STATUS 0x04
|
|
|
|
#define CPU_BIG_ENDIAN (1 << 31)
|
|
#define PLL_OSC_30M (1 << 30) /* else 60MHz */
|
|
|
|
#define OPERATION_MODE_MASK (0xF << 26)
|
|
#define OPM_IDDQ (0xF << 26)
|
|
#define OPM_NAND (0xE << 26)
|
|
#define OPM_RING (0xD << 26)
|
|
#define OPM_DIRECT_BOOT (0xC << 26)
|
|
#define OPM_USB1_PHY_TEST (0xB << 26)
|
|
#define OPM_USB0_PHY_TEST (0xA << 26)
|
|
#define OPM_SATA1_PHY_TEST (0x9 << 26)
|
|
#define OPM_SATA0_PHY_TEST (0x8 << 26)
|
|
#define OPM_ICE_ARM (0x7 << 26)
|
|
#define OPM_ICE_FARADAY (0x6 << 26)
|
|
#define OPM_PLL_BYPASS (0x5 << 26)
|
|
#define OPM_DEBUG (0x4 << 26)
|
|
#define OPM_BURN_IN (0x3 << 26)
|
|
#define OPM_MBIST (0x2 << 26)
|
|
#define OPM_SCAN (0x1 << 26)
|
|
#define OPM_REAL (0x0 << 26)
|
|
|
|
#define FLASH_TYPE_MASK (0x3 << 24)
|
|
#define FLASH_TYPE_NAND_2K (0x3 << 24)
|
|
#define FLASH_TYPE_NAND_512 (0x2 << 24)
|
|
#define FLASH_TYPE_PARALLEL (0x1 << 24)
|
|
#define FLASH_TYPE_SERIAL (0x0 << 24)
|
|
/* if parallel */
|
|
#define FLASH_WIDTH_16BIT (1 << 23) /* else 8 bit */
|
|
/* if serial */
|
|
#define FLASH_ATMEL (1 << 23) /* else STM */
|
|
|
|
#define FLASH_SIZE_MASK (0x3 << 21)
|
|
#define NAND_256M (0x3 << 21) /* and more */
|
|
#define NAND_128M (0x2 << 21)
|
|
#define NAND_64M (0x1 << 21)
|
|
#define NAND_32M (0x0 << 21)
|
|
#define ATMEL_16M (0x3 << 21) /* and more */
|
|
#define ATMEL_8M (0x2 << 21)
|
|
#define ATMEL_4M_2M (0x1 << 21)
|
|
#define ATMEL_1M (0x0 << 21) /* and less */
|
|
#define STM_32M (1 << 22) /* and more */
|
|
#define STM_16M (0 << 22) /* and less */
|
|
|
|
#define FLASH_PARALLEL_HIGH_PIN_CNT (1 << 20) /* else low pin cnt */
|
|
|
|
#define CPU_AHB_RATIO_MASK (0x3 << 18)
|
|
#define CPU_AHB_1_1 (0x0 << 18)
|
|
#define CPU_AHB_3_2 (0x1 << 18)
|
|
#define CPU_AHB_24_13 (0x2 << 18)
|
|
#define CPU_AHB_2_1 (0x3 << 18)
|
|
|
|
#define REG_TO_AHB_SPEED(reg) ((((reg) >> 15) & 0x7) * 10 + 130)
|
|
#define AHB_SPEED_TO_REG(x) ((((x - 130)) / 10) << 15)
|
|
|
|
/* it is posible to override some settings, use >> OVERRIDE_xxxx_SHIFT */
|
|
#define OVERRIDE_FLASH_TYPE_SHIFT 16
|
|
#define OVERRIDE_FLASH_WIDTH_SHIFT 16
|
|
#define OVERRIDE_FLASH_SIZE_SHIFT 16
|
|
#define OVERRIDE_CPU_AHB_RATIO_SHIFT 15
|
|
#define OVERRIDE_AHB_SPEED_SHIFT 15
|
|
|
|
/* Global PLL Control Register */
|
|
#define GLOBAL_PLL_CTRL 0x08
|
|
|
|
#define PLL_BYPASS (1 << 31)
|
|
#define PLL_POWER_DOWN (1 << 8)
|
|
#define PLL_CONTROL_Q (0x1F << 0)
|
|
|
|
/* Global Soft Reset Control Register */
|
|
#define GLOBAL_RESET 0x0C
|
|
|
|
#define RESET_GLOBAL (1 << 31)
|
|
#define RESET_CPU1 (1 << 30)
|
|
#define RESET_TVE (1 << 28)
|
|
#define RESET_SATA1 (1 << 27)
|
|
#define RESET_SATA0 (1 << 26)
|
|
#define RESET_CIR (1 << 25)
|
|
#define RESET_EXT_DEV (1 << 24)
|
|
#define RESET_WD (1 << 23)
|
|
#define RESET_GPIO2 (1 << 22)
|
|
#define RESET_GPIO1 (1 << 21)
|
|
#define RESET_GPIO0 (1 << 20)
|
|
#define RESET_SSP (1 << 19)
|
|
#define RESET_UART (1 << 18)
|
|
#define RESET_TIMER (1 << 17)
|
|
#define RESET_RTC (1 << 16)
|
|
#define RESET_INT1 (1 << 15)
|
|
#define RESET_INT0 (1 << 14)
|
|
#define RESET_LCD (1 << 13)
|
|
#define RESET_LPC (1 << 12)
|
|
#define RESET_APB (1 << 11)
|
|
#define RESET_DMA (1 << 10)
|
|
#define RESET_USB1 (1 << 9)
|
|
#define RESET_USB0 (1 << 8)
|
|
#define RESET_PCI (1 << 7)
|
|
#define RESET_GMAC1 (1 << 6)
|
|
#define RESET_GMAC0 (1 << 5)
|
|
#define RESET_SECURITY (1 << 4)
|
|
#define RESET_RAID (1 << 3)
|
|
#define RESET_IDE (1 << 2)
|
|
#define RESET_FLASH (1 << 1)
|
|
#define RESET_DRAM (1 << 0)
|
|
|
|
/* Global IO Pad Driving Capability Control Register */
|
|
#define GLOBAL_IO_DRIVING_CTRL 0x10
|
|
|
|
#define DRIVING_CURRENT_MASK 0x3
|
|
|
|
/* here 00-4mA, 01-8mA, 10-12mA, 11-16mA */
|
|
#define GPIO1_PADS_31_28_SHIFT 28
|
|
#define GPIO0_PADS_31_16_SHIFT 26
|
|
#define GPIO0_PADS_15_0_SHIFT 24
|
|
#define PCI_AND_EXT_RESET_PADS_SHIFT 22
|
|
#define IDE_PADS_SHIFT 20
|
|
#define GMAC1_PADS_SHIFT 18
|
|
#define GMAC0_PADS_SHIFT 16
|
|
/* DRAM is not in mA and poorly documented */
|
|
#define DRAM_CLOCK_PADS_SHIFT 8
|
|
#define DRAM_DATA_PADS_SHIFT 4
|
|
#define DRAM_CONTROL_PADS_SHIFT 0
|
|
|
|
/* Global IO Pad Slew Rate Control Register */
|
|
#define GLOBAL_IO_SLEW_RATE_CTRL 0x14
|
|
|
|
#define GPIO1_PADS_31_28_SLOW (1 << 10)
|
|
#define GPIO0_PADS_31_16_SLOW (1 << 9)
|
|
#define GPIO0_PADS_15_0_SLOW (1 << 8)
|
|
#define PCI_PADS_SLOW (1 << 7)
|
|
#define IDE_PADS_SLOW (1 << 6)
|
|
#define GMAC1_PADS_SLOW (1 << 5)
|
|
#define GMAC0_PADS_SLOW (1 << 4)
|
|
#define DRAM_CLOCK_PADS_SLOW (1 << 1)
|
|
#define DRAM_IO_PADS_SLOW (1 << 0)
|
|
|
|
/*
|
|
* General skew control defines
|
|
* 16 steps, each step is around 0.2ns
|
|
*/
|
|
#define SKEW_MASK 0xF
|
|
|
|
/* Global IDE PAD Skew Control Register */
|
|
#define GLOBAL_IDE_SKEW_CTRL 0x18
|
|
|
|
#define IDE1_HOST_STROBE_DELAY_SHIFT 28
|
|
#define IDE1_DEVICE_STROBE_DELAY_SHIFT 24
|
|
#define IDE1_OUTPUT_IO_SKEW_SHIFT 20
|
|
#define IDE1_INPUT_IO_SKEW_SHIFT 16
|
|
#define IDE0_HOST_STROBE_DELAY_SHIFT 12
|
|
#define IDE0_DEVICE_STROBE_DELAY_SHIFT 8
|
|
#define IDE0_OUTPUT_IO_SKEW_SHIFT 4
|
|
#define IDE0_INPUT_IO_SKEW_SHIFT 0
|
|
|
|
/* Global GMAC Control Pad Skew Control Register */
|
|
#define GLOBAL_GMAC_CTRL_SKEW_CTRL 0x1C
|
|
|
|
#define GMAC1_TXC_SKEW_SHIFT 28
|
|
#define GMAC1_TXEN_SKEW_SHIFT 24
|
|
#define GMAC1_RXC_SKEW_SHIFT 20
|
|
#define GMAC1_RXDV_SKEW_SHIFT 16
|
|
#define GMAC0_TXC_SKEW_SHIFT 12
|
|
#define GMAC0_TXEN_SKEW_SHIFT 8
|
|
#define GMAC0_RXC_SKEW_SHIFT 4
|
|
#define GMAC0_RXDV_SKEW_SHIFT 0
|
|
|
|
/* Global GMAC0 Data PAD Skew Control Register */
|
|
#define GLOBAL_GMAC0_DATA_SKEW_CTRL 0x20
|
|
/* Global GMAC1 Data PAD Skew Control Register */
|
|
#define GLOBAL_GMAC1_DATA_SKEW_CTRL 0x24
|
|
|
|
#define GMAC_TXD_SKEW_SHIFT(x) (((x) * 4) + 16)
|
|
#define GMAC_RXD_SKEW_SHIFT(x) ((x) * 4)
|
|
|
|
/* CPU has two AHB busses. */
|
|
|
|
/* Global Arbitration0 Control Register */
|
|
#define GLOBAL_ARBITRATION0_CTRL 0x28
|
|
|
|
#define BOOT_CONTROLLER_HIGH_PRIO (1 << 3)
|
|
#define DMA_BUS1_HIGH_PRIO (1 << 2)
|
|
#define CPU0_HIGH_PRIO (1 << 0)
|
|
|
|
/* Global Arbitration1 Control Register */
|
|
#define GLOBAL_ARBITRATION1_CTRL 0x2C
|
|
|
|
#define TVE_HIGH_PRIO (1 << 9)
|
|
#define PCI_HIGH_PRIO (1 << 8)
|
|
#define USB1_HIGH_PRIO (1 << 7)
|
|
#define USB0_HIGH_PRIO (1 << 6)
|
|
#define GMAC1_HIGH_PRIO (1 << 5)
|
|
#define GMAC0_HIGH_PRIO (1 << 4)
|
|
#define SECURITY_HIGH_PRIO (1 << 3)
|
|
#define RAID_HIGH_PRIO (1 << 2)
|
|
#define IDE_HIGH_PRIO (1 << 1)
|
|
#define DMA_BUS2_HIGH_PRIO (1 << 0)
|
|
|
|
/* Common bits for both arbitration registers */
|
|
#define BURST_LENGTH_SHIFT 16
|
|
#define BURST_LENGTH_MASK (0x3F << 16)
|
|
|
|
/* Miscellaneous Control Register */
|
|
#define GLOBAL_MISC_CTRL 0x30
|
|
|
|
#define MEMORY_SPACE_SWAP (1 << 31)
|
|
#define USB1_PLUG_MINIB (1 << 30) /* else plug is mini-A */
|
|
#define USB0_PLUG_MINIB (1 << 29)
|
|
#define GMAC_GMII (1 << 28)
|
|
#define GMAC_1_ENABLE (1 << 27)
|
|
/* TODO: define ATA/SATA bits */
|
|
#define USB1_VBUS_ON (1 << 23)
|
|
#define USB0_VBUS_ON (1 << 22)
|
|
#define APB_CLKOUT_ENABLE (1 << 21)
|
|
#define TVC_CLKOUT_ENABLE (1 << 20)
|
|
#define EXT_CLKIN_ENABLE (1 << 19)
|
|
#define PCI_66MHZ (1 << 18) /* else 33 MHz */
|
|
#define PCI_CLKOUT_ENABLE (1 << 17)
|
|
#define LPC_CLKOUT_ENABLE (1 << 16)
|
|
#define USB1_WAKEUP_ON (1 << 15)
|
|
#define USB0_WAKEUP_ON (1 << 14)
|
|
/* TODO: define PCI idle detect bits */
|
|
#define TVC_PADS_ENABLE (1 << 9)
|
|
#define SSP_PADS_ENABLE (1 << 8)
|
|
#define LCD_PADS_ENABLE (1 << 7)
|
|
#define LPC_PADS_ENABLE (1 << 6)
|
|
#define PCI_PADS_ENABLE (1 << 5)
|
|
#define IDE_PADS_ENABLE (1 << 4)
|
|
#define DRAM_PADS_POWER_DOWN (1 << 3)
|
|
#define NAND_PADS_DISABLE (1 << 2)
|
|
#define PFLASH_PADS_DISABLE (1 << 1)
|
|
#define SFLASH_PADS_DISABLE (1 << 0)
|
|
|
|
/* Global Clock Control Register */
|
|
#define GLOBAL_CLOCK_CTRL 0x34
|
|
|
|
#define POWER_STATE_G0 (1 << 31)
|
|
#define POWER_STATE_S1 (1 << 30) /* else it is S3/S4 state */
|
|
#define SECURITY_APB_AHB (1 << 29)
|
|
/* else Security APB clk will be 0.75xAHB */
|
|
/* TODO: TVC clock divider */
|
|
#define PCI_CLKRUN_ENABLE (1 << 16)
|
|
#define BOOT_CLK_DISABLE (1 << 13)
|
|
#define TVC_CLK_DISABLE (1 << 12)
|
|
#define FLASH_CLK_DISABLE (1 << 11)
|
|
#define DDR_CLK_DISABLE (1 << 10)
|
|
#define PCI_CLK_DISABLE (1 << 9)
|
|
#define IDE_CLK_DISABLE (1 << 8)
|
|
#define USB1_CLK_DISABLE (1 << 7)
|
|
#define USB0_CLK_DISABLE (1 << 6)
|
|
#define SATA1_CLK_DISABLE (1 << 5)
|
|
#define SATA0_CLK_DISABLE (1 << 4)
|
|
#define GMAC1_CLK_DISABLE (1 << 3)
|
|
#define GMAC0_CLK_DISABLE (1 << 2)
|
|
#define SECURITY_CLK_DISABLE (1 << 1)
|
|
|
|
/* TODO: other registers definitions if needed */
|
|
|
|
#endif /* __MACH_GLOBAL_REG_H */
|