mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-19 17:14:40 +08:00
01f714ee02
Commitdfeef15e73("counter: microchip-tcp-capture: Add appropriate arch deps for TCP driver") intends to add appropriate dependencies for the config MICROCHIP_TCB_CAPTURE. It however prefixes the intended configs with CONFIG, but in Kconfig files in contrast to source files, the configs are referenced to without prefixing them with CONFIG. Fix the dependency references due to this minor misconception. Fixes:dfeef15e73("counter: microchip-tcp-capture: Add appropriate arch deps for TCP driver") Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com> Link: https://lore.kernel.org/r/20230118074659.5909-1-lukas.bulwahn@gmail.com/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
123 lines
3.8 KiB
Plaintext
123 lines
3.8 KiB
Plaintext
# SPDX-License-Identifier: GPL-2.0-only
|
|
#
|
|
# Counter devices
|
|
#
|
|
|
|
menuconfig COUNTER
|
|
tristate "Counter support"
|
|
help
|
|
This enables counter device support through the Generic Counter
|
|
interface. You only need to enable this, if you also want to enable
|
|
one or more of the counter device drivers below.
|
|
|
|
if COUNTER
|
|
|
|
config 104_QUAD_8
|
|
tristate "ACCES 104-QUAD-8 driver"
|
|
depends on (PC104 && X86) || COMPILE_TEST
|
|
select ISA_BUS_API
|
|
help
|
|
Say yes here to build support for the ACCES 104-QUAD-8 quadrature
|
|
encoder counter/interface device family (104-QUAD-8, 104-QUAD-4).
|
|
|
|
A counter's respective error flag may be cleared by performing a write
|
|
operation on the respective count value attribute. Although the
|
|
104-QUAD-8 counters have a 25-bit range, only the lower 24 bits may be
|
|
set, either directly or via the counter's preset attribute.
|
|
|
|
The base port addresses for the devices may be configured via the base
|
|
array module parameter. The interrupt line numbers for the devices may
|
|
be configured via the irq array module parameter.
|
|
|
|
config FTM_QUADDEC
|
|
tristate "Flex Timer Module Quadrature decoder driver"
|
|
depends on SOC_LS1021A || COMPILE_TEST
|
|
depends on HAS_IOMEM && OF
|
|
help
|
|
Select this option to enable the Flex Timer Quadrature decoder
|
|
driver.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called ftm-quaddec.
|
|
|
|
config INTEL_QEP
|
|
tristate "Intel Quadrature Encoder Peripheral driver"
|
|
depends on X86
|
|
depends on PCI
|
|
help
|
|
Select this option to enable the Intel Quadrature Encoder Peripheral
|
|
driver.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called intel-qep.
|
|
|
|
config INTERRUPT_CNT
|
|
tristate "Interrupt counter driver"
|
|
depends on GPIOLIB
|
|
help
|
|
Select this option to enable interrupt counter driver. Any interrupt
|
|
source can be used by this driver as the event source.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called interrupt-cnt.
|
|
|
|
config MICROCHIP_TCB_CAPTURE
|
|
tristate "Microchip Timer Counter Capture driver"
|
|
depends on SOC_AT91SAM9 || SOC_SAM_V7 || COMPILE_TEST
|
|
depends on HAS_IOMEM && OF
|
|
select REGMAP_MMIO
|
|
help
|
|
Select this option to enable the Microchip Timer Counter Block
|
|
capture driver.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called microchip-tcb-capture.
|
|
|
|
config STM32_LPTIMER_CNT
|
|
tristate "STM32 LP Timer encoder counter driver"
|
|
depends on MFD_STM32_LPTIMER || COMPILE_TEST
|
|
help
|
|
Select this option to enable STM32 Low-Power Timer quadrature encoder
|
|
and counter driver.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called stm32-lptimer-cnt.
|
|
|
|
config STM32_TIMER_CNT
|
|
tristate "STM32 Timer encoder counter driver"
|
|
depends on MFD_STM32_TIMERS || COMPILE_TEST
|
|
help
|
|
Select this option to enable STM32 Timer quadrature encoder
|
|
and counter driver.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called stm32-timer-cnt.
|
|
|
|
config TI_ECAP_CAPTURE
|
|
tristate "TI eCAP capture driver"
|
|
depends on ARCH_OMAP2PLUS || ARCH_DAVINCI_DA8XX || ARCH_KEYSTONE || ARCH_K3 || COMPILE_TEST
|
|
depends on HAS_IOMEM
|
|
select REGMAP_MMIO
|
|
help
|
|
Select this option to enable the Texas Instruments Enhanced Capture
|
|
(eCAP) driver in input mode.
|
|
|
|
It can be used to timestamp events (falling/rising edges) detected
|
|
on ECAP input signal.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called ti-ecap-capture.
|
|
|
|
config TI_EQEP
|
|
tristate "TI eQEP counter driver"
|
|
depends on (SOC_AM33XX || COMPILE_TEST)
|
|
select REGMAP_MMIO
|
|
help
|
|
Select this option to enable the Texas Instruments Enhanced Quadrature
|
|
Encoder Pulse (eQEP) counter driver.
|
|
|
|
To compile this driver as a module, choose M here: the module will be
|
|
called ti-eqep.
|
|
|
|
endif # COUNTER
|