korg/linux
0
0
Fork 0
mirror of https://mirrors.bfsu.edu.cn/git/linux.git synced 2024-11-17 01:04:19 +08:00
Code Issues Packages Projects Releases Wiki Activity
8e320d0271
linux/drivers/net/tokenring/tms380tr.h
Stephen Hemminger f1608f859a tms380tr: convert to net_device_ops 
Conver this related group of drivers to new API

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-21 14:02:30 -08:00

1142 lines
39 KiB
C
Raw Blame History

/*
* tms380tr.h: TI TMS380 Token Ring driver for Linux
*
* Authors:
* - Christoph Goos <cgoos@syskonnect.de>
* - Adam Fritzler
*/
#ifndef __LINUX_TMS380TR_H
#define __LINUX_TMS380TR_H
#ifdef __KERNEL__
#include <linux/interrupt.h>
/* module prototypes */
extern const struct net_device_ops tms380tr_netdev_ops;
int tms380tr_open(struct net_device *dev);
int tms380tr_close(struct net_device *dev);
irqreturn_t tms380tr_interrupt(int irq, void *dev_id);
int tmsdev_init(struct net_device *dev, struct device *pdev);
void tmsdev_term(struct net_device *dev);
void tms380tr_wait(unsigned long time);
#define TMS380TR_MAX_ADAPTERS 7
#define SEND_TIMEOUT 10*HZ
#define TR_RCF_LONGEST_FRAME_MASK 0x0070
#define TR_RCF_FRAME4K 0x0030
/*------------------------------------------------------------------*/
/* Bit order for adapter communication with DMA */
/* -------------------------------------------------------------- */
/* Bit 8 | 9| 10| 11|| 12| 13| 14| 15|| 0| 1| 2| 3|| 4| 5| 6| 7| */
/* -------------------------------------------------------------- */
/* The bytes in a word must be byte swapped. Also, if a double */
/* word is used for storage, then the words, as well as the bytes, */
/* must be swapped. */
/* Bit order for adapter communication with DIO */
/* -------------------------------------------------------------- */
/* Bit 0 | 1| 2| 3|| 4| 5| 6| 7|| 8| 9| 10| 11|| 12| 13| 14| 15| */
/* -------------------------------------------------------------- */
/*------------------------------------------------------------------*/
/* Swap words of a long. */
#define SWAPW(x) (((x) << 16) | ((x) >> 16))
/* Get the low byte of a word. */
#define LOBYTE(w) ((unsigned char)(w))
/* Get the high byte of a word. */
#define HIBYTE(w) ((unsigned char)((unsigned short)(w) >> 8))
/* Get the low word of a long. */
#define LOWORD(l) ((unsigned short)(l))
/* Get the high word of a long. */
#define HIWORD(l) ((unsigned short)((unsigned long)(l) >> 16))
/* Token ring adapter I/O addresses for normal mode. */
/*
* The SIF registers. Common to all adapters.
*/
/* Basic SIF (SRSX = 0) */
#define SIFDAT 0x00 /* SIF/DMA data. */
#define SIFINC 0x02 /* IO Word data with auto increment. */
#define SIFINH 0x03 /* IO Byte data with auto increment. */
#define SIFADR 0x04 /* SIF/DMA Address. */
#define SIFCMD 0x06 /* SIF Command. */
#define SIFSTS 0x06 /* SIF Status. */
/* "Extended" SIF (SRSX = 1) */
#define SIFACL 0x08 /* SIF Adapter Control Register. */
#define SIFADD 0x0a /* SIF/DMA Address. -- 0x0a */
#define SIFADX 0x0c /* 0x0c */
#define DMALEN 0x0e /* SIF DMA length. -- 0x0e */
/*
* POS Registers. Only for ISA Adapters.
*/
#define POSREG 0x10 /* Adapter Program Option Select (POS)
* Register: base IO address + 16 byte.
*/
#define POSREG_2 24L /* only for TR4/16+ adapter
* base IO address + 24 byte. -- 0x18
*/
/* SIFCMD command codes (high-low) */
#define CMD_INTERRUPT_ADAPTER 0x8000 /* Cause internal adapter interrupt */
#define CMD_ADAPTER_RESET 0x4000 /* Hardware reset of adapter */
#define CMD_SSB_CLEAR 0x2000 /* Acknowledge to adapter to
* system interrupts.
*/
#define CMD_EXECUTE 0x1000 /* Execute SCB command */
#define CMD_SCB_REQUEST 0x0800 /* Request adapter to interrupt
* system when SCB is available for
* another command.
*/
#define CMD_RX_CONTINUE 0x0400 /* Continue receive after odd pointer
* stop. (odd pointer receive method)
*/
#define CMD_RX_VALID 0x0200 /* Now actual RPL is valid. */
#define CMD_TX_VALID 0x0100 /* Now actual TPL is valid. (valid
* bit receive/transmit method)
*/
#define CMD_SYSTEM_IRQ 0x0080 /* Adapter-to-attached-system
* interrupt is reset.
*/
#define CMD_CLEAR_SYSTEM_IRQ 0x0080 /* Clear SYSTEM_INTERRUPT bit.
* (write: 1=ignore, 0=reset)
*/
#define EXEC_SOFT_RESET 0xFF00 /* adapter soft reset. (restart
* adapter after hardware reset)
*/
/* ACL commands (high-low) */
#define ACL_SWHLDA 0x0800 /* Software hold acknowledge. */
#define ACL_SWDDIR 0x0400 /* Data transfer direction. */
#define ACL_SWHRQ 0x0200 /* Pseudo DMA operation. */
#define ACL_PSDMAEN 0x0100 /* Enable pseudo system DMA. */
#define ACL_ARESET 0x0080 /* Adapter hardware reset command.
* (held in reset condition as
* long as bit is set)
*/
#define ACL_CPHALT 0x0040 /* Communication processor halt.
* (can only be set while ACL_ARESET
* bit is set; prevents adapter
* processor from executing code while
* downloading firmware)
*/
#define ACL_BOOT 0x0020
#define ACL_SINTEN 0x0008 /* System interrupt enable/disable
* (1/0): can be written if ACL_ARESET
* is zero.
*/
#define ACL_PEN 0x0004
#define ACL_NSELOUT0 0x0002
#define ACL_NSELOUT1 0x0001 /* NSELOUTx have a card-specific
* meaning for setting ring speed.
*/
#define PS_DMA_MASK (ACL_SWHRQ | ACL_PSDMAEN)
/* SIFSTS register return codes (high-low) */
#define STS_SYSTEM_IRQ 0x0080 /* Adapter-to-attached-system
* interrupt is valid.
*/
#define STS_INITIALIZE 0x0040 /* INITIALIZE status. (ready to
* initialize)
*/
#define STS_TEST 0x0020 /* TEST status. (BUD not completed) */
#define STS_ERROR 0x0010 /* ERROR status. (unrecoverable
* HW error occurred)
*/
#define STS_MASK 0x00F0 /* Mask interesting status bits. */
#define STS_ERROR_MASK 0x000F /* Get Error Code by masking the
* interrupt code bits.
*/
#define ADAPTER_INT_PTRS 0x0A00 /* Address offset of adapter internal
* pointers 01:0a00 (high-low) have to
* be read after init and before open.
*/
/* Interrupt Codes (only MAC IRQs) */
#define STS_IRQ_ADAPTER_CHECK 0x0000 /* unrecoverable hardware or
* software error.
*/
#define STS_IRQ_RING_STATUS 0x0004 /* SSB is updated with ring status. */
#define STS_IRQ_LLC_STATUS 0x0005 /* Not used in MAC-only microcode */
#define STS_IRQ_SCB_CLEAR 0x0006 /* SCB clear, following an
* SCB_REQUEST IRQ.
*/
#define STS_IRQ_TIMER 0x0007 /* Not normally used in MAC ucode */
#define STS_IRQ_COMMAND_STATUS 0x0008 /* SSB is updated with command
* status.
*/
#define STS_IRQ_RECEIVE_STATUS 0x000A /* SSB is updated with receive
* status.
*/
#define STS_IRQ_TRANSMIT_STATUS 0x000C /* SSB is updated with transmit
* status
*/
#define STS_IRQ_RECEIVE_PENDING 0x000E /* Not used in MAC-only microcode */
#define STS_IRQ_MASK 0x000F /* = STS_ERROR_MASK. */
/* TRANSMIT_STATUS completion code: (SSB.Parm[0]) */
#define COMMAND_COMPLETE 0x0080 /* TRANSMIT command completed
* (avoid this!) issue another transmit
* to send additional frames.
*/
#define FRAME_COMPLETE 0x0040 /* Frame has been transmitted;
* INTERRUPT_FRAME bit was set in the
* CSTAT request; indication of possibly
* more than one frame transmissions!
* SSB.Parm[0-1]: 32 bit pointer to
* TPL of last frame.
*/
#define LIST_ERROR 0x0020 /* Error in one of the TPLs that
* compose the frame; TRANSMIT
* terminated; Parm[1-2]: 32bit pointer
* to TPL which starts the error
* frame; error details in bits 8-13.
* (14?)
*/
#define FRAME_SIZE_ERROR 0x8000 /* FRAME_SIZE does not equal the sum of
* the valid DATA_COUNT fields;
* FRAME_SIZE less than header plus
* information field. (15 bytes +
* routing field) Or if FRAME_SIZE
* was specified as zero in one list.
*/
#define TX_THRESHOLD 0x4000 /* FRAME_SIZE greater than (BUFFER_SIZE
* - 9) * TX_BUF_MAX.
*/
#define ODD_ADDRESS 0x2000 /* Odd forward pointer value is
* read on a list without END_FRAME
* indication.
*/
#define FRAME_ERROR 0x1000 /* START_FRAME bit (not) anticipated,
* but (not) set.
*/
#define ACCESS_PRIORITY_ERROR 0x0800 /* Access priority requested has not
* been allowed.
*/
#define UNENABLED_MAC_FRAME 0x0400 /* MAC frame has source class of zero
* or MAC frame PCF ATTN field is
* greater than one.
*/
#define ILLEGAL_FRAME_FORMAT 0x0200 /* Bit 0 or FC field was set to one. */
/*
* Since we need to support some functions even if the adapter is in a
* CLOSED state, we have a (pseudo-) command queue which holds commands
* that are outstandig to be executed.
*
* Each time a command completes, an interrupt occurs and the next
* command is executed. The command queue is actually a simple word with
* a bit for each outstandig command. Therefore the commands will not be
* executed in the order they have been queued.
*
* The following defines the command code bits and the command queue:
*/
#define OC_OPEN 0x0001 /* OPEN command */
#define OC_TRANSMIT 0x0002 /* TRANSMIT command */
#define OC_TRANSMIT_HALT 0x0004 /* TRANSMIT_HALT command */
#define OC_RECEIVE 0x0008 /* RECEIVE command */
#define OC_CLOSE 0x0010 /* CLOSE command */
#define OC_SET_GROUP_ADDR 0x0020 /* SET_GROUP_ADDR command */
#define OC_SET_FUNCT_ADDR 0x0040 /* SET_FUNCT_ADDR command */
#define OC_READ_ERROR_LOG 0x0080 /* READ_ERROR_LOG command */
#define OC_READ_ADAPTER 0x0100 /* READ_ADAPTER command */
#define OC_MODIFY_OPEN_PARMS 0x0400 /* MODIFY_OPEN_PARMS command */
#define OC_RESTORE_OPEN_PARMS 0x0800 /* RESTORE_OPEN_PARMS command */
#define OC_SET_FIRST_16_GROUP 0x1000 /* SET_FIRST_16_GROUP command */
#define OC_SET_BRIDGE_PARMS 0x2000 /* SET_BRIDGE_PARMS command */
#define OC_CONFIG_BRIDGE_PARMS 0x4000 /* CONFIG_BRIDGE_PARMS command */
#define OPEN 0x0300 /* C: open command. S: completion. */
#define TRANSMIT 0x0400 /* C: transmit command. S: completion
* status. (reject: COMMAND_REJECT if
* adapter not opened, TRANSMIT already
* issued or address passed in the SCB
* not word aligned)
*/
#define TRANSMIT_HALT 0x0500 /* C: interrupt TX TPL chain; if no
* TRANSMIT command issued, the command
* is ignored (completion with TRANSMIT
* status (0x0400)!)
*/
#define RECEIVE 0x0600 /* C: receive command. S: completion
* status. (reject: COMMAND_REJECT if
* adapter not opened, RECEIVE already
* issued or address passed in the SCB
* not word aligned)
*/
#define CLOSE 0x0700 /* C: close adapter. S: completion.
* (COMMAND_REJECT if adapter not open)
*/
#define SET_GROUP_ADDR 0x0800 /* C: alter adapter group address after
* OPEN. S: completion. (COMMAND_REJECT
* if adapter not open)
*/
#define SET_FUNCT_ADDR 0x0900 /* C: alter adapter functional address
* after OPEN. S: completion.
* (COMMAND_REJECT if adapter not open)
*/
#define READ_ERROR_LOG 0x0A00 /* C: read adapter error counters.
* S: completion. (command ignored
* if adapter not open!)
*/
#define READ_ADAPTER 0x0B00 /* C: read data from adapter memory.
* (important: after init and before
* open!) S: completion. (ADAPTER_CHECK
* interrupt if undefined storage area
* read)
*/
#define MODIFY_OPEN_PARMS 0x0D00 /* C: modify some adapter operational
* parameters. (bit correspondend to
* WRAP_INTERFACE is ignored)
* S: completion. (reject:
* COMMAND_REJECT)
*/
#define RESTORE_OPEN_PARMS 0x0E00 /* C: modify some adapter operational
* parameters. (bit correspondend
* to WRAP_INTERFACE is ignored)
* S: completion. (reject:
* COMMAND_REJECT)
*/
#define SET_FIRST_16_GROUP 0x0F00 /* C: alter the first two bytes in
* adapter group address.
* S: completion. (reject:
* COMMAND_REJECT)
*/
#define SET_BRIDGE_PARMS 0x1000 /* C: values and conditions for the
* adapter hardware to use when frames
* are copied for forwarding.
* S: completion. (reject:
* COMMAND_REJECT)
*/
#define CONFIG_BRIDGE_PARMS 0x1100 /* C: ..
* S: completion. (reject:
* COMMAND_REJECT)
*/
#define SPEED_4 4
#define SPEED_16 16 /* Default transmission speed */
/* Initialization Parameter Block (IPB); word alignment necessary! */
#define BURST_SIZE 0x0018 /* Default burst size */
#define BURST_MODE 0x9F00 /* Burst mode enable */
#define DMA_RETRIES 0x0505 /* Magic DMA retry number... */
#define CYCLE_TIME 3 /* Default AT-bus cycle time: 500 ns
* (later adapter version: fix cycle time!)
*/
#define LINE_SPEED_BIT 0x80
/* Macro definition for the wait function. */
#define ONE_SECOND_TICKS 1000000
#define HALF_SECOND (ONE_SECOND_TICKS / 2)
#define ONE_SECOND (ONE_SECOND_TICKS)
#define TWO_SECONDS (ONE_SECOND_TICKS * 2)
#define THREE_SECONDS (ONE_SECOND_TICKS * 3)
#define FOUR_SECONDS (ONE_SECOND_TICKS * 4)
#define FIVE_SECONDS (ONE_SECOND_TICKS * 5)
#define BUFFER_SIZE 2048 /* Buffers on Adapter */
#pragma pack(1)
typedef struct {
unsigned short Init_Options; /* Initialize with burst mode;
* LLC disabled. (MAC only)
*/
/* Interrupt vectors the adapter places on attached system bus. */
u_int8_t CMD_Status_IV; /* Interrupt vector: command status. */
u_int8_t TX_IV; /* Interrupt vector: transmit. */
u_int8_t RX_IV; /* Interrupt vector: receive. */
u_int8_t Ring_Status_IV; /* Interrupt vector: ring status. */
u_int8_t SCB_Clear_IV; /* Interrupt vector: SCB clear. */
u_int8_t Adapter_CHK_IV; /* Interrupt vector: adapter check. */
u_int16_t RX_Burst_Size; /* Max. number of transfer cycles. */
u_int16_t TX_Burst_Size; /* During DMA burst; even value! */
u_int16_t DMA_Abort_Thrhld; /* Number of DMA retries. */
u_int32_t SCB_Addr; /* SCB address: even, word aligned, high-low */
u_int32_t SSB_Addr; /* SSB address: even, word aligned, high-low */
} IPB, *IPB_Ptr;
#pragma pack()
/*
* OPEN Command Parameter List (OCPL) (can be reused, if the adapter has to
* be reopened)
*/
#define BUFFER_SIZE 2048 /* Buffers on Adapter. */
#define TPL_SIZE 8+6*TX_FRAG_NUM /* Depending on fragments per TPL. */
#define RPL_SIZE 14 /* (with TI firmware v2.26 handling
* up to nine fragments possible)
*/
#define TX_BUF_MIN 20 /* ??? (Stephan: calculation with */
#define TX_BUF_MAX 40 /* BUFFER_SIZE and MAX_FRAME_SIZE) ???
*/
#define DISABLE_EARLY_TOKEN_RELEASE 0x1000
/* OPEN Options (high-low) */
#define WRAP_INTERFACE 0x0080 /* Inserting omitted for test
* purposes; transmit data appears
* as receive data. (useful for
* testing; change: CLOSE necessary)
*/
#define DISABLE_HARD_ERROR 0x0040 /* On HARD_ERROR & TRANSMIT_BEACON
* no RING.STATUS interrupt.
*/
#define DISABLE_SOFT_ERROR 0x0020 /* On SOFT_ERROR, no RING.STATUS
* interrupt.
*/
#define PASS_ADAPTER_MAC_FRAMES 0x0010 /* Passing unsupported MAC frames
* to system.
*/
#define PASS_ATTENTION_FRAMES 0x0008 /* All changed attention MAC frames are
* passed to the system.
*/
#define PAD_ROUTING_FIELD 0x0004 /* Routing field is padded to 18
* bytes.
*/
#define FRAME_HOLD 0x0002 /*Adapter waits for entire frame before
* initiating DMA transfer; otherwise:
* DMA transfer initiation if internal
* buffer filled.
*/
#define CONTENDER 0x0001 /* Adapter participates in the monitor
* contention process.
*/
#define PASS_BEACON_MAC_FRAMES 0x8000 /* Adapter passes beacon MAC frames
* to the system.
*/
#define EARLY_TOKEN_RELEASE 0x1000 /* Only valid in 16 Mbps operation;
* 0 = ETR. (no effect in 4 Mbps
* operation)
*/
#define COPY_ALL_MAC_FRAMES 0x0400 /* All MAC frames are copied to
* the system. (after OPEN: duplicate
* address test (DAT) MAC frame is
* first received frame copied to the
* system)
*/
#define COPY_ALL_NON_MAC_FRAMES 0x0200 /* All non MAC frames are copied to
* the system.
*/
#define PASS_FIRST_BUF_ONLY 0x0100 /* Passes only first internal buffer
* of each received frame; FrameSize
* of RPLs must contain internal
* BUFFER_SIZE bits for promiscous mode.
*/
#define ENABLE_FULL_DUPLEX_SELECTION 0x2000
/* Enable the use of full-duplex
* settings with bits in byte 22 in
* ocpl. (new feature in firmware
* version 3.09)
*/
/* Full-duplex settings */
#define OPEN_FULL_DUPLEX_OFF 0x0000
#define OPEN_FULL_DUPLEX_ON 0x00c0
#define OPEN_FULL_DUPLEX_AUTO 0x0080
#define PROD_ID_SIZE 18 /* Length of product ID. */
#define TX_FRAG_NUM 3 /* Number of fragments used in one TPL. */
#define TX_MORE_FRAGMENTS 0x8000 /* Bit set in DataCount to indicate more
* fragments following.
*/
/* XXX is there some better way to do this? */
#define ISA_MAX_ADDRESS 0x00ffffff
#define PCI_MAX_ADDRESS 0xffffffff
#pragma pack(1)
typedef struct {
u_int16_t OPENOptions;
u_int8_t NodeAddr[6]; /* Adapter node address; use ROM
* address
*/
u_int32_t GroupAddr; /* Multicast: high order
* bytes = 0xC000
*/
u_int32_t FunctAddr; /* High order bytes = 0xC000 */
__be16 RxListSize; /* RPL size: 0 (=26), 14, 20 or
* 26 bytes read by the adapter.
* (Depending on the number of
* fragments/list)
*/
__be16 TxListSize; /* TPL size */
__be16 BufSize; /* Is automatically rounded up to the
* nearest nK boundary.
*/
u_int16_t FullDuplex;
u_int16_t Reserved;
u_int8_t TXBufMin; /* Number of adapter buffers reserved
* for transmission a minimum of 2
* buffers must be allocated.
*/
u_int8_t TXBufMax; /* Maximum number of adapter buffers
* for transmit; a minimum of 2 buffers
* must be available for receive.
* Default: 6
*/
u_int16_t ProdIDAddr[2];/* Pointer to product ID. */
} OPB, *OPB_Ptr;
#pragma pack()
/*
* SCB: adapter commands enabled by the host system started by writing
* CMD_INTERRUPT_ADAPTER | CMD_EXECUTE (|SCB_REQUEST) to the SIFCMD IO
* register. (special case: | CMD_SYSTEM_IRQ for initialization)
*/
#pragma pack(1)
typedef struct {
u_int16_t CMD; /* Command code */
u_int16_t Parm[2]; /* Pointer to Command Parameter Block */
} SCB; /* System Command Block (32 bit physical address; big endian)*/
#pragma pack()
/*
* SSB: adapter command return status can be evaluated after COMMAND_STATUS
* adapter to system interrupt after reading SSB, the availability of the SSB
* has to be told the adapter by writing CMD_INTERRUPT_ADAPTER | CMD_SSB_CLEAR
* in the SIFCMD IO register.
*/
#pragma pack(1)
typedef struct {
u_int16_t STS; /* Status code */
u_int16_t Parm[3]; /* Parameter or pointer to Status Parameter
* Block.
*/
} SSB; /* System Status Block (big endian - physical address) */
#pragma pack()
typedef struct {
unsigned short BurnedInAddrPtr; /* Pointer to adapter burned in
* address. (BIA)
*/
unsigned short SoftwareLevelPtr;/* Pointer to software level data. */
unsigned short AdapterAddrPtr; /* Pointer to adapter addresses. */
unsigned short AdapterParmsPtr; /* Pointer to adapter parameters. */
unsigned short MACBufferPtr; /* Pointer to MAC buffer. (internal) */
unsigned short LLCCountersPtr; /* Pointer to LLC counters. */
unsigned short SpeedFlagPtr; /* Pointer to data rate flag.
* (4/16 Mbps)
*/
unsigned short AdapterRAMPtr; /* Pointer to adapter RAM found. (KB) */
} INTPTRS; /* Adapter internal pointers */
#pragma pack(1)
typedef struct {
u_int8_t Line_Error; /* Line error: code violation in
* frame or in a token, or FCS error.
*/
u_int8_t Internal_Error; /* IBM specific. (Reserved_1) */
u_int8_t Burst_Error;
u_int8_t ARI_FCI_Error; /* ARI/FCI bit zero in AMP or
* SMP MAC frame.
*/
u_int8_t AbortDelimeters; /* IBM specific. (Reserved_2) */
u_int8_t Reserved_3;
u_int8_t Lost_Frame_Error; /* Receive of end of transmitted
* frame failed.
*/
u_int8_t Rx_Congest_Error; /* Adapter in repeat mode has not
* enough buffer space to copy incoming
* frame.
*/
u_int8_t Frame_Copied_Error; /* ARI bit not zero in frame
* addressed to adapter.
*/
u_int8_t Frequency_Error; /* IBM specific. (Reserved_4) */
u_int8_t Token_Error; /* (active only in monitor station) */
u_int8_t Reserved_5;
u_int8_t DMA_Bus_Error; /* DMA bus errors not exceeding the
* abort thresholds.
*/
u_int8_t DMA_Parity_Error; /* DMA parity errors not exceeding
* the abort thresholds.
*/
} ERRORTAB; /* Adapter error counters */
#pragma pack()
/*--------------------- Send and Receive definitions -------------------*/
#pragma pack(1)
typedef struct {
__be16 DataCount; /* Value 0, even and odd values are
* permitted; value is unaltered most
* significant bit set: following
* fragments last fragment: most
* significant bit is not evaluated.
* (???)
*/
__be32 DataAddr; /* Pointer to frame data fragment;
* even or odd.
*/
} Fragment;
#pragma pack()
#define MAX_FRAG_NUMBERS 9 /* Maximal number of fragments possible to use
* in one RPL/TPL. (depending on TI firmware
* version)
*/
/*
* AC (1), FC (1), Dst (6), Src (6), RIF (18), Data (4472) = 4504
* The packet size can be one of the follows: 548, 1502, 2084, 4504, 8176,
* 11439, 17832. Refer to TMS380 Second Generation Token Ring User's Guide
* Page 2-27.
*/
#define HEADER_SIZE (1 + 1 + 6 + 6)
#define SRC_SIZE 18
#define MIN_DATA_SIZE 516
#define DEFAULT_DATA_SIZE 4472
#define MAX_DATA_SIZE 17800
#define DEFAULT_PACKET_SIZE (HEADER_SIZE + SRC_SIZE + DEFAULT_DATA_SIZE)
#define MIN_PACKET_SIZE (HEADER_SIZE + SRC_SIZE + MIN_DATA_SIZE)
#define MAX_PACKET_SIZE (HEADER_SIZE + SRC_SIZE + MAX_DATA_SIZE)
/*
* Macros to deal with the frame status field.
*/
#define AC_NOT_RECOGNIZED 0x00
#define GROUP_BIT 0x80
#define GET_TRANSMIT_STATUS_HIGH_BYTE(Ts) ((unsigned char)((Ts) >> 8))
#define GET_FRAME_STATUS_HIGH_AC(Fs) ((unsigned char)(((Fs) & 0xC0) >> 6))
#define GET_FRAME_STATUS_LOW_AC(Fs) ((unsigned char)(((Fs) & 0x0C) >> 2))
#define DIRECTED_FRAME(Context) (!((Context)->MData[2] & GROUP_BIT))
/*--------------------- Send Functions ---------------------------------*/
/* define TX_CSTAT _REQUEST (R) and _COMPLETE (C) values (high-low) */
#define TX_VALID 0x0080 /* R: set via TRANSMIT.VALID interrupt.
* C: always reset to zero!
*/
#define TX_FRAME_COMPLETE 0x0040 /* R: must be reset to zero.
* C: set to one.
*/
#define TX_START_FRAME 0x0020 /* R: start of a frame: 1
* C: unchanged.
*/
#define TX_END_FRAME 0x0010 /* R: end of a frame: 1
* C: unchanged.
*/
#define TX_FRAME_IRQ 0x0008 /* R: request interrupt generation
* after transmission.
* C: unchanged.
*/
#define TX_ERROR 0x0004 /* R: reserved.
* C: set to one if Error occurred.
*/
#define TX_INTERFRAME_WAIT 0x0004
#define TX_PASS_CRC 0x0002 /* R: set if CRC value is already
* calculated. (valid only in
* FRAME_START TPL)
* C: unchanged.
*/
#define TX_PASS_SRC_ADDR 0x0001 /* R: adapter uses explicit frame
* source address and does not overwrite
* with the adapter node address.
* (valid only in FRAME_START TPL)
*
* C: unchanged.
*/
#define TX_STRIP_FS 0xFF00 /* R: reserved.
* C: if no Transmission Error,
* field contains copy of FS byte after
* stripping of frame.
*/
/*
* Structure of Transmit Parameter Lists (TPLs) (only one frame every TPL,
* but possibly multiple TPLs for one frame) the length of the TPLs has to be
* initialized in the OPL. (OPEN parameter list)
*/
#define TPL_NUM 3 /* Number of Transmit Parameter Lists.
* !! MUST BE >= 3 !!
*/
#pragma pack(1)
typedef struct s_TPL TPL;
struct s_TPL { /* Transmit Parameter List (align on even word boundaries) */
__be32 NextTPLAddr; /* Pointer to next TPL in chain; if
* pointer is odd: this is the last
* TPL. Pointing to itself can cause
* problems!
*/
volatile u_int16_t Status; /* Initialized by the adapter:
* CSTAT_REQUEST important: update least
* significant bit first! Set by the
* adapter: CSTAT_COMPLETE status.
*/
__be16 FrameSize; /* Number of bytes to be transmitted
* as a frame including AC/FC,
* Destination, Source, Routing field
* not including CRC, FS, End Delimiter
* (valid only if START_FRAME bit in
* CSTAT nonzero) must not be zero in
* any list; maximum value: (BUFFER_SIZE
* - 8) * TX_BUF_MAX sum of DataCount
* values in FragmentList must equal
* Frame_Size value in START_FRAME TPL!
* frame data fragment list.
*/
/* TPL/RPL size in OPEN parameter list depending on maximal
* numbers of fragments used in one parameter list.
*/
Fragment FragList[TX_FRAG_NUM]; /* Maximum: nine frame fragments in one
* TPL actual version of firmware: 9
* fragments possible.
*/
#pragma pack()
/* Special proprietary data and precalculations */
TPL *NextTPLPtr; /* Pointer to next TPL in chain. */
unsigned char *MData;
struct sk_buff *Skb;
unsigned char TPLIndex;
volatile unsigned char BusyFlag;/* Flag: TPL busy? */
dma_addr_t DMABuff; /* DMA IO bus address from dma_map */
};
/* ---------------------Receive Functions-------------------------------*
* define RECEIVE_CSTAT_REQUEST (R) and RECEIVE_CSTAT_COMPLETE (C) values.
* (high-low)
*/
#define RX_VALID 0x0080 /* R: set; tell adapter with
* RECEIVE.VALID interrupt.
* C: reset to zero.
*/
#define RX_FRAME_COMPLETE 0x0040 /* R: must be reset to zero,
* C: set to one.
*/
#define RX_START_FRAME 0x0020 /* R: must be reset to zero.
* C: set to one on the list.
*/
#define RX_END_FRAME 0x0010 /* R: must be reset to zero.
* C: set to one on the list
* that ends the frame.
*/
#define RX_FRAME_IRQ 0x0008 /* R: request interrupt generation
* after receive.
* C: unchanged.
*/
#define RX_INTERFRAME_WAIT 0x0004 /* R: after receiving a frame:
* interrupt and wait for a
* RECEIVE.CONTINUE.
* C: unchanged.
*/
#define RX_PASS_CRC 0x0002 /* R: if set, the adapter includes
* the CRC in data passed. (last four
* bytes; valid only if FRAME_START is
* set)
* C: set, if CRC is included in
* received data.
*/
#define RX_PASS_SRC_ADDR 0x0001 /* R: adapter uses explicit frame
* source address and does not
* overwrite with the adapter node
* address. (valid only if FRAME_START
* is set)
* C: unchanged.
*/
#define RX_RECEIVE_FS 0xFC00 /* R: reserved; must be reset to zero.
* C: on lists with START_FRAME, field
* contains frame status field from
* received frame; otherwise cleared.
*/
#define RX_ADDR_MATCH 0x0300 /* R: reserved; must be reset to zero.
* C: address match code mask.
*/
#define RX_STATUS_MASK 0x00FF /* Mask for receive status bits. */
#define RX_INTERN_ADDR_MATCH 0x0100 /* C: internally address match. */
#define RX_EXTERN_ADDR_MATCH 0x0200 /* C: externally matched via
* XMATCH/XFAIL interface.
*/
#define RX_INTEXT_ADDR_MATCH 0x0300 /* C: internally and externally
* matched.
*/
#define RX_READY (RX_VALID | RX_FRAME_IRQ) /* Ready for receive. */
/* Constants for Command Status Interrupt.
* COMMAND_REJECT status field bit functions (SSB.Parm[0])
*/
#define ILLEGAL_COMMAND 0x0080 /* Set if an unknown command
* is issued to the adapter
*/
#define ADDRESS_ERROR 0x0040 /* Set if any address field in
* the SCB is odd. (not word aligned)
*/
#define ADAPTER_OPEN 0x0020 /* Command issued illegal with
* open adapter.
*/
#define ADAPTER_CLOSE 0x0010 /* Command issued illegal with
* closed adapter.
*/
#define SAME_COMMAND 0x0008 /* Command issued with same command
* already executing.
*/
/* OPEN_COMPLETION values (SSB.Parm[0], MSB) */
#define NODE_ADDR_ERROR 0x0040 /* Wrong address or BIA read
* zero address.
*/
#define LIST_SIZE_ERROR 0x0020 /* If List_Size value not in 0,
* 14, 20, 26.
*/
#define BUF_SIZE_ERROR 0x0010 /* Not enough available memory for
* two buffers.
*/
#define TX_BUF_COUNT_ERROR 0x0004 /* Remaining receive buffers less than
* two.
*/
#define OPEN_ERROR 0x0002 /* Error during ring insertion; more
* information in bits 8-15.
*/
/* Standard return codes */
#define GOOD_COMPLETION 0x0080 /* =OPEN_SUCCESSFULL */
#define INVALID_OPEN_OPTION 0x0001 /* OPEN options are not supported by
* the adapter.
*/
/* OPEN phases; details of OPEN_ERROR (SSB.Parm[0], LSB) */
#define OPEN_PHASES_MASK 0xF000 /* Check only the bits 8-11. */
#define LOBE_MEDIA_TEST 0x1000
#define PHYSICAL_INSERTION 0x2000
#define ADDRESS_VERIFICATION 0x3000
#define PARTICIPATION_IN_RING_POLL 0x4000
#define REQUEST_INITIALISATION 0x5000
#define FULLDUPLEX_CHECK 0x6000
/* OPEN error codes; details of OPEN_ERROR (SSB.Parm[0], LSB) */
#define OPEN_ERROR_CODES_MASK 0x0F00 /* Check only the bits 12-15. */
#define OPEN_FUNCTION_FAILURE 0x0100 /* Unable to transmit to itself or
* frames received before insertion.
*/
#define OPEN_SIGNAL_LOSS 0x0200 /* Signal loss condition detected at
* receiver.
*/
#define OPEN_TIMEOUT 0x0500 /* Insertion timer expired before
* logical insertion.
*/
#define OPEN_RING_FAILURE 0x0600 /* Unable to receive own ring purge
* MAC frames.
*/
#define OPEN_RING_BEACONING 0x0700 /* Beacon MAC frame received after
* ring insertion.
*/
#define OPEN_DUPLICATE_NODEADDR 0x0800 /* Other station in ring found
* with the same address.
*/
#define OPEN_REQUEST_INIT 0x0900 /* RPS present but does not respond. */
#define OPEN_REMOVE_RECEIVED 0x0A00 /* Adapter received a remove adapter
* MAC frame.
*/
#define OPEN_FULLDUPLEX_SET 0x0D00 /* Got this with full duplex on when
* trying to connect to a normal ring.
*/
/* SET_BRIDGE_PARMS return codes: */
#define BRIDGE_INVALID_MAX_LEN 0x4000 /* MAX_ROUTING_FIELD_LENGTH odd,
* less than 6 or > 30.
*/
#define BRIDGE_INVALID_SRC_RING 0x2000 /* SOURCE_RING number zero, too large
* or = TARGET_RING.
*/
#define BRIDGE_INVALID_TRG_RING 0x1000 /* TARGET_RING number zero, too large
* or = SOURCE_RING.
*/
#define BRIDGE_INVALID_BRDGE_NO 0x0800 /* BRIDGE_NUMBER too large. */
#define BRIDGE_INVALID_OPTIONS 0x0400 /* Invalid bridge options. */
#define BRIDGE_DIAGS_FAILED 0x0200 /* Diagnostics of TMS380SRA failed. */
#define BRIDGE_NO_SRA 0x0100 /* The TMS380SRA does not exist in HW
* configuration.
*/
/*
* Bring Up Diagnostics error codes.
*/
#define BUD_INITIAL_ERROR 0x0
#define BUD_CHECKSUM_ERROR 0x1
#define BUD_ADAPTER_RAM_ERROR 0x2
#define BUD_INSTRUCTION_ERROR 0x3
#define BUD_CONTEXT_ERROR 0x4
#define BUD_PROTOCOL_ERROR 0x5
#define BUD_INTERFACE_ERROR 0x6
/* BUD constants */
#define BUD_MAX_RETRIES 3
#define BUD_MAX_LOOPCNT 6
#define BUD_TIMEOUT 3000
/* Initialization constants */
#define INIT_MAX_RETRIES 3 /* Maximum three retries. */
#define INIT_MAX_LOOPCNT 22 /* Maximum loop counts. */
/* RING STATUS field values (high/low) */
#define SIGNAL_LOSS 0x0080 /* Loss of signal on the ring
* detected.
*/
#define HARD_ERROR 0x0040 /* Transmitting or receiving beacon
* frames.
*/
#define SOFT_ERROR 0x0020 /* Report error MAC frame
* transmitted.
*/
#define TRANSMIT_BEACON 0x0010 /* Transmitting beacon frames on the
* ring.
*/
#define LOBE_WIRE_FAULT 0x0008 /* Open or short circuit in the
* cable to concentrator; adapter
* closed.
*/
#define AUTO_REMOVAL_ERROR 0x0004 /* Lobe wrap test failed, deinserted;
* adapter closed.
*/
#define REMOVE_RECEIVED 0x0001 /* Received a remove ring station MAC
* MAC frame request; adapter closed.
*/
#define COUNTER_OVERFLOW 0x8000 /* Overflow of one of the adapters
* error counters; READ.ERROR.LOG.
*/
#define SINGLE_STATION 0x4000 /* Adapter is the only station on the
* ring.
*/
#define RING_RECOVERY 0x2000 /* Claim token MAC frames on the ring;
* reset after ring purge frame.
*/
#define ADAPTER_CLOSED (LOBE_WIRE_FAULT | AUTO_REMOVAL_ERROR |\
REMOVE_RECEIVED)
/* Adapter_check_block.Status field bit assignments: */
#define DIO_PARITY 0x8000 /* Adapter detects bad parity
* through direct I/O access.
*/
#define DMA_READ_ABORT 0x4000 /* Aborting DMA read operation
* from system Parm[0]: 0=timeout,
* 1=parity error, 2=bus error;
* Parm[1]: 32 bit pointer to host
* system address at failure.
*/
#define DMA_WRITE_ABORT 0x2000 /* Aborting DMA write operation
* to system. (parameters analogous to
* DMA_READ_ABORT)
*/
#define ILLEGAL_OP_CODE 0x1000 /* Illegal operation code in the
* the adapters firmware Parm[0]-2:
* communications processor registers
* R13-R15.
*/
#define PARITY_ERRORS 0x0800 /* Adapter detects internal bus
* parity error.
*/
#define RAM_DATA_ERROR 0x0080 /* Valid only during RAM testing;
* RAM data error Parm[0-1]: 32 bit
* pointer to RAM location.
*/
#define RAM_PARITY_ERROR 0x0040 /* Valid only during RAM testing;
* RAM parity error Parm[0-1]: 32 bit
* pointer to RAM location.
*/
#define RING_UNDERRUN 0x0020 /* Internal DMA underrun when
* transmitting onto ring.
*/
#define INVALID_IRQ 0x0008 /* Unrecognized interrupt generated
* internal to adapter Parm[0-2]:
* adapter register R13-R15.
*/
#define INVALID_ERROR_IRQ 0x0004 /* Unrecognized error interrupt
* generated Parm[0-2]: adapter register
* R13-R15.
*/
#define INVALID_XOP 0x0002 /* Unrecognized XOP request in
* communication processor Parm[0-2]:
* adapter register R13-R15.
*/
#define CHECKADDR 0x05E0 /* Adapter check status information
* address offset.
*/
#define ROM_PAGE_0 0x0000 /* Adapter ROM page 0. */
/*
* RECEIVE.STATUS interrupt result SSB values: (high-low)
* (RECEIVE_COMPLETE field bit definitions in SSB.Parm[0])
*/
#define RX_COMPLETE 0x0080 /* SSB.Parm[0]; SSB.Parm[1]: 32
* bit pointer to last RPL.
*/
#define RX_SUSPENDED 0x0040 /* SSB.Parm[0]; SSB.Parm[1]: 32
* bit pointer to RPL with odd
* forward pointer.
*/
/* Valid receive CSTAT: */
#define RX_FRAME_CONTROL_BITS (RX_VALID | RX_START_FRAME | RX_END_FRAME | \
RX_FRAME_COMPLETE)
#define VALID_SINGLE_BUFFER_FRAME (RX_START_FRAME | RX_END_FRAME | \
RX_FRAME_COMPLETE)
typedef enum SKB_STAT SKB_STAT;
enum SKB_STAT {
SKB_UNAVAILABLE,
SKB_DMA_DIRECT,
SKB_DATA_COPY
};
/* Receive Parameter List (RPL) The length of the RPLs has to be initialized
* in the OPL. (OPEN parameter list)
*/
#define RPL_NUM 3
#define RX_FRAG_NUM 1 /* Maximal number of used fragments in one RPL.
* (up to firmware v2.24: 3, now: up to 9)
*/
#pragma pack(1)
typedef struct s_RPL RPL;
struct s_RPL { /* Receive Parameter List */
__be32 NextRPLAddr; /* Pointer to next RPL in chain
* (normalized = physical 32 bit
* address) if pointer is odd: this
* is last RPL. Pointing to itself can
* cause problems!
*/
volatile u_int16_t Status; /* Set by creation of Receive Parameter
* List RECEIVE_CSTAT_COMPLETE set by
* adapter in lists that start or end
* a frame.
*/
volatile __be16 FrameSize; /* Number of bytes received as a
* frame including AC/FC, Destination,
* Source, Routing field not including
* CRC, FS (Frame Status), End Delimiter
* (valid only if START_FRAME bit in
* CSTAT nonzero) must not be zero in
* any list; maximum value: (BUFFER_SIZE
* - 8) * TX_BUF_MAX sum of DataCount
* values in FragmentList must equal
* Frame_Size value in START_FRAME TPL!
* frame data fragment list
*/
/* TPL/RPL size in OPEN parameter list depending on maximal numbers
* of fragments used in one parameter list.
*/
Fragment FragList[RX_FRAG_NUM]; /* Maximum: nine frame fragments in
* one TPL. Actual version of firmware:
* 9 fragments possible.
*/
#pragma pack()
/* Special proprietary data and precalculations. */
RPL *NextRPLPtr; /* Logical pointer to next RPL in chain. */
unsigned char *MData;
struct sk_buff *Skb;
SKB_STAT SkbStat;
int RPLIndex;
dma_addr_t DMABuff; /* DMA IO bus address from dma_map */
};
/* Information that need to be kept for each board. */
typedef struct net_local {
#pragma pack(1)
IPB ipb; /* Initialization Parameter Block. */
SCB scb; /* System Command Block: system to adapter
* communication.
*/
SSB ssb; /* System Status Block: adapter to system
* communication.
*/
OPB ocpl; /* Open Options Parameter Block. */
ERRORTAB errorlogtable; /* Adapter statistic error counters.
* (read from adapter memory)
*/
unsigned char ProductID[PROD_ID_SIZE + 1]; /* Product ID */
#pragma pack()
TPL Tpl[TPL_NUM];
TPL *TplFree;
TPL *TplBusy;
unsigned char LocalTxBuffers[TPL_NUM][DEFAULT_PACKET_SIZE];
RPL Rpl[RPL_NUM];
RPL *RplHead;
RPL *RplTail;
unsigned char LocalRxBuffers[RPL_NUM][DEFAULT_PACKET_SIZE];
struct device *pdev;
int DataRate;
unsigned char ScbInUse;
unsigned short CMDqueue;
unsigned long AdapterOpenFlag:1;
unsigned long AdapterVirtOpenFlag:1;
unsigned long OpenCommandIssued:1;
unsigned long TransmitCommandActive:1;
unsigned long TransmitHaltScheduled:1;
unsigned long HaltInProgress:1;
unsigned long LobeWireFaultLogged:1;
unsigned long ReOpenInProgress:1;
unsigned long Sleeping:1;
unsigned long LastOpenStatus;
unsigned short CurrentRingStatus;
unsigned long MaxPacketSize;
unsigned long StartTime;
unsigned long LastSendTime;
struct tr_statistics MacStat; /* MAC statistics structure */
unsigned long dmalimit; /* the max DMA address (ie, ISA) */
dma_addr_t dmabuffer; /* the DMA bus address corresponding to
priv. Might be different from virt_to_bus()
for architectures with IO MMU (Alpha) */
struct timer_list timer;
wait_queue_head_t wait_for_tok_int;
INTPTRS intptrs; /* Internal adapter pointer. Must be read
* before OPEN command.
*/
unsigned short (*setnselout)(struct net_device *);
unsigned short (*sifreadb)(struct net_device *, unsigned short);
void (*sifwriteb)(struct net_device *, unsigned short, unsigned short);
unsigned short (*sifreadw)(struct net_device *, unsigned short);
void (*sifwritew)(struct net_device *, unsigned short, unsigned short);
spinlock_t lock; /* SMP protection */
void *tmspriv;
} NET_LOCAL;
#endif /* __KERNEL__ */
#endif /* __LINUX_TMS380TR_H */
Reference in New Issue View Git Blame Copy Permalink