mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-16 16:54:20 +08:00
6835d09ad2
This patch removes some obviously dead code found by the Coverity checker. Signed-off-by: Adrian Bunk <bunk@stusta.de>
2002 lines
52 KiB
C
2002 lines
52 KiB
C
/* ewrk3.c: A DIGITAL EtherWORKS 3 ethernet driver for Linux.
|
||
|
||
Written 1994 by David C. Davies.
|
||
|
||
Copyright 1994 Digital Equipment Corporation.
|
||
|
||
This software may be used and distributed according to the terms of
|
||
the GNU General Public License, incorporated herein by reference.
|
||
|
||
This driver is written for the Digital Equipment Corporation series
|
||
of EtherWORKS ethernet cards:
|
||
|
||
DE203 Turbo (BNC)
|
||
DE204 Turbo (TP)
|
||
DE205 Turbo (TP BNC)
|
||
|
||
The driver has been tested on a relatively busy network using the DE205
|
||
card and benchmarked with 'ttcp': it transferred 16M of data at 975kB/s
|
||
(7.8Mb/s) to a DECstation 5000/200.
|
||
|
||
The author may be reached at davies@maniac.ultranet.com.
|
||
|
||
=========================================================================
|
||
This driver has been written substantially from scratch, although its
|
||
inheritance of style and stack interface from 'depca.c' and in turn from
|
||
Donald Becker's 'lance.c' should be obvious.
|
||
|
||
The DE203/4/5 boards all use a new proprietary chip in place of the
|
||
LANCE chip used in prior cards (DEPCA, DE100, DE200/1/2, DE210, DE422).
|
||
Use the depca.c driver in the standard distribution for the LANCE based
|
||
cards from DIGITAL; this driver will not work with them.
|
||
|
||
The DE203/4/5 cards have 2 main modes: shared memory and I/O only. I/O
|
||
only makes all the card accesses through I/O transactions and no high
|
||
(shared) memory is used. This mode provides a >48% performance penalty
|
||
and is deprecated in this driver, although allowed to provide initial
|
||
setup when hardstrapped.
|
||
|
||
The shared memory mode comes in 3 flavours: 2kB, 32kB and 64kB. There is
|
||
no point in using any mode other than the 2kB mode - their performances
|
||
are virtually identical, although the driver has been tested in the 2kB
|
||
and 32kB modes. I would suggest you uncomment the line:
|
||
|
||
FORCE_2K_MODE;
|
||
|
||
to allow the driver to configure the card as a 2kB card at your current
|
||
base address, thus leaving more room to clutter your system box with
|
||
other memory hungry boards.
|
||
|
||
As many ISA and EISA cards can be supported under this driver as you
|
||
wish, limited primarily by the available IRQ lines, rather than by the
|
||
available I/O addresses (24 ISA, 16 EISA). I have checked different
|
||
configurations of multiple depca cards and ewrk3 cards and have not
|
||
found a problem yet (provided you have at least depca.c v0.38) ...
|
||
|
||
The board IRQ setting must be at an unused IRQ which is auto-probed
|
||
using Donald Becker's autoprobe routines. All these cards are at
|
||
{5,10,11,15}.
|
||
|
||
No 16MB memory limitation should exist with this driver as DMA is not
|
||
used and the common memory area is in low memory on the network card (my
|
||
current system has 20MB and I've not had problems yet).
|
||
|
||
The ability to load this driver as a loadable module has been included
|
||
and used extensively during the driver development (to save those long
|
||
reboot sequences). To utilise this ability, you have to do 8 things:
|
||
|
||
0) have a copy of the loadable modules code installed on your system.
|
||
1) copy ewrk3.c from the /linux/drivers/net directory to your favourite
|
||
temporary directory.
|
||
2) edit the source code near line 1898 to reflect the I/O address and
|
||
IRQ you're using.
|
||
3) compile ewrk3.c, but include -DMODULE in the command line to ensure
|
||
that the correct bits are compiled (see end of source code).
|
||
4) if you are wanting to add a new card, goto 5. Otherwise, recompile a
|
||
kernel with the ewrk3 configuration turned off and reboot.
|
||
5) insmod ewrk3.o
|
||
[Alan Cox: Changed this so you can insmod ewrk3.o irq=x io=y]
|
||
[Adam Kropelin: now accepts irq=x1,x2 io=y1,y2 for multiple cards]
|
||
6) run the net startup bits for your new eth?? interface manually
|
||
(usually /etc/rc.inet[12] at boot time).
|
||
7) enjoy!
|
||
|
||
Note that autoprobing is not allowed in loadable modules - the system is
|
||
already up and running and you're messing with interrupts.
|
||
|
||
To unload a module, turn off the associated interface
|
||
'ifconfig eth?? down' then 'rmmod ewrk3'.
|
||
|
||
Promiscuous mode has been turned off in this driver, but all the
|
||
multicast address bits have been turned on. This improved the send
|
||
performance on a busy network by about 13%.
|
||
|
||
Ioctl's have now been provided (primarily because I wanted to grab some
|
||
packet size statistics). They are patterned after 'plipconfig.c' from a
|
||
suggestion by Alan Cox. Using these ioctls, you can enable promiscuous
|
||
mode, add/delete multicast addresses, change the hardware address, get
|
||
packet size distribution statistics and muck around with the control and
|
||
status register. I'll add others if and when the need arises.
|
||
|
||
TO DO:
|
||
------
|
||
|
||
|
||
Revision History
|
||
----------------
|
||
|
||
Version Date Description
|
||
|
||
0.1 26-aug-94 Initial writing. ALPHA code release.
|
||
0.11 31-aug-94 Fixed: 2k mode memory base calc.,
|
||
LeMAC version calc.,
|
||
IRQ vector assignments during autoprobe.
|
||
0.12 31-aug-94 Tested working on LeMAC2 (DE20[345]-AC) card.
|
||
Fixed up MCA hash table algorithm.
|
||
0.20 4-sep-94 Added IOCTL functionality.
|
||
0.21 14-sep-94 Added I/O mode.
|
||
0.21axp 15-sep-94 Special version for ALPHA AXP Linux V1.0.
|
||
0.22 16-sep-94 Added more IOCTLs & tidied up.
|
||
0.23 21-sep-94 Added transmit cut through.
|
||
0.24 31-oct-94 Added uid checks in some ioctls.
|
||
0.30 1-nov-94 BETA code release.
|
||
0.31 5-dec-94 Added check/allocate region code.
|
||
0.32 16-jan-95 Broadcast packet fix.
|
||
0.33 10-Feb-95 Fix recognition bug reported by <bkm@star.rl.ac.uk>.
|
||
0.40 27-Dec-95 Rationalise MODULE and autoprobe code.
|
||
Rewrite for portability & updated.
|
||
ALPHA support from <jestabro@amt.tay1.dec.com>
|
||
Added verify_area() calls in ewrk3_ioctl() from
|
||
suggestion by <heiko@colossus.escape.de>.
|
||
Add new multicasting code.
|
||
0.41 20-Jan-96 Fix IRQ set up problem reported by
|
||
<kenneth@bbs.sas.ntu.ac.sg>.
|
||
0.42 22-Apr-96 Fix alloc_device() bug <jari@markkus2.fimr.fi>
|
||
0.43 16-Aug-96 Update alloc_device() to conform to de4x5.c
|
||
0.44 08-Nov-01 use library crc32 functions <Matt_Domsch@dell.com>
|
||
0.45 19-Jul-02 fix unaligned access on alpha <martin@bruli.net>
|
||
0.46 10-Oct-02 Multiple NIC support when module <akropel1@rochester.rr.com>
|
||
0.47 18-Oct-02 ethtool support <akropel1@rochester.rr.com>
|
||
0.48 18-Oct-02 cli/sti removal for 2.5 <vda@port.imtp.ilyichevsk.odessa.ua>
|
||
ioctl locking, signature search cleanup <akropel1@rochester.rr.com>
|
||
|
||
=========================================================================
|
||
*/
|
||
|
||
#include <linux/module.h>
|
||
#include <linux/kernel.h>
|
||
#include <linux/string.h>
|
||
#include <linux/errno.h>
|
||
#include <linux/ioport.h>
|
||
#include <linux/slab.h>
|
||
#include <linux/interrupt.h>
|
||
#include <linux/delay.h>
|
||
#include <linux/init.h>
|
||
#include <linux/crc32.h>
|
||
#include <linux/netdevice.h>
|
||
#include <linux/etherdevice.h>
|
||
#include <linux/skbuff.h>
|
||
#include <linux/ethtool.h>
|
||
#include <linux/time.h>
|
||
#include <linux/types.h>
|
||
#include <linux/unistd.h>
|
||
#include <linux/ctype.h>
|
||
#include <linux/bitops.h>
|
||
|
||
#include <asm/io.h>
|
||
#include <asm/dma.h>
|
||
#include <asm/uaccess.h>
|
||
|
||
#include "ewrk3.h"
|
||
|
||
#define DRV_NAME "ewrk3"
|
||
#define DRV_VERSION "0.48"
|
||
|
||
static char version[] __initdata =
|
||
DRV_NAME ":v" DRV_VERSION " 2002/10/18 davies@maniac.ultranet.com\n";
|
||
|
||
#ifdef EWRK3_DEBUG
|
||
static int ewrk3_debug = EWRK3_DEBUG;
|
||
#else
|
||
static int ewrk3_debug = 1;
|
||
#endif
|
||
|
||
#define EWRK3_NDA 0xffe0 /* No Device Address */
|
||
|
||
#define PROBE_LENGTH 32
|
||
#define ETH_PROM_SIG 0xAA5500FFUL
|
||
|
||
#ifndef EWRK3_SIGNATURE
|
||
#define EWRK3_SIGNATURE {"DE203","DE204","DE205",""}
|
||
#define EWRK3_STRLEN 8
|
||
#endif
|
||
|
||
#ifndef EWRK3_RAM_BASE_ADDRESSES
|
||
#define EWRK3_RAM_BASE_ADDRESSES {0xc0000,0xd0000,0x00000}
|
||
#endif
|
||
|
||
/*
|
||
** Sets up the I/O area for the autoprobe.
|
||
*/
|
||
#define EWRK3_IO_BASE 0x100 /* Start address for probe search */
|
||
#define EWRK3_IOP_INC 0x20 /* I/O address increment */
|
||
#define EWRK3_TOTAL_SIZE 0x20 /* required I/O address length */
|
||
|
||
#ifndef MAX_NUM_EWRK3S
|
||
#define MAX_NUM_EWRK3S 21
|
||
#endif
|
||
|
||
#ifndef EWRK3_EISA_IO_PORTS
|
||
#define EWRK3_EISA_IO_PORTS 0x0c00 /* I/O port base address, slot 0 */
|
||
#endif
|
||
|
||
#ifndef MAX_EISA_SLOTS
|
||
#define MAX_EISA_SLOTS 16
|
||
#define EISA_SLOT_INC 0x1000
|
||
#endif
|
||
|
||
#define QUEUE_PKT_TIMEOUT (1*HZ) /* Jiffies */
|
||
|
||
/*
|
||
** EtherWORKS 3 shared memory window sizes
|
||
*/
|
||
#define IO_ONLY 0x00
|
||
#define SHMEM_2K 0x800
|
||
#define SHMEM_32K 0x8000
|
||
#define SHMEM_64K 0x10000
|
||
|
||
/*
|
||
** EtherWORKS 3 IRQ ENABLE/DISABLE
|
||
*/
|
||
#define ENABLE_IRQs { \
|
||
icr |= lp->irq_mask;\
|
||
outb(icr, EWRK3_ICR); /* Enable the IRQs */\
|
||
}
|
||
|
||
#define DISABLE_IRQs { \
|
||
icr = inb(EWRK3_ICR);\
|
||
icr &= ~lp->irq_mask;\
|
||
outb(icr, EWRK3_ICR); /* Disable the IRQs */\
|
||
}
|
||
|
||
/*
|
||
** EtherWORKS 3 START/STOP
|
||
*/
|
||
#define START_EWRK3 { \
|
||
csr = inb(EWRK3_CSR);\
|
||
csr &= ~(CSR_TXD|CSR_RXD);\
|
||
outb(csr, EWRK3_CSR); /* Enable the TX and/or RX */\
|
||
}
|
||
|
||
#define STOP_EWRK3 { \
|
||
csr = (CSR_TXD|CSR_RXD);\
|
||
outb(csr, EWRK3_CSR); /* Disable the TX and/or RX */\
|
||
}
|
||
|
||
/*
|
||
** The EtherWORKS 3 private structure
|
||
*/
|
||
#define EWRK3_PKT_STAT_SZ 16
|
||
#define EWRK3_PKT_BIN_SZ 128 /* Should be >=100 unless you
|
||
increase EWRK3_PKT_STAT_SZ */
|
||
|
||
struct ewrk3_stats {
|
||
u32 bins[EWRK3_PKT_STAT_SZ];
|
||
u32 unicast;
|
||
u32 multicast;
|
||
u32 broadcast;
|
||
u32 excessive_collisions;
|
||
u32 tx_underruns;
|
||
u32 excessive_underruns;
|
||
};
|
||
|
||
struct ewrk3_private {
|
||
char adapter_name[80]; /* Name exported to /proc/ioports */
|
||
u_long shmem_base; /* Shared memory start address */
|
||
void __iomem *shmem;
|
||
u_long shmem_length; /* Shared memory window length */
|
||
struct net_device_stats stats; /* Public stats */
|
||
struct ewrk3_stats pktStats; /* Private stats counters */
|
||
u_char irq_mask; /* Adapter IRQ mask bits */
|
||
u_char mPage; /* Maximum 2kB Page number */
|
||
u_char lemac; /* Chip rev. level */
|
||
u_char hard_strapped; /* Don't allow a full open */
|
||
u_char txc; /* Transmit cut through */
|
||
void __iomem *mctbl; /* Pointer to the multicast table */
|
||
u_char led_mask; /* Used to reserve LED access for ethtool */
|
||
spinlock_t hw_lock;
|
||
};
|
||
|
||
/*
|
||
** Force the EtherWORKS 3 card to be in 2kB MODE
|
||
*/
|
||
#define FORCE_2K_MODE { \
|
||
shmem_length = SHMEM_2K;\
|
||
outb(((mem_start - 0x80000) >> 11), EWRK3_MBR);\
|
||
}
|
||
|
||
/*
|
||
** Public Functions
|
||
*/
|
||
static int ewrk3_open(struct net_device *dev);
|
||
static int ewrk3_queue_pkt(struct sk_buff *skb, struct net_device *dev);
|
||
static irqreturn_t ewrk3_interrupt(int irq, void *dev_id, struct pt_regs *regs);
|
||
static int ewrk3_close(struct net_device *dev);
|
||
static struct net_device_stats *ewrk3_get_stats(struct net_device *dev);
|
||
static void set_multicast_list(struct net_device *dev);
|
||
static int ewrk3_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
|
||
static struct ethtool_ops ethtool_ops_203;
|
||
static struct ethtool_ops ethtool_ops;
|
||
|
||
/*
|
||
** Private functions
|
||
*/
|
||
static int ewrk3_hw_init(struct net_device *dev, u_long iobase);
|
||
static void ewrk3_init(struct net_device *dev);
|
||
static int ewrk3_rx(struct net_device *dev);
|
||
static int ewrk3_tx(struct net_device *dev);
|
||
static void ewrk3_timeout(struct net_device *dev);
|
||
|
||
static void EthwrkSignature(char *name, char *eeprom_image);
|
||
static int DevicePresent(u_long iobase);
|
||
static void SetMulticastFilter(struct net_device *dev);
|
||
static int EISA_signature(char *name, s32 eisa_id);
|
||
|
||
static int Read_EEPROM(u_long iobase, u_char eaddr);
|
||
static int Write_EEPROM(short data, u_long iobase, u_char eaddr);
|
||
static u_char get_hw_addr(struct net_device *dev, u_char * eeprom_image, char chipType);
|
||
|
||
static int ewrk3_probe1(struct net_device *dev, u_long iobase, int irq);
|
||
static int isa_probe(struct net_device *dev, u_long iobase);
|
||
static int eisa_probe(struct net_device *dev, u_long iobase);
|
||
|
||
static u_char irq[MAX_NUM_EWRK3S+1] = {5, 0, 10, 3, 11, 9, 15, 12};
|
||
|
||
static char name[EWRK3_STRLEN + 1];
|
||
static int num_ewrks3s;
|
||
|
||
/*
|
||
** Miscellaneous defines...
|
||
*/
|
||
#define INIT_EWRK3 {\
|
||
outb(EEPROM_INIT, EWRK3_IOPR);\
|
||
mdelay(1);\
|
||
}
|
||
|
||
#ifndef MODULE
|
||
struct net_device * __init ewrk3_probe(int unit)
|
||
{
|
||
struct net_device *dev = alloc_etherdev(sizeof(struct ewrk3_private));
|
||
int err;
|
||
|
||
if (!dev)
|
||
return ERR_PTR(-ENOMEM);
|
||
|
||
if (unit >= 0) {
|
||
sprintf(dev->name, "eth%d", unit);
|
||
netdev_boot_setup_check(dev);
|
||
}
|
||
SET_MODULE_OWNER(dev);
|
||
|
||
err = ewrk3_probe1(dev, dev->base_addr, dev->irq);
|
||
if (err)
|
||
goto out;
|
||
return dev;
|
||
out:
|
||
free_netdev(dev);
|
||
return ERR_PTR(err);
|
||
|
||
}
|
||
#endif
|
||
|
||
static int __init ewrk3_probe1(struct net_device *dev, u_long iobase, int irq)
|
||
{
|
||
int err;
|
||
|
||
dev->base_addr = iobase;
|
||
dev->irq = irq;
|
||
|
||
/* Address PROM pattern */
|
||
err = isa_probe(dev, iobase);
|
||
if (err != 0)
|
||
err = eisa_probe(dev, iobase);
|
||
|
||
if (err)
|
||
return err;
|
||
|
||
err = register_netdev(dev);
|
||
if (err)
|
||
release_region(dev->base_addr, EWRK3_TOTAL_SIZE);
|
||
|
||
return err;
|
||
}
|
||
|
||
static int __init
|
||
ewrk3_hw_init(struct net_device *dev, u_long iobase)
|
||
{
|
||
struct ewrk3_private *lp;
|
||
int i, status = 0;
|
||
u_long mem_start, shmem_length;
|
||
u_char cr, cmr, icr, nicsr, lemac, hard_strapped = 0;
|
||
u_char eeprom_image[EEPROM_MAX], chksum, eisa_cr = 0;
|
||
|
||
/*
|
||
** Stop the EWRK3. Enable the DBR ROM. Disable interrupts and remote boot.
|
||
** This also disables the EISA_ENABLE bit in the EISA Control Register.
|
||
*/
|
||
if (iobase > 0x400)
|
||
eisa_cr = inb(EISA_CR);
|
||
INIT_EWRK3;
|
||
|
||
nicsr = inb(EWRK3_CSR);
|
||
|
||
icr = inb(EWRK3_ICR);
|
||
icr &= 0x70;
|
||
outb(icr, EWRK3_ICR); /* Disable all the IRQs */
|
||
|
||
if (nicsr == (CSR_TXD | CSR_RXD))
|
||
return -ENXIO;
|
||
|
||
|
||
/* Check that the EEPROM is alive and well and not living on Pluto... */
|
||
for (chksum = 0, i = 0; i < EEPROM_MAX; i += 2) {
|
||
union {
|
||
short val;
|
||
char c[2];
|
||
} tmp;
|
||
|
||
tmp.val = (short) Read_EEPROM(iobase, (i >> 1));
|
||
eeprom_image[i] = tmp.c[0];
|
||
eeprom_image[i + 1] = tmp.c[1];
|
||
chksum += eeprom_image[i] + eeprom_image[i + 1];
|
||
}
|
||
|
||
if (chksum != 0) { /* Bad EEPROM Data! */
|
||
printk("%s: Device has a bad on-board EEPROM.\n", dev->name);
|
||
return -ENXIO;
|
||
}
|
||
|
||
EthwrkSignature(name, eeprom_image);
|
||
if (*name == '\0')
|
||
return -ENXIO;
|
||
|
||
dev->base_addr = iobase;
|
||
|
||
if (iobase > 0x400) {
|
||
outb(eisa_cr, EISA_CR); /* Rewrite the EISA CR */
|
||
}
|
||
lemac = eeprom_image[EEPROM_CHIPVER];
|
||
cmr = inb(EWRK3_CMR);
|
||
|
||
if (((lemac == LeMAC) && ((cmr & CMR_NO_EEPROM) != CMR_NO_EEPROM)) ||
|
||
((lemac == LeMAC2) && !(cmr & CMR_HS))) {
|
||
printk("%s: %s at %#4lx", dev->name, name, iobase);
|
||
hard_strapped = 1;
|
||
} else if ((iobase & 0x0fff) == EWRK3_EISA_IO_PORTS) {
|
||
/* EISA slot address */
|
||
printk("%s: %s at %#4lx (EISA slot %ld)",
|
||
dev->name, name, iobase, ((iobase >> 12) & 0x0f));
|
||
} else { /* ISA port address */
|
||
printk("%s: %s at %#4lx", dev->name, name, iobase);
|
||
}
|
||
|
||
printk(", h/w address ");
|
||
if (lemac != LeMAC2)
|
||
DevicePresent(iobase); /* need after EWRK3_INIT */
|
||
status = get_hw_addr(dev, eeprom_image, lemac);
|
||
for (i = 0; i < ETH_ALEN - 1; i++) { /* get the ethernet addr. */
|
||
printk("%2.2x:", dev->dev_addr[i]);
|
||
}
|
||
printk("%2.2x,\n", dev->dev_addr[i]);
|
||
|
||
if (status) {
|
||
printk(" which has an EEPROM CRC error.\n");
|
||
return -ENXIO;
|
||
}
|
||
|
||
if (lemac == LeMAC2) { /* Special LeMAC2 CMR things */
|
||
cmr &= ~(CMR_RA | CMR_WB | CMR_LINK | CMR_POLARITY | CMR_0WS);
|
||
if (eeprom_image[EEPROM_MISC0] & READ_AHEAD)
|
||
cmr |= CMR_RA;
|
||
if (eeprom_image[EEPROM_MISC0] & WRITE_BEHIND)
|
||
cmr |= CMR_WB;
|
||
if (eeprom_image[EEPROM_NETMAN0] & NETMAN_POL)
|
||
cmr |= CMR_POLARITY;
|
||
if (eeprom_image[EEPROM_NETMAN0] & NETMAN_LINK)
|
||
cmr |= CMR_LINK;
|
||
if (eeprom_image[EEPROM_MISC0] & _0WS_ENA)
|
||
cmr |= CMR_0WS;
|
||
}
|
||
if (eeprom_image[EEPROM_SETUP] & SETUP_DRAM)
|
||
cmr |= CMR_DRAM;
|
||
outb(cmr, EWRK3_CMR);
|
||
|
||
cr = inb(EWRK3_CR); /* Set up the Control Register */
|
||
cr |= eeprom_image[EEPROM_SETUP] & SETUP_APD;
|
||
if (cr & SETUP_APD)
|
||
cr |= eeprom_image[EEPROM_SETUP] & SETUP_PS;
|
||
cr |= eeprom_image[EEPROM_MISC0] & FAST_BUS;
|
||
cr |= eeprom_image[EEPROM_MISC0] & ENA_16;
|
||
outb(cr, EWRK3_CR);
|
||
|
||
/*
|
||
** Determine the base address and window length for the EWRK3
|
||
** RAM from the memory base register.
|
||
*/
|
||
mem_start = inb(EWRK3_MBR);
|
||
shmem_length = 0;
|
||
if (mem_start != 0) {
|
||
if ((mem_start >= 0x0a) && (mem_start <= 0x0f)) {
|
||
mem_start *= SHMEM_64K;
|
||
shmem_length = SHMEM_64K;
|
||
} else if ((mem_start >= 0x14) && (mem_start <= 0x1f)) {
|
||
mem_start *= SHMEM_32K;
|
||
shmem_length = SHMEM_32K;
|
||
} else if ((mem_start >= 0x40) && (mem_start <= 0xff)) {
|
||
mem_start = mem_start * SHMEM_2K + 0x80000;
|
||
shmem_length = SHMEM_2K;
|
||
} else {
|
||
return -ENXIO;
|
||
}
|
||
}
|
||
/*
|
||
** See the top of this source code for comments about
|
||
** uncommenting this line.
|
||
*/
|
||
/* FORCE_2K_MODE; */
|
||
|
||
if (hard_strapped) {
|
||
printk(" is hard strapped.\n");
|
||
} else if (mem_start) {
|
||
printk(" has a %dk RAM window", (int) (shmem_length >> 10));
|
||
printk(" at 0x%.5lx", mem_start);
|
||
} else {
|
||
printk(" is in I/O only mode");
|
||
}
|
||
|
||
lp = netdev_priv(dev);
|
||
lp->shmem_base = mem_start;
|
||
lp->shmem = ioremap(mem_start, shmem_length);
|
||
if (!lp->shmem)
|
||
return -ENOMEM;
|
||
lp->shmem_length = shmem_length;
|
||
lp->lemac = lemac;
|
||
lp->hard_strapped = hard_strapped;
|
||
lp->led_mask = CR_LED;
|
||
spin_lock_init(&lp->hw_lock);
|
||
|
||
lp->mPage = 64;
|
||
if (cmr & CMR_DRAM)
|
||
lp->mPage <<= 1; /* 2 DRAMS on module */
|
||
|
||
sprintf(lp->adapter_name, "%s (%s)", name, dev->name);
|
||
|
||
lp->irq_mask = ICR_TNEM | ICR_TXDM | ICR_RNEM | ICR_RXDM;
|
||
|
||
if (!hard_strapped) {
|
||
/*
|
||
** Enable EWRK3 board interrupts for autoprobing
|
||
*/
|
||
icr |= ICR_IE; /* Enable interrupts */
|
||
outb(icr, EWRK3_ICR);
|
||
|
||
/* The DMA channel may be passed in on this parameter. */
|
||
dev->dma = 0;
|
||
|
||
/* To auto-IRQ we enable the initialization-done and DMA err,
|
||
interrupts. For now we will always get a DMA error. */
|
||
if (dev->irq < 2) {
|
||
#ifndef MODULE
|
||
u_char irqnum;
|
||
unsigned long irq_mask;
|
||
|
||
|
||
irq_mask = probe_irq_on();
|
||
|
||
/*
|
||
** Trigger a TNE interrupt.
|
||
*/
|
||
icr |= ICR_TNEM;
|
||
outb(1, EWRK3_TDQ); /* Write to the TX done queue */
|
||
outb(icr, EWRK3_ICR); /* Unmask the TXD interrupt */
|
||
|
||
irqnum = irq[((icr & IRQ_SEL) >> 4)];
|
||
|
||
mdelay(20);
|
||
dev->irq = probe_irq_off(irq_mask);
|
||
if ((dev->irq) && (irqnum == dev->irq)) {
|
||
printk(" and uses IRQ%d.\n", dev->irq);
|
||
} else {
|
||
if (!dev->irq) {
|
||
printk(" and failed to detect IRQ line.\n");
|
||
} else if ((irqnum == 1) && (lemac == LeMAC2)) {
|
||
printk(" and an illegal IRQ line detected.\n");
|
||
} else {
|
||
printk(", but incorrect IRQ line detected.\n");
|
||
}
|
||
iounmap(lp->shmem);
|
||
return -ENXIO;
|
||
}
|
||
|
||
DISABLE_IRQs; /* Mask all interrupts */
|
||
|
||
#endif /* MODULE */
|
||
} else {
|
||
printk(" and requires IRQ%d.\n", dev->irq);
|
||
}
|
||
}
|
||
|
||
if (ewrk3_debug > 1) {
|
||
printk(version);
|
||
}
|
||
/* The EWRK3-specific entries in the device structure. */
|
||
dev->open = ewrk3_open;
|
||
dev->hard_start_xmit = ewrk3_queue_pkt;
|
||
dev->stop = ewrk3_close;
|
||
dev->get_stats = ewrk3_get_stats;
|
||
dev->set_multicast_list = set_multicast_list;
|
||
dev->do_ioctl = ewrk3_ioctl;
|
||
if (lp->adapter_name[4] == '3')
|
||
SET_ETHTOOL_OPS(dev, ðtool_ops_203);
|
||
else
|
||
SET_ETHTOOL_OPS(dev, ðtool_ops);
|
||
dev->tx_timeout = ewrk3_timeout;
|
||
dev->watchdog_timeo = QUEUE_PKT_TIMEOUT;
|
||
|
||
dev->mem_start = 0;
|
||
|
||
return 0;
|
||
}
|
||
|
||
|
||
static int ewrk3_open(struct net_device *dev)
|
||
{
|
||
struct ewrk3_private *lp = netdev_priv(dev);
|
||
u_long iobase = dev->base_addr;
|
||
int i, status = 0;
|
||
u_char icr, csr;
|
||
|
||
/*
|
||
** Stop the TX and RX...
|
||
*/
|
||
STOP_EWRK3;
|
||
|
||
if (!lp->hard_strapped) {
|
||
if (request_irq(dev->irq, (void *) ewrk3_interrupt, 0, "ewrk3", dev)) {
|
||
printk("ewrk3_open(): Requested IRQ%d is busy\n", dev->irq);
|
||
status = -EAGAIN;
|
||
} else {
|
||
|
||
/*
|
||
** Re-initialize the EWRK3...
|
||
*/
|
||
ewrk3_init(dev);
|
||
|
||
if (ewrk3_debug > 1) {
|
||
printk("%s: ewrk3 open with irq %d\n", dev->name, dev->irq);
|
||
printk(" physical address: ");
|
||
for (i = 0; i < 5; i++) {
|
||
printk("%2.2x:", (u_char) dev->dev_addr[i]);
|
||
}
|
||
printk("%2.2x\n", (u_char) dev->dev_addr[i]);
|
||
if (lp->shmem_length == 0) {
|
||
printk(" no shared memory, I/O only mode\n");
|
||
} else {
|
||
printk(" start of shared memory: 0x%08lx\n", lp->shmem_base);
|
||
printk(" window length: 0x%04lx\n", lp->shmem_length);
|
||
}
|
||
printk(" # of DRAMS: %d\n", ((inb(EWRK3_CMR) & 0x02) ? 2 : 1));
|
||
printk(" csr: 0x%02x\n", inb(EWRK3_CSR));
|
||
printk(" cr: 0x%02x\n", inb(EWRK3_CR));
|
||
printk(" icr: 0x%02x\n", inb(EWRK3_ICR));
|
||
printk(" cmr: 0x%02x\n", inb(EWRK3_CMR));
|
||
printk(" fmqc: 0x%02x\n", inb(EWRK3_FMQC));
|
||
}
|
||
netif_start_queue(dev);
|
||
/*
|
||
** Unmask EWRK3 board interrupts
|
||
*/
|
||
icr = inb(EWRK3_ICR);
|
||
ENABLE_IRQs;
|
||
|
||
}
|
||
} else {
|
||
printk(KERN_ERR "%s: ewrk3 available for hard strapped set up only.\n", dev->name);
|
||
printk(KERN_ERR " Run the 'ewrk3setup' utility or remove the hard straps.\n");
|
||
return -EINVAL;
|
||
}
|
||
|
||
return status;
|
||
}
|
||
|
||
/*
|
||
** Initialize the EtherWORKS 3 operating conditions
|
||
*/
|
||
static void ewrk3_init(struct net_device *dev)
|
||
{
|
||
struct ewrk3_private *lp = netdev_priv(dev);
|
||
u_char csr, page;
|
||
u_long iobase = dev->base_addr;
|
||
int i;
|
||
|
||
/*
|
||
** Enable any multicasts
|
||
*/
|
||
set_multicast_list(dev);
|
||
|
||
/*
|
||
** Set hardware MAC address. Address is initialized from the EEPROM
|
||
** during startup but may have since been changed by the user.
|
||
*/
|
||
for (i=0; i<ETH_ALEN; i++)
|
||
outb(dev->dev_addr[i], EWRK3_PAR0 + i);
|
||
|
||
/*
|
||
** Clean out any remaining entries in all the queues here
|
||
*/
|
||
while (inb(EWRK3_TQ));
|
||
while (inb(EWRK3_TDQ));
|
||
while (inb(EWRK3_RQ));
|
||
while (inb(EWRK3_FMQ));
|
||
|
||
/*
|
||
** Write a clean free memory queue
|
||
*/
|
||
for (page = 1; page < lp->mPage; page++) { /* Write the free page numbers */
|
||
outb(page, EWRK3_FMQ); /* to the Free Memory Queue */
|
||
}
|
||
|
||
START_EWRK3; /* Enable the TX and/or RX */
|
||
}
|
||
|
||
/*
|
||
* Transmit timeout
|
||
*/
|
||
|
||
static void ewrk3_timeout(struct net_device *dev)
|
||
{
|
||
struct ewrk3_private *lp = netdev_priv(dev);
|
||
u_char icr, csr;
|
||
u_long iobase = dev->base_addr;
|
||
|
||
if (!lp->hard_strapped)
|
||
{
|
||
printk(KERN_WARNING"%s: transmit timed/locked out, status %04x, resetting.\n",
|
||
dev->name, inb(EWRK3_CSR));
|
||
|
||
/*
|
||
** Mask all board interrupts
|
||
*/
|
||
DISABLE_IRQs;
|
||
|
||
/*
|
||
** Stop the TX and RX...
|
||
*/
|
||
STOP_EWRK3;
|
||
|
||
ewrk3_init(dev);
|
||
|
||
/*
|
||
** Unmask EWRK3 board interrupts
|
||
*/
|
||
ENABLE_IRQs;
|
||
|
||
dev->trans_start = jiffies;
|
||
netif_wake_queue(dev);
|
||
}
|
||
}
|
||
|
||
/*
|
||
** Writes a socket buffer to the free page queue
|
||
*/
|
||
static int ewrk3_queue_pkt (struct sk_buff *skb, struct net_device *dev)
|
||
{
|
||
struct ewrk3_private *lp = netdev_priv(dev);
|
||
u_long iobase = dev->base_addr;
|
||
void __iomem *buf = NULL;
|
||
u_char icr;
|
||
u_char page;
|
||
|
||
spin_lock_irq (&lp->hw_lock);
|
||
DISABLE_IRQs;
|
||
|
||
/* if no resources available, exit, request packet be queued */
|
||
if (inb (EWRK3_FMQC) == 0) {
|
||
printk (KERN_WARNING "%s: ewrk3_queue_pkt(): No free resources...\n",
|
||
dev->name);
|
||
printk (KERN_WARNING "%s: ewrk3_queue_pkt(): CSR: %02x ICR: %02x FMQC: %02x\n",
|
||
dev->name, inb (EWRK3_CSR), inb (EWRK3_ICR),
|
||
inb (EWRK3_FMQC));
|
||
goto err_out;
|
||
}
|
||
|
||
/*
|
||
** Get a free page from the FMQ
|
||
*/
|
||
if ((page = inb (EWRK3_FMQ)) >= lp->mPage) {
|
||
printk ("ewrk3_queue_pkt(): Invalid free memory page (%d).\n",
|
||
(u_char) page);
|
||
goto err_out;
|
||
}
|
||
|
||
|
||
/*
|
||
** Set up shared memory window and pointer into the window
|
||
*/
|
||
if (lp->shmem_length == IO_ONLY) {
|
||
outb (page, EWRK3_IOPR);
|
||
} else if (lp->shmem_length == SHMEM_2K) {
|
||
buf = lp->shmem;
|
||
outb (page, EWRK3_MPR);
|
||
} else if (lp->shmem_length == SHMEM_32K) {
|
||
buf = (((short) page << 11) & 0x7800) + lp->shmem;
|
||
outb ((page >> 4), EWRK3_MPR);
|
||
} else if (lp->shmem_length == SHMEM_64K) {
|
||
buf = (((short) page << 11) & 0xf800) + lp->shmem;
|
||
outb ((page >> 5), EWRK3_MPR);
|
||
} else {
|
||
printk (KERN_ERR "%s: Oops - your private data area is hosed!\n",
|
||
dev->name);
|
||
BUG ();
|
||
}
|
||
|
||
/*
|
||
** Set up the buffer control structures and copy the data from
|
||
** the socket buffer to the shared memory .
|
||
*/
|
||
if (lp->shmem_length == IO_ONLY) {
|
||
int i;
|
||
u_char *p = skb->data;
|
||
outb ((char) (TCR_QMODE | TCR_PAD | TCR_IFC), EWRK3_DATA);
|
||
outb ((char) (skb->len & 0xff), EWRK3_DATA);
|
||
outb ((char) ((skb->len >> 8) & 0xff), EWRK3_DATA);
|
||
outb ((char) 0x04, EWRK3_DATA);
|
||
for (i = 0; i < skb->len; i++) {
|
||
outb (*p++, EWRK3_DATA);
|
||
}
|
||
outb (page, EWRK3_TQ); /* Start sending pkt */
|
||
} else {
|
||
writeb ((char) (TCR_QMODE | TCR_PAD | TCR_IFC), buf); /* ctrl byte */
|
||
buf += 1;
|
||
writeb ((char) (skb->len & 0xff), buf); /* length (16 bit xfer) */
|
||
buf += 1;
|
||
if (lp->txc) {
|
||
writeb(((skb->len >> 8) & 0xff) | XCT, buf);
|
||
buf += 1;
|
||
writeb (0x04, buf); /* index byte */
|
||
buf += 1;
|
||
writeb (0x00, (buf + skb->len)); /* Write the XCT flag */
|
||
memcpy_toio (buf, skb->data, PRELOAD); /* Write PRELOAD bytes */
|
||
outb (page, EWRK3_TQ); /* Start sending pkt */
|
||
memcpy_toio (buf + PRELOAD,
|
||
skb->data + PRELOAD,
|
||
skb->len - PRELOAD);
|
||
writeb (0xff, (buf + skb->len)); /* Write the XCT flag */
|
||
} else {
|
||
writeb ((skb->len >> 8) & 0xff, buf);
|
||
buf += 1;
|
||
writeb (0x04, buf); /* index byte */
|
||
buf += 1;
|
||
memcpy_toio (buf, skb->data, skb->len); /* Write data bytes */
|
||
outb (page, EWRK3_TQ); /* Start sending pkt */
|
||
}
|
||
}
|
||
|
||
ENABLE_IRQs;
|
||
spin_unlock_irq (&lp->hw_lock);
|
||
|
||
lp->stats.tx_bytes += skb->len;
|
||
dev->trans_start = jiffies;
|
||
dev_kfree_skb (skb);
|
||
|
||
/* Check for free resources: stop Tx queue if there are none */
|
||
if (inb (EWRK3_FMQC) == 0)
|
||
netif_stop_queue (dev);
|
||
|
||
return 0;
|
||
|
||
err_out:
|
||
ENABLE_IRQs;
|
||
spin_unlock_irq (&lp->hw_lock);
|
||
return 1;
|
||
}
|
||
|
||
/*
|
||
** The EWRK3 interrupt handler.
|
||
*/
|
||
static irqreturn_t ewrk3_interrupt(int irq, void *dev_id, struct pt_regs *regs)
|
||
{
|
||
struct net_device *dev = dev_id;
|
||
struct ewrk3_private *lp;
|
||
u_long iobase;
|
||
u_char icr, cr, csr;
|
||
|
||
lp = netdev_priv(dev);
|
||
iobase = dev->base_addr;
|
||
|
||
/* get the interrupt information */
|
||
csr = inb(EWRK3_CSR);
|
||
|
||
/*
|
||
** Mask the EWRK3 board interrupts and turn on the LED
|
||
*/
|
||
spin_lock(&lp->hw_lock);
|
||
DISABLE_IRQs;
|
||
|
||
cr = inb(EWRK3_CR);
|
||
cr |= lp->led_mask;
|
||
outb(cr, EWRK3_CR);
|
||
|
||
if (csr & CSR_RNE) /* Rx interrupt (packet[s] arrived) */
|
||
ewrk3_rx(dev);
|
||
|
||
if (csr & CSR_TNE) /* Tx interrupt (packet sent) */
|
||
ewrk3_tx(dev);
|
||
|
||
/*
|
||
** Now deal with the TX/RX disable flags. These are set when there
|
||
** are no more resources. If resources free up then enable these
|
||
** interrupts, otherwise mask them - failure to do this will result
|
||
** in the system hanging in an interrupt loop.
|
||
*/
|
||
if (inb(EWRK3_FMQC)) { /* any resources available? */
|
||
lp->irq_mask |= ICR_TXDM | ICR_RXDM; /* enable the interrupt source */
|
||
csr &= ~(CSR_TXD | CSR_RXD); /* ensure restart of a stalled TX or RX */
|
||
outb(csr, EWRK3_CSR);
|
||
netif_wake_queue(dev);
|
||
} else {
|
||
lp->irq_mask &= ~(ICR_TXDM | ICR_RXDM); /* disable the interrupt source */
|
||
}
|
||
|
||
/* Unmask the EWRK3 board interrupts and turn off the LED */
|
||
cr &= ~(lp->led_mask);
|
||
outb(cr, EWRK3_CR);
|
||
ENABLE_IRQs;
|
||
spin_unlock(&lp->hw_lock);
|
||
return IRQ_HANDLED;
|
||
}
|
||
|
||
/* Called with lp->hw_lock held */
|
||
static int ewrk3_rx(struct net_device *dev)
|
||
{
|
||
struct ewrk3_private *lp = netdev_priv(dev);
|
||
u_long iobase = dev->base_addr;
|
||
int i, status = 0;
|
||
u_char page;
|
||
void __iomem *buf = NULL;
|
||
|
||
while (inb(EWRK3_RQC) && !status) { /* Whilst there's incoming data */
|
||
if ((page = inb(EWRK3_RQ)) < lp->mPage) { /* Get next entry's buffer page */
|
||
/*
|
||
** Set up shared memory window and pointer into the window
|
||
*/
|
||
if (lp->shmem_length == IO_ONLY) {
|
||
outb(page, EWRK3_IOPR);
|
||
} else if (lp->shmem_length == SHMEM_2K) {
|
||
buf = lp->shmem;
|
||
outb(page, EWRK3_MPR);
|
||
} else if (lp->shmem_length == SHMEM_32K) {
|
||
buf = (((short) page << 11) & 0x7800) + lp->shmem;
|
||
outb((page >> 4), EWRK3_MPR);
|
||
} else if (lp->shmem_length == SHMEM_64K) {
|
||
buf = (((short) page << 11) & 0xf800) + lp->shmem;
|
||
outb((page >> 5), EWRK3_MPR);
|
||
} else {
|
||
status = -1;
|
||
printk("%s: Oops - your private data area is hosed!\n", dev->name);
|
||
}
|
||
|
||
if (!status) {
|
||
char rx_status;
|
||
int pkt_len;
|
||
|
||
if (lp->shmem_length == IO_ONLY) {
|
||
rx_status = inb(EWRK3_DATA);
|
||
pkt_len = inb(EWRK3_DATA);
|
||
pkt_len |= ((u_short) inb(EWRK3_DATA) << 8);
|
||
} else {
|
||
rx_status = readb(buf);
|
||
buf += 1;
|
||
pkt_len = readw(buf);
|
||
buf += 3;
|
||
}
|
||
|
||
if (!(rx_status & R_ROK)) { /* There was an error. */
|
||
lp->stats.rx_errors++; /* Update the error stats. */
|
||
if (rx_status & R_DBE)
|
||
lp->stats.rx_frame_errors++;
|
||
if (rx_status & R_CRC)
|
||
lp->stats.rx_crc_errors++;
|
||
if (rx_status & R_PLL)
|
||
lp->stats.rx_fifo_errors++;
|
||
} else {
|
||
struct sk_buff *skb;
|
||
|
||
if ((skb = dev_alloc_skb(pkt_len + 2)) != NULL) {
|
||
unsigned char *p;
|
||
skb->dev = dev;
|
||
skb_reserve(skb, 2); /* Align to 16 bytes */
|
||
p = skb_put(skb, pkt_len);
|
||
|
||
if (lp->shmem_length == IO_ONLY) {
|
||
*p = inb(EWRK3_DATA); /* dummy read */
|
||
for (i = 0; i < pkt_len; i++) {
|
||
*p++ = inb(EWRK3_DATA);
|
||
}
|
||
} else {
|
||
memcpy_fromio(p, buf, pkt_len);
|
||
}
|
||
|
||
for (i = 1; i < EWRK3_PKT_STAT_SZ - 1; i++) {
|
||
if (pkt_len < i * EWRK3_PKT_BIN_SZ) {
|
||
lp->pktStats.bins[i]++;
|
||
i = EWRK3_PKT_STAT_SZ;
|
||
}
|
||
}
|
||
p = skb->data; /* Look at the dest addr */
|
||
if (p[0] & 0x01) { /* Multicast/Broadcast */
|
||
if ((*(s16 *) & p[0] == -1) && (*(s16 *) & p[2] == -1) && (*(s16 *) & p[4] == -1)) {
|
||
lp->pktStats.broadcast++;
|
||
} else {
|
||
lp->pktStats.multicast++;
|
||
}
|
||
} else if ((*(s16 *) & p[0] == *(s16 *) & dev->dev_addr[0]) &&
|
||
(*(s16 *) & p[2] == *(s16 *) & dev->dev_addr[2]) &&
|
||
(*(s16 *) & p[4] == *(s16 *) & dev->dev_addr[4])) {
|
||
lp->pktStats.unicast++;
|
||
}
|
||
lp->pktStats.bins[0]++; /* Duplicates stats.rx_packets */
|
||
if (lp->pktStats.bins[0] == 0) { /* Reset counters */
|
||
memset(&lp->pktStats, 0, sizeof(lp->pktStats));
|
||
}
|
||
/*
|
||
** Notify the upper protocol layers that there is another
|
||
** packet to handle
|
||
*/
|
||
skb->protocol = eth_type_trans(skb, dev);
|
||
netif_rx(skb);
|
||
|
||
/*
|
||
** Update stats
|
||
*/
|
||
dev->last_rx = jiffies;
|
||
lp->stats.rx_packets++;
|
||
lp->stats.rx_bytes += pkt_len;
|
||
} else {
|
||
printk("%s: Insufficient memory; nuking packet.\n", dev->name);
|
||
lp->stats.rx_dropped++; /* Really, deferred. */
|
||
break;
|
||
}
|
||
}
|
||
}
|
||
/*
|
||
** Return the received buffer to the free memory queue
|
||
*/
|
||
outb(page, EWRK3_FMQ);
|
||
} else {
|
||
printk("ewrk3_rx(): Illegal page number, page %d\n", page);
|
||
printk("ewrk3_rx(): CSR: %02x ICR: %02x FMQC: %02x\n", inb(EWRK3_CSR), inb(EWRK3_ICR), inb(EWRK3_FMQC));
|
||
}
|
||
}
|
||
return status;
|
||
}
|
||
|
||
/*
|
||
** Buffer sent - check for TX buffer errors.
|
||
** Called with lp->hw_lock held
|
||
*/
|
||
static int ewrk3_tx(struct net_device *dev)
|
||
{
|
||
struct ewrk3_private *lp = netdev_priv(dev);
|
||
u_long iobase = dev->base_addr;
|
||
u_char tx_status;
|
||
|
||
while ((tx_status = inb(EWRK3_TDQ)) > 0) { /* Whilst there's old buffers */
|
||
if (tx_status & T_VSTS) { /* The status is valid */
|
||
if (tx_status & T_TXE) {
|
||
lp->stats.tx_errors++;
|
||
if (tx_status & T_NCL)
|
||
lp->stats.tx_carrier_errors++;
|
||
if (tx_status & T_LCL)
|
||
lp->stats.tx_window_errors++;
|
||
if (tx_status & T_CTU) {
|
||
if ((tx_status & T_COLL) ^ T_XUR) {
|
||
lp->pktStats.tx_underruns++;
|
||
} else {
|
||
lp->pktStats.excessive_underruns++;
|
||
}
|
||
} else if (tx_status & T_COLL) {
|
||
if ((tx_status & T_COLL) ^ T_XCOLL) {
|
||
lp->stats.collisions++;
|
||
} else {
|
||
lp->pktStats.excessive_collisions++;
|
||
}
|
||
}
|
||
} else {
|
||
lp->stats.tx_packets++;
|
||
}
|
||
}
|
||
}
|
||
|
||
return 0;
|
||
}
|
||
|
||
static int ewrk3_close(struct net_device *dev)
|
||
{
|
||
struct ewrk3_private *lp = netdev_priv(dev);
|
||
u_long iobase = dev->base_addr;
|
||
u_char icr, csr;
|
||
|
||
netif_stop_queue(dev);
|
||
|
||
if (ewrk3_debug > 1) {
|
||
printk("%s: Shutting down ethercard, status was %2.2x.\n",
|
||
dev->name, inb(EWRK3_CSR));
|
||
}
|
||
/*
|
||
** We stop the EWRK3 here... mask interrupts and stop TX & RX
|
||
*/
|
||
DISABLE_IRQs;
|
||
|
||
STOP_EWRK3;
|
||
|
||
/*
|
||
** Clean out the TX and RX queues here (note that one entry
|
||
** may get added to either the TXD or RX queues if the TX or RX
|
||
** just starts processing a packet before the STOP_EWRK3 command
|
||
** is received. This will be flushed in the ewrk3_open() call).
|
||
*/
|
||
while (inb(EWRK3_TQ));
|
||
while (inb(EWRK3_TDQ));
|
||
while (inb(EWRK3_RQ));
|
||
|
||
if (!lp->hard_strapped) {
|
||
free_irq(dev->irq, dev);
|
||
}
|
||
return 0;
|
||
}
|
||
|
||
static struct net_device_stats *ewrk3_get_stats(struct net_device *dev)
|
||
{
|
||
struct ewrk3_private *lp = netdev_priv(dev);
|
||
|
||
/* Null body since there is no framing error counter */
|
||
return &lp->stats;
|
||
}
|
||
|
||
/*
|
||
** Set or clear the multicast filter for this adapter.
|
||
*/
|
||
static void set_multicast_list(struct net_device *dev)
|
||
{
|
||
struct ewrk3_private *lp = netdev_priv(dev);
|
||
u_long iobase = dev->base_addr;
|
||
u_char csr;
|
||
|
||
csr = inb(EWRK3_CSR);
|
||
|
||
if (lp->shmem_length == IO_ONLY) {
|
||
lp->mctbl = NULL;
|
||
} else {
|
||
lp->mctbl = lp->shmem + PAGE0_HTE;
|
||
}
|
||
|
||
csr &= ~(CSR_PME | CSR_MCE);
|
||
if (dev->flags & IFF_PROMISC) { /* set promiscuous mode */
|
||
csr |= CSR_PME;
|
||
outb(csr, EWRK3_CSR);
|
||
} else {
|
||
SetMulticastFilter(dev);
|
||
csr |= CSR_MCE;
|
||
outb(csr, EWRK3_CSR);
|
||
}
|
||
}
|
||
|
||
/*
|
||
** Calculate the hash code and update the logical address filter
|
||
** from a list of ethernet multicast addresses.
|
||
** Little endian crc one liner from Matt Thomas, DEC.
|
||
**
|
||
** Note that when clearing the table, the broadcast bit must remain asserted
|
||
** to receive broadcast messages.
|
||
*/
|
||
static void SetMulticastFilter(struct net_device *dev)
|
||
{
|
||
struct ewrk3_private *lp = netdev_priv(dev);
|
||
struct dev_mc_list *dmi = dev->mc_list;
|
||
u_long iobase = dev->base_addr;
|
||
int i;
|
||
char *addrs, bit, byte;
|
||
short __iomem *p = lp->mctbl;
|
||
u16 hashcode;
|
||
u32 crc;
|
||
|
||
spin_lock_irq(&lp->hw_lock);
|
||
|
||
if (lp->shmem_length == IO_ONLY) {
|
||
outb(0, EWRK3_IOPR);
|
||
outw(PAGE0_HTE, EWRK3_PIR1);
|
||
} else {
|
||
outb(0, EWRK3_MPR);
|
||
}
|
||
|
||
if (dev->flags & IFF_ALLMULTI) {
|
||
for (i = 0; i < (HASH_TABLE_LEN >> 3); i++) {
|
||
if (lp->shmem_length == IO_ONLY) {
|
||
outb(0xff, EWRK3_DATA);
|
||
} else { /* memset didn't work here */
|
||
writew(0xffff, p);
|
||
p++;
|
||
i++;
|
||
}
|
||
}
|
||
} else {
|
||
/* Clear table except for broadcast bit */
|
||
if (lp->shmem_length == IO_ONLY) {
|
||
for (i = 0; i < (HASH_TABLE_LEN >> 4) - 1; i++) {
|
||
outb(0x00, EWRK3_DATA);
|
||
}
|
||
outb(0x80, EWRK3_DATA);
|
||
i++; /* insert the broadcast bit */
|
||
for (; i < (HASH_TABLE_LEN >> 3); i++) {
|
||
outb(0x00, EWRK3_DATA);
|
||
}
|
||
} else {
|
||
memset_io(lp->mctbl, 0, HASH_TABLE_LEN >> 3);
|
||
writeb(0x80, lp->mctbl + (HASH_TABLE_LEN >> 4) - 1);
|
||
}
|
||
|
||
/* Update table */
|
||
for (i = 0; i < dev->mc_count; i++) { /* for each address in the list */
|
||
addrs = dmi->dmi_addr;
|
||
dmi = dmi->next;
|
||
if ((*addrs & 0x01) == 1) { /* multicast address? */
|
||
crc = ether_crc_le(ETH_ALEN, addrs);
|
||
hashcode = crc & ((1 << 9) - 1); /* hashcode is 9 LSb of CRC */
|
||
|
||
byte = hashcode >> 3; /* bit[3-8] -> byte in filter */
|
||
bit = 1 << (hashcode & 0x07); /* bit[0-2] -> bit in byte */
|
||
|
||
if (lp->shmem_length == IO_ONLY) {
|
||
u_char tmp;
|
||
|
||
outw(PAGE0_HTE + byte, EWRK3_PIR1);
|
||
tmp = inb(EWRK3_DATA);
|
||
tmp |= bit;
|
||
outw(PAGE0_HTE + byte, EWRK3_PIR1);
|
||
outb(tmp, EWRK3_DATA);
|
||
} else {
|
||
writeb(readb(lp->mctbl + byte) | bit, lp->mctbl + byte);
|
||
}
|
||
}
|
||
}
|
||
}
|
||
|
||
spin_unlock_irq(&lp->hw_lock);
|
||
}
|
||
|
||
/*
|
||
** ISA bus I/O device probe
|
||
*/
|
||
static int __init isa_probe(struct net_device *dev, u_long ioaddr)
|
||
{
|
||
int i = num_ewrks3s, maxSlots;
|
||
int ret = -ENODEV;
|
||
|
||
u_long iobase;
|
||
|
||
if (ioaddr >= 0x400)
|
||
goto out;
|
||
|
||
if (ioaddr == 0) { /* Autoprobing */
|
||
iobase = EWRK3_IO_BASE; /* Get the first slot address */
|
||
maxSlots = 24;
|
||
} else { /* Probe a specific location */
|
||
iobase = ioaddr;
|
||
maxSlots = i + 1;
|
||
}
|
||
|
||
for (; (i < maxSlots) && (dev != NULL);
|
||
iobase += EWRK3_IOP_INC, i++)
|
||
{
|
||
if (request_region(iobase, EWRK3_TOTAL_SIZE, DRV_NAME)) {
|
||
if (DevicePresent(iobase) == 0) {
|
||
int irq = dev->irq;
|
||
ret = ewrk3_hw_init(dev, iobase);
|
||
if (!ret)
|
||
break;
|
||
dev->irq = irq;
|
||
}
|
||
release_region(iobase, EWRK3_TOTAL_SIZE);
|
||
}
|
||
}
|
||
out:
|
||
|
||
return ret;
|
||
}
|
||
|
||
/*
|
||
** EISA bus I/O device probe. Probe from slot 1 since slot 0 is usually
|
||
** the motherboard.
|
||
*/
|
||
static int __init eisa_probe(struct net_device *dev, u_long ioaddr)
|
||
{
|
||
int i, maxSlots;
|
||
u_long iobase;
|
||
int ret = -ENODEV;
|
||
|
||
if (ioaddr < 0x1000)
|
||
goto out;
|
||
|
||
iobase = ioaddr;
|
||
i = (ioaddr >> 12);
|
||
maxSlots = i + 1;
|
||
|
||
for (i = 1; (i < maxSlots) && (dev != NULL); i++, iobase += EISA_SLOT_INC) {
|
||
if (EISA_signature(name, EISA_ID) == 0) {
|
||
if (request_region(iobase, EWRK3_TOTAL_SIZE, DRV_NAME) &&
|
||
DevicePresent(iobase) == 0) {
|
||
int irq = dev->irq;
|
||
ret = ewrk3_hw_init(dev, iobase);
|
||
if (!ret)
|
||
break;
|
||
dev->irq = irq;
|
||
}
|
||
release_region(iobase, EWRK3_TOTAL_SIZE);
|
||
}
|
||
}
|
||
|
||
out:
|
||
return ret;
|
||
}
|
||
|
||
|
||
/*
|
||
** Read the EWRK3 EEPROM using this routine
|
||
*/
|
||
static int Read_EEPROM(u_long iobase, u_char eaddr)
|
||
{
|
||
int i;
|
||
|
||
outb((eaddr & 0x3f), EWRK3_PIR1); /* set up 6 bits of address info */
|
||
outb(EEPROM_RD, EWRK3_IOPR); /* issue read command */
|
||
for (i = 0; i < 5000; i++)
|
||
inb(EWRK3_CSR); /* wait 1msec */
|
||
|
||
return inw(EWRK3_EPROM1); /* 16 bits data return */
|
||
}
|
||
|
||
/*
|
||
** Write the EWRK3 EEPROM using this routine
|
||
*/
|
||
static int Write_EEPROM(short data, u_long iobase, u_char eaddr)
|
||
{
|
||
int i;
|
||
|
||
outb(EEPROM_WR_EN, EWRK3_IOPR); /* issue write enable command */
|
||
for (i = 0; i < 5000; i++)
|
||
inb(EWRK3_CSR); /* wait 1msec */
|
||
outw(data, EWRK3_EPROM1); /* write data to register */
|
||
outb((eaddr & 0x3f), EWRK3_PIR1); /* set up 6 bits of address info */
|
||
outb(EEPROM_WR, EWRK3_IOPR); /* issue write command */
|
||
for (i = 0; i < 75000; i++)
|
||
inb(EWRK3_CSR); /* wait 15msec */
|
||
outb(EEPROM_WR_DIS, EWRK3_IOPR); /* issue write disable command */
|
||
for (i = 0; i < 5000; i++)
|
||
inb(EWRK3_CSR); /* wait 1msec */
|
||
|
||
return 0;
|
||
}
|
||
|
||
/*
|
||
** Look for a particular board name in the on-board EEPROM.
|
||
*/
|
||
static void __init EthwrkSignature(char *name, char *eeprom_image)
|
||
{
|
||
int i;
|
||
char *signatures[] = EWRK3_SIGNATURE;
|
||
|
||
for (i=0; *signatures[i] != '\0'; i++)
|
||
if( !strncmp(eeprom_image+EEPROM_PNAME7, signatures[i], strlen(signatures[i])) )
|
||
break;
|
||
|
||
if (*signatures[i] != '\0') {
|
||
memcpy(name, eeprom_image+EEPROM_PNAME7, EWRK3_STRLEN);
|
||
name[EWRK3_STRLEN] = '\0';
|
||
} else
|
||
name[0] = '\0';
|
||
|
||
return;
|
||
}
|
||
|
||
/*
|
||
** Look for a special sequence in the Ethernet station address PROM that
|
||
** is common across all EWRK3 products.
|
||
**
|
||
** Search the Ethernet address ROM for the signature. Since the ROM address
|
||
** counter can start at an arbitrary point, the search must include the entire
|
||
** probe sequence length plus the (length_of_the_signature - 1).
|
||
** Stop the search IMMEDIATELY after the signature is found so that the
|
||
** PROM address counter is correctly positioned at the start of the
|
||
** ethernet address for later read out.
|
||
*/
|
||
|
||
static int __init DevicePresent(u_long iobase)
|
||
{
|
||
union {
|
||
struct {
|
||
u32 a;
|
||
u32 b;
|
||
} llsig;
|
||
char Sig[sizeof(u32) << 1];
|
||
}
|
||
dev;
|
||
short sigLength;
|
||
char data;
|
||
int i, j, status = 0;
|
||
|
||
dev.llsig.a = ETH_PROM_SIG;
|
||
dev.llsig.b = ETH_PROM_SIG;
|
||
sigLength = sizeof(u32) << 1;
|
||
|
||
for (i = 0, j = 0; j < sigLength && i < PROBE_LENGTH + sigLength - 1; i++) {
|
||
data = inb(EWRK3_APROM);
|
||
if (dev.Sig[j] == data) { /* track signature */
|
||
j++;
|
||
} else { /* lost signature; begin search again */
|
||
if (data == dev.Sig[0]) {
|
||
j = 1;
|
||
} else {
|
||
j = 0;
|
||
}
|
||
}
|
||
}
|
||
|
||
if (j != sigLength) {
|
||
status = -ENODEV; /* search failed */
|
||
}
|
||
return status;
|
||
}
|
||
|
||
static u_char __init get_hw_addr(struct net_device *dev, u_char * eeprom_image, char chipType)
|
||
{
|
||
int i, j, k;
|
||
u_short chksum;
|
||
u_char crc, lfsr, sd, status = 0;
|
||
u_long iobase = dev->base_addr;
|
||
u16 tmp;
|
||
|
||
if (chipType == LeMAC2) {
|
||
for (crc = 0x6a, j = 0; j < ETH_ALEN; j++) {
|
||
sd = dev->dev_addr[j] = eeprom_image[EEPROM_PADDR0 + j];
|
||
outb(dev->dev_addr[j], EWRK3_PAR0 + j);
|
||
for (k = 0; k < 8; k++, sd >>= 1) {
|
||
lfsr = ((((crc & 0x02) >> 1) ^ (crc & 0x01)) ^ (sd & 0x01)) << 7;
|
||
crc = (crc >> 1) + lfsr;
|
||
}
|
||
}
|
||
if (crc != eeprom_image[EEPROM_PA_CRC])
|
||
status = -1;
|
||
} else {
|
||
for (i = 0, k = 0; i < ETH_ALEN;) {
|
||
k <<= 1;
|
||
if (k > 0xffff)
|
||
k -= 0xffff;
|
||
|
||
k += (u_char) (tmp = inb(EWRK3_APROM));
|
||
dev->dev_addr[i] = (u_char) tmp;
|
||
outb(dev->dev_addr[i], EWRK3_PAR0 + i);
|
||
i++;
|
||
k += (u_short) ((tmp = inb(EWRK3_APROM)) << 8);
|
||
dev->dev_addr[i] = (u_char) tmp;
|
||
outb(dev->dev_addr[i], EWRK3_PAR0 + i);
|
||
i++;
|
||
|
||
if (k > 0xffff)
|
||
k -= 0xffff;
|
||
}
|
||
if (k == 0xffff)
|
||
k = 0;
|
||
chksum = inb(EWRK3_APROM);
|
||
chksum |= (inb(EWRK3_APROM) << 8);
|
||
if (k != chksum)
|
||
status = -1;
|
||
}
|
||
|
||
return status;
|
||
}
|
||
|
||
/*
|
||
** Look for a particular board name in the EISA configuration space
|
||
*/
|
||
static int __init EISA_signature(char *name, s32 eisa_id)
|
||
{
|
||
u_long i;
|
||
char *signatures[] = EWRK3_SIGNATURE;
|
||
char ManCode[EWRK3_STRLEN];
|
||
union {
|
||
s32 ID;
|
||
char Id[4];
|
||
} Eisa;
|
||
int status = 0;
|
||
|
||
*name = '\0';
|
||
for (i = 0; i < 4; i++) {
|
||
Eisa.Id[i] = inb(eisa_id + i);
|
||
}
|
||
|
||
ManCode[0] = (((Eisa.Id[0] >> 2) & 0x1f) + 0x40);
|
||
ManCode[1] = (((Eisa.Id[1] & 0xe0) >> 5) + ((Eisa.Id[0] & 0x03) << 3) + 0x40);
|
||
ManCode[2] = (((Eisa.Id[2] >> 4) & 0x0f) + 0x30);
|
||
ManCode[3] = ((Eisa.Id[2] & 0x0f) + 0x30);
|
||
ManCode[4] = (((Eisa.Id[3] >> 4) & 0x0f) + 0x30);
|
||
ManCode[5] = '\0';
|
||
|
||
for (i = 0; (*signatures[i] != '\0') && (*name == '\0'); i++) {
|
||
if (strstr(ManCode, signatures[i]) != NULL) {
|
||
strcpy(name, ManCode);
|
||
status = 1;
|
||
}
|
||
}
|
||
|
||
return status; /* return the device name string */
|
||
}
|
||
|
||
static void ewrk3_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info)
|
||
{
|
||
int fwrev = Read_EEPROM(dev->base_addr, EEPROM_REVLVL);
|
||
|
||
strcpy(info->driver, DRV_NAME);
|
||
strcpy(info->version, DRV_VERSION);
|
||
sprintf(info->fw_version, "%d", fwrev);
|
||
strcpy(info->bus_info, "N/A");
|
||
info->eedump_len = EEPROM_MAX;
|
||
}
|
||
|
||
static int ewrk3_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
|
||
{
|
||
struct ewrk3_private *lp = netdev_priv(dev);
|
||
unsigned long iobase = dev->base_addr;
|
||
u8 cr = inb(EWRK3_CR);
|
||
|
||
switch (lp->adapter_name[4]) {
|
||
case '3': /* DE203 */
|
||
ecmd->supported = SUPPORTED_BNC;
|
||
ecmd->port = PORT_BNC;
|
||
break;
|
||
|
||
case '4': /* DE204 */
|
||
ecmd->supported = SUPPORTED_TP;
|
||
ecmd->port = PORT_TP;
|
||
break;
|
||
|
||
case '5': /* DE205 */
|
||
ecmd->supported = SUPPORTED_TP | SUPPORTED_BNC | SUPPORTED_AUI;
|
||
ecmd->autoneg = !(cr & CR_APD);
|
||
/*
|
||
** Port is only valid if autoneg is disabled
|
||
** and even then we don't know if AUI is jumpered.
|
||
*/
|
||
if (!ecmd->autoneg)
|
||
ecmd->port = (cr & CR_PSEL) ? PORT_BNC : PORT_TP;
|
||
break;
|
||
}
|
||
|
||
ecmd->supported |= SUPPORTED_10baseT_Half;
|
||
ecmd->speed = SPEED_10;
|
||
ecmd->duplex = DUPLEX_HALF;
|
||
return 0;
|
||
}
|
||
|
||
static int ewrk3_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
|
||
{
|
||
struct ewrk3_private *lp = netdev_priv(dev);
|
||
unsigned long iobase = dev->base_addr;
|
||
unsigned long flags;
|
||
u8 cr;
|
||
|
||
/* DE205 is the only card with anything to set */
|
||
if (lp->adapter_name[4] != '5')
|
||
return -EOPNOTSUPP;
|
||
|
||
/* Sanity-check parameters */
|
||
if (ecmd->speed != SPEED_10)
|
||
return -EINVAL;
|
||
if (ecmd->port != PORT_TP && ecmd->port != PORT_BNC)
|
||
return -EINVAL; /* AUI is not software-selectable */
|
||
if (ecmd->transceiver != XCVR_INTERNAL)
|
||
return -EINVAL;
|
||
if (ecmd->duplex != DUPLEX_HALF)
|
||
return -EINVAL;
|
||
if (ecmd->phy_address != 0)
|
||
return -EINVAL;
|
||
|
||
spin_lock_irqsave(&lp->hw_lock, flags);
|
||
cr = inb(EWRK3_CR);
|
||
|
||
/* If Autoneg is set, change to Auto Port mode */
|
||
/* Otherwise, disable Auto Port and set port explicitly */
|
||
if (ecmd->autoneg) {
|
||
cr &= ~CR_APD;
|
||
} else {
|
||
cr |= CR_APD;
|
||
if (ecmd->port == PORT_TP)
|
||
cr &= ~CR_PSEL; /* Force TP */
|
||
else
|
||
cr |= CR_PSEL; /* Force BNC */
|
||
}
|
||
|
||
/* Commit the changes */
|
||
outb(cr, EWRK3_CR);
|
||
spin_unlock_irqrestore(&lp->hw_lock, flags);
|
||
return 0;
|
||
}
|
||
|
||
static u32 ewrk3_get_link(struct net_device *dev)
|
||
{
|
||
unsigned long iobase = dev->base_addr;
|
||
u8 cmr = inb(EWRK3_CMR);
|
||
/* DE203 has BNC only and link status does not apply */
|
||
/* On DE204 this is always valid since TP is the only port. */
|
||
/* On DE205 this reflects TP status even if BNC or AUI is selected. */
|
||
return !(cmr & CMR_LINK);
|
||
}
|
||
|
||
static int ewrk3_phys_id(struct net_device *dev, u32 data)
|
||
{
|
||
struct ewrk3_private *lp = netdev_priv(dev);
|
||
unsigned long iobase = dev->base_addr;
|
||
unsigned long flags;
|
||
u8 cr;
|
||
int count;
|
||
|
||
/* Toggle LED 4x per second */
|
||
count = data << 2;
|
||
|
||
spin_lock_irqsave(&lp->hw_lock, flags);
|
||
|
||
/* Bail if a PHYS_ID is already in progress */
|
||
if (lp->led_mask == 0) {
|
||
spin_unlock_irqrestore(&lp->hw_lock, flags);
|
||
return -EBUSY;
|
||
}
|
||
|
||
/* Prevent ISR from twiddling the LED */
|
||
lp->led_mask = 0;
|
||
|
||
while (count--) {
|
||
/* Toggle the LED */
|
||
cr = inb(EWRK3_CR);
|
||
outb(cr ^ CR_LED, EWRK3_CR);
|
||
|
||
/* Wait a little while */
|
||
spin_unlock_irqrestore(&lp->hw_lock, flags);
|
||
msleep(250);
|
||
spin_lock_irqsave(&lp->hw_lock, flags);
|
||
|
||
/* Exit if we got a signal */
|
||
if (signal_pending(current))
|
||
break;
|
||
}
|
||
|
||
lp->led_mask = CR_LED;
|
||
cr = inb(EWRK3_CR);
|
||
outb(cr & ~CR_LED, EWRK3_CR);
|
||
spin_unlock_irqrestore(&lp->hw_lock, flags);
|
||
return signal_pending(current) ? -ERESTARTSYS : 0;
|
||
}
|
||
|
||
static struct ethtool_ops ethtool_ops_203 = {
|
||
.get_drvinfo = ewrk3_get_drvinfo,
|
||
.get_settings = ewrk3_get_settings,
|
||
.set_settings = ewrk3_set_settings,
|
||
.phys_id = ewrk3_phys_id,
|
||
};
|
||
|
||
static struct ethtool_ops ethtool_ops = {
|
||
.get_drvinfo = ewrk3_get_drvinfo,
|
||
.get_settings = ewrk3_get_settings,
|
||
.set_settings = ewrk3_set_settings,
|
||
.get_link = ewrk3_get_link,
|
||
.phys_id = ewrk3_phys_id,
|
||
};
|
||
|
||
/*
|
||
** Perform IOCTL call functions here. Some are privileged operations and the
|
||
** effective uid is checked in those cases.
|
||
*/
|
||
static int ewrk3_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
|
||
{
|
||
struct ewrk3_private *lp = netdev_priv(dev);
|
||
struct ewrk3_ioctl *ioc = (struct ewrk3_ioctl *) &rq->ifr_ifru;
|
||
u_long iobase = dev->base_addr;
|
||
int i, j, status = 0;
|
||
u_char csr;
|
||
unsigned long flags;
|
||
union ewrk3_addr {
|
||
u_char addr[HASH_TABLE_LEN * ETH_ALEN];
|
||
u_short val[(HASH_TABLE_LEN * ETH_ALEN) >> 1];
|
||
};
|
||
|
||
union ewrk3_addr *tmp;
|
||
|
||
/* All we handle are private IOCTLs */
|
||
if (cmd != EWRK3IOCTL)
|
||
return -EOPNOTSUPP;
|
||
|
||
tmp = kmalloc(sizeof(union ewrk3_addr), GFP_KERNEL);
|
||
if(tmp==NULL)
|
||
return -ENOMEM;
|
||
|
||
switch (ioc->cmd) {
|
||
case EWRK3_GET_HWADDR: /* Get the hardware address */
|
||
for (i = 0; i < ETH_ALEN; i++) {
|
||
tmp->addr[i] = dev->dev_addr[i];
|
||
}
|
||
ioc->len = ETH_ALEN;
|
||
if (copy_to_user(ioc->data, tmp->addr, ioc->len))
|
||
status = -EFAULT;
|
||
break;
|
||
|
||
case EWRK3_SET_HWADDR: /* Set the hardware address */
|
||
if (capable(CAP_NET_ADMIN)) {
|
||
spin_lock_irqsave(&lp->hw_lock, flags);
|
||
csr = inb(EWRK3_CSR);
|
||
csr |= (CSR_TXD | CSR_RXD);
|
||
outb(csr, EWRK3_CSR); /* Disable the TX and RX */
|
||
spin_unlock_irqrestore(&lp->hw_lock, flags);
|
||
|
||
if (copy_from_user(tmp->addr, ioc->data, ETH_ALEN)) {
|
||
status = -EFAULT;
|
||
break;
|
||
}
|
||
spin_lock_irqsave(&lp->hw_lock, flags);
|
||
for (i = 0; i < ETH_ALEN; i++) {
|
||
dev->dev_addr[i] = tmp->addr[i];
|
||
outb(tmp->addr[i], EWRK3_PAR0 + i);
|
||
}
|
||
|
||
csr = inb(EWRK3_CSR);
|
||
csr &= ~(CSR_TXD | CSR_RXD); /* Enable the TX and RX */
|
||
outb(csr, EWRK3_CSR);
|
||
spin_unlock_irqrestore(&lp->hw_lock, flags);
|
||
} else {
|
||
status = -EPERM;
|
||
}
|
||
|
||
break;
|
||
case EWRK3_SET_PROM: /* Set Promiscuous Mode */
|
||
if (capable(CAP_NET_ADMIN)) {
|
||
spin_lock_irqsave(&lp->hw_lock, flags);
|
||
csr = inb(EWRK3_CSR);
|
||
csr |= CSR_PME;
|
||
csr &= ~CSR_MCE;
|
||
outb(csr, EWRK3_CSR);
|
||
spin_unlock_irqrestore(&lp->hw_lock, flags);
|
||
} else {
|
||
status = -EPERM;
|
||
}
|
||
|
||
break;
|
||
case EWRK3_CLR_PROM: /* Clear Promiscuous Mode */
|
||
if (capable(CAP_NET_ADMIN)) {
|
||
spin_lock_irqsave(&lp->hw_lock, flags);
|
||
csr = inb(EWRK3_CSR);
|
||
csr &= ~CSR_PME;
|
||
outb(csr, EWRK3_CSR);
|
||
spin_unlock_irqrestore(&lp->hw_lock, flags);
|
||
} else {
|
||
status = -EPERM;
|
||
}
|
||
|
||
break;
|
||
case EWRK3_GET_MCA: /* Get the multicast address table */
|
||
spin_lock_irqsave(&lp->hw_lock, flags);
|
||
if (lp->shmem_length == IO_ONLY) {
|
||
outb(0, EWRK3_IOPR);
|
||
outw(PAGE0_HTE, EWRK3_PIR1);
|
||
for (i = 0; i < (HASH_TABLE_LEN >> 3); i++) {
|
||
tmp->addr[i] = inb(EWRK3_DATA);
|
||
}
|
||
} else {
|
||
outb(0, EWRK3_MPR);
|
||
memcpy_fromio(tmp->addr, lp->shmem + PAGE0_HTE, (HASH_TABLE_LEN >> 3));
|
||
}
|
||
spin_unlock_irqrestore(&lp->hw_lock, flags);
|
||
|
||
ioc->len = (HASH_TABLE_LEN >> 3);
|
||
if (copy_to_user(ioc->data, tmp->addr, ioc->len))
|
||
status = -EFAULT;
|
||
|
||
break;
|
||
case EWRK3_SET_MCA: /* Set a multicast address */
|
||
if (capable(CAP_NET_ADMIN)) {
|
||
if (ioc->len > 1024)
|
||
{
|
||
status = -EINVAL;
|
||
break;
|
||
}
|
||
if (copy_from_user(tmp->addr, ioc->data, ETH_ALEN * ioc->len)) {
|
||
status = -EFAULT;
|
||
break;
|
||
}
|
||
set_multicast_list(dev);
|
||
} else {
|
||
status = -EPERM;
|
||
}
|
||
|
||
break;
|
||
case EWRK3_CLR_MCA: /* Clear all multicast addresses */
|
||
if (capable(CAP_NET_ADMIN)) {
|
||
set_multicast_list(dev);
|
||
} else {
|
||
status = -EPERM;
|
||
}
|
||
|
||
break;
|
||
case EWRK3_MCA_EN: /* Enable multicast addressing */
|
||
if (capable(CAP_NET_ADMIN)) {
|
||
spin_lock_irqsave(&lp->hw_lock, flags);
|
||
csr = inb(EWRK3_CSR);
|
||
csr |= CSR_MCE;
|
||
csr &= ~CSR_PME;
|
||
outb(csr, EWRK3_CSR);
|
||
spin_unlock_irqrestore(&lp->hw_lock, flags);
|
||
} else {
|
||
status = -EPERM;
|
||
}
|
||
|
||
break;
|
||
case EWRK3_GET_STATS: { /* Get the driver statistics */
|
||
struct ewrk3_stats *tmp_stats =
|
||
kmalloc(sizeof(lp->pktStats), GFP_KERNEL);
|
||
if (!tmp_stats) {
|
||
status = -ENOMEM;
|
||
break;
|
||
}
|
||
|
||
spin_lock_irqsave(&lp->hw_lock, flags);
|
||
memcpy(tmp_stats, &lp->pktStats, sizeof(lp->pktStats));
|
||
spin_unlock_irqrestore(&lp->hw_lock, flags);
|
||
|
||
ioc->len = sizeof(lp->pktStats);
|
||
if (copy_to_user(ioc->data, tmp_stats, sizeof(lp->pktStats)))
|
||
status = -EFAULT;
|
||
kfree(tmp_stats);
|
||
break;
|
||
}
|
||
case EWRK3_CLR_STATS: /* Zero out the driver statistics */
|
||
if (capable(CAP_NET_ADMIN)) {
|
||
spin_lock_irqsave(&lp->hw_lock, flags);
|
||
memset(&lp->pktStats, 0, sizeof(lp->pktStats));
|
||
spin_unlock_irqrestore(&lp->hw_lock,flags);
|
||
} else {
|
||
status = -EPERM;
|
||
}
|
||
|
||
break;
|
||
case EWRK3_GET_CSR: /* Get the CSR Register contents */
|
||
tmp->addr[0] = inb(EWRK3_CSR);
|
||
ioc->len = 1;
|
||
if (copy_to_user(ioc->data, tmp->addr, ioc->len))
|
||
status = -EFAULT;
|
||
break;
|
||
case EWRK3_SET_CSR: /* Set the CSR Register contents */
|
||
if (capable(CAP_NET_ADMIN)) {
|
||
if (copy_from_user(tmp->addr, ioc->data, 1)) {
|
||
status = -EFAULT;
|
||
break;
|
||
}
|
||
outb(tmp->addr[0], EWRK3_CSR);
|
||
} else {
|
||
status = -EPERM;
|
||
}
|
||
|
||
break;
|
||
case EWRK3_GET_EEPROM: /* Get the EEPROM contents */
|
||
if (capable(CAP_NET_ADMIN)) {
|
||
for (i = 0; i < (EEPROM_MAX >> 1); i++) {
|
||
tmp->val[i] = (short) Read_EEPROM(iobase, i);
|
||
}
|
||
i = EEPROM_MAX;
|
||
tmp->addr[i++] = inb(EWRK3_CMR); /* Config/Management Reg. */
|
||
for (j = 0; j < ETH_ALEN; j++) {
|
||
tmp->addr[i++] = inb(EWRK3_PAR0 + j);
|
||
}
|
||
ioc->len = EEPROM_MAX + 1 + ETH_ALEN;
|
||
if (copy_to_user(ioc->data, tmp->addr, ioc->len))
|
||
status = -EFAULT;
|
||
} else {
|
||
status = -EPERM;
|
||
}
|
||
|
||
break;
|
||
case EWRK3_SET_EEPROM: /* Set the EEPROM contents */
|
||
if (capable(CAP_NET_ADMIN)) {
|
||
if (copy_from_user(tmp->addr, ioc->data, EEPROM_MAX)) {
|
||
status = -EFAULT;
|
||
break;
|
||
}
|
||
for (i = 0; i < (EEPROM_MAX >> 1); i++) {
|
||
Write_EEPROM(tmp->val[i], iobase, i);
|
||
}
|
||
} else {
|
||
status = -EPERM;
|
||
}
|
||
|
||
break;
|
||
case EWRK3_GET_CMR: /* Get the CMR Register contents */
|
||
tmp->addr[0] = inb(EWRK3_CMR);
|
||
ioc->len = 1;
|
||
if (copy_to_user(ioc->data, tmp->addr, ioc->len))
|
||
status = -EFAULT;
|
||
break;
|
||
case EWRK3_SET_TX_CUT_THRU: /* Set TX cut through mode */
|
||
if (capable(CAP_NET_ADMIN)) {
|
||
lp->txc = 1;
|
||
} else {
|
||
status = -EPERM;
|
||
}
|
||
|
||
break;
|
||
case EWRK3_CLR_TX_CUT_THRU: /* Clear TX cut through mode */
|
||
if (capable(CAP_NET_ADMIN)) {
|
||
lp->txc = 0;
|
||
} else {
|
||
status = -EPERM;
|
||
}
|
||
|
||
break;
|
||
default:
|
||
status = -EOPNOTSUPP;
|
||
}
|
||
kfree(tmp);
|
||
return status;
|
||
}
|
||
|
||
#ifdef MODULE
|
||
static struct net_device *ewrk3_devs[MAX_NUM_EWRK3S];
|
||
static int ndevs;
|
||
static int io[MAX_NUM_EWRK3S+1] = { 0x300, 0, };
|
||
|
||
/* '21' below should really be 'MAX_NUM_EWRK3S' */
|
||
module_param_array(io, int, NULL, 0);
|
||
module_param_array(irq, int, NULL, 0);
|
||
MODULE_PARM_DESC(io, "EtherWORKS 3 I/O base address(es)");
|
||
MODULE_PARM_DESC(irq, "EtherWORKS 3 IRQ number(s)");
|
||
|
||
static __exit void ewrk3_exit_module(void)
|
||
{
|
||
int i;
|
||
|
||
for( i=0; i<ndevs; i++ ) {
|
||
struct net_device *dev = ewrk3_devs[i];
|
||
struct ewrk3_private *lp = netdev_priv(dev);
|
||
ewrk3_devs[i] = NULL;
|
||
unregister_netdev(dev);
|
||
release_region(dev->base_addr, EWRK3_TOTAL_SIZE);
|
||
iounmap(lp->shmem);
|
||
free_netdev(dev);
|
||
}
|
||
}
|
||
|
||
static __init int ewrk3_init_module(void)
|
||
{
|
||
int i=0;
|
||
|
||
while( io[i] && irq[i] ) {
|
||
struct net_device *dev
|
||
= alloc_etherdev(sizeof(struct ewrk3_private));
|
||
|
||
if (!dev)
|
||
break;
|
||
|
||
if (ewrk3_probe1(dev, io[i], irq[i]) != 0) {
|
||
free_netdev(dev);
|
||
break;
|
||
}
|
||
|
||
ewrk3_devs[ndevs++] = dev;
|
||
i++;
|
||
}
|
||
|
||
return ndevs ? 0 : -EIO;
|
||
}
|
||
|
||
|
||
/* Hack for breakage in new module stuff */
|
||
module_exit(ewrk3_exit_module);
|
||
module_init(ewrk3_init_module);
|
||
#endif /* MODULE */
|
||
MODULE_LICENSE("GPL");
|
||
|
||
|
||
|
||
/*
|
||
* Local variables:
|
||
* compile-command: "gcc -D__KERNEL__ -I/linux/include -Wall -Wstrict-prototypes -fomit-frame-pointer -fno-strength-reduce -malign-loops=2 -malign-jumps=2 -malign-functions=2 -O2 -m486 -c ewrk3.c"
|
||
*
|
||
* compile-command: "gcc -D__KERNEL__ -DMODULE -I/linux/include -Wall -Wstrict-prototypes -fomit-frame-pointer -fno-strength-reduce -malign-loops=2 -malign-jumps=2 -malign-functions=2 -O2 -m486 -c ewrk3.c"
|
||
* End:
|
||
*/
|