linux/drivers/iio
Greg Kroah-Hartman 821f7ce79f First set of new device support, features and cleanups for IIO in the 5.6 cycle
New device support
 
 * ad7091r5 ADC
   - New driver with follow up patch adding scale and vref support.
   - DT bindings
 * ad7923
   - Support for ad7908, ad7918 and ad7928 added to driver.
 * bma180
   - Support the BMA254 accelerometer. Required fairly substantial rework
     to allow for small differences between this an existing parts.
 * bma400 accelerometer
   - New driver with follow up patch for regulator support.
   - DT bindings.
 * asc dlhl60d
   - New driver support this range of pressure and temperature sensors.
   - DT bindings.
 * ltc2496 ADC
   - New driver to support this ADC.
   - Split the existing LTC2497 driver generic component out and reuse.
   - DT bindings.
 * parallax ping
   - New driver supporting ultrasonic and laser tof distance sensors.
   - Bindings for these sensors.
 
 New features
 
 * core
   - New char type for read_raw returns, used for thermocouple types.
   - Rename read_first_n callback to read.   The reasons behind the original
     naming are lost to the mists of time.
 * ad799x
   - Allow pm_ops to disable device completely allowing regulator power down.
 * bma180
   - Enable basic regulator support.
 * dmaengine buffer
   - Report platform data alignment requirements via new ABI.
 * max31856
   - Add option to set mains filter rejection frequency and document
     new in_temp_filter_notch_center_frequency ABI.
   - Add support for configuring HW averaging (oversampling ratio)
   - Add runtime configuration of thermocouple type and document new ABI.
 * maxim-thermocouple
   - Add read only access to thermocouple type using new ABI, includes
     adding more specific compatibles to reflect which variant of the
     chip is being used.
 * mpu6050
   - Provide option to support the PMU9150 in package magnetometer directly
     rather than via auxiliary bus.
 * stm32_adc
   - Add overrun interrupt checks to detect if this happens.
 * st_lsm6dsx
   - Enable the sensor-hub support for lsm6dsm. Includes various reworks to
     allow this.
 
 Cleanups and minor fixes
 
 * Subsystem wide
   - Tidy up indentation in Kconfig and fix alphabetical order of AD7091R5.
   - Drop linux/gpio.h and linux/of_gpio.h from drivers that don't use them.
 * ad7266
   - Convert to GPIO descriptors.
 * ad7303
   - Avoid a dance with checking if the regulator is supplied by just
     using the optional request interface.
 * ad7887
   - Simplify channel specification assignment to enable adding more devices.
 * ad7923
   - Drop some unused and largely pointless defines of BOB_N==N variety.
   - Tidy up checkpatch warnings.
   - Add missing of_device_id table.
 * adf4350
   - Convert to GPIO descriptors.
 * ak8975
   - Convert to GPIO descriptors.
 * ADIS library and drivers
   - Expand scope of txrx_lock to cover all state and rename as state_lock
   - Add unlocked read / write to allow grouping of consecutive calls under
     single lock / unlock.
   - Add unlocked check_status, reset to allow grouping under single
     lock / unlock.
   - Remove remaining uses of core mlock for local state protection.
     mlock should never be used directly as it protects tightly defined
     core IIO device management state.
 * adis16240
   - Enforce only supported SPI mode on driver load + add DT binding doc.
 * atlas-ph-sensor
   - Rename to atlas-sensor given it now covers things beyond ph sensors.
 * bma180
   - Use local dev variable to tidy up code.
   - Use c99 style explicity .member assignment to make driver more readable.
 * bmp280
   - Drop ACPI support. No evidence this was used and appropriate ID is not
     registered.
   - Allow ACPI to bind device via PRP0001
 * dmaengine buffer
   - Use dma_request_chan instead of dma_request_slave_channel_reason as that
     ABI is going away.
   - Add module info to avoid tainting the kernel.
 * hts221
   - Avoid magic number defines when only used to fill structure elements
     that are self describing.
 * lm3533
   - Drop a stray semicolon.
 * max9611
   - Cleanup enum handling to be more resilient to future changes.
 * mpu6050
   - Delete MPU9150 from supported SPI devices as doesn't provide SPI.
   - Select I2C_MUX again after kbuild issue fixed elsewhere.
 * stm32-timer
   - Drop an unnecessary register update.
 * ssp_sensors
   - Convert to GPIO descriptors.
 * st_sensors
   - drop !CONFIG_ACPI defines as ACPI_PTR() will stop them being used
     anyway.
   - Make default platform data structures __maybe_unsued.
   - Fill in some missing kernel-doc function parameters.
 * st_lsm6dsx
   - white space fixes.
   - Mark some constants that aren't always used as __maybe_unused.
   - Drop of ID table guards as they just pervent use under ACPI.
   - Switch to device properties to allow ACPI usage.
 * st_uvis25
   - Drop acpi.h include as no ACPI APIs used.
 * ti-ads1015
   - Drop legacy platform data as no one seems to be using it.
   - Use the device property API instead of OF specific.
 * ti-ads7950
   - typo fix in error message.
 -----BEGIN PGP SIGNATURE-----
 
 iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAl4R2mwRHGppYzIzQGtl
 cm5lbC5vcmcACgkQVIU0mcT0Fogfow//Rfsrd2oiAwy4ypm70ZWGnr84C3O/Vpic
 Agwdd2/lHiCA2Gjg+n7ZT6XkKQmKiojuBMT05PuskEm5onJVQuSAKMVppXwU6UDP
 uOUS5MAbo87GLogzXJnAR/eCrx/VkC4UqFRBSi7IUIj+lTpjiOhmoqm78VTMxkgT
 hvp5PVN/mLNxNV3eVrR9uILjZLpbBjKjWil00IS2zj0o78sGtd2QtMIdTbn3iBLp
 m0ngCDww1KDH+idwbOIn8YX8GSK8mTjNV5q4r9+xnjoAk8RPk+H317idyRHCKfCM
 wWFSFB6u/oqtHXRgQVi3ndRrZnPLTycA/R20f3ezzhVYZzf3RpH8Upcx0lqqCmrB
 +ZTbYW1L7KL6zCSR4ZYIEmw2TeQngfCGy0yDoEDXm9V8/B2nGWFc3Iknq+fK415V
 7OgJCWAw6ybF2LZfJHpcuJTb0EPxCKnInHbRsaxCsSAPRyERSdAz8RLn3lpH/k2D
 X32Q9hz/6sXKzIAD1Y0jv8ll28D5S7d2FgaWufy1tpB+CMb0Mp0RQn+Ho8lNMh70
 Zh9SF8RvknAiCT9iHeVIdbJxoYEtMuCaDwScliukVcg12gVViY5VzXMbSV/4jCnZ
 bAVZDpcM3LVLxCGbWqCNxjQ9wle99LsVHRld/KDpOfI6VIYDb8Y900Nf6efkQkAs
 a6z6rhpVdDg=
 =8FmM
 -----END PGP SIGNATURE-----

Merge tag 'iio-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

First set of new device support, features and cleanups for IIO in the 5.6 cycle

New device support

* ad7091r5 ADC
  - New driver with follow up patch adding scale and vref support.
  - DT bindings
* ad7923
  - Support for ad7908, ad7918 and ad7928 added to driver.
* bma180
  - Support the BMA254 accelerometer. Required fairly substantial rework
    to allow for small differences between this an existing parts.
* bma400 accelerometer
  - New driver with follow up patch for regulator support.
  - DT bindings.
* asc dlhl60d
  - New driver support this range of pressure and temperature sensors.
  - DT bindings.
* ltc2496 ADC
  - New driver to support this ADC.
  - Split the existing LTC2497 driver generic component out and reuse.
  - DT bindings.
* parallax ping
  - New driver supporting ultrasonic and laser tof distance sensors.
  - Bindings for these sensors.

New features

* core
  - New char type for read_raw returns, used for thermocouple types.
  - Rename read_first_n callback to read.   The reasons behind the original
    naming are lost to the mists of time.
* ad799x
  - Allow pm_ops to disable device completely allowing regulator power down.
* bma180
  - Enable basic regulator support.
* dmaengine buffer
  - Report platform data alignment requirements via new ABI.
* max31856
  - Add option to set mains filter rejection frequency and document
    new in_temp_filter_notch_center_frequency ABI.
  - Add support for configuring HW averaging (oversampling ratio)
  - Add runtime configuration of thermocouple type and document new ABI.
* maxim-thermocouple
  - Add read only access to thermocouple type using new ABI, includes
    adding more specific compatibles to reflect which variant of the
    chip is being used.
* mpu6050
  - Provide option to support the PMU9150 in package magnetometer directly
    rather than via auxiliary bus.
* stm32_adc
  - Add overrun interrupt checks to detect if this happens.
* st_lsm6dsx
  - Enable the sensor-hub support for lsm6dsm. Includes various reworks to
    allow this.

Cleanups and minor fixes

* Subsystem wide
  - Tidy up indentation in Kconfig and fix alphabetical order of AD7091R5.
  - Drop linux/gpio.h and linux/of_gpio.h from drivers that don't use them.
* ad7266
  - Convert to GPIO descriptors.
* ad7303
  - Avoid a dance with checking if the regulator is supplied by just
    using the optional request interface.
* ad7887
  - Simplify channel specification assignment to enable adding more devices.
* ad7923
  - Drop some unused and largely pointless defines of BOB_N==N variety.
  - Tidy up checkpatch warnings.
  - Add missing of_device_id table.
* adf4350
  - Convert to GPIO descriptors.
* ak8975
  - Convert to GPIO descriptors.
* ADIS library and drivers
  - Expand scope of txrx_lock to cover all state and rename as state_lock
  - Add unlocked read / write to allow grouping of consecutive calls under
    single lock / unlock.
  - Add unlocked check_status, reset to allow grouping under single
    lock / unlock.
  - Remove remaining uses of core mlock for local state protection.
    mlock should never be used directly as it protects tightly defined
    core IIO device management state.
* adis16240
  - Enforce only supported SPI mode on driver load + add DT binding doc.
* atlas-ph-sensor
  - Rename to atlas-sensor given it now covers things beyond ph sensors.
* bma180
  - Use local dev variable to tidy up code.
  - Use c99 style explicity .member assignment to make driver more readable.
* bmp280
  - Drop ACPI support. No evidence this was used and appropriate ID is not
    registered.
  - Allow ACPI to bind device via PRP0001
* dmaengine buffer
  - Use dma_request_chan instead of dma_request_slave_channel_reason as that
    ABI is going away.
  - Add module info to avoid tainting the kernel.
* hts221
  - Avoid magic number defines when only used to fill structure elements
    that are self describing.
* lm3533
  - Drop a stray semicolon.
* max9611
  - Cleanup enum handling to be more resilient to future changes.
* mpu6050
  - Delete MPU9150 from supported SPI devices as doesn't provide SPI.
  - Select I2C_MUX again after kbuild issue fixed elsewhere.
* stm32-timer
  - Drop an unnecessary register update.
* ssp_sensors
  - Convert to GPIO descriptors.
* st_sensors
  - drop !CONFIG_ACPI defines as ACPI_PTR() will stop them being used
    anyway.
  - Make default platform data structures __maybe_unsued.
  - Fill in some missing kernel-doc function parameters.
* st_lsm6dsx
  - white space fixes.
  - Mark some constants that aren't always used as __maybe_unused.
  - Drop of ID table guards as they just pervent use under ACPI.
  - Switch to device properties to allow ACPI usage.
* st_uvis25
  - Drop acpi.h include as no ACPI APIs used.
* ti-ads1015
  - Drop legacy platform data as no one seems to be using it.
  - Use the device property API instead of OF specific.
* ti-ads7950
  - typo fix in error message.

* tag 'iio-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (99 commits)
  iio: accel: bma180: BMA254 support
  iio: pressure: bmp280: Allow device to be enumerated from ACPI
  iio: pressure: bmp280: Drop ACPI support
  dt-bindings: iio: adc: convert sd modulator to json-schema
  iio: buffer: rename 'read_first_n' callback to 'read'
  iio: buffer-dmaengine: Report buffer length requirements
  bindings: iio: pressure: Add documentation for dlh driver
  dt-bindings: Add asc vendor
  iio: pressure: Add driver for DLH pressure sensors
  iio: buffer-dmaengine: Add module information
  iio: accel: bma180: Use explicit member assignment
  iio: accel: bma180: Basic regulator support
  iio: accel: bma180: Add dev helper variable
  iio: imu: st_lsm6dsx: enable sensor-hub support for lsm6dsm
  iio: imu: st_lsm6dsx: rename st_lsm6dsx_shub_read_reg in st_lsm6dsx_shub_read_output
  iio: imu: st_lsm6dsx: check if shub_output reg is located in primary page
  iio: imu: st_lsm6dsx: check if pull_up is located in primary page
  iio: imu: st_lsm6dsx: check if master_enable is located in primary page
  iio: imu: st_lsm6dsx: export max num of slave devices in st_lsm6dsx_shub_settings
  iio: light: remove unneeded semicolon
  ...
2020-01-10 10:44:00 +01:00
..
accel First set of new device support, features and cleanups for IIO in the 5.6 cycle 2020-01-10 10:44:00 +01:00
adc First set of new device support, features and cleanups for IIO in the 5.6 cycle 2020-01-10 10:44:00 +01:00
afe treewide: Add SPDX license identifier - Makefile/Kconfig 2019-05-21 10:50:46 +02:00
amplifiers Second set of IIO device support, features, cleanups and minor fixes for 5.3. 2019-07-01 10:58:13 +02:00
buffer iio: buffer: rename 'read_first_n' callback to 'read' 2019-12-29 15:20:09 +00:00
chemical iio: chemical: atlas-ph-sensor: rename atlas-ph-sensor to atlas-sensor 2019-12-29 15:20:06 +00:00
common First set of new device support, features and cleanups for IIO in the 5.6 cycle 2020-01-10 10:44:00 +01:00
dac iio: ad5592r: Drop surplus GPIO header 2019-12-15 11:42:16 +00:00
dummy spi: docs: convert to ReST and add it to the kABI bookset 2019-07-31 14:13:13 -06:00
frequency iio: adf4350: Convert to use GPIO descriptor 2019-12-15 11:42:16 +00:00
gyro iio: gyro: st_gyro: Mark gyro_pdata with __maybe_unused 2019-12-29 15:20:05 +00:00
health treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 174 2019-05-30 11:26:41 -07:00
humidity First set of new device support, features and cleanups for IIO in the 5.6 cycle 2020-01-10 10:44:00 +01:00
imu First set of new device support, features and cleanups for IIO in the 5.6 cycle 2020-01-10 10:44:00 +01:00
light First set of new device support, features and cleanups for IIO in the 5.6 cycle 2020-01-10 10:44:00 +01:00
magnetometer iio: ak8975: Convert to use GPIO descriptor 2019-12-15 11:42:14 +00:00
multiplexer treewide: Add SPDX license identifier - Makefile/Kconfig 2019-05-21 10:50:46 +02:00
orientation treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 309 2019-06-05 17:37:04 +02:00
potentiometer iio: potentiometer: add a driver for Maxim 5432-5435 2019-08-05 14:25:08 +01:00
potentiostat treewide: Add SPDX license identifier - Makefile/Kconfig 2019-05-21 10:50:46 +02:00
pressure iio: pressure: bmp280: Allow device to be enumerated from ACPI 2019-12-29 15:20:10 +00:00
proximity iio: as3935: Drop GPIO includes 2019-12-15 11:42:15 +00:00
resolver iio: ad2s1200: Drop legacy include 2019-12-15 11:42:15 +00:00
temperature First set of new device support, features and cleanups for IIO in the 5.6 cycle 2020-01-10 10:44:00 +01:00
trigger iio: trigger: stm32-timer: remove unnecessary update event 2019-12-01 10:20:21 +00:00
iio_core_trigger.h treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500 2019-06-19 17:09:55 +02:00
iio_core.h iio: buffer: rename 'read_first_n' callback to 'read' 2019-12-29 15:20:09 +00:00
industrialio-buffer.c iio: buffer: rename 'read_first_n' callback to 'read' 2019-12-29 15:20:09 +00:00
industrialio-configfs.c treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500 2019-06-19 17:09:55 +02:00
industrialio-core.c First set of new device support, features and cleanups for IIO in the 5.6 cycle 2020-01-10 10:44:00 +01:00
industrialio-event.c treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500 2019-06-19 17:09:55 +02:00
industrialio-sw-device.c treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500 2019-06-19 17:09:55 +02:00
industrialio-sw-trigger.c treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500 2019-06-19 17:09:55 +02:00
industrialio-trigger.c treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500 2019-06-19 17:09:55 +02:00
industrialio-triggered-event.c treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152 2019-05-30 11:26:32 -07:00
inkern.c Driver Core and debugfs changes for 5.3-rc1 2019-07-12 12:24:03 -07:00
Kconfig Second set of IIO device support, features, cleanups and minor fixes for 5.3. 2019-07-01 10:58:13 +02:00
Makefile counter: stm32-lptimer: add counter device 2019-04-25 21:33:41 +02:00