mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-27 21:14:44 +08:00
1004a2977b
Use the new EBI/NAND bindings to declare NAND chips and remove old NAND nodes along the way. Note that we keep using old bindings in at91rm9200.dtsi because this SoC is not supported by the EBI driver. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Tested-by: Peter Rosin <peda@axentia.se> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
144 lines
2.7 KiB
Plaintext
144 lines
2.7 KiB
Plaintext
/*
|
|
* at91-cosino.dtsi - Device Tree file for Cosino core module
|
|
*
|
|
* Copyright (C) 2013 - Rodolfo Giometti <giometti@linux.it>
|
|
* HCE Engineering
|
|
*
|
|
* Derived from at91sam9x5ek.dtsi by:
|
|
* Copyright (C) 2012 Atmel,
|
|
* 2012 Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
*
|
|
* Licensed under GPLv2 or later.
|
|
*/
|
|
|
|
#include "at91sam9g35.dtsi"
|
|
|
|
/ {
|
|
model = "HCE Cosino core module";
|
|
compatible = "hce,cosino", "atmel,at91sam9x5", "atmel,at91sam9";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait";
|
|
};
|
|
|
|
memory {
|
|
reg = <0x20000000 0x8000000>;
|
|
};
|
|
|
|
clocks {
|
|
slow_xtal {
|
|
clock-frequency = <32768>;
|
|
};
|
|
|
|
main_xtal {
|
|
clock-frequency = <12000000>;
|
|
};
|
|
};
|
|
|
|
ahb {
|
|
apb {
|
|
mmc0: mmc@f0008000 {
|
|
pinctrl-0 = <
|
|
&pinctrl_board_mmc0
|
|
&pinctrl_mmc0_slot0_clk_cmd_dat0
|
|
&pinctrl_mmc0_slot0_dat1_3>;
|
|
status = "okay";
|
|
slot@0 {
|
|
reg = <0>;
|
|
bus-width = <4>;
|
|
cd-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
dbgu: serial@fffff200 {
|
|
status = "okay";
|
|
};
|
|
|
|
usart0: serial@f801c000 {
|
|
status = "okay";
|
|
};
|
|
|
|
i2c0: i2c@f8010000 {
|
|
status = "okay";
|
|
};
|
|
|
|
adc0: adc@f804c000 {
|
|
atmel,adc-ts-wires = <4>;
|
|
atmel,adc-ts-pressure-threshold = <10000>;
|
|
status = "okay";
|
|
};
|
|
|
|
pinctrl@fffff400 {
|
|
mmc0 {
|
|
pinctrl_board_mmc0: mmc0-board {
|
|
atmel,pins =
|
|
<AT91_PIOD 15 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD15 gpio CD pin pull up and deglitch */
|
|
};
|
|
};
|
|
};
|
|
|
|
watchdog@fffffe40 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
ebi: ebi@10000000 {
|
|
pinctrl-0 = <&pinctrl_ebi_addr_nand
|
|
&pinctrl_ebi_data_0_7>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
|
|
nand_controller: nand-controller {
|
|
status = "okay";
|
|
pinctrl-0 = <&pinctrl_nand_oe_we
|
|
&pinctrl_nand_cs
|
|
&pinctrl_nand_rb>;
|
|
pinctrl-names = "default";
|
|
|
|
nand@3 {
|
|
reg = <0x3 0x0 0x800000>;
|
|
rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>;
|
|
cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>;
|
|
nand-bus-width = <8>;
|
|
nand-ecc-mode = "hw";
|
|
nand-ecc-strength = <4>;
|
|
nand-ecc-step-size = <512>;
|
|
nand-on-flash-bbt;
|
|
label = "atmel_nand";
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
at91bootstrap@0 {
|
|
label = "at91bootstrap";
|
|
reg = <0x0 0x40000>;
|
|
};
|
|
|
|
uboot@40000 {
|
|
label = "u-boot";
|
|
reg = <0x40000 0x80000>;
|
|
};
|
|
|
|
ubootenv@c0000 {
|
|
label = "U-Boot Env";
|
|
reg = <0xc0000 0x140000>;
|
|
};
|
|
|
|
kernel@200000 {
|
|
label = "kernel";
|
|
reg = <0x200000 0x600000>;
|
|
};
|
|
|
|
rootfs@800000 {
|
|
label = "rootfs";
|
|
reg = <0x800000 0x0f800000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|