mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-26 04:25:27 +08:00
1126e108a3
Enable ostm0 and ostm1 timers to be used as clock source and clockevent source. The timers provides greater accuracy than the already enabled mtu2 one. With these enabled: clocksource: ostm: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 57352151442 ns sched_clock: 32 bits at 33MHz, resolution 30ns, wraps every 64440619504ns ostm: used for clocksource ostm: used for clock events Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Suggested-by: Chris Brandt <chris.brandt@renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
138 lines
2.8 KiB
Plaintext
138 lines
2.8 KiB
Plaintext
/*
|
|
* Device Tree Source for the GR-Peach board
|
|
*
|
|
* Copyright (C) 2017 Jacopo Mondi <jacopo+renesas@jmondi.org>
|
|
* Copyright (C) 2016 Renesas Electronics
|
|
*
|
|
* This file is licensed under the terms of the GNU General Public License
|
|
* version 2. This program is licensed "as is" without any warranty of any
|
|
* kind, whether express or implied.
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include "r7s72100.dtsi"
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/pinctrl/r7s72100-pinctrl.h>
|
|
|
|
/ {
|
|
model = "GR-Peach";
|
|
compatible = "renesas,gr-peach", "renesas,r7s72100";
|
|
|
|
aliases {
|
|
serial0 = &scif2;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "ignore_loglevel rw root=/dev/mtdblock0";
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
memory@20000000 {
|
|
device_type = "memory";
|
|
reg = <0x20000000 0x00a00000>;
|
|
};
|
|
|
|
lbsc {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
};
|
|
|
|
flash@18000000 {
|
|
compatible = "mtd-rom";
|
|
probe-type = "map_rom";
|
|
reg = <0x18000000 0x00800000>;
|
|
bank-width = <4>;
|
|
device-width = <1>;
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
rootfs@600000 {
|
|
label = "rootfs";
|
|
reg = <0x00600000 0x00200000>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
status = "okay";
|
|
compatible = "gpio-leds";
|
|
|
|
led1 {
|
|
gpios = <&port6 12 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pinctrl {
|
|
scif2_pins: serial2 {
|
|
/* P6_2 as RxD2; P6_3 as TxD2 */
|
|
pinmux = <RZA1_PINMUX(6, 2, 7)>, <RZA1_PINMUX(6, 3, 7)>;
|
|
};
|
|
|
|
ether_pins: ether {
|
|
/* Ethernet on Ports 1,3,5,10 */
|
|
pinmux = <RZA1_PINMUX(1, 14, 4)>, /* P1_14 = ET_COL */
|
|
<RZA1_PINMUX(3, 0, 2)>, /* P3_0 = ET_TXCLK */
|
|
<RZA1_PINMUX(3, 3, 2)>, /* P3_3 = ET_MDIO */
|
|
<RZA1_PINMUX(3, 4, 2)>, /* P3_4 = ET_RXCLK */
|
|
<RZA1_PINMUX(3, 5, 2)>, /* P3_5 = ET_RXER */
|
|
<RZA1_PINMUX(3, 6, 2)>, /* P3_6 = ET_RXDV */
|
|
<RZA1_PINMUX(5, 9, 2)>, /* P5_9 = ET_MDC */
|
|
<RZA1_PINMUX(10, 1, 4)>, /* P10_1 = ET_TXER */
|
|
<RZA1_PINMUX(10, 2, 4)>, /* P10_2 = ET_TXEN */
|
|
<RZA1_PINMUX(10, 3, 4)>, /* P10_3 = ET_CRS */
|
|
<RZA1_PINMUX(10, 4, 4)>, /* P10_4 = ET_TXD0 */
|
|
<RZA1_PINMUX(10, 5, 4)>, /* P10_5 = ET_TXD1 */
|
|
<RZA1_PINMUX(10, 6, 4)>, /* P10_6 = ET_TXD2 */
|
|
<RZA1_PINMUX(10, 7, 4)>, /* P10_7 = ET_TXD3 */
|
|
<RZA1_PINMUX(10, 8, 4)>, /* P10_8 = ET_RXD0 */
|
|
<RZA1_PINMUX(10, 9, 4)>, /* P10_9 = ET_RXD1 */
|
|
<RZA1_PINMUX(10, 10, 4)>,/* P10_10 = ET_RXD2 */
|
|
<RZA1_PINMUX(10, 11, 4)>;/* P10_11 = ET_RXD3 */
|
|
};
|
|
};
|
|
|
|
&extal_clk {
|
|
clock-frequency = <13333000>;
|
|
};
|
|
|
|
&usb_x1_clk {
|
|
clock-frequency = <48000000>;
|
|
};
|
|
|
|
&mtu2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&ostm0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&ostm1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&scif2 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&scif2_pins>;
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
ðer {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <ðer_pins>;
|
|
|
|
status = "okay";
|
|
|
|
renesas,no-ether-link;
|
|
phy-handle = <&phy0>;
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
|
|
reset-gpios = <&port4 2 GPIO_ACTIVE_LOW>;
|
|
reset-delay-us = <5>;
|
|
};
|
|
};
|