mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-23 02:54:32 +08:00
a33f32244d
Fix obvious cases of "it's" being used when "its" was meant. Signed-off-by: Francis Galiegue <fgaliegue@gmail.com> Acked-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
128 lines
4.9 KiB
Plaintext
128 lines
4.9 KiB
Plaintext
|
|
Hypervisor-Assisted Dump
|
|
------------------------
|
|
November 2007
|
|
|
|
The goal of hypervisor-assisted dump is to enable the dump of
|
|
a crashed system, and to do so from a fully-reset system, and
|
|
to minimize the total elapsed time until the system is back
|
|
in production use.
|
|
|
|
As compared to kdump or other strategies, hypervisor-assisted
|
|
dump offers several strong, practical advantages:
|
|
|
|
-- Unlike kdump, the system has been reset, and loaded
|
|
with a fresh copy of the kernel. In particular,
|
|
PCI and I/O devices have been reinitialized and are
|
|
in a clean, consistent state.
|
|
-- As the dump is performed, the dumped memory becomes
|
|
immediately available to the system for normal use.
|
|
-- After the dump is completed, no further reboots are
|
|
required; the system will be fully usable, and running
|
|
in its normal, production mode on its normal kernel.
|
|
|
|
The above can only be accomplished by coordination with,
|
|
and assistance from the hypervisor. The procedure is
|
|
as follows:
|
|
|
|
-- When a system crashes, the hypervisor will save
|
|
the low 256MB of RAM to a previously registered
|
|
save region. It will also save system state, system
|
|
registers, and hardware PTE's.
|
|
|
|
-- After the low 256MB area has been saved, the
|
|
hypervisor will reset PCI and other hardware state.
|
|
It will *not* clear RAM. It will then launch the
|
|
bootloader, as normal.
|
|
|
|
-- The freshly booted kernel will notice that there
|
|
is a new node (ibm,dump-kernel) in the device tree,
|
|
indicating that there is crash data available from
|
|
a previous boot. It will boot into only 256MB of RAM,
|
|
reserving the rest of system memory.
|
|
|
|
-- Userspace tools will parse /sys/kernel/release_region
|
|
and read /proc/vmcore to obtain the contents of memory,
|
|
which holds the previous crashed kernel. The userspace
|
|
tools may copy this info to disk, or network, nas, san,
|
|
iscsi, etc. as desired.
|
|
|
|
For Example: the values in /sys/kernel/release-region
|
|
would look something like this (address-range pairs).
|
|
CPU:0x177fee000-0x10000: HPTE:0x177ffe020-0x1000: /
|
|
DUMP:0x177fff020-0x10000000, 0x10000000-0x16F1D370A
|
|
|
|
-- As the userspace tools complete saving a portion of
|
|
dump, they echo an offset and size to
|
|
/sys/kernel/release_region to release the reserved
|
|
memory back to general use.
|
|
|
|
An example of this is:
|
|
"echo 0x40000000 0x10000000 > /sys/kernel/release_region"
|
|
which will release 256MB at the 1GB boundary.
|
|
|
|
Please note that the hypervisor-assisted dump feature
|
|
is only available on Power6-based systems with recent
|
|
firmware versions.
|
|
|
|
Implementation details:
|
|
----------------------
|
|
|
|
During boot, a check is made to see if firmware supports
|
|
this feature on this particular machine. If it does, then
|
|
we check to see if a active dump is waiting for us. If yes
|
|
then everything but 256 MB of RAM is reserved during early
|
|
boot. This area is released once we collect a dump from user
|
|
land scripts that are run. If there is dump data, then
|
|
the /sys/kernel/release_region file is created, and
|
|
the reserved memory is held.
|
|
|
|
If there is no waiting dump data, then only the highest
|
|
256MB of the ram is reserved as a scratch area. This area
|
|
is *not* released: this region will be kept permanently
|
|
reserved, so that it can act as a receptacle for a copy
|
|
of the low 256MB in the case a crash does occur. See,
|
|
however, "open issues" below, as to whether
|
|
such a reserved region is really needed.
|
|
|
|
Currently the dump will be copied from /proc/vmcore to a
|
|
a new file upon user intervention. The starting address
|
|
to be read and the range for each data point in provided
|
|
in /sys/kernel/release_region.
|
|
|
|
The tools to examine the dump will be same as the ones
|
|
used for kdump.
|
|
|
|
General notes:
|
|
--------------
|
|
Security: please note that there are potential security issues
|
|
with any sort of dump mechanism. In particular, plaintext
|
|
(unencrypted) data, and possibly passwords, may be present in
|
|
the dump data. Userspace tools must take adequate precautions to
|
|
preserve security.
|
|
|
|
Open issues/ToDo:
|
|
------------
|
|
o The various code paths that tell the hypervisor that a crash
|
|
occurred, vs. it simply being a normal reboot, should be
|
|
reviewed, and possibly clarified/fixed.
|
|
|
|
o Instead of using /sys/kernel, should there be a /sys/dump
|
|
instead? There is a dump_subsys being created by the s390 code,
|
|
perhaps the pseries code should use a similar layout as well.
|
|
|
|
o Is reserving a 256MB region really required? The goal of
|
|
reserving a 256MB scratch area is to make sure that no
|
|
important crash data is clobbered when the hypervisor
|
|
save low mem to the scratch area. But, if one could assure
|
|
that nothing important is located in some 256MB area, then
|
|
it would not need to be reserved. Something that can be
|
|
improved in subsequent versions.
|
|
|
|
o Still working the kdump team to integrate this with kdump,
|
|
some work remains but this would not affect the current
|
|
patches.
|
|
|
|
o Still need to write a shell script, to copy the dump away.
|
|
Currently I am parsing it manually.
|