mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-16 08:44:21 +08:00
1da177e4c3
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
1512 lines
42 KiB
Plaintext
1512 lines
42 KiB
Plaintext
February 2003 Kernel Parameters v2.5.59
|
|
~~~~~~~~~~~~~~~~~
|
|
|
|
The following is a consolidated list of the kernel parameters as implemented
|
|
(mostly) by the __setup() macro and sorted into English Dictionary order
|
|
(defined as ignoring all punctuation and sorting digits before letters in a
|
|
case insensitive manner), and with descriptions where known.
|
|
|
|
Module parameters for loadable modules are specified only as the
|
|
parameter name with optional '=' and value as appropriate, such as:
|
|
|
|
modprobe usbcore blinkenlights=1
|
|
|
|
Module parameters for modules that are built into the kernel image
|
|
are specified on the kernel command line with the module name plus
|
|
'.' plus parameter name, with '=' and value if appropriate, such as:
|
|
|
|
usbcore.blinkenlights=1
|
|
|
|
The text in square brackets at the beginning of the description state the
|
|
restrictions on the kernel for the said kernel parameter to be valid. The
|
|
restrictions referred to are that the relevant option is valid if:
|
|
|
|
ACPI ACPI support is enabled.
|
|
ALSA ALSA sound support is enabled.
|
|
APIC APIC support is enabled.
|
|
APM Advanced Power Management support is enabled.
|
|
AX25 Appropriate AX.25 support is enabled.
|
|
CD Appropriate CD support is enabled.
|
|
DEVFS devfs support is enabled.
|
|
DRM Direct Rendering Management support is enabled.
|
|
EDD BIOS Enhanced Disk Drive Services (EDD) is enabled
|
|
EFI EFI Partitioning (GPT) is enabled
|
|
EIDE EIDE/ATAPI support is enabled.
|
|
FB The frame buffer device is enabled.
|
|
HW Appropriate hardware is enabled.
|
|
IA-32 IA-32 aka i386 architecture is enabled.
|
|
IA-64 IA-64 architecture is enabled.
|
|
IOSCHED More than one I/O scheduler is enabled.
|
|
IP_PNP IP DCHP, BOOTP, or RARP is enabled.
|
|
ISAPNP ISA PnP code is enabled.
|
|
ISDN Appropriate ISDN support is enabled.
|
|
JOY Appropriate joystick support is enabled.
|
|
LP Printer support is enabled.
|
|
LOOP Loopback device support is enabled.
|
|
M68k M68k architecture is enabled.
|
|
These options have more detailed description inside of
|
|
Documentation/m68k/kernel-options.txt.
|
|
MCA MCA bus support is enabled.
|
|
MDA MDA console support is enabled.
|
|
MOUSE Appropriate mouse support is enabled.
|
|
MTD MTD support is enabled.
|
|
NET Appropriate network support is enabled.
|
|
NUMA NUMA support is enabled.
|
|
NFS Appropriate NFS support is enabled.
|
|
OSS OSS sound support is enabled.
|
|
PARIDE The ParIDE subsystem is enabled.
|
|
PARISC The PA-RISC architecture is enabled.
|
|
PCI PCI bus support is enabled.
|
|
PCMCIA The PCMCIA subsystem is enabled.
|
|
PNP Plug & Play support is enabled.
|
|
PPC PowerPC architecture is enabled.
|
|
PPT Parallel port support is enabled.
|
|
PS2 Appropriate PS/2 support is enabled.
|
|
RAM RAM disk support is enabled.
|
|
S390 S390 architecture is enabled.
|
|
SCSI Appropriate SCSI support is enabled.
|
|
A lot of drivers has their options described inside of
|
|
Documentation/scsi/.
|
|
SELINUX SELinux support is enabled.
|
|
SERIAL Serial support is enabled.
|
|
SMP The kernel is an SMP kernel.
|
|
SPARC Sparc architecture is enabled.
|
|
SWSUSP Software suspension is enabled.
|
|
TS Appropriate touchscreen support is enabled.
|
|
USB USB support is enabled.
|
|
USBHID USB Human Interface Device support is enabled.
|
|
V4L Video For Linux support is enabled.
|
|
VGA The VGA console has been enabled.
|
|
VT Virtual terminal support is enabled.
|
|
WDT Watchdog support is enabled.
|
|
XT IBM PC/XT MFM hard disk support is enabled.
|
|
X86-64 X86-64 architecture is enabled.
|
|
More X86-64 boot options can be found in
|
|
Documentation/x86_64/boot-options.txt .
|
|
|
|
In addition, the following text indicates that the option:
|
|
|
|
BUGS= Relates to possible processor bugs on the said processor.
|
|
KNL Is a kernel start-up parameter.
|
|
BOOT Is a boot loader parameter.
|
|
|
|
Parameters denoted with BOOT are actually interpreted by the boot
|
|
loader, and have no meaning to the kernel directly.
|
|
Do not modify the syntax of boot loader parameters without extreme
|
|
need or coordination with <Documentation/i386/boot.txt>.
|
|
|
|
Note that ALL kernel parameters listed below are CASE SENSITIVE, and that
|
|
a trailing = on the name of any parameter states that that parameter will
|
|
be entered as an environment variable, whereas its absence indicates that
|
|
it will appear as a kernel argument readable via /proc/cmdline by programs
|
|
running once the system is up.
|
|
|
|
53c7xx= [HW,SCSI] Amiga SCSI controllers
|
|
See header of drivers/scsi/53c7xx.c.
|
|
See also Documentation/scsi/ncr53c7xx.txt.
|
|
|
|
acpi= [HW,ACPI] Advanced Configuration and Power Interface
|
|
Format: { force | off | ht | strict }
|
|
force -- enable ACPI if default was off
|
|
off -- disable ACPI if default was on
|
|
noirq -- do not use ACPI for IRQ routing
|
|
ht -- run only enough ACPI to enable Hyper Threading
|
|
strict -- Be less tolerant of platforms that are not
|
|
strictly ACPI specification compliant.
|
|
|
|
See also Documentation/pm.txt, pci=noacpi
|
|
|
|
acpi_sleep= [HW,ACPI] Sleep options
|
|
Format: { s3_bios, s3_mode }
|
|
See Documentation/power/video.txt
|
|
|
|
acpi_sci= [HW,ACPI] ACPI System Control Interrupt trigger mode
|
|
Format: { level | edge | high | low }
|
|
|
|
acpi_irq_balance [HW,ACPI] ACPI will balance active IRQs
|
|
default in APIC mode
|
|
|
|
acpi_irq_nobalance [HW,ACPI] ACPI will not move active IRQs (default)
|
|
default in PIC mode
|
|
|
|
acpi_irq_pci= [HW,ACPI] If irq_balance, Clear listed IRQs for use by PCI
|
|
Format: <irq>,<irq>...
|
|
|
|
acpi_irq_isa= [HW,ACPI] If irq_balance, Mark listed IRQs used by ISA
|
|
Format: <irq>,<irq>...
|
|
|
|
acpi_osi= [HW,ACPI] empty param disables _OSI
|
|
|
|
acpi_serialize [HW,ACPI] force serialization of AML methods
|
|
|
|
acpi_skip_timer_override [HW,ACPI]
|
|
Recognize and ignore IRQ0/pin2 Interrupt Override.
|
|
For broken nForce2 BIOS resulting in XT-PIC timer.
|
|
|
|
acpi_dbg_layer= [HW,ACPI]
|
|
Format: <int>
|
|
Each bit of the <int> indicates an acpi debug layer,
|
|
1: enable, 0: disable. It is useful for boot time
|
|
debugging. After system has booted up, it can be set
|
|
via /proc/acpi/debug_layer.
|
|
|
|
acpi_dbg_level= [HW,ACPI]
|
|
Format: <int>
|
|
Each bit of the <int> indicates an acpi debug level,
|
|
1: enable, 0: disable. It is useful for boot time
|
|
debugging. After system has booted up, it can be set
|
|
via /proc/acpi/debug_level.
|
|
|
|
acpi_fake_ecdt [HW,ACPI] Workaround failure due to BIOS lacking ECDT
|
|
|
|
ad1816= [HW,OSS]
|
|
Format: <io>,<irq>,<dma>,<dma2>
|
|
See also Documentation/sound/oss/AD1816.
|
|
|
|
ad1848= [HW,OSS]
|
|
Format: <io>,<irq>,<dma>,<dma2>,<type>
|
|
|
|
adlib= [HW,OSS]
|
|
Format: <io>
|
|
|
|
advansys= [HW,SCSI]
|
|
See header of drivers/scsi/advansys.c.
|
|
|
|
advwdt= [HW,WDT] Advantech WDT
|
|
Format: <iostart>,<iostop>
|
|
|
|
aedsp16= [HW,OSS] Audio Excel DSP 16
|
|
Format: <io>,<irq>,<dma>,<mss_io>,<mpu_io>,<mpu_irq>
|
|
See also header of sound/oss/aedsp16.c.
|
|
|
|
aha152x= [HW,SCSI]
|
|
See Documentation/scsi/aha152x.txt.
|
|
|
|
aha1542= [HW,SCSI]
|
|
Format: <portbase>[,<buson>,<busoff>[,<dmaspeed>]]
|
|
|
|
aic7xxx= [HW,SCSI]
|
|
See Documentation/scsi/aic7xxx.txt.
|
|
|
|
aic79xx= [HW,SCSI]
|
|
See Documentation/scsi/aic79xx.txt.
|
|
|
|
AM53C974= [HW,SCSI]
|
|
Format: <host-scsi-id>,<target-scsi-id>,<max-rate>,<max-offset>
|
|
See also header of drivers/scsi/AM53C974.c.
|
|
|
|
amijoy.map= [HW,JOY] Amiga joystick support
|
|
Map of devices attached to JOY0DAT and JOY1DAT
|
|
Format: <a>,<b>
|
|
See also Documentation/kernel/input/joystick.txt
|
|
|
|
analog.map= [HW,JOY] Analog joystick and gamepad support
|
|
Specifies type or capabilities of an analog joystick
|
|
connected to one of 16 gameports
|
|
Format: <type1>,<type2>,..<type16>
|
|
|
|
apc= [HW,SPARC] Power management functions (SPARCstation-4/5 + deriv.)
|
|
Format: noidle
|
|
Disable APC CPU standby support. SPARCstation-Fox does
|
|
not play well with APC CPU idle - disable it if you have
|
|
APC and your system crashes randomly.
|
|
|
|
apic= [APIC,i386] Change the output verbosity whilst booting
|
|
Format: { quiet (default) | verbose | debug }
|
|
Change the amount of debugging information output
|
|
when initialising the APIC and IO-APIC components.
|
|
|
|
apm= [APM] Advanced Power Management
|
|
See header of arch/i386/kernel/apm.c.
|
|
|
|
applicom= [HW]
|
|
Format: <mem>,<irq>
|
|
|
|
arcrimi= [HW,NET] ARCnet - "RIM I" (entirely mem-mapped) cards
|
|
Format: <io>,<irq>,<nodeID>
|
|
|
|
ataflop= [HW,M68k]
|
|
|
|
atarimouse= [HW,MOUSE] Atari Mouse
|
|
|
|
atascsi= [HW,SCSI] Atari SCSI
|
|
|
|
atkbd.extra= [HW] Enable extra LEDs and keys on IBM RapidAccess,
|
|
EzKey and similar keyboards
|
|
|
|
atkbd.reset= [HW] Reset keyboard during initialization
|
|
|
|
atkbd.set= [HW] Select keyboard code set
|
|
Format: <int> (2 = AT (default) 3 = PS/2)
|
|
|
|
atkbd.scroll= [HW] Enable scroll wheel on MS Office and similar
|
|
keyboards
|
|
|
|
atkbd.softraw= [HW] Choose between synthetic and real raw mode
|
|
Format: <bool> (0 = real, 1 = synthetic (default))
|
|
|
|
atkbd.softrepeat=
|
|
[HW] Use software keyboard repeat
|
|
|
|
autotest [IA64]
|
|
|
|
awe= [HW,OSS] AWE32/SB32/AWE64 wave table synth
|
|
Format: <io>,<memsize>,<isapnp>
|
|
|
|
aztcd= [HW,CD] Aztech CD268 CDROM driver
|
|
Format: <io>,0x79 (?)
|
|
|
|
baycom_epp= [HW,AX25]
|
|
Format: <io>,<mode>
|
|
|
|
baycom_par= [HW,AX25] BayCom Parallel Port AX.25 Modem
|
|
Format: <io>,<mode>
|
|
See header of drivers/net/hamradio/baycom_par.c.
|
|
|
|
baycom_ser_fdx= [HW,AX25] BayCom Serial Port AX.25 Modem (Full Duplex Mode)
|
|
Format: <io>,<irq>,<mode>[,<baud>]
|
|
See header of drivers/net/hamradio/baycom_ser_fdx.c.
|
|
|
|
baycom_ser_hdx= [HW,AX25] BayCom Serial Port AX.25 Modem (Half Duplex Mode)
|
|
Format: <io>,<irq>,<mode>
|
|
See header of drivers/net/hamradio/baycom_ser_hdx.c.
|
|
|
|
blkmtd_device= [HW,MTD]
|
|
blkmtd_erasesz=
|
|
blkmtd_ro=
|
|
blkmtd_bs=
|
|
blkmtd_count=
|
|
|
|
bttv.card= [HW,V4L] bttv (bt848 + bt878 based grabber cards)
|
|
bttv.radio= Most important insmod options are available as kernel args too.
|
|
bttv.pll= See Documentation/video4linux/bttv/Insmod-options
|
|
bttv.tuner= and Documentation/video4linux/bttv/CARDLIST
|
|
|
|
BusLogic= [HW,SCSI]
|
|
See drivers/scsi/BusLogic.c, comment before function
|
|
BusLogic_ParseDriverOptions().
|
|
|
|
c101= [NET] Moxa C101 synchronous serial card
|
|
|
|
cachesize= [BUGS=IA-32] Override level 2 CPU cache size detection.
|
|
Sometimes CPU hardware bugs make them report the cache
|
|
size incorrectly. The kernel will attempt work arounds
|
|
to fix known problems, but for some CPUs it is not
|
|
possible to determine what the correct size should be.
|
|
This option provides an override for these situations.
|
|
|
|
cdu31a= [HW,CD]
|
|
Format: <io>,<irq>[,PAS]
|
|
See header of drivers/cdrom/cdu31a.c.
|
|
|
|
chandev= [HW,NET] Generic channel device initialisation
|
|
|
|
checkreqprot [SELINUX] Set initial checkreqprot flag value.
|
|
Format: { "0" | "1" }
|
|
See security/selinux/Kconfig help text.
|
|
0 -- check protection applied by kernel (includes any implied execute protection).
|
|
1 -- check protection requested by application.
|
|
Default value is set via a kernel config option.
|
|
Value can be changed at runtime via /selinux/checkreqprot.
|
|
|
|
clock= [BUGS=IA-32, HW] gettimeofday timesource override.
|
|
Forces specified timesource (if avaliable) to be used
|
|
when calculating gettimeofday(). If specicified timesource
|
|
is not avalible, it defaults to PIT.
|
|
Format: { pit | tsc | cyclone | pmtmr }
|
|
|
|
hpet= [IA-32,HPET] option to disable HPET and use PIT.
|
|
Format: disable
|
|
|
|
cm206= [HW,CD]
|
|
Format: { auto | [<io>,][<irq>] }
|
|
|
|
com20020= [HW,NET] ARCnet - COM20020 chipset
|
|
Format: <io>[,<irq>[,<nodeID>[,<backplane>[,<ckp>[,<timeout>]]]]]
|
|
|
|
com90io= [HW,NET] ARCnet - COM90xx chipset (IO-mapped buffers)
|
|
Format: <io>[,<irq>]
|
|
|
|
com90xx= [HW,NET] ARCnet - COM90xx chipset (memory-mapped buffers)
|
|
Format: <io>[,<irq>[,<memstart>]]
|
|
|
|
condev= [HW,S390] console device
|
|
conmode=
|
|
|
|
console= [KNL] Output console device and options.
|
|
|
|
tty<n> Use the virtual console device <n>.
|
|
|
|
ttyS<n>[,options]
|
|
Use the specified serial port. The options are of
|
|
the form "bbbbpn", where "bbbb" is the baud rate,
|
|
"p" is parity ("n", "o", or "e"), and "n" is bits.
|
|
Default is "9600n8".
|
|
|
|
See also Documentation/serial-console.txt.
|
|
|
|
uart,io,<addr>[,options]
|
|
uart,mmio,<addr>[,options]
|
|
Start an early, polled-mode console on the 8250/16550
|
|
UART at the specified I/O port or MMIO address,
|
|
switching to the matching ttyS device later. The
|
|
options are the same as for ttyS, above.
|
|
|
|
cpcihp_generic= [HW,PCI] Generic port I/O CompactPCI driver
|
|
Format: <first_slot>,<last_slot>,<port>,<enum_bit>[,<debug>]
|
|
|
|
cpia_pp= [HW,PPT]
|
|
Format: { parport<nr> | auto | none }
|
|
|
|
cs4232= [HW,OSS]
|
|
Format: <io>,<irq>,<dma>,<dma2>,<mpuio>,<mpuirq>
|
|
|
|
cs89x0_dma= [HW,NET]
|
|
Format: <dma>
|
|
|
|
cs89x0_media= [HW,NET]
|
|
Format: { rj45 | aui | bnc }
|
|
|
|
cyclades= [HW,SERIAL] Cyclades multi-serial port adapter.
|
|
|
|
dasd= [HW,NET]
|
|
See header of drivers/s390/block/dasd_devmap.c.
|
|
|
|
db9.dev[2|3]= [HW,JOY] Multisystem joystick support via parallel port
|
|
(one device per port)
|
|
Format: <port#>,<type>
|
|
See also Documentation/input/joystick-parport.txt
|
|
|
|
debug [KNL] Enable kernel debugging (events log level).
|
|
|
|
decnet= [HW,NET]
|
|
Format: <area>[,<node>]
|
|
See also Documentation/networking/decnet.txt.
|
|
|
|
devfs= [DEVFS]
|
|
See Documentation/filesystems/devfs/boot-options.
|
|
|
|
dhash_entries= [KNL]
|
|
Set number of hash buckets for dentry cache.
|
|
|
|
digi= [HW,SERIAL]
|
|
IO parameters + enable/disable command.
|
|
|
|
digiepca= [HW,SERIAL]
|
|
See drivers/char/README.epca and
|
|
Documentation/digiepca.txt.
|
|
|
|
dmascc= [HW,AX25,SERIAL] AX.25 Z80SCC driver with DMA
|
|
support available.
|
|
Format: <io_dev0>[,<io_dev1>[,..<io_dev32>]]
|
|
|
|
dmasound= [HW,OSS] Sound subsystem buffers
|
|
|
|
dscc4.setup= [NET]
|
|
|
|
dtc3181e= [HW,SCSI]
|
|
|
|
earlyprintk= [IA-32, X86-64]
|
|
earlyprintk=vga
|
|
earlyprintk=serial[,ttySn[,baudrate]]
|
|
|
|
Append ,keep to not disable it when the real console
|
|
takes over.
|
|
|
|
Only vga or serial at a time, not both.
|
|
|
|
Currently only ttyS0 and ttyS1 are supported.
|
|
|
|
Interaction with the standard serial driver is not
|
|
very good.
|
|
|
|
The VGA output is eventually overwritten by the real
|
|
console.
|
|
|
|
eata= [HW,SCSI]
|
|
|
|
eda= [HW,PS2]
|
|
|
|
edb= [HW,PS2]
|
|
|
|
edd= [EDD]
|
|
Format: {"of[f]" | "sk[ipmbr]"}
|
|
See comment in arch/i386/boot/edd.S
|
|
|
|
eicon= [HW,ISDN]
|
|
Format: <id>,<membase>,<irq>
|
|
|
|
eisa_irq_edge= [PARISC,HW]
|
|
See header of drivers/parisc/eisa.c.
|
|
|
|
elanfreq= [IA-32]
|
|
See comment before function elanfreq_setup() in
|
|
arch/i386/kernel/cpu/cpufreq/elanfreq.c.
|
|
|
|
elevator= [IOSCHED]
|
|
Format: {"as"|"cfq"|"deadline"|"noop"}
|
|
See Documentation/block/as-iosched.txt
|
|
and Documentation/block/deadline-iosched.txt for details.
|
|
|
|
enforcing [SELINUX] Set initial enforcing status.
|
|
Format: {"0" | "1"}
|
|
See security/selinux/Kconfig help text.
|
|
0 -- permissive (log only, no denials).
|
|
1 -- enforcing (deny and log).
|
|
Default value is 0.
|
|
Value can be changed at runtime via /selinux/enforce.
|
|
|
|
es1370= [HW,OSS]
|
|
Format: <lineout>[,<micbias>]
|
|
See also header of sound/oss/es1370.c.
|
|
|
|
es1371= [HW,OSS]
|
|
Format: <spdif>,[<nomix>,[<amplifier>]]
|
|
See also header of sound/oss/es1371.c.
|
|
|
|
ether= [HW,NET] Ethernet cards parameters
|
|
This option is obsoleted by the "netdev=" option, which
|
|
has equivalent usage. See its documentation for details.
|
|
|
|
eurwdt= [HW,WDT] Eurotech CPU-1220/1410 onboard watchdog.
|
|
Format: <io>[,<irq>]
|
|
|
|
fd_mcs= [HW,SCSI]
|
|
See header of drivers/scsi/fd_mcs.c.
|
|
|
|
fdomain= [HW,SCSI]
|
|
See header of drivers/scsi/fdomain.c.
|
|
|
|
floppy= [HW]
|
|
See Documentation/floppy.txt.
|
|
|
|
ftape= [HW] Floppy Tape subsystem debugging options.
|
|
See Documentation/ftape.txt.
|
|
|
|
gamecon.map[2|3]=
|
|
[HW,JOY] Multisystem joystick and NES/SNES/PSX pad
|
|
support via parallel port (up to 5 devices per port)
|
|
Format: <port#>,<pad1>,<pad2>,<pad3>,<pad4>,<pad5>
|
|
See also Documentation/input/joystick-parport.txt
|
|
|
|
gamma= [HW,DRM]
|
|
|
|
gdth= [HW,SCSI]
|
|
See header of drivers/scsi/gdth.c.
|
|
|
|
gpt [EFI] Forces disk with valid GPT signature but
|
|
invalid Protective MBR to be treated as GPT.
|
|
|
|
gscd= [HW,CD]
|
|
Format: <io>
|
|
|
|
gt96100eth= [NET] MIPS GT96100 Advanced Communication Controller
|
|
|
|
gus= [HW,OSS]
|
|
Format: <io>,<irq>,<dma>,<dma16>
|
|
|
|
gvp11= [HW,SCSI]
|
|
|
|
hashdist= [KNL,NUMA] Large hashes allocated during boot
|
|
are distributed across NUMA nodes. Defaults on
|
|
for IA-64, off otherwise.
|
|
|
|
hcl= [IA-64] SGI's Hardware Graph compatibility layer
|
|
|
|
hd= [EIDE] (E)IDE hard drive subsystem geometry
|
|
Format: <cyl>,<head>,<sect>
|
|
|
|
hd?= [HW] (E)IDE subsystem
|
|
hd?lun= See Documentation/ide.txt.
|
|
|
|
highmem=nn[KMG] [KNL,BOOT] forces the highmem zone to have an exact
|
|
size of <nn>. This works even on boxes that have no
|
|
highmem otherwise. This also works to reduce highmem
|
|
size on bigger boxes.
|
|
|
|
hisax= [HW,ISDN]
|
|
See Documentation/isdn/README.HiSax.
|
|
|
|
hugepages= [HW,IA-32,IA-64] Maximal number of HugeTLB pages.
|
|
|
|
noirqbalance [IA-32,SMP,KNL] Disable kernel irq balancing
|
|
|
|
i8042.direct [HW] Put keyboard port into non-translated mode
|
|
i8042.dumbkbd [HW] Pretend that controlled can only read data from
|
|
keyboard and can not control its state
|
|
(Don't attempt to blink the leds)
|
|
i8042.noaux [HW] Don't check for auxiliary (== mouse) port
|
|
i8042.nomux [HW] Don't check presence of an active multiplexing
|
|
controller
|
|
i8042.nopnp [HW] Don't use ACPIPnP / PnPBIOS to discover KBD/AUX
|
|
controllers
|
|
i8042.panicblink=
|
|
[HW] Frequency with which keyboard LEDs should blink
|
|
when kernel panics (default is 0.5 sec)
|
|
i8042.reset [HW] Reset the controller during init and cleanup
|
|
i8042.unlock [HW] Unlock (ignore) the keylock
|
|
|
|
i810= [HW,DRM]
|
|
|
|
i8k.force [HW] Activate i8k driver even if SMM BIOS signature
|
|
does not match list of supported models.
|
|
i8k.power_status
|
|
[HW] Report power status in /proc/i8k
|
|
(disabled by default)
|
|
i8k.restricted [HW] Allow controlling fans only if SYS_ADMIN
|
|
capability is set.
|
|
|
|
ibmmcascsi= [HW,MCA,SCSI] IBM MicroChannel SCSI adapter
|
|
See Documentation/mca.txt.
|
|
|
|
icn= [HW,ISDN]
|
|
Format: <io>[,<membase>[,<icn_id>[,<icn_id2>]]]
|
|
|
|
ide= [HW] (E)IDE subsystem
|
|
Format: ide=nodma or ide=doubler or ide=reverse
|
|
See Documentation/ide.txt.
|
|
|
|
ide?= [HW] (E)IDE subsystem
|
|
Format: ide?=noprobe or chipset specific parameters.
|
|
See Documentation/ide.txt.
|
|
|
|
idebus= [HW] (E)IDE subsystem - VLB/PCI bus speed
|
|
See Documentation/ide.txt.
|
|
|
|
idle= [HW]
|
|
Format: idle=poll or idle=halt
|
|
|
|
ihash_entries= [KNL]
|
|
Set number of hash buckets for inode cache.
|
|
|
|
in2000= [HW,SCSI]
|
|
See header of drivers/scsi/in2000.c.
|
|
|
|
init= [KNL]
|
|
Format: <full_path>
|
|
Run specified binary instead of /sbin/init as init
|
|
process.
|
|
|
|
initcall_debug [KNL] Trace initcalls as they are executed. Useful
|
|
for working out where the kernel is dying during
|
|
startup.
|
|
|
|
initrd= [BOOT] Specify the location of the initial ramdisk
|
|
|
|
inport.irq= [HW] Inport (ATI XL and Microsoft) busmouse driver
|
|
Format: <irq>
|
|
|
|
inttest= [IA64]
|
|
|
|
io7= [HW] IO7 for Marvel based alpha systems
|
|
See comment before marvel_specify_io7 in
|
|
arch/alpha/kernel/core_marvel.c.
|
|
|
|
ip= [IP_PNP]
|
|
See Documentation/nfsroot.txt.
|
|
|
|
ip2= [HW] Set IO/IRQ pairs for up to 4 IntelliPort boards
|
|
See comment before ip2_setup() in drivers/char/ip2.c.
|
|
|
|
ips= [HW,SCSI] Adaptec / IBM ServeRAID controller
|
|
See header of drivers/scsi/ips.c.
|
|
|
|
isapnp= [ISAPNP]
|
|
Format: <RDP>, <reset>, <pci_scan>, <verbosity>
|
|
|
|
isolcpus= [KNL,SMP] Isolate CPUs from the general scheduler.
|
|
Format: <cpu number>,...,<cpu number>
|
|
This option can be used to specify one or more CPUs
|
|
to isolate from the general SMP balancing and scheduling
|
|
algorithms. The only way to move a process onto or off
|
|
an "isolated" CPU is via the CPU affinity syscalls.
|
|
<cpu number> begins at 0 and the maximum value is
|
|
"number of CPUs in system - 1".
|
|
|
|
This option is the preferred way to isolate CPUs. The
|
|
alternative - manually setting the CPU mask of all tasks
|
|
in the system can cause problems and suboptimal load
|
|
balancer performance.
|
|
|
|
isp16= [HW,CD]
|
|
Format: <io>,<irq>,<dma>,<setup>
|
|
|
|
iucv= [HW,NET]
|
|
|
|
js= [HW,JOY] Analog joystick
|
|
See Documentation/input/joystick.txt.
|
|
|
|
keepinitrd [HW,ARM]
|
|
|
|
kstack=N [IA-32, X86-64] Print N words from the kernel stack
|
|
in oops dumps.
|
|
|
|
l2cr= [PPC]
|
|
|
|
lapic [IA-32,APIC] Enable the local APIC even if BIOS disabled it.
|
|
|
|
lasi= [HW,SCSI] PARISC LASI driver for the 53c700 chip
|
|
Format: addr:<io>,irq:<irq>
|
|
|
|
llsc*= [IA64]
|
|
See function print_params() in arch/ia64/sn/kernel/llsc4.c.
|
|
|
|
load_ramdisk= [RAM] List of ramdisks to load from floppy
|
|
See Documentation/ramdisk.txt.
|
|
|
|
lockd.udpport= [NFS]
|
|
|
|
lockd.tcpport= [NFS]
|
|
|
|
logibm.irq= [HW,MOUSE] Logitech Bus Mouse Driver
|
|
Format: <irq>
|
|
|
|
loglevel= All Kernel Messages with a loglevel smaller than the
|
|
console loglevel will be printed to the console. It can
|
|
also be changed with klogd or other programs. The
|
|
loglevels are defined as follows:
|
|
|
|
0 (KERN_EMERG) system is unusable
|
|
1 (KERN_ALERT) action must be taken immediately
|
|
2 (KERN_CRIT) critical conditions
|
|
3 (KERN_ERR) error conditions
|
|
4 (KERN_WARNING) warning conditions
|
|
5 (KERN_NOTICE) normal but significant condition
|
|
6 (KERN_INFO) informational
|
|
7 (KERN_DEBUG) debug-level messages
|
|
|
|
log_buf_len=n Sets the size of the printk ring buffer, in bytes.
|
|
Format is n, nk, nM. n must be a power of two. The
|
|
default is set in kernel config.
|
|
|
|
lp=0 [LP] Specify parallel ports to use, e.g,
|
|
lp=port[,port...] lp=none,parport0 (lp0 not configured, lp1 uses
|
|
lp=reset first parallel port). 'lp=0' disables the
|
|
lp=auto printer driver. 'lp=reset' (which can be
|
|
specified in addition to the ports) causes
|
|
attached printers to be reset. Using
|
|
lp=port1,port2,... specifies the parallel ports
|
|
to associate lp devices with, starting with
|
|
lp0. A port specification may be 'none' to skip
|
|
that lp device, or a parport name such as
|
|
'parport0'. Specifying 'lp=auto' instead of a
|
|
port specification list means that device IDs
|
|
from each port should be examined, to see if
|
|
an IEEE 1284-compliant printer is attached; if
|
|
so, the driver will manage that printer.
|
|
See also header of drivers/char/lp.c.
|
|
|
|
lpj=n [KNL]
|
|
Sets loops_per_jiffy to given constant, thus avoiding
|
|
time-consuming boot-time autodetection (up to 250 ms per
|
|
CPU). 0 enables autodetection (default). To determine
|
|
the correct value for your kernel, boot with normal
|
|
autodetection and see what value is printed. Note that
|
|
on SMP systems the preset will be applied to all CPUs,
|
|
which is likely to cause problems if your CPUs need
|
|
significantly divergent settings. An incorrect value
|
|
will cause delays in the kernel to be wrong, leading to
|
|
unpredictable I/O errors and other breakage. Although
|
|
unlikely, in the extreme case this might damage your
|
|
hardware.
|
|
|
|
ltpc= [NET]
|
|
Format: <io>,<irq>,<dma>
|
|
|
|
mac5380= [HW,SCSI]
|
|
Format: <can_queue>,<cmd_per_lun>,<sg_tablesize>,<hostid>,<use_tags>
|
|
|
|
mac53c9x= [HW,SCSI]
|
|
Format: <num_esps>,<disconnect>,<nosync>,<can_queue>,<cmd_per_lun>,<sg_tablesize>,<hostid>,<use_tags>
|
|
|
|
machvec= [IA64]
|
|
Force the use of a particular machine-vector (machvec) in a generic
|
|
kernel. Example: machvec=hpzx1_swiotlb
|
|
|
|
mad16= [HW,OSS]
|
|
Format: <io>,<irq>,<dma>,<dma16>,<mpu_io>,<mpu_irq>,<joystick>
|
|
|
|
maui= [HW,OSS]
|
|
Format: <io>,<irq>
|
|
|
|
max_loop= [LOOP] Maximum number of loopback devices that can
|
|
be mounted
|
|
Format: <1-256>
|
|
|
|
maxcpus= [SMP] Maximum number of processors that an SMP kernel
|
|
should make use of
|
|
|
|
max_luns= [SCSI] Maximum number of LUNs to probe
|
|
Should be between 1 and 2^32-1.
|
|
|
|
max_report_luns=
|
|
[SCSI] Maximum number of LUNs received
|
|
Should be between 1 and 16384.
|
|
|
|
mca-pentium [BUGS=IA-32]
|
|
|
|
mcatest= [IA-64]
|
|
|
|
mcd= [HW,CD]
|
|
Format: <port>,<irq>,<mitsumi_bug_93_wait>
|
|
|
|
mcdx= [HW,CD]
|
|
|
|
mce [IA-32] Machine Check Exception
|
|
|
|
md= [HW] RAID subsystems devices and level
|
|
See Documentation/md.txt.
|
|
|
|
mdacon= [MDA]
|
|
Format: <first>,<last>
|
|
Specifies range of consoles to be captured by the MDA.
|
|
|
|
mem=nn[KMG] [KNL,BOOT] Force usage of a specific amount of memory
|
|
Amount of memory to be used when the kernel is not able
|
|
to see the whole system memory or for test.
|
|
[IA-32] Use together with memmap= to avoid physical
|
|
address space collisions. Without memmap= PCI devices
|
|
could be placed at addresses belonging to unused RAM.
|
|
|
|
mem=nopentium [BUGS=IA-32] Disable usage of 4MB pages for kernel
|
|
memory.
|
|
|
|
memmap=exactmap [KNL,IA-32] Enable setting of an exact
|
|
E820 memory map, as specified by the user.
|
|
Such memmap=exactmap lines can be constructed based on
|
|
BIOS output or other requirements. See the memmap=nn@ss
|
|
option description.
|
|
|
|
memmap=nn[KMG]@ss[KMG]
|
|
[KNL] Force usage of a specific region of memory
|
|
Region of memory to be used, from ss to ss+nn.
|
|
|
|
memmap=nn[KMG]#ss[KMG]
|
|
[KNL,ACPI] Mark specific memory as ACPI data.
|
|
Region of memory to be used, from ss to ss+nn.
|
|
|
|
memmap=nn[KMG]$ss[KMG]
|
|
[KNL,ACPI] Mark specific memory as reserved.
|
|
Region of memory to be used, from ss to ss+nn.
|
|
|
|
meye.*= [HW] Set MotionEye Camera parameters
|
|
See Documentation/video4linux/meye.txt.
|
|
|
|
mga= [HW,DRM]
|
|
|
|
mousedev.tap_time=
|
|
[MOUSE] Maximum time between finger touching and
|
|
leaving touchpad surface for touch to be considered
|
|
a tap and be reported as a left button click (for
|
|
touchpads working in absolute mode only).
|
|
Format: <msecs>
|
|
mousedev.xres= [MOUSE] Horizontal screen resolution, used for devices
|
|
reporting absolute coordinates, such as tablets
|
|
mousedev.yres= [MOUSE] Vertical screen resolution, used for devices
|
|
reporting absolute coordinates, such as tablets
|
|
|
|
mpu401= [HW,OSS]
|
|
Format: <io>,<irq>
|
|
|
|
MTD_Partition= [MTD]
|
|
Format: <name>,<region-number>,<size>,<offset>
|
|
|
|
MTD_Region= [MTD]
|
|
Format: <name>,<region-number>[,<base>,<size>,<buswidth>,<altbuswidth>]
|
|
|
|
mtdparts= [MTD]
|
|
See drivers/mtd/cmdline.c.
|
|
|
|
mtouchusb.raw_coordinates=
|
|
[HW] Make the MicroTouch USB driver use raw coordinates ('y', default)
|
|
or cooked coordinates ('n')
|
|
|
|
n2= [NET] SDL Inc. RISCom/N2 synchronous serial card
|
|
|
|
NCR_D700= [HW,SCSI]
|
|
See header of drivers/scsi/NCR_D700.c.
|
|
|
|
ncr5380= [HW,SCSI]
|
|
|
|
ncr53c400= [HW,SCSI]
|
|
|
|
ncr53c400a= [HW,SCSI]
|
|
|
|
ncr53c406a= [HW,SCSI]
|
|
|
|
ncr53c8xx= [HW,SCSI]
|
|
|
|
netdev= [NET] Network devices parameters
|
|
Format: <irq>,<io>,<mem_start>,<mem_end>,<name>
|
|
Note that mem_start is often overloaded to mean
|
|
something different and driver-specific.
|
|
|
|
nfsaddrs= [NFS]
|
|
See Documentation/nfsroot.txt.
|
|
|
|
nfsroot= [NFS] nfs root filesystem for disk-less boxes.
|
|
See Documentation/nfsroot.txt.
|
|
|
|
nmi_watchdog= [KNL,BUGS=IA-32] Debugging features for SMP kernels
|
|
|
|
no387 [BUGS=IA-32] Tells the kernel to use the 387 maths
|
|
emulation library even if a 387 maths coprocessor
|
|
is present.
|
|
|
|
noalign [KNL,ARM]
|
|
|
|
noapic [SMP,APIC] Tells the kernel to not make use of any
|
|
IOAPICs that may be present in the system.
|
|
|
|
noasync [HW,M68K] Disables async and sync negotiation for
|
|
all devices.
|
|
|
|
nobats [PPC] Do not use BATs for mapping kernel lowmem
|
|
on "Classic" PPC cores.
|
|
|
|
nocache [ARM]
|
|
|
|
nodisconnect [HW,SCSI,M68K] Disables SCSI disconnects.
|
|
|
|
noexec [IA-64]
|
|
|
|
noexec [IA-32, X86-64]
|
|
noexec=on: enable non-executable mappings (default)
|
|
noexec=off: disable nn-executable mappings
|
|
|
|
nofxsr [BUGS=IA-32]
|
|
|
|
nohlt [BUGS=ARM]
|
|
|
|
no-hlt [BUGS=IA-32] Tells the kernel that the hlt
|
|
instruction doesn't work correctly and not to
|
|
use it.
|
|
|
|
nohalt [IA-64] Tells the kernel not to use the power saving
|
|
function PAL_HALT_LIGHT when idle. This increases
|
|
power-consumption. On the positive side, it reduces
|
|
interrupt wake-up latency, which may improve performance
|
|
in certain environments such as networked servers or
|
|
real-time systems.
|
|
|
|
noirqdebug [IA-32] Disables the code which attempts to detect and
|
|
disable unhandled interrupt sources.
|
|
|
|
noisapnp [ISAPNP] Disables ISA PnP code.
|
|
|
|
noinitrd [RAM] Tells the kernel not to load any configured
|
|
initial RAM disk.
|
|
|
|
nointroute [IA-64]
|
|
|
|
nolapic [IA-32,APIC] Do not enable or use the local APIC.
|
|
|
|
noltlbs [PPC] Do not use large page/tlb entries for kernel
|
|
lowmem mapping on PPC40x.
|
|
|
|
nomce [IA-32] Machine Check Exception
|
|
|
|
noresidual [PPC] Don't use residual data on PReP machines.
|
|
|
|
noresume [SWSUSP] Disables resume and restore original swap space.
|
|
|
|
no-scroll [VGA] Disables scrollback.
|
|
This is required for the Braillex ib80-piezo Braille
|
|
reader made by F.H. Papenmeier (Germany).
|
|
|
|
nosbagart [IA-64]
|
|
|
|
nosmp [SMP] Tells an SMP kernel to act as a UP kernel.
|
|
|
|
nosync [HW,M68K] Disables sync negotiation for all devices.
|
|
|
|
notsc [BUGS=IA-32] Disable Time Stamp Counter
|
|
|
|
nousb [USB] Disable the USB subsystem
|
|
|
|
nowb [ARM]
|
|
|
|
opl3= [HW,OSS]
|
|
Format: <io>
|
|
|
|
opl3sa= [HW,OSS]
|
|
Format: <io>,<irq>,<dma>,<dma2>,<mpu_io>,<mpu_irq>
|
|
|
|
opl3sa2= [HW,OSS]
|
|
Format: <io>,<irq>,<dma>,<dma2>,<mss_io>,<mpu_io>,<ymode>,<loopback>[,<isapnp>,<multiple]
|
|
|
|
oprofile.timer= [HW]
|
|
Use timer interrupt instead of performance counters
|
|
|
|
optcd= [HW,CD]
|
|
Format: <io>
|
|
|
|
osst= [HW,SCSI] SCSI Tape Driver
|
|
Format: <buffer_size>,<write_threshold>
|
|
See also Documentation/scsi/st.txt.
|
|
|
|
panic= [KNL] Kernel behaviour on panic
|
|
Format: <timeout>
|
|
|
|
parkbd.port= [HW] Parallel port number the keyboard adapter is
|
|
connected to, default is 0.
|
|
Format: <parport#>
|
|
parkbd.mode= [HW] Parallel port keyboard adapter mode of operation,
|
|
0 for XT, 1 for AT (default is AT).
|
|
Format: <mode>
|
|
|
|
parport=0 [HW,PPT] Specify parallel ports. 0 disables.
|
|
parport=auto Use 'auto' to force the driver to use
|
|
parport=0xBBB[,IRQ[,DMA]] any IRQ/DMA settings detected (the
|
|
default is to ignore detected IRQ/DMA
|
|
settings because of possible
|
|
conflicts). You can specify the base
|
|
address, IRQ, and DMA settings; IRQ and
|
|
DMA should be numbers, or 'auto' (for
|
|
using detected settings on that
|
|
particular port), or 'nofifo' (to avoid
|
|
using a FIFO even if it is detected).
|
|
Parallel ports are assigned in the
|
|
order they are specified on the command
|
|
line, starting with parport0.
|
|
|
|
parport_init_mode=
|
|
[HW,PPT] Configure VIA parallel port to
|
|
operate in specific mode. This is
|
|
necessary on Pegasos computer where
|
|
firmware has no options for setting up
|
|
parallel port mode and sets it to
|
|
spp. Currently this function knows
|
|
686a and 8231 chips.
|
|
Format: [spp|ps2|epp|ecp|ecpepp]
|
|
|
|
pas2= [HW,OSS]
|
|
Format: <io>,<irq>,<dma>,<dma16>,<sb_io>,<sb_irq>,<sb_dma>,<sb_dma16>
|
|
|
|
pas16= [HW,SCSI]
|
|
See header of drivers/scsi/pas16.c.
|
|
|
|
pcbit= [HW,ISDN]
|
|
|
|
pcd. [PARIDE]
|
|
See header of drivers/block/paride/pcd.c.
|
|
See also Documentation/paride.txt.
|
|
|
|
pci=option[,option...] [PCI] various PCI subsystem options:
|
|
off [IA-32] don't probe for the PCI bus
|
|
bios [IA-32] force use of PCI BIOS, don't access
|
|
the hardware directly. Use this if your machine
|
|
has a non-standard PCI host bridge.
|
|
nobios [IA-32] disallow use of PCI BIOS, only direct
|
|
hardware access methods are allowed. Use this
|
|
if you experience crashes upon bootup and you
|
|
suspect they are caused by the BIOS.
|
|
conf1 [IA-32] Force use of PCI Configuration Mechanism 1.
|
|
conf2 [IA-32] Force use of PCI Configuration Mechanism 2.
|
|
nosort [IA-32] Don't sort PCI devices according to
|
|
order given by the PCI BIOS. This sorting is done
|
|
to get a device order compatible with older kernels.
|
|
biosirq [IA-32] Use PCI BIOS calls to get the interrupt
|
|
routing table. These calls are known to be buggy
|
|
on several machines and they hang the machine when used,
|
|
but on other computers it's the only way to get the
|
|
interrupt routing table. Try this option if the kernel
|
|
is unable to allocate IRQs or discover secondary PCI
|
|
buses on your motherboard.
|
|
rom [IA-32] Assign address space to expansion ROMs.
|
|
Use with caution as certain devices share address
|
|
decoders between ROMs and other resources.
|
|
irqmask=0xMMMM [IA-32] Set a bit mask of IRQs allowed to be assigned
|
|
automatically to PCI devices. You can make the kernel
|
|
exclude IRQs of your ISA cards this way.
|
|
lastbus=N [IA-32] Scan all buses till bus #N. Can be useful
|
|
if the kernel is unable to find your secondary buses
|
|
and you want to tell it explicitly which ones they are.
|
|
assign-busses [IA-32] Always assign all PCI bus
|
|
numbers ourselves, overriding
|
|
whatever the firmware may have
|
|
done.
|
|
usepirqmask [IA-32] Honor the possible IRQ mask
|
|
stored in the BIOS $PIR table. This is
|
|
needed on some systems with broken
|
|
BIOSes, notably some HP Pavilion N5400
|
|
and Omnibook XE3 notebooks. This will
|
|
have no effect if ACPI IRQ routing is
|
|
enabled.
|
|
noacpi [IA-32] Do not use ACPI for IRQ routing
|
|
or for PCI scanning.
|
|
routeirq Do IRQ routing for all PCI devices.
|
|
This is normally done in pci_enable_device(),
|
|
so this option is a temporary workaround
|
|
for broken drivers that don't call it.
|
|
|
|
firmware [ARM] Do not re-enumerate the bus but
|
|
instead just use the configuration
|
|
from the bootloader. This is currently
|
|
used on IXP2000 systems where the
|
|
bus has to be configured a certain way
|
|
for adjunct CPUs.
|
|
|
|
pcmv= [HW,PCMCIA] BadgePAD 4
|
|
|
|
pd. [PARIDE]
|
|
See Documentation/paride.txt.
|
|
|
|
pdcchassis= [PARISC,HW] Disable/Enable PDC Chassis Status codes at
|
|
boot time.
|
|
Format: { 0 | 1 }
|
|
See arch/parisc/kernel/pdc_chassis.c
|
|
|
|
pf. [PARIDE]
|
|
See Documentation/paride.txt.
|
|
|
|
pg. [PARIDE]
|
|
See Documentation/paride.txt.
|
|
|
|
pirq= [SMP,APIC] Manual mp-table setup
|
|
See Documentation/i386/IO-APIC.txt.
|
|
|
|
plip= [PPT,NET] Parallel port network link
|
|
Format: { parport<nr> | timid | 0 }
|
|
See also Documentation/parport.txt.
|
|
|
|
pnpacpi= [ACPI]
|
|
{ off }
|
|
|
|
pnpbios= [ISAPNP]
|
|
{ on | off | curr | res | no-curr | no-res }
|
|
|
|
pnp_reserve_irq=
|
|
[ISAPNP] Exclude IRQs for the autoconfiguration
|
|
|
|
pnp_reserve_dma=
|
|
[ISAPNP] Exclude DMAs for the autoconfiguration
|
|
|
|
pnp_reserve_io= [ISAPNP] Exclude I/O ports for the autoconfiguration
|
|
Ranges are in pairs (I/O port base and size).
|
|
|
|
pnp_reserve_mem=
|
|
[ISAPNP] Exclude memory regions for the autoconfiguration
|
|
Ranges are in pairs (memory base and size).
|
|
|
|
profile= [KNL] Enable kernel profiling via /proc/profile
|
|
{ schedule | <number> }
|
|
(param: schedule - profile schedule points}
|
|
(param: profile step/bucket size as a power of 2 for
|
|
statistical time based profiling)
|
|
|
|
processor.max_cstate= [HW, ACPI]
|
|
Limit processor to maximum C-state
|
|
max_cstate=9 overrides any DMI blacklist limit.
|
|
|
|
prompt_ramdisk= [RAM] List of RAM disks to prompt for floppy disk
|
|
before loading.
|
|
See Documentation/ramdisk.txt.
|
|
|
|
psmouse.proto= [HW,MOUSE] Highest PS2 mouse protocol extension to
|
|
probe for (bare|imps|exps).
|
|
psmouse.rate= [HW,MOUSE] Set desired mouse report rate, in reports
|
|
per second.
|
|
psmouse.resetafter=
|
|
[HW,MOUSE] Try to reset the device after so many bad packets
|
|
(0 = never).
|
|
psmouse.resolution=
|
|
[HW,MOUSE] Set desired mouse resolution, in dpi.
|
|
psmouse.smartscroll=
|
|
[HW,MOUSE] Controls Logitech smartscroll autorepeat,
|
|
0 = disabled, 1 = enabled (default).
|
|
|
|
pss= [HW,OSS] Personal Sound System (ECHO ESC614)
|
|
Format: <io>,<mss_io>,<mss_irq>,<mss_dma>,<mpu_io>,<mpu_irq>
|
|
|
|
pt. [PARIDE]
|
|
See Documentation/paride.txt.
|
|
|
|
quiet= [KNL] Disable log messages
|
|
|
|
r128= [HW,DRM]
|
|
|
|
raid= [HW,RAID]
|
|
See Documentation/md.txt.
|
|
|
|
ramdisk= [RAM] Sizes of RAM disks in kilobytes [deprecated]
|
|
See Documentation/ramdisk.txt.
|
|
|
|
ramdisk_blocksize=
|
|
[RAM]
|
|
See Documentation/ramdisk.txt.
|
|
|
|
ramdisk_size= [RAM] Sizes of RAM disks in kilobytes
|
|
New name for the ramdisk parameter.
|
|
See Documentation/ramdisk.txt.
|
|
|
|
reboot= [BUGS=IA-32,BUGS=ARM,BUGS=IA-64] Rebooting mode
|
|
Format: <reboot_mode>[,<reboot_mode2>[,...]]
|
|
See arch/*/kernel/reboot.c.
|
|
|
|
reserve= [KNL,BUGS] Force the kernel to ignore some iomem area
|
|
|
|
resume= [SWSUSP] Specify the partition device for software suspension
|
|
|
|
rhash_entries= [KNL,NET]
|
|
Set number of hash buckets for route cache
|
|
|
|
riscom8= [HW,SERIAL]
|
|
Format: <io_board1>[,<io_board2>[,...<io_boardN>]]
|
|
|
|
ro [KNL] Mount root device read-only on boot
|
|
|
|
root= [KNL] Root filesystem
|
|
|
|
rootdelay= [KNL] Delay (in seconds) to pause before attempting to
|
|
mount the root filesystem
|
|
|
|
rootflags= [KNL] Set root filesystem mount option string
|
|
|
|
rootfstype= [KNL] Set root filesystem type
|
|
|
|
rw [KNL] Mount root device read-write on boot
|
|
|
|
S [KNL] Run init in single mode
|
|
|
|
sa1100ir [NET]
|
|
See drivers/net/irda/sa1100_ir.c.
|
|
|
|
sb= [HW,OSS]
|
|
Format: <io>,<irq>,<dma>,<dma2>
|
|
|
|
sbni= [NET] Granch SBNI12 leased line adapter
|
|
|
|
sbpcd= [HW,CD] Soundblaster CD adapter
|
|
Format: <io>,<type>
|
|
See a comment before function sbpcd_setup() in
|
|
drivers/cdrom/sbpcd.c.
|
|
|
|
sc1200wdt= [HW,WDT] SC1200 WDT (watchdog) driver
|
|
Format: <io>[,<timeout>[,<isapnp>]]
|
|
|
|
scsi_debug_*= [SCSI]
|
|
See drivers/scsi/scsi_debug.c.
|
|
|
|
scsi_default_dev_flags=
|
|
[SCSI] SCSI default device flags
|
|
Format: <integer>
|
|
|
|
scsi_dev_flags= [SCSI] Black/white list entry for vendor and model
|
|
Format: <vendor>:<model>:<flags>
|
|
(flags are integer value)
|
|
|
|
scsi_logging= [SCSI]
|
|
|
|
selinux [SELINUX] Disable or enable SELinux at boot time.
|
|
Format: { "0" | "1" }
|
|
See security/selinux/Kconfig help text.
|
|
0 -- disable.
|
|
1 -- enable.
|
|
Default value is set via kernel config option.
|
|
If enabled at boot time, /selinux/disable can be used
|
|
later to disable prior to initial policy load.
|
|
|
|
serialnumber [BUGS=IA-32]
|
|
|
|
sg_def_reserved_size=
|
|
[SCSI]
|
|
|
|
sgalaxy= [HW,OSS]
|
|
Format: <io>,<irq>,<dma>,<dma2>,<sgbase>
|
|
|
|
shapers= [NET]
|
|
Maximal number of shapers.
|
|
|
|
sim710= [SCSI,HW]
|
|
See header of drivers/scsi/sim710.c.
|
|
|
|
simeth= [IA-64]
|
|
simscsi=
|
|
|
|
sjcd= [HW,CD]
|
|
Format: <io>,<irq>,<dma>
|
|
See header of drivers/cdrom/sjcd.c.
|
|
|
|
slram= [HW,MTD]
|
|
|
|
smart2= [HW]
|
|
Format: <io1>[,<io2>[,...,<io8>]]
|
|
|
|
snd-ad1816a= [HW,ALSA]
|
|
|
|
snd-ad1848= [HW,ALSA]
|
|
|
|
snd-ali5451= [HW,ALSA]
|
|
|
|
snd-als100= [HW,ALSA]
|
|
|
|
snd-als4000= [HW,ALSA]
|
|
|
|
snd-azt2320= [HW,ALSA]
|
|
|
|
snd-cmi8330= [HW,ALSA]
|
|
|
|
snd-cmipci= [HW,ALSA]
|
|
|
|
snd-cs4231= [HW,ALSA]
|
|
|
|
snd-cs4232= [HW,ALSA]
|
|
|
|
snd-cs4236= [HW,ALSA]
|
|
|
|
snd-cs4281= [HW,ALSA]
|
|
|
|
snd-cs46xx= [HW,ALSA]
|
|
|
|
snd-dt019x= [HW,ALSA]
|
|
|
|
snd-dummy= [HW,ALSA]
|
|
|
|
snd-emu10k1= [HW,ALSA]
|
|
|
|
snd-ens1370= [HW,ALSA]
|
|
|
|
snd-ens1371= [HW,ALSA]
|
|
|
|
snd-es968= [HW,ALSA]
|
|
|
|
snd-es1688= [HW,ALSA]
|
|
|
|
snd-es18xx= [HW,ALSA]
|
|
|
|
snd-es1938= [HW,ALSA]
|
|
|
|
snd-es1968= [HW,ALSA]
|
|
|
|
snd-fm801= [HW,ALSA]
|
|
|
|
snd-gusclassic= [HW,ALSA]
|
|
|
|
snd-gusextreme= [HW,ALSA]
|
|
|
|
snd-gusmax= [HW,ALSA]
|
|
|
|
snd-hdsp= [HW,ALSA]
|
|
|
|
snd-ice1712= [HW,ALSA]
|
|
|
|
snd-intel8x0= [HW,ALSA]
|
|
|
|
snd-interwave= [HW,ALSA]
|
|
|
|
snd-interwave-stb=
|
|
[HW,ALSA]
|
|
|
|
snd-korg1212= [HW,ALSA]
|
|
|
|
snd-maestro3= [HW,ALSA]
|
|
|
|
snd-mpu401= [HW,ALSA]
|
|
|
|
snd-mtpav= [HW,ALSA]
|
|
|
|
snd-nm256= [HW,ALSA]
|
|
|
|
snd-opl3sa2= [HW,ALSA]
|
|
|
|
snd-opti92x-ad1848=
|
|
[HW,ALSA]
|
|
|
|
snd-opti92x-cs4231=
|
|
[HW,ALSA]
|
|
|
|
snd-opti93x= [HW,ALSA]
|
|
|
|
snd-pmac= [HW,ALSA]
|
|
|
|
snd-rme32= [HW,ALSA]
|
|
|
|
snd-rme96= [HW,ALSA]
|
|
|
|
snd-rme9652= [HW,ALSA]
|
|
|
|
snd-sb8= [HW,ALSA]
|
|
|
|
snd-sb16= [HW,ALSA]
|
|
|
|
snd-sbawe= [HW,ALSA]
|
|
|
|
snd-serial= [HW,ALSA]
|
|
|
|
snd-sgalaxy= [HW,ALSA]
|
|
|
|
snd-sonicvibes= [HW,ALSA]
|
|
|
|
snd-sun-amd7930=
|
|
[HW,ALSA]
|
|
|
|
snd-sun-cs4231= [HW,ALSA]
|
|
|
|
snd-trident= [HW,ALSA]
|
|
|
|
snd-usb-audio= [HW,ALSA,USB]
|
|
|
|
snd-via82xx= [HW,ALSA]
|
|
|
|
snd-virmidi= [HW,ALSA]
|
|
|
|
snd-wavefront= [HW,ALSA]
|
|
|
|
snd-ymfpci= [HW,ALSA]
|
|
|
|
sonicvibes= [HW,OSS]
|
|
Format: <reverb>
|
|
|
|
sonycd535= [HW,CD]
|
|
Format: <io>[,<irq>]
|
|
|
|
sonypi.*= [HW] Sony Programmable I/O Control Device driver
|
|
See Documentation/sonypi.txt
|
|
|
|
specialix= [HW,SERIAL] Specialix multi-serial port adapter
|
|
See Documentation/specialix.txt.
|
|
|
|
spia_io_base= [HW,MTD]
|
|
spia_fio_base=
|
|
spia_pedr=
|
|
spia_peddr=
|
|
|
|
sscape= [HW,OSS]
|
|
Format: <io>,<irq>,<dma>,<mpu_io>,<mpu_irq>
|
|
|
|
st= [HW,SCSI] SCSI tape parameters (buffers, etc.)
|
|
See Documentation/scsi/st.txt.
|
|
|
|
st0x= [HW,SCSI]
|
|
See header of drivers/scsi/seagate.c.
|
|
|
|
sti= [PARISC,HW]
|
|
Format: <num>
|
|
Set the STI (builtin display/keyboard on the HP-PARISC
|
|
machines) console (graphic card) which should be used
|
|
as the initial boot-console.
|
|
See also comment in drivers/video/console/sticore.c.
|
|
|
|
sti_font= [HW]
|
|
See comment in drivers/video/console/sticore.c.
|
|
|
|
stifb= [HW]
|
|
Format: bpp:<bpp1>[:<bpp2>[:<bpp3>...]]
|
|
|
|
stram_swap= [HW,M68k]
|
|
|
|
swiotlb= [IA-64] Number of I/O TLB slabs
|
|
|
|
switches= [HW,M68k]
|
|
|
|
sym53c416= [HW,SCSI]
|
|
See header of drivers/scsi/sym53c416.c.
|
|
|
|
t128= [HW,SCSI]
|
|
See header of drivers/scsi/t128.c.
|
|
|
|
tdfx= [HW,DRM]
|
|
|
|
thash_entries= [KNL,NET]
|
|
Set number of hash buckets for TCP connection
|
|
|
|
time Show timing data prefixed to each printk message line
|
|
|
|
tipar.timeout= [HW,PPT]
|
|
Set communications timeout in tenths of a second
|
|
(default 15).
|
|
|
|
tipar.delay= [HW,PPT]
|
|
Set inter-bit delay in microseconds (default 10).
|
|
|
|
tmc8xx= [HW,SCSI]
|
|
See header of drivers/scsi/seagate.c.
|
|
|
|
tmscsim= [HW,SCSI]
|
|
See comment before function dc390_setup() in
|
|
drivers/scsi/tmscsim.c.
|
|
|
|
tp720= [HW,PS2]
|
|
|
|
trix= [HW,OSS] MediaTrix AudioTrix Pro
|
|
Format: <io>,<irq>,<dma>,<dma2>,<sb_io>,<sb_irq>,<sb_dma>,<mpu_io>,<mpu_irq>
|
|
|
|
tsdev.xres= [TS] Horizontal screen resolution.
|
|
tsdev.yres= [TS] Vertical screen resolution.
|
|
|
|
turbografx.map[2|3]=
|
|
[HW,JOY] TurboGraFX parallel port interface
|
|
Format: <port#>,<js1>,<js2>,<js3>,<js4>,<js5>,<js6>,<js7>
|
|
See also Documentation/input/joystick-parport.txt
|
|
|
|
u14-34f= [HW,SCSI] UltraStor 14F/34F SCSI host adapter
|
|
See header of drivers/scsi/u14-34f.c.
|
|
|
|
uart401= [HW,OSS]
|
|
Format: <io>,<irq>
|
|
|
|
uart6850= [HW,OSS]
|
|
Format: <io>,<irq>
|
|
|
|
usb-handoff [HW] Enable early USB BIOS -> OS handoff
|
|
|
|
usbhid.mousepoll=
|
|
[USBHID] The interval which mice are to be polled at.
|
|
|
|
video= [FB] Frame buffer configuration
|
|
See Documentation/fb/modedb.txt.
|
|
|
|
vga= [BOOT,IA-32] Select a particular video mode
|
|
See Documentation/i386/boot.txt and Documentation/svga.txt.
|
|
Use vga=ask for menu.
|
|
This is actually a boot loader parameter; the value is
|
|
passed to the kernel using a special protocol.
|
|
|
|
vmalloc=nn[KMG] [KNL,BOOT] forces the vmalloc area to have an exact
|
|
size of <nn>. This can be used to increase the
|
|
minimum size (128MB on x86). It can also be used to
|
|
decrease the size and leave more room for directly
|
|
mapped kernel RAM.
|
|
|
|
vmhalt= [KNL,S390]
|
|
|
|
vmpoff= [KNL,S390]
|
|
|
|
waveartist= [HW,OSS]
|
|
Format: <io>,<irq>,<dma>,<dma2>
|
|
|
|
wd33c93= [HW,SCSI]
|
|
See header of drivers/scsi/wd33c93.c.
|
|
|
|
wd7000= [HW,SCSI]
|
|
See header of drivers/scsi/wd7000.c.
|
|
|
|
wdt= [WDT] Watchdog
|
|
See Documentation/watchdog/watchdog.txt.
|
|
|
|
xd= [HW,XT] Original XT pre-IDE (RLL encoded) disks.
|
|
xd_geo= See header of drivers/block/xd.c.
|
|
|
|
xirc2ps_cs= [NET,PCMCIA]
|
|
Format: <irq>,<irq_mask>,<io>,<full_duplex>,<do_sound>,<lockup_hack>[,<irq2>[,<irq3>[,<irq4>]]]
|
|
|
|
|
|
|
|
Changelog:
|
|
|
|
The last known update (for 2.4.0) - the changelog was not kept before.
|
|
2000-06-?? Mr. Unknown
|
|
|
|
Update for 2.5.49, description for most of the options introduced,
|
|
references to other documentation (C files, READMEs, ..), added S390,
|
|
PPC, SPARC, MTD, ALSA and OSS category. Minor corrections and
|
|
reformatting.
|
|
2002-11-24 Petr Baudis <pasky@ucw.cz>
|
|
Randy Dunlap <randy.dunlap@verizon.net>
|
|
|
|
TODO:
|
|
|
|
Add documentation for ALSA options.
|
|
Add more DRM drivers.
|