linux/drivers/scsi/isci/probe_roms.h
Dan Williams abec912d71 isci: refactor initialization for S3/S4
Based on an original implementation by Ed Nadolski and Artur Wojcik

In preparation for S3/S4 support refactor initialization so that
driver-load and resume-from-suspend can share the common init path of
isci_host_init().  Organize the initialization into objects that are
self-contained to the driver (initialized by isci_host_init) versus
those that have some upward registration (initialized at allocation time
asd_sas_phy, asd_sas_port, dma allocations).  The largest change is
moving the the validation of the oem and module parameters from
isci_host_init() to isci_host_alloc().

The S3/S4 approach being taken is that libsas will be tasked with
remembering the state of the domain and the lldd is free to be
forgetful.  In the case of isci we'll just re-init using a subset of the
normal driver load path.

[clean up some unused / mis-indented function definitions in host.h]

Signed-off-by: Ed Nadolski <edmund.nadolski@intel.com>
Signed-off-by: Artur Wojcik <artur.wojcik@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-05-17 12:27:12 -07:00

331 lines
10 KiB
C

/*
* This file is provided under a dual BSD/GPLv2 license. When using or
* redistributing this file, you may do so under either license.
*
* GPL LICENSE SUMMARY
*
* Copyright(c) 2008 - 2011 Intel Corporation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of version 2 of the GNU General Public License as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
* The full GNU General Public License is included in this distribution
* in the file called LICENSE.GPL.
*
* BSD LICENSE
*
* Copyright(c) 2008 - 2011 Intel Corporation. All rights reserved.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* * Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* * Neither the name of Intel Corporation nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#ifndef _ISCI_PROBE_ROMS_H_
#define _ISCI_PROBE_ROMS_H_
#ifdef __KERNEL__
#include <linux/firmware.h>
#include <linux/pci.h>
#include <linux/efi.h>
#include "isci.h"
#define SCIC_SDS_PARM_NO_SPEED 0
/* generation 1 (i.e. 1.5 Gb/s) */
#define SCIC_SDS_PARM_GEN1_SPEED 1
/* generation 2 (i.e. 3.0 Gb/s) */
#define SCIC_SDS_PARM_GEN2_SPEED 2
/* generation 3 (i.e. 6.0 Gb/s) */
#define SCIC_SDS_PARM_GEN3_SPEED 3
#define SCIC_SDS_PARM_MAX_SPEED SCIC_SDS_PARM_GEN3_SPEED
/* parameters that can be set by module parameters */
struct sci_user_parameters {
struct sci_phy_user_params {
/**
* This field specifies the NOTIFY (ENABLE SPIN UP) primitive
* insertion frequency for this phy index.
*/
u32 notify_enable_spin_up_insertion_frequency;
/**
* This method specifies the number of transmitted DWORDs within which
* to transmit a single ALIGN primitive. This value applies regardless
* of what type of device is attached or connection state. A value of
* 0 indicates that no ALIGN primitives will be inserted.
*/
u16 align_insertion_frequency;
/**
* This method specifies the number of transmitted DWORDs within which
* to transmit 2 ALIGN primitives. This applies for SAS connections
* only. A minimum value of 3 is required for this field.
*/
u16 in_connection_align_insertion_frequency;
/**
* This field indicates the maximum speed generation to be utilized
* by phys in the supplied port.
* - A value of 1 indicates generation 1 (i.e. 1.5 Gb/s).
* - A value of 2 indicates generation 2 (i.e. 3.0 Gb/s).
* - A value of 3 indicates generation 3 (i.e. 6.0 Gb/s).
*/
u8 max_speed_generation;
} phys[SCI_MAX_PHYS];
/**
* This field specifies the maximum number of direct attached devices
* that can have power supplied to them simultaneously.
*/
u8 max_concurr_spinup;
/**
* This field specifies the number of seconds to allow a phy to consume
* power before yielding to another phy.
*
*/
u8 phy_spin_up_delay_interval;
/**
* These timer values specifies how long a link will remain open with no
* activity in increments of a microsecond, it can be in increments of
* 100 microseconds if the upper most bit is set.
*
*/
u16 stp_inactivity_timeout;
u16 ssp_inactivity_timeout;
/**
* These timer values specifies how long a link will remain open in increments
* of 100 microseconds.
*
*/
u16 stp_max_occupancy_timeout;
u16 ssp_max_occupancy_timeout;
/**
* This timer value specifies how long a link will remain open with no
* outbound traffic in increments of a microsecond.
*
*/
u8 no_outbound_task_timeout;
};
#define SCIC_SDS_PARM_PHY_MASK_MIN 0x0
#define SCIC_SDS_PARM_PHY_MASK_MAX 0xF
#define MAX_CONCURRENT_DEVICE_SPIN_UP_COUNT 4
struct sci_oem_params;
int sci_oem_parameters_validate(struct sci_oem_params *oem, u8 version);
struct isci_orom;
struct isci_orom *isci_request_oprom(struct pci_dev *pdev);
struct isci_orom *isci_request_firmware(struct pci_dev *pdev, const struct firmware *fw);
struct isci_orom *isci_get_efi_var(struct pci_dev *pdev);
struct isci_oem_hdr {
u8 sig[4];
u8 rev_major;
u8 rev_minor;
u16 len;
u8 checksum;
u8 reserved1;
u16 reserved2;
} __attribute__ ((packed));
#else
#define SCI_MAX_PORTS 4
#define SCI_MAX_PHYS 4
#define SCI_MAX_CONTROLLERS 2
#endif
#define ISCI_FW_NAME "isci/isci_firmware.bin"
#define ROMSIGNATURE 0xaa55
#define ISCI_OEM_SIG "$OEM"
#define ISCI_OEM_SIG_SIZE 4
#define ISCI_ROM_SIG "ISCUOEMB"
#define ISCI_ROM_SIG_SIZE 8
#define ISCI_EFI_VENDOR_GUID \
EFI_GUID(0x193dfefa, 0xa445, 0x4302, 0x99, 0xd8, 0xef, 0x3a, 0xad, \
0x1a, 0x04, 0xc6)
#define ISCI_EFI_VAR_NAME "RstScuO"
#define ISCI_ROM_VER_1_0 0x10
#define ISCI_ROM_VER_1_1 0x11
#define ISCI_ROM_VER_1_3 0x13
#define ISCI_ROM_VER_LATEST ISCI_ROM_VER_1_3
/* Allowed PORT configuration modes APC Automatic PORT configuration mode is
* defined by the OEM configuration parameters providing no PHY_MASK parameters
* for any PORT. i.e. There are no phys assigned to any of the ports at start.
* MPC Manual PORT configuration mode is defined by the OEM configuration
* parameters providing a PHY_MASK value for any PORT. It is assumed that any
* PORT with no PHY_MASK is an invalid port and not all PHYs must be assigned.
* A PORT_PHY mask that assigns just a single PHY to a port and no other PHYs
* being assigned is sufficient to declare manual PORT configuration.
*/
enum sci_port_configuration_mode {
SCIC_PORT_MANUAL_CONFIGURATION_MODE = 0,
SCIC_PORT_AUTOMATIC_CONFIGURATION_MODE = 1
};
struct sci_bios_oem_param_block_hdr {
uint8_t signature[ISCI_ROM_SIG_SIZE];
uint16_t total_block_length;
uint8_t hdr_length;
uint8_t version;
uint8_t preboot_source;
uint8_t num_elements;
uint16_t element_length;
uint8_t reserved[8];
} __attribute__ ((packed));
struct sci_oem_params {
struct {
uint8_t mode_type;
uint8_t max_concurr_spin_up;
/*
* This bitfield indicates the OEM's desired default Tx
* Spread Spectrum Clocking (SSC) settings for SATA and SAS.
* NOTE: Default SSC Modulation Frequency is 31.5KHz.
*/
union {
struct {
/*
* NOTE: Max spread for SATA is +0 / -5000 PPM.
* Down-spreading SSC (only method allowed for SATA):
* SATA SSC Tx Disabled = 0x0
* SATA SSC Tx at +0 / -1419 PPM Spread = 0x2
* SATA SSC Tx at +0 / -2129 PPM Spread = 0x3
* SATA SSC Tx at +0 / -4257 PPM Spread = 0x6
* SATA SSC Tx at +0 / -4967 PPM Spread = 0x7
*/
uint8_t ssc_sata_tx_spread_level:4;
/*
* SAS SSC Tx Disabled = 0x0
*
* NOTE: Max spread for SAS down-spreading +0 /
* -2300 PPM
* Down-spreading SSC:
* SAS SSC Tx at +0 / -1419 PPM Spread = 0x2
* SAS SSC Tx at +0 / -2129 PPM Spread = 0x3
*
* NOTE: Max spread for SAS center-spreading +2300 /
* -2300 PPM
* Center-spreading SSC:
* SAS SSC Tx at +1064 / -1064 PPM Spread = 0x3
* SAS SSC Tx at +2129 / -2129 PPM Spread = 0x6
*/
uint8_t ssc_sas_tx_spread_level:3;
/*
* NOTE: Refer to the SSC section of the SAS 2.x
* Specification for proper setting of this field.
* For standard SAS Initiator SAS PHY operation it
* should be 0 for Down-spreading.
* SAS SSC Tx spread type:
* Down-spreading SSC = 0
* Center-spreading SSC = 1
*/
uint8_t ssc_sas_tx_type:1;
};
uint8_t do_enable_ssc;
};
/*
* This field indicates length of the SAS/SATA cable between
* host and device.
* This field is used make relationship between analog
* parameters of the phy in the silicon and length of the cable.
* Supported cable attenuation levels:
* "short"- up to 3m, "medium"-3m to 6m, and "long"- more than
* 6m.
*
* This is bit mask field:
*
* BIT: (MSB) 7 6 5 4
* ASSIGNMENT: <phy3><phy2><phy1><phy0> - Medium cable
* length assignment
* BIT: 3 2 1 0 (LSB)
* ASSIGNMENT: <phy3><phy2><phy1><phy0> - Long cable length
* assignment
*
* BITS 7-4 are set when the cable length is assigned to medium
* BITS 3-0 are set when the cable length is assigned to long
*
* The BIT positions are clear when the cable length is
* assigned to short.
*
* Setting the bits for both long and medium cable length is
* undefined.
*
* A value of 0x84 would assign
* phy3 - medium
* phy2 - long
* phy1 - short
* phy0 - short
*/
uint8_t cable_selection_mask;
} controller;
struct {
uint8_t phy_mask;
} ports[SCI_MAX_PORTS];
struct sci_phy_oem_params {
struct {
uint32_t high;
uint32_t low;
} sas_address;
uint32_t afe_tx_amp_control0;
uint32_t afe_tx_amp_control1;
uint32_t afe_tx_amp_control2;
uint32_t afe_tx_amp_control3;
} phys[SCI_MAX_PHYS];
} __attribute__ ((packed));
struct isci_orom {
struct sci_bios_oem_param_block_hdr hdr;
struct sci_oem_params ctrl[SCI_MAX_CONTROLLERS];
} __attribute__ ((packed));
#endif