mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-28 13:34:38 +08:00
1004a2977b
Use the new EBI/NAND bindings to declare NAND chips and remove old NAND nodes along the way. Note that we keep using old bindings in at91rm9200.dtsi because this SoC is not supported by the EBI driver. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Tested-by: Peter Rosin <peda@axentia.se> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
108 lines
1.7 KiB
Plaintext
108 lines
1.7 KiB
Plaintext
/*
|
|
* ethernut5.dts - Device Tree file for Ethernut 5 board
|
|
*
|
|
* Copyright (C) 2012 egnite GmbH <info@egnite.de>
|
|
*
|
|
* Licensed under GPLv2.
|
|
*/
|
|
/dts-v1/;
|
|
#include "at91sam9xe.dtsi"
|
|
|
|
/ {
|
|
model = "Ethernut 5";
|
|
compatible = "egnite,ethernut5", "atmel,at91sam9260", "atmel,at91sam9";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200 root=/dev/mtdblock0 rw rootfstype=jffs2";
|
|
};
|
|
|
|
memory {
|
|
reg = <0x20000000 0x08000000>;
|
|
};
|
|
|
|
clocks {
|
|
slow_xtal {
|
|
clock-frequency = <32768>;
|
|
};
|
|
|
|
main_xtal {
|
|
clock-frequency = <18432000>;
|
|
};
|
|
};
|
|
|
|
ahb {
|
|
apb {
|
|
dbgu: serial@fffff200 {
|
|
status = "okay";
|
|
};
|
|
|
|
usart0: serial@fffb0000 {
|
|
status = "okay";
|
|
};
|
|
|
|
usart1: serial@fffb4000 {
|
|
status = "okay";
|
|
};
|
|
|
|
macb0: ethernet@fffc4000 {
|
|
phy-mode = "rmii";
|
|
status = "okay";
|
|
};
|
|
|
|
usb1: gadget@fffa4000 {
|
|
atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
ebi: ebi@10000000 {
|
|
status = "okay";
|
|
|
|
nand_controller: nand-controller {
|
|
status = "okay";
|
|
pinctrl-0 = <&pinctrl_nand_cs>;
|
|
pinctrl-names = "default";
|
|
|
|
nand: nand@3 {
|
|
reg = <0x3 0x0 0x800000>;
|
|
cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
|
|
nand-bus-width = <8>;
|
|
nand-ecc-mode = "soft";
|
|
nand-on-flash-bbt;
|
|
label = "atmel_nand";
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
root@0 {
|
|
label = "root";
|
|
reg = <0x0 0x08000000>;
|
|
};
|
|
|
|
data@20000 {
|
|
label = "data";
|
|
reg = <0x08000000 0x38000000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
usb0: ohci@500000 {
|
|
num-ports = <2>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
i2c-gpio-0 {
|
|
status = "okay";
|
|
|
|
pcf8563@50 {
|
|
compatible = "nxp,pcf8563";
|
|
reg = <0x51>;
|
|
};
|
|
};
|
|
};
|