mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-05 18:14:07 +08:00
7de962c0c7
The cpufreq core has gone though lots of updates in recent times, but on many occasions the documentation wasn't updated along with the code. This patch tries to catchup the documentation with the code. Also add Rafael and Viresh as the contributors to the documentation. Based on a patch from Claudio Scordino. Signed-off-by: Claudio Scordino <claudio@evidence.eu.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
123 lines
4.8 KiB
Plaintext
123 lines
4.8 KiB
Plaintext
|
|
CPU frequency and voltage scaling statistics in the Linux(TM) kernel
|
|
|
|
|
|
L i n u x c p u f r e q - s t a t s d r i v e r
|
|
|
|
- information for users -
|
|
|
|
|
|
Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
|
|
|
|
Contents
|
|
1. Introduction
|
|
2. Statistics Provided (with example)
|
|
3. Configuring cpufreq-stats
|
|
|
|
|
|
1. Introduction
|
|
|
|
cpufreq-stats is a driver that provides CPU frequency statistics for each CPU.
|
|
These statistics are provided in /sysfs as a bunch of read_only interfaces. This
|
|
interface (when configured) will appear in a separate directory under cpufreq
|
|
in /sysfs (<sysfs root>/devices/system/cpu/cpuX/cpufreq/stats/) for each CPU.
|
|
Various statistics will form read_only files under this directory.
|
|
|
|
This driver is designed to be independent of any particular cpufreq_driver
|
|
that may be running on your CPU. So, it will work with any cpufreq_driver.
|
|
|
|
|
|
2. Statistics Provided (with example)
|
|
|
|
cpufreq stats provides following statistics (explained in detail below).
|
|
- time_in_state
|
|
- total_trans
|
|
- trans_table
|
|
|
|
All the statistics will be from the time the stats driver has been inserted
|
|
(or the time the stats were reset) to the time when a read of a particular
|
|
statistic is done. Obviously, stats driver will not have any information
|
|
about the frequency transitions before the stats driver insertion.
|
|
|
|
--------------------------------------------------------------------------------
|
|
<mysystem>:/sys/devices/system/cpu/cpu0/cpufreq/stats # ls -l
|
|
total 0
|
|
drwxr-xr-x 2 root root 0 May 14 16:06 .
|
|
drwxr-xr-x 3 root root 0 May 14 15:58 ..
|
|
--w------- 1 root root 4096 May 14 16:06 reset
|
|
-r--r--r-- 1 root root 4096 May 14 16:06 time_in_state
|
|
-r--r--r-- 1 root root 4096 May 14 16:06 total_trans
|
|
-r--r--r-- 1 root root 4096 May 14 16:06 trans_table
|
|
--------------------------------------------------------------------------------
|
|
|
|
- reset
|
|
Write-only attribute that can be used to reset the stat counters. This can be
|
|
useful for evaluating system behaviour under different governors without the
|
|
need for a reboot.
|
|
|
|
- time_in_state
|
|
This gives the amount of time spent in each of the frequencies supported by
|
|
this CPU. The cat output will have "<frequency> <time>" pair in each line, which
|
|
will mean this CPU spent <time> usertime units of time at <frequency>. Output
|
|
will have one line for each of the supported frequencies. usertime units here
|
|
is 10mS (similar to other time exported in /proc).
|
|
|
|
--------------------------------------------------------------------------------
|
|
<mysystem>:/sys/devices/system/cpu/cpu0/cpufreq/stats # cat time_in_state
|
|
3600000 2089
|
|
3400000 136
|
|
3200000 34
|
|
3000000 67
|
|
2800000 172488
|
|
--------------------------------------------------------------------------------
|
|
|
|
|
|
- total_trans
|
|
This gives the total number of frequency transitions on this CPU. The cat
|
|
output will have a single count which is the total number of frequency
|
|
transitions.
|
|
|
|
--------------------------------------------------------------------------------
|
|
<mysystem>:/sys/devices/system/cpu/cpu0/cpufreq/stats # cat total_trans
|
|
20
|
|
--------------------------------------------------------------------------------
|
|
|
|
- trans_table
|
|
This will give a fine grained information about all the CPU frequency
|
|
transitions. The cat output here is a two dimensional matrix, where an entry
|
|
<i,j> (row i, column j) represents the count of number of transitions from
|
|
Freq_i to Freq_j. Freq_i is in descending order with increasing rows and
|
|
Freq_j is in descending order with increasing columns. The output here also
|
|
contains the actual freq values for each row and column for better readability.
|
|
|
|
--------------------------------------------------------------------------------
|
|
<mysystem>:/sys/devices/system/cpu/cpu0/cpufreq/stats # cat trans_table
|
|
From : To
|
|
: 3600000 3400000 3200000 3000000 2800000
|
|
3600000: 0 5 0 0 0
|
|
3400000: 4 0 2 0 0
|
|
3200000: 0 1 0 2 0
|
|
3000000: 0 0 1 0 3
|
|
2800000: 0 0 0 2 0
|
|
--------------------------------------------------------------------------------
|
|
|
|
|
|
3. Configuring cpufreq-stats
|
|
|
|
To configure cpufreq-stats in your kernel
|
|
Config Main Menu
|
|
Power management options (ACPI, APM) --->
|
|
CPU Frequency scaling --->
|
|
[*] CPU Frequency scaling
|
|
[*] CPU frequency translation statistics
|
|
|
|
|
|
"CPU Frequency scaling" (CONFIG_CPU_FREQ) should be enabled to configure
|
|
cpufreq-stats.
|
|
|
|
"CPU frequency translation statistics" (CONFIG_CPU_FREQ_STAT) provides the
|
|
statistics which includes time_in_state, total_trans and trans_table.
|
|
|
|
Once this option is enabled and your CPU supports cpufrequency, you
|
|
will be able to see the CPU frequency statistics in /sysfs.
|