mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-06 02:24:14 +08:00
edead9f86c
__initconst should be placed between the variable name and equal sign for the variable to be placed in the intended section. While at it also make 'u300_clk_lookup' static as it is used only in this file. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Mike Turquette <mturquette@linaro.org>
1195 lines
38 KiB
C
1195 lines
38 KiB
C
/*
|
|
* U300 clock implementation
|
|
* Copyright (C) 2007-2012 ST-Ericsson AB
|
|
* License terms: GNU General Public License (GPL) version 2
|
|
* Author: Linus Walleij <linus.walleij@stericsson.com>
|
|
* Author: Jonas Aaberg <jonas.aberg@stericsson.com>
|
|
*/
|
|
#include <linux/clk.h>
|
|
#include <linux/clkdev.h>
|
|
#include <linux/err.h>
|
|
#include <linux/io.h>
|
|
#include <linux/clk-provider.h>
|
|
#include <linux/spinlock.h>
|
|
#include <linux/of.h>
|
|
|
|
/* APP side SYSCON registers */
|
|
/* CLK Control Register 16bit (R/W) */
|
|
#define U300_SYSCON_CCR (0x0000)
|
|
#define U300_SYSCON_CCR_I2S1_USE_VCXO (0x0040)
|
|
#define U300_SYSCON_CCR_I2S0_USE_VCXO (0x0020)
|
|
#define U300_SYSCON_CCR_TURN_VCXO_ON (0x0008)
|
|
#define U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK (0x0007)
|
|
#define U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER (0x04)
|
|
#define U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW (0x03)
|
|
#define U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE (0x02)
|
|
#define U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH (0x01)
|
|
#define U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST (0x00)
|
|
/* CLK Status Register 16bit (R/W) */
|
|
#define U300_SYSCON_CSR (0x0004)
|
|
#define U300_SYSCON_CSR_PLL208_LOCK_IND (0x0002)
|
|
#define U300_SYSCON_CSR_PLL13_LOCK_IND (0x0001)
|
|
/* Reset lines for SLOW devices 16bit (R/W) */
|
|
#define U300_SYSCON_RSR (0x0014)
|
|
#define U300_SYSCON_RSR_PPM_RESET_EN (0x0200)
|
|
#define U300_SYSCON_RSR_ACC_TMR_RESET_EN (0x0100)
|
|
#define U300_SYSCON_RSR_APP_TMR_RESET_EN (0x0080)
|
|
#define U300_SYSCON_RSR_RTC_RESET_EN (0x0040)
|
|
#define U300_SYSCON_RSR_KEYPAD_RESET_EN (0x0020)
|
|
#define U300_SYSCON_RSR_GPIO_RESET_EN (0x0010)
|
|
#define U300_SYSCON_RSR_EH_RESET_EN (0x0008)
|
|
#define U300_SYSCON_RSR_BTR_RESET_EN (0x0004)
|
|
#define U300_SYSCON_RSR_UART_RESET_EN (0x0002)
|
|
#define U300_SYSCON_RSR_SLOW_BRIDGE_RESET_EN (0x0001)
|
|
/* Reset lines for FAST devices 16bit (R/W) */
|
|
#define U300_SYSCON_RFR (0x0018)
|
|
#define U300_SYSCON_RFR_UART1_RESET_ENABLE (0x0080)
|
|
#define U300_SYSCON_RFR_SPI_RESET_ENABLE (0x0040)
|
|
#define U300_SYSCON_RFR_MMC_RESET_ENABLE (0x0020)
|
|
#define U300_SYSCON_RFR_PCM_I2S1_RESET_ENABLE (0x0010)
|
|
#define U300_SYSCON_RFR_PCM_I2S0_RESET_ENABLE (0x0008)
|
|
#define U300_SYSCON_RFR_I2C1_RESET_ENABLE (0x0004)
|
|
#define U300_SYSCON_RFR_I2C0_RESET_ENABLE (0x0002)
|
|
#define U300_SYSCON_RFR_FAST_BRIDGE_RESET_ENABLE (0x0001)
|
|
/* Reset lines for the rest of the peripherals 16bit (R/W) */
|
|
#define U300_SYSCON_RRR (0x001c)
|
|
#define U300_SYSCON_RRR_CDS_RESET_EN (0x4000)
|
|
#define U300_SYSCON_RRR_ISP_RESET_EN (0x2000)
|
|
#define U300_SYSCON_RRR_INTCON_RESET_EN (0x1000)
|
|
#define U300_SYSCON_RRR_MSPRO_RESET_EN (0x0800)
|
|
#define U300_SYSCON_RRR_XGAM_RESET_EN (0x0100)
|
|
#define U300_SYSCON_RRR_XGAM_VC_SYNC_RESET_EN (0x0080)
|
|
#define U300_SYSCON_RRR_NANDIF_RESET_EN (0x0040)
|
|
#define U300_SYSCON_RRR_EMIF_RESET_EN (0x0020)
|
|
#define U300_SYSCON_RRR_DMAC_RESET_EN (0x0010)
|
|
#define U300_SYSCON_RRR_CPU_RESET_EN (0x0008)
|
|
#define U300_SYSCON_RRR_APEX_RESET_EN (0x0004)
|
|
#define U300_SYSCON_RRR_AHB_RESET_EN (0x0002)
|
|
#define U300_SYSCON_RRR_AAIF_RESET_EN (0x0001)
|
|
/* Clock enable for SLOW peripherals 16bit (R/W) */
|
|
#define U300_SYSCON_CESR (0x0020)
|
|
#define U300_SYSCON_CESR_PPM_CLK_EN (0x0200)
|
|
#define U300_SYSCON_CESR_ACC_TMR_CLK_EN (0x0100)
|
|
#define U300_SYSCON_CESR_APP_TMR_CLK_EN (0x0080)
|
|
#define U300_SYSCON_CESR_KEYPAD_CLK_EN (0x0040)
|
|
#define U300_SYSCON_CESR_GPIO_CLK_EN (0x0010)
|
|
#define U300_SYSCON_CESR_EH_CLK_EN (0x0008)
|
|
#define U300_SYSCON_CESR_BTR_CLK_EN (0x0004)
|
|
#define U300_SYSCON_CESR_UART_CLK_EN (0x0002)
|
|
#define U300_SYSCON_CESR_SLOW_BRIDGE_CLK_EN (0x0001)
|
|
/* Clock enable for FAST peripherals 16bit (R/W) */
|
|
#define U300_SYSCON_CEFR (0x0024)
|
|
#define U300_SYSCON_CEFR_UART1_CLK_EN (0x0200)
|
|
#define U300_SYSCON_CEFR_I2S1_CORE_CLK_EN (0x0100)
|
|
#define U300_SYSCON_CEFR_I2S0_CORE_CLK_EN (0x0080)
|
|
#define U300_SYSCON_CEFR_SPI_CLK_EN (0x0040)
|
|
#define U300_SYSCON_CEFR_MMC_CLK_EN (0x0020)
|
|
#define U300_SYSCON_CEFR_I2S1_CLK_EN (0x0010)
|
|
#define U300_SYSCON_CEFR_I2S0_CLK_EN (0x0008)
|
|
#define U300_SYSCON_CEFR_I2C1_CLK_EN (0x0004)
|
|
#define U300_SYSCON_CEFR_I2C0_CLK_EN (0x0002)
|
|
#define U300_SYSCON_CEFR_FAST_BRIDGE_CLK_EN (0x0001)
|
|
/* Clock enable for the rest of the peripherals 16bit (R/W) */
|
|
#define U300_SYSCON_CERR (0x0028)
|
|
#define U300_SYSCON_CERR_CDS_CLK_EN (0x2000)
|
|
#define U300_SYSCON_CERR_ISP_CLK_EN (0x1000)
|
|
#define U300_SYSCON_CERR_MSPRO_CLK_EN (0x0800)
|
|
#define U300_SYSCON_CERR_AHB_SUBSYS_BRIDGE_CLK_EN (0x0400)
|
|
#define U300_SYSCON_CERR_SEMI_CLK_EN (0x0200)
|
|
#define U300_SYSCON_CERR_XGAM_CLK_EN (0x0100)
|
|
#define U300_SYSCON_CERR_VIDEO_ENC_CLK_EN (0x0080)
|
|
#define U300_SYSCON_CERR_NANDIF_CLK_EN (0x0040)
|
|
#define U300_SYSCON_CERR_EMIF_CLK_EN (0x0020)
|
|
#define U300_SYSCON_CERR_DMAC_CLK_EN (0x0010)
|
|
#define U300_SYSCON_CERR_CPU_CLK_EN (0x0008)
|
|
#define U300_SYSCON_CERR_APEX_CLK_EN (0x0004)
|
|
#define U300_SYSCON_CERR_AHB_CLK_EN (0x0002)
|
|
#define U300_SYSCON_CERR_AAIF_CLK_EN (0x0001)
|
|
/* Single block clock enable 16bit (-/W) */
|
|
#define U300_SYSCON_SBCER (0x002c)
|
|
#define U300_SYSCON_SBCER_PPM_CLK_EN (0x0009)
|
|
#define U300_SYSCON_SBCER_ACC_TMR_CLK_EN (0x0008)
|
|
#define U300_SYSCON_SBCER_APP_TMR_CLK_EN (0x0007)
|
|
#define U300_SYSCON_SBCER_KEYPAD_CLK_EN (0x0006)
|
|
#define U300_SYSCON_SBCER_GPIO_CLK_EN (0x0004)
|
|
#define U300_SYSCON_SBCER_EH_CLK_EN (0x0003)
|
|
#define U300_SYSCON_SBCER_BTR_CLK_EN (0x0002)
|
|
#define U300_SYSCON_SBCER_UART_CLK_EN (0x0001)
|
|
#define U300_SYSCON_SBCER_SLOW_BRIDGE_CLK_EN (0x0000)
|
|
#define U300_SYSCON_SBCER_UART1_CLK_EN (0x0019)
|
|
#define U300_SYSCON_SBCER_I2S1_CORE_CLK_EN (0x0018)
|
|
#define U300_SYSCON_SBCER_I2S0_CORE_CLK_EN (0x0017)
|
|
#define U300_SYSCON_SBCER_SPI_CLK_EN (0x0016)
|
|
#define U300_SYSCON_SBCER_MMC_CLK_EN (0x0015)
|
|
#define U300_SYSCON_SBCER_I2S1_CLK_EN (0x0014)
|
|
#define U300_SYSCON_SBCER_I2S0_CLK_EN (0x0013)
|
|
#define U300_SYSCON_SBCER_I2C1_CLK_EN (0x0012)
|
|
#define U300_SYSCON_SBCER_I2C0_CLK_EN (0x0011)
|
|
#define U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN (0x0010)
|
|
#define U300_SYSCON_SBCER_CDS_CLK_EN (0x002D)
|
|
#define U300_SYSCON_SBCER_ISP_CLK_EN (0x002C)
|
|
#define U300_SYSCON_SBCER_MSPRO_CLK_EN (0x002B)
|
|
#define U300_SYSCON_SBCER_AHB_SUBSYS_BRIDGE_CLK_EN (0x002A)
|
|
#define U300_SYSCON_SBCER_SEMI_CLK_EN (0x0029)
|
|
#define U300_SYSCON_SBCER_XGAM_CLK_EN (0x0028)
|
|
#define U300_SYSCON_SBCER_VIDEO_ENC_CLK_EN (0x0027)
|
|
#define U300_SYSCON_SBCER_NANDIF_CLK_EN (0x0026)
|
|
#define U300_SYSCON_SBCER_EMIF_CLK_EN (0x0025)
|
|
#define U300_SYSCON_SBCER_DMAC_CLK_EN (0x0024)
|
|
#define U300_SYSCON_SBCER_CPU_CLK_EN (0x0023)
|
|
#define U300_SYSCON_SBCER_APEX_CLK_EN (0x0022)
|
|
#define U300_SYSCON_SBCER_AHB_CLK_EN (0x0021)
|
|
#define U300_SYSCON_SBCER_AAIF_CLK_EN (0x0020)
|
|
/* Single block clock disable 16bit (-/W) */
|
|
#define U300_SYSCON_SBCDR (0x0030)
|
|
/* Same values as above for SBCER */
|
|
/* Clock force SLOW peripherals 16bit (R/W) */
|
|
#define U300_SYSCON_CFSR (0x003c)
|
|
#define U300_SYSCON_CFSR_PPM_CLK_FORCE_EN (0x0200)
|
|
#define U300_SYSCON_CFSR_ACC_TMR_CLK_FORCE_EN (0x0100)
|
|
#define U300_SYSCON_CFSR_APP_TMR_CLK_FORCE_EN (0x0080)
|
|
#define U300_SYSCON_CFSR_KEYPAD_CLK_FORCE_EN (0x0020)
|
|
#define U300_SYSCON_CFSR_GPIO_CLK_FORCE_EN (0x0010)
|
|
#define U300_SYSCON_CFSR_EH_CLK_FORCE_EN (0x0008)
|
|
#define U300_SYSCON_CFSR_BTR_CLK_FORCE_EN (0x0004)
|
|
#define U300_SYSCON_CFSR_UART_CLK_FORCE_EN (0x0002)
|
|
#define U300_SYSCON_CFSR_SLOW_BRIDGE_CLK_FORCE_EN (0x0001)
|
|
/* Clock force FAST peripherals 16bit (R/W) */
|
|
#define U300_SYSCON_CFFR (0x40)
|
|
/* Values not defined. Define if you want to use them. */
|
|
/* Clock force the rest of the peripherals 16bit (R/W) */
|
|
#define U300_SYSCON_CFRR (0x44)
|
|
#define U300_SYSCON_CFRR_CDS_CLK_FORCE_EN (0x2000)
|
|
#define U300_SYSCON_CFRR_ISP_CLK_FORCE_EN (0x1000)
|
|
#define U300_SYSCON_CFRR_MSPRO_CLK_FORCE_EN (0x0800)
|
|
#define U300_SYSCON_CFRR_AHB_SUBSYS_BRIDGE_CLK_FORCE_EN (0x0400)
|
|
#define U300_SYSCON_CFRR_SEMI_CLK_FORCE_EN (0x0200)
|
|
#define U300_SYSCON_CFRR_XGAM_CLK_FORCE_EN (0x0100)
|
|
#define U300_SYSCON_CFRR_VIDEO_ENC_CLK_FORCE_EN (0x0080)
|
|
#define U300_SYSCON_CFRR_NANDIF_CLK_FORCE_EN (0x0040)
|
|
#define U300_SYSCON_CFRR_EMIF_CLK_FORCE_EN (0x0020)
|
|
#define U300_SYSCON_CFRR_DMAC_CLK_FORCE_EN (0x0010)
|
|
#define U300_SYSCON_CFRR_CPU_CLK_FORCE_EN (0x0008)
|
|
#define U300_SYSCON_CFRR_APEX_CLK_FORCE_EN (0x0004)
|
|
#define U300_SYSCON_CFRR_AHB_CLK_FORCE_EN (0x0002)
|
|
#define U300_SYSCON_CFRR_AAIF_CLK_FORCE_EN (0x0001)
|
|
/* PLL208 Frequency Control 16bit (R/W) */
|
|
#define U300_SYSCON_PFCR (0x48)
|
|
#define U300_SYSCON_PFCR_DPLL_MULT_NUM (0x000F)
|
|
/* Power Management Control 16bit (R/W) */
|
|
#define U300_SYSCON_PMCR (0x50)
|
|
#define U300_SYSCON_PMCR_DCON_ENABLE (0x0002)
|
|
#define U300_SYSCON_PMCR_PWR_MGNT_ENABLE (0x0001)
|
|
/* Reset Out 16bit (R/W) */
|
|
#define U300_SYSCON_RCR (0x6c)
|
|
#define U300_SYSCON_RCR_RESOUT0_RST_N_DISABLE (0x0001)
|
|
/* EMIF Slew Rate Control 16bit (R/W) */
|
|
#define U300_SYSCON_SRCLR (0x70)
|
|
#define U300_SYSCON_SRCLR_MASK (0x03FF)
|
|
#define U300_SYSCON_SRCLR_VALUE (0x03FF)
|
|
#define U300_SYSCON_SRCLR_EMIF_1_SLRC_5_B (0x0200)
|
|
#define U300_SYSCON_SRCLR_EMIF_1_SLRC_5_A (0x0100)
|
|
#define U300_SYSCON_SRCLR_EMIF_1_SLRC_4_B (0x0080)
|
|
#define U300_SYSCON_SRCLR_EMIF_1_SLRC_4_A (0x0040)
|
|
#define U300_SYSCON_SRCLR_EMIF_1_SLRC_3_B (0x0020)
|
|
#define U300_SYSCON_SRCLR_EMIF_1_SLRC_3_A (0x0010)
|
|
#define U300_SYSCON_SRCLR_EMIF_1_SLRC_2_B (0x0008)
|
|
#define U300_SYSCON_SRCLR_EMIF_1_SLRC_2_A (0x0004)
|
|
#define U300_SYSCON_SRCLR_EMIF_1_SLRC_1_B (0x0002)
|
|
#define U300_SYSCON_SRCLR_EMIF_1_SLRC_1_A (0x0001)
|
|
/* EMIF Clock Control Register 16bit (R/W) */
|
|
#define U300_SYSCON_ECCR (0x0078)
|
|
#define U300_SYSCON_ECCR_MASK (0x000F)
|
|
#define U300_SYSCON_ECCR_EMIF_1_STATIC_CLK_EN_N_DISABLE (0x0008)
|
|
#define U300_SYSCON_ECCR_EMIF_1_RET_OUT_CLK_EN_N_DISABLE (0x0004)
|
|
#define U300_SYSCON_ECCR_EMIF_MEMCLK_RET_EN_N_DISABLE (0x0002)
|
|
#define U300_SYSCON_ECCR_EMIF_SDRCLK_RET_EN_N_DISABLE (0x0001)
|
|
/* MMC/MSPRO frequency divider register 0 16bit (R/W) */
|
|
#define U300_SYSCON_MMF0R (0x90)
|
|
#define U300_SYSCON_MMF0R_MASK (0x00FF)
|
|
#define U300_SYSCON_MMF0R_FREQ_0_HIGH_MASK (0x00F0)
|
|
#define U300_SYSCON_MMF0R_FREQ_0_LOW_MASK (0x000F)
|
|
/* MMC/MSPRO frequency divider register 1 16bit (R/W) */
|
|
#define U300_SYSCON_MMF1R (0x94)
|
|
#define U300_SYSCON_MMF1R_MASK (0x00FF)
|
|
#define U300_SYSCON_MMF1R_FREQ_1_HIGH_MASK (0x00F0)
|
|
#define U300_SYSCON_MMF1R_FREQ_1_LOW_MASK (0x000F)
|
|
/* Clock control for the MMC and MSPRO blocks 16bit (R/W) */
|
|
#define U300_SYSCON_MMCR (0x9C)
|
|
#define U300_SYSCON_MMCR_MASK (0x0003)
|
|
#define U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE (0x0002)
|
|
#define U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE (0x0001)
|
|
/* SYS_0_CLK_CONTROL first clock control 16bit (R/W) */
|
|
#define U300_SYSCON_S0CCR (0x120)
|
|
#define U300_SYSCON_S0CCR_FIELD_MASK (0x43FF)
|
|
#define U300_SYSCON_S0CCR_CLOCK_REQ (0x4000)
|
|
#define U300_SYSCON_S0CCR_CLOCK_REQ_MONITOR (0x2000)
|
|
#define U300_SYSCON_S0CCR_CLOCK_INV (0x0200)
|
|
#define U300_SYSCON_S0CCR_CLOCK_FREQ_MASK (0x01E0)
|
|
#define U300_SYSCON_S0CCR_CLOCK_SELECT_MASK (0x001E)
|
|
#define U300_SYSCON_S0CCR_CLOCK_ENABLE (0x0001)
|
|
#define U300_SYSCON_S0CCR_SEL_MCLK (0x8<<1)
|
|
#define U300_SYSCON_S0CCR_SEL_ACC_FSM_CLK (0xA<<1)
|
|
#define U300_SYSCON_S0CCR_SEL_PLL60_48_CLK (0xC<<1)
|
|
#define U300_SYSCON_S0CCR_SEL_PLL60_60_CLK (0xD<<1)
|
|
#define U300_SYSCON_S0CCR_SEL_ACC_PLL208_CLK (0xE<<1)
|
|
#define U300_SYSCON_S0CCR_SEL_APP_PLL13_CLK (0x0<<1)
|
|
#define U300_SYSCON_S0CCR_SEL_APP_FSM_CLK (0x2<<1)
|
|
#define U300_SYSCON_S0CCR_SEL_RTC_CLK (0x4<<1)
|
|
#define U300_SYSCON_S0CCR_SEL_APP_PLL208_CLK (0x6<<1)
|
|
/* SYS_1_CLK_CONTROL second clock control 16 bit (R/W) */
|
|
#define U300_SYSCON_S1CCR (0x124)
|
|
#define U300_SYSCON_S1CCR_FIELD_MASK (0x43FF)
|
|
#define U300_SYSCON_S1CCR_CLOCK_REQ (0x4000)
|
|
#define U300_SYSCON_S1CCR_CLOCK_REQ_MONITOR (0x2000)
|
|
#define U300_SYSCON_S1CCR_CLOCK_INV (0x0200)
|
|
#define U300_SYSCON_S1CCR_CLOCK_FREQ_MASK (0x01E0)
|
|
#define U300_SYSCON_S1CCR_CLOCK_SELECT_MASK (0x001E)
|
|
#define U300_SYSCON_S1CCR_CLOCK_ENABLE (0x0001)
|
|
#define U300_SYSCON_S1CCR_SEL_MCLK (0x8<<1)
|
|
#define U300_SYSCON_S1CCR_SEL_ACC_FSM_CLK (0xA<<1)
|
|
#define U300_SYSCON_S1CCR_SEL_PLL60_48_CLK (0xC<<1)
|
|
#define U300_SYSCON_S1CCR_SEL_PLL60_60_CLK (0xD<<1)
|
|
#define U300_SYSCON_S1CCR_SEL_ACC_PLL208_CLK (0xE<<1)
|
|
#define U300_SYSCON_S1CCR_SEL_ACC_PLL13_CLK (0x0<<1)
|
|
#define U300_SYSCON_S1CCR_SEL_APP_FSM_CLK (0x2<<1)
|
|
#define U300_SYSCON_S1CCR_SEL_RTC_CLK (0x4<<1)
|
|
#define U300_SYSCON_S1CCR_SEL_APP_PLL208_CLK (0x6<<1)
|
|
/* SYS_2_CLK_CONTROL third clock contol 16 bit (R/W) */
|
|
#define U300_SYSCON_S2CCR (0x128)
|
|
#define U300_SYSCON_S2CCR_FIELD_MASK (0xC3FF)
|
|
#define U300_SYSCON_S2CCR_CLK_STEAL (0x8000)
|
|
#define U300_SYSCON_S2CCR_CLOCK_REQ (0x4000)
|
|
#define U300_SYSCON_S2CCR_CLOCK_REQ_MONITOR (0x2000)
|
|
#define U300_SYSCON_S2CCR_CLOCK_INV (0x0200)
|
|
#define U300_SYSCON_S2CCR_CLOCK_FREQ_MASK (0x01E0)
|
|
#define U300_SYSCON_S2CCR_CLOCK_SELECT_MASK (0x001E)
|
|
#define U300_SYSCON_S2CCR_CLOCK_ENABLE (0x0001)
|
|
#define U300_SYSCON_S2CCR_SEL_MCLK (0x8<<1)
|
|
#define U300_SYSCON_S2CCR_SEL_ACC_FSM_CLK (0xA<<1)
|
|
#define U300_SYSCON_S2CCR_SEL_PLL60_48_CLK (0xC<<1)
|
|
#define U300_SYSCON_S2CCR_SEL_PLL60_60_CLK (0xD<<1)
|
|
#define U300_SYSCON_S2CCR_SEL_ACC_PLL208_CLK (0xE<<1)
|
|
#define U300_SYSCON_S2CCR_SEL_ACC_PLL13_CLK (0x0<<1)
|
|
#define U300_SYSCON_S2CCR_SEL_APP_FSM_CLK (0x2<<1)
|
|
#define U300_SYSCON_S2CCR_SEL_RTC_CLK (0x4<<1)
|
|
#define U300_SYSCON_S2CCR_SEL_APP_PLL208_CLK (0x6<<1)
|
|
/* SC_PLL_IRQ_CONTROL 16bit (R/W) */
|
|
#define U300_SYSCON_PICR (0x0130)
|
|
#define U300_SYSCON_PICR_MASK (0x00FF)
|
|
#define U300_SYSCON_PICR_FORCE_PLL208_LOCK_LOW_ENABLE (0x0080)
|
|
#define U300_SYSCON_PICR_FORCE_PLL208_LOCK_HIGH_ENABLE (0x0040)
|
|
#define U300_SYSCON_PICR_FORCE_PLL13_LOCK_LOW_ENABLE (0x0020)
|
|
#define U300_SYSCON_PICR_FORCE_PLL13_LOCK_HIGH_ENABLE (0x0010)
|
|
#define U300_SYSCON_PICR_IRQMASK_PLL13_UNLOCK_ENABLE (0x0008)
|
|
#define U300_SYSCON_PICR_IRQMASK_PLL13_LOCK_ENABLE (0x0004)
|
|
#define U300_SYSCON_PICR_IRQMASK_PLL208_UNLOCK_ENABLE (0x0002)
|
|
#define U300_SYSCON_PICR_IRQMASK_PLL208_LOCK_ENABLE (0x0001)
|
|
/* SC_PLL_IRQ_STATUS 16 bit (R/-) */
|
|
#define U300_SYSCON_PISR (0x0134)
|
|
#define U300_SYSCON_PISR_MASK (0x000F)
|
|
#define U300_SYSCON_PISR_PLL13_UNLOCK_IND (0x0008)
|
|
#define U300_SYSCON_PISR_PLL13_LOCK_IND (0x0004)
|
|
#define U300_SYSCON_PISR_PLL208_UNLOCK_IND (0x0002)
|
|
#define U300_SYSCON_PISR_PLL208_LOCK_IND (0x0001)
|
|
/* SC_PLL_IRQ_CLEAR 16 bit (-/W) */
|
|
#define U300_SYSCON_PICLR (0x0138)
|
|
#define U300_SYSCON_PICLR_MASK (0x000F)
|
|
#define U300_SYSCON_PICLR_RWMASK (0x0000)
|
|
#define U300_SYSCON_PICLR_PLL13_UNLOCK_SC (0x0008)
|
|
#define U300_SYSCON_PICLR_PLL13_LOCK_SC (0x0004)
|
|
#define U300_SYSCON_PICLR_PLL208_UNLOCK_SC (0x0002)
|
|
#define U300_SYSCON_PICLR_PLL208_LOCK_SC (0x0001)
|
|
/* Clock activity observability register 0 */
|
|
#define U300_SYSCON_C0OAR (0x140)
|
|
#define U300_SYSCON_C0OAR_MASK (0xFFFF)
|
|
#define U300_SYSCON_C0OAR_VALUE (0xFFFF)
|
|
#define U300_SYSCON_C0OAR_BT_H_CLK (0x8000)
|
|
#define U300_SYSCON_C0OAR_ASPB_P_CLK (0x4000)
|
|
#define U300_SYSCON_C0OAR_APP_SEMI_H_CLK (0x2000)
|
|
#define U300_SYSCON_C0OAR_APP_SEMI_CLK (0x1000)
|
|
#define U300_SYSCON_C0OAR_APP_MMC_MSPRO_CLK (0x0800)
|
|
#define U300_SYSCON_C0OAR_APP_I2S1_CLK (0x0400)
|
|
#define U300_SYSCON_C0OAR_APP_I2S0_CLK (0x0200)
|
|
#define U300_SYSCON_C0OAR_APP_CPU_CLK (0x0100)
|
|
#define U300_SYSCON_C0OAR_APP_52_CLK (0x0080)
|
|
#define U300_SYSCON_C0OAR_APP_208_CLK (0x0040)
|
|
#define U300_SYSCON_C0OAR_APP_104_CLK (0x0020)
|
|
#define U300_SYSCON_C0OAR_APEX_CLK (0x0010)
|
|
#define U300_SYSCON_C0OAR_AHPB_M_H_CLK (0x0008)
|
|
#define U300_SYSCON_C0OAR_AHB_CLK (0x0004)
|
|
#define U300_SYSCON_C0OAR_AFPB_P_CLK (0x0002)
|
|
#define U300_SYSCON_C0OAR_AAIF_CLK (0x0001)
|
|
/* Clock activity observability register 1 */
|
|
#define U300_SYSCON_C1OAR (0x144)
|
|
#define U300_SYSCON_C1OAR_MASK (0x3FFE)
|
|
#define U300_SYSCON_C1OAR_VALUE (0x3FFE)
|
|
#define U300_SYSCON_C1OAR_NFIF_F_CLK (0x2000)
|
|
#define U300_SYSCON_C1OAR_MSPRO_CLK (0x1000)
|
|
#define U300_SYSCON_C1OAR_MMC_P_CLK (0x0800)
|
|
#define U300_SYSCON_C1OAR_MMC_CLK (0x0400)
|
|
#define U300_SYSCON_C1OAR_KP_P_CLK (0x0200)
|
|
#define U300_SYSCON_C1OAR_I2C1_P_CLK (0x0100)
|
|
#define U300_SYSCON_C1OAR_I2C0_P_CLK (0x0080)
|
|
#define U300_SYSCON_C1OAR_GPIO_CLK (0x0040)
|
|
#define U300_SYSCON_C1OAR_EMIF_MPMC_CLK (0x0020)
|
|
#define U300_SYSCON_C1OAR_EMIF_H_CLK (0x0010)
|
|
#define U300_SYSCON_C1OAR_EVHIST_CLK (0x0008)
|
|
#define U300_SYSCON_C1OAR_PPM_CLK (0x0004)
|
|
#define U300_SYSCON_C1OAR_DMA_CLK (0x0002)
|
|
/* Clock activity observability register 2 */
|
|
#define U300_SYSCON_C2OAR (0x148)
|
|
#define U300_SYSCON_C2OAR_MASK (0x0FFF)
|
|
#define U300_SYSCON_C2OAR_VALUE (0x0FFF)
|
|
#define U300_SYSCON_C2OAR_XGAM_CDI_CLK (0x0800)
|
|
#define U300_SYSCON_C2OAR_XGAM_CLK (0x0400)
|
|
#define U300_SYSCON_C2OAR_VC_H_CLK (0x0200)
|
|
#define U300_SYSCON_C2OAR_VC_CLK (0x0100)
|
|
#define U300_SYSCON_C2OAR_UA_P_CLK (0x0080)
|
|
#define U300_SYSCON_C2OAR_TMR1_CLK (0x0040)
|
|
#define U300_SYSCON_C2OAR_TMR0_CLK (0x0020)
|
|
#define U300_SYSCON_C2OAR_SPI_P_CLK (0x0010)
|
|
#define U300_SYSCON_C2OAR_PCM_I2S1_CORE_CLK (0x0008)
|
|
#define U300_SYSCON_C2OAR_PCM_I2S1_CLK (0x0004)
|
|
#define U300_SYSCON_C2OAR_PCM_I2S0_CORE_CLK (0x0002)
|
|
#define U300_SYSCON_C2OAR_PCM_I2S0_CLK (0x0001)
|
|
|
|
|
|
/*
|
|
* The clocking hierarchy currently looks like this.
|
|
* NOTE: the idea is NOT to show how the clocks are routed on the chip!
|
|
* The ideas is to show dependencies, so a clock higher up in the
|
|
* hierarchy has to be on in order for another clock to be on. Now,
|
|
* both CPU and DMA can actually be on top of the hierarchy, and that
|
|
* is not modeled currently. Instead we have the backbone AMBA bus on
|
|
* top. This bus cannot be programmed in any way but conceptually it
|
|
* needs to be active for the bridges and devices to transport data.
|
|
*
|
|
* Please be aware that a few clocks are hw controlled, which mean that
|
|
* the hw itself can turn on/off or change the rate of the clock when
|
|
* needed!
|
|
*
|
|
* AMBA bus
|
|
* |
|
|
* +- CPU
|
|
* +- FSMC NANDIF NAND Flash interface
|
|
* +- SEMI Shared Memory interface
|
|
* +- ISP Image Signal Processor (U335 only)
|
|
* +- CDS (U335 only)
|
|
* +- DMA Direct Memory Access Controller
|
|
* +- AAIF APP/ACC Inteface (Mobile Scalable Link, MSL)
|
|
* +- APEX
|
|
* +- VIDEO_ENC AVE2/3 Video Encoder
|
|
* +- XGAM Graphics Accelerator Controller
|
|
* +- AHB
|
|
* |
|
|
* +- ahb:0 AHB Bridge
|
|
* | |
|
|
* | +- ahb:1 INTCON Interrupt controller
|
|
* | +- ahb:3 MSPRO Memory Stick Pro controller
|
|
* | +- ahb:4 EMIF External Memory interface
|
|
* |
|
|
* +- fast:0 FAST bridge
|
|
* | |
|
|
* | +- fast:1 MMCSD MMC/SD card reader controller
|
|
* | +- fast:2 I2S0 PCM I2S channel 0 controller
|
|
* | +- fast:3 I2S1 PCM I2S channel 1 controller
|
|
* | +- fast:4 I2C0 I2C channel 0 controller
|
|
* | +- fast:5 I2C1 I2C channel 1 controller
|
|
* | +- fast:6 SPI SPI controller
|
|
* | +- fast:7 UART1 Secondary UART (U335 only)
|
|
* |
|
|
* +- slow:0 SLOW bridge
|
|
* |
|
|
* +- slow:1 SYSCON (not possible to control)
|
|
* +- slow:2 WDOG Watchdog
|
|
* +- slow:3 UART0 primary UART
|
|
* +- slow:4 TIMER_APP Application timer - used in Linux
|
|
* +- slow:5 KEYPAD controller
|
|
* +- slow:6 GPIO controller
|
|
* +- slow:7 RTC controller
|
|
* +- slow:8 BT Bus Tracer (not used currently)
|
|
* +- slow:9 EH Event Handler (not used currently)
|
|
* +- slow:a TIMER_ACC Access style timer (not used currently)
|
|
* +- slow:b PPM (U335 only, what is that?)
|
|
*/
|
|
|
|
/* Global syscon virtual base */
|
|
static void __iomem *syscon_vbase;
|
|
|
|
/**
|
|
* struct clk_syscon - U300 syscon clock
|
|
* @hw: corresponding clock hardware entry
|
|
* @hw_ctrld: whether this clock is hardware controlled (for refcount etc)
|
|
* and does not need any magic pokes to be enabled/disabled
|
|
* @reset: state holder, whether this block's reset line is asserted or not
|
|
* @res_reg: reset line enable/disable flag register
|
|
* @res_bit: bit for resetting or taking this consumer out of reset
|
|
* @en_reg: clock line enable/disable flag register
|
|
* @en_bit: bit for enabling/disabling this consumer clock line
|
|
* @clk_val: magic value to poke in the register to enable/disable
|
|
* this one clock
|
|
*/
|
|
struct clk_syscon {
|
|
struct clk_hw hw;
|
|
bool hw_ctrld;
|
|
bool reset;
|
|
void __iomem *res_reg;
|
|
u8 res_bit;
|
|
void __iomem *en_reg;
|
|
u8 en_bit;
|
|
u16 clk_val;
|
|
};
|
|
|
|
#define to_syscon(_hw) container_of(_hw, struct clk_syscon, hw)
|
|
|
|
static DEFINE_SPINLOCK(syscon_resetreg_lock);
|
|
|
|
/*
|
|
* Reset control functions. We remember if a block has been
|
|
* taken out of reset and don't remove the reset assertion again
|
|
* and vice versa. Currently we only remove resets so the
|
|
* enablement function is defined out.
|
|
*/
|
|
static void syscon_block_reset_enable(struct clk_syscon *sclk)
|
|
{
|
|
unsigned long iflags;
|
|
u16 val;
|
|
|
|
/* Not all blocks support resetting */
|
|
if (!sclk->res_reg)
|
|
return;
|
|
spin_lock_irqsave(&syscon_resetreg_lock, iflags);
|
|
val = readw(sclk->res_reg);
|
|
val |= BIT(sclk->res_bit);
|
|
writew(val, sclk->res_reg);
|
|
spin_unlock_irqrestore(&syscon_resetreg_lock, iflags);
|
|
sclk->reset = true;
|
|
}
|
|
|
|
static void syscon_block_reset_disable(struct clk_syscon *sclk)
|
|
{
|
|
unsigned long iflags;
|
|
u16 val;
|
|
|
|
/* Not all blocks support resetting */
|
|
if (!sclk->res_reg)
|
|
return;
|
|
spin_lock_irqsave(&syscon_resetreg_lock, iflags);
|
|
val = readw(sclk->res_reg);
|
|
val &= ~BIT(sclk->res_bit);
|
|
writew(val, sclk->res_reg);
|
|
spin_unlock_irqrestore(&syscon_resetreg_lock, iflags);
|
|
sclk->reset = false;
|
|
}
|
|
|
|
static int syscon_clk_prepare(struct clk_hw *hw)
|
|
{
|
|
struct clk_syscon *sclk = to_syscon(hw);
|
|
|
|
/* If the block is in reset, bring it out */
|
|
if (sclk->reset)
|
|
syscon_block_reset_disable(sclk);
|
|
return 0;
|
|
}
|
|
|
|
static void syscon_clk_unprepare(struct clk_hw *hw)
|
|
{
|
|
struct clk_syscon *sclk = to_syscon(hw);
|
|
|
|
/* Please don't force the console into reset */
|
|
if (sclk->clk_val == U300_SYSCON_SBCER_UART_CLK_EN)
|
|
return;
|
|
/* When unpreparing, force block into reset */
|
|
if (!sclk->reset)
|
|
syscon_block_reset_enable(sclk);
|
|
}
|
|
|
|
static int syscon_clk_enable(struct clk_hw *hw)
|
|
{
|
|
struct clk_syscon *sclk = to_syscon(hw);
|
|
|
|
/* Don't touch the hardware controlled clocks */
|
|
if (sclk->hw_ctrld)
|
|
return 0;
|
|
/* These cannot be controlled */
|
|
if (sclk->clk_val == 0xFFFFU)
|
|
return 0;
|
|
|
|
writew(sclk->clk_val, syscon_vbase + U300_SYSCON_SBCER);
|
|
return 0;
|
|
}
|
|
|
|
static void syscon_clk_disable(struct clk_hw *hw)
|
|
{
|
|
struct clk_syscon *sclk = to_syscon(hw);
|
|
|
|
/* Don't touch the hardware controlled clocks */
|
|
if (sclk->hw_ctrld)
|
|
return;
|
|
if (sclk->clk_val == 0xFFFFU)
|
|
return;
|
|
/* Please don't disable the console port */
|
|
if (sclk->clk_val == U300_SYSCON_SBCER_UART_CLK_EN)
|
|
return;
|
|
|
|
writew(sclk->clk_val, syscon_vbase + U300_SYSCON_SBCDR);
|
|
}
|
|
|
|
static int syscon_clk_is_enabled(struct clk_hw *hw)
|
|
{
|
|
struct clk_syscon *sclk = to_syscon(hw);
|
|
u16 val;
|
|
|
|
/* If no enable register defined, it's always-on */
|
|
if (!sclk->en_reg)
|
|
return 1;
|
|
|
|
val = readw(sclk->en_reg);
|
|
val &= BIT(sclk->en_bit);
|
|
|
|
return val ? 1 : 0;
|
|
}
|
|
|
|
static u16 syscon_get_perf(void)
|
|
{
|
|
u16 val;
|
|
|
|
val = readw(syscon_vbase + U300_SYSCON_CCR);
|
|
val &= U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK;
|
|
return val;
|
|
}
|
|
|
|
static unsigned long
|
|
syscon_clk_recalc_rate(struct clk_hw *hw,
|
|
unsigned long parent_rate)
|
|
{
|
|
struct clk_syscon *sclk = to_syscon(hw);
|
|
u16 perf = syscon_get_perf();
|
|
|
|
switch(sclk->clk_val) {
|
|
case U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN:
|
|
case U300_SYSCON_SBCER_I2C0_CLK_EN:
|
|
case U300_SYSCON_SBCER_I2C1_CLK_EN:
|
|
case U300_SYSCON_SBCER_MMC_CLK_EN:
|
|
case U300_SYSCON_SBCER_SPI_CLK_EN:
|
|
/* The FAST clocks have one progression */
|
|
switch(perf) {
|
|
case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
|
|
case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
|
|
return 13000000;
|
|
default:
|
|
return parent_rate; /* 26 MHz */
|
|
}
|
|
case U300_SYSCON_SBCER_DMAC_CLK_EN:
|
|
case U300_SYSCON_SBCER_NANDIF_CLK_EN:
|
|
case U300_SYSCON_SBCER_XGAM_CLK_EN:
|
|
/* AMBA interconnect peripherals */
|
|
switch(perf) {
|
|
case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
|
|
case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
|
|
return 6500000;
|
|
case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
|
|
return 26000000;
|
|
default:
|
|
return parent_rate; /* 52 MHz */
|
|
}
|
|
case U300_SYSCON_SBCER_SEMI_CLK_EN:
|
|
case U300_SYSCON_SBCER_EMIF_CLK_EN:
|
|
/* EMIF speeds */
|
|
switch(perf) {
|
|
case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
|
|
case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
|
|
return 13000000;
|
|
case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
|
|
return 52000000;
|
|
default:
|
|
return 104000000;
|
|
}
|
|
case U300_SYSCON_SBCER_CPU_CLK_EN:
|
|
/* And the fast CPU clock */
|
|
switch(perf) {
|
|
case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
|
|
case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
|
|
return 13000000;
|
|
case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
|
|
return 52000000;
|
|
case U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH:
|
|
return 104000000;
|
|
default:
|
|
return parent_rate; /* 208 MHz */
|
|
}
|
|
default:
|
|
/*
|
|
* The SLOW clocks and default just inherit the rate of
|
|
* their parent (typically PLL13 13 MHz).
|
|
*/
|
|
return parent_rate;
|
|
}
|
|
}
|
|
|
|
static long
|
|
syscon_clk_round_rate(struct clk_hw *hw, unsigned long rate,
|
|
unsigned long *prate)
|
|
{
|
|
struct clk_syscon *sclk = to_syscon(hw);
|
|
|
|
if (sclk->clk_val != U300_SYSCON_SBCER_CPU_CLK_EN)
|
|
return *prate;
|
|
/* We really only support setting the rate of the CPU clock */
|
|
if (rate <= 13000000)
|
|
return 13000000;
|
|
if (rate <= 52000000)
|
|
return 52000000;
|
|
if (rate <= 104000000)
|
|
return 104000000;
|
|
return 208000000;
|
|
}
|
|
|
|
static int syscon_clk_set_rate(struct clk_hw *hw, unsigned long rate,
|
|
unsigned long parent_rate)
|
|
{
|
|
struct clk_syscon *sclk = to_syscon(hw);
|
|
u16 val;
|
|
|
|
/* We only support setting the rate of the CPU clock */
|
|
if (sclk->clk_val != U300_SYSCON_SBCER_CPU_CLK_EN)
|
|
return -EINVAL;
|
|
switch (rate) {
|
|
case 13000000:
|
|
val = U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER;
|
|
break;
|
|
case 52000000:
|
|
val = U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE;
|
|
break;
|
|
case 104000000:
|
|
val = U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH;
|
|
break;
|
|
case 208000000:
|
|
val = U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST;
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
val |= readw(syscon_vbase + U300_SYSCON_CCR) &
|
|
~U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK ;
|
|
writew(val, syscon_vbase + U300_SYSCON_CCR);
|
|
return 0;
|
|
}
|
|
|
|
static const struct clk_ops syscon_clk_ops = {
|
|
.prepare = syscon_clk_prepare,
|
|
.unprepare = syscon_clk_unprepare,
|
|
.enable = syscon_clk_enable,
|
|
.disable = syscon_clk_disable,
|
|
.is_enabled = syscon_clk_is_enabled,
|
|
.recalc_rate = syscon_clk_recalc_rate,
|
|
.round_rate = syscon_clk_round_rate,
|
|
.set_rate = syscon_clk_set_rate,
|
|
};
|
|
|
|
static struct clk * __init
|
|
syscon_clk_register(struct device *dev, const char *name,
|
|
const char *parent_name, unsigned long flags,
|
|
bool hw_ctrld,
|
|
void __iomem *res_reg, u8 res_bit,
|
|
void __iomem *en_reg, u8 en_bit,
|
|
u16 clk_val)
|
|
{
|
|
struct clk *clk;
|
|
struct clk_syscon *sclk;
|
|
struct clk_init_data init;
|
|
|
|
sclk = kzalloc(sizeof(struct clk_syscon), GFP_KERNEL);
|
|
if (!sclk) {
|
|
pr_err("could not allocate syscon clock %s\n",
|
|
name);
|
|
return ERR_PTR(-ENOMEM);
|
|
}
|
|
init.name = name;
|
|
init.ops = &syscon_clk_ops;
|
|
init.flags = flags;
|
|
init.parent_names = (parent_name ? &parent_name : NULL);
|
|
init.num_parents = (parent_name ? 1 : 0);
|
|
sclk->hw.init = &init;
|
|
sclk->hw_ctrld = hw_ctrld;
|
|
/* Assume the block is in reset at registration */
|
|
sclk->reset = true;
|
|
sclk->res_reg = res_reg;
|
|
sclk->res_bit = res_bit;
|
|
sclk->en_reg = en_reg;
|
|
sclk->en_bit = en_bit;
|
|
sclk->clk_val = clk_val;
|
|
|
|
clk = clk_register(dev, &sclk->hw);
|
|
if (IS_ERR(clk))
|
|
kfree(sclk);
|
|
|
|
return clk;
|
|
}
|
|
|
|
#define U300_CLK_TYPE_SLOW 0
|
|
#define U300_CLK_TYPE_FAST 1
|
|
#define U300_CLK_TYPE_REST 2
|
|
|
|
/**
|
|
* struct u300_clock - defines the bits and pieces for a certain clock
|
|
* @type: the clock type, slow fast or rest
|
|
* @id: the bit in the slow/fast/rest register for this clock
|
|
* @hw_ctrld: whether the clock is hardware controlled
|
|
* @clk_val: a value to poke in the one-write enable/disable registers
|
|
*/
|
|
struct u300_clock {
|
|
u8 type;
|
|
u8 id;
|
|
bool hw_ctrld;
|
|
u16 clk_val;
|
|
};
|
|
|
|
static struct u300_clock const u300_clk_lookup[] __initconst = {
|
|
{
|
|
.type = U300_CLK_TYPE_REST,
|
|
.id = 3,
|
|
.hw_ctrld = true,
|
|
.clk_val = U300_SYSCON_SBCER_CPU_CLK_EN,
|
|
},
|
|
{
|
|
.type = U300_CLK_TYPE_REST,
|
|
.id = 4,
|
|
.hw_ctrld = true,
|
|
.clk_val = U300_SYSCON_SBCER_DMAC_CLK_EN,
|
|
},
|
|
{
|
|
.type = U300_CLK_TYPE_REST,
|
|
.id = 5,
|
|
.hw_ctrld = false,
|
|
.clk_val = U300_SYSCON_SBCER_EMIF_CLK_EN,
|
|
},
|
|
{
|
|
.type = U300_CLK_TYPE_REST,
|
|
.id = 6,
|
|
.hw_ctrld = false,
|
|
.clk_val = U300_SYSCON_SBCER_NANDIF_CLK_EN,
|
|
},
|
|
{
|
|
.type = U300_CLK_TYPE_REST,
|
|
.id = 8,
|
|
.hw_ctrld = true,
|
|
.clk_val = U300_SYSCON_SBCER_XGAM_CLK_EN,
|
|
},
|
|
{
|
|
.type = U300_CLK_TYPE_REST,
|
|
.id = 9,
|
|
.hw_ctrld = false,
|
|
.clk_val = U300_SYSCON_SBCER_SEMI_CLK_EN,
|
|
},
|
|
{
|
|
.type = U300_CLK_TYPE_REST,
|
|
.id = 10,
|
|
.hw_ctrld = true,
|
|
.clk_val = U300_SYSCON_SBCER_AHB_SUBSYS_BRIDGE_CLK_EN,
|
|
},
|
|
{
|
|
.type = U300_CLK_TYPE_REST,
|
|
.id = 12,
|
|
.hw_ctrld = false,
|
|
/* INTCON: cannot be enabled, just taken out of reset */
|
|
.clk_val = 0xFFFFU,
|
|
},
|
|
{
|
|
.type = U300_CLK_TYPE_FAST,
|
|
.id = 0,
|
|
.hw_ctrld = true,
|
|
.clk_val = U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN,
|
|
},
|
|
{
|
|
.type = U300_CLK_TYPE_FAST,
|
|
.id = 1,
|
|
.hw_ctrld = false,
|
|
.clk_val = U300_SYSCON_SBCER_I2C0_CLK_EN,
|
|
},
|
|
{
|
|
.type = U300_CLK_TYPE_FAST,
|
|
.id = 2,
|
|
.hw_ctrld = false,
|
|
.clk_val = U300_SYSCON_SBCER_I2C1_CLK_EN,
|
|
},
|
|
{
|
|
.type = U300_CLK_TYPE_FAST,
|
|
.id = 5,
|
|
.hw_ctrld = false,
|
|
.clk_val = U300_SYSCON_SBCER_MMC_CLK_EN,
|
|
},
|
|
{
|
|
.type = U300_CLK_TYPE_FAST,
|
|
.id = 6,
|
|
.hw_ctrld = false,
|
|
.clk_val = U300_SYSCON_SBCER_SPI_CLK_EN,
|
|
},
|
|
{
|
|
.type = U300_CLK_TYPE_SLOW,
|
|
.id = 0,
|
|
.hw_ctrld = true,
|
|
.clk_val = U300_SYSCON_SBCER_SLOW_BRIDGE_CLK_EN,
|
|
},
|
|
{
|
|
.type = U300_CLK_TYPE_SLOW,
|
|
.id = 1,
|
|
.hw_ctrld = false,
|
|
.clk_val = U300_SYSCON_SBCER_UART_CLK_EN,
|
|
},
|
|
{
|
|
.type = U300_CLK_TYPE_SLOW,
|
|
.id = 4,
|
|
.hw_ctrld = false,
|
|
.clk_val = U300_SYSCON_SBCER_GPIO_CLK_EN,
|
|
},
|
|
{
|
|
.type = U300_CLK_TYPE_SLOW,
|
|
.id = 6,
|
|
.hw_ctrld = true,
|
|
/* No clock enable register bit */
|
|
.clk_val = 0xFFFFU,
|
|
},
|
|
{
|
|
.type = U300_CLK_TYPE_SLOW,
|
|
.id = 7,
|
|
.hw_ctrld = false,
|
|
.clk_val = U300_SYSCON_SBCER_APP_TMR_CLK_EN,
|
|
},
|
|
{
|
|
.type = U300_CLK_TYPE_SLOW,
|
|
.id = 8,
|
|
.hw_ctrld = false,
|
|
.clk_val = U300_SYSCON_SBCER_ACC_TMR_CLK_EN,
|
|
},
|
|
};
|
|
|
|
static void __init of_u300_syscon_clk_init(struct device_node *np)
|
|
{
|
|
struct clk *clk = ERR_PTR(-EINVAL);
|
|
const char *clk_name = np->name;
|
|
const char *parent_name;
|
|
void __iomem *res_reg;
|
|
void __iomem *en_reg;
|
|
u32 clk_type;
|
|
u32 clk_id;
|
|
int i;
|
|
|
|
if (of_property_read_u32(np, "clock-type", &clk_type)) {
|
|
pr_err("%s: syscon clock \"%s\" missing clock-type property\n",
|
|
__func__, clk_name);
|
|
return;
|
|
}
|
|
if (of_property_read_u32(np, "clock-id", &clk_id)) {
|
|
pr_err("%s: syscon clock \"%s\" missing clock-id property\n",
|
|
__func__, clk_name);
|
|
return;
|
|
}
|
|
parent_name = of_clk_get_parent_name(np, 0);
|
|
|
|
switch (clk_type) {
|
|
case U300_CLK_TYPE_SLOW:
|
|
res_reg = syscon_vbase + U300_SYSCON_RSR;
|
|
en_reg = syscon_vbase + U300_SYSCON_CESR;
|
|
break;
|
|
case U300_CLK_TYPE_FAST:
|
|
res_reg = syscon_vbase + U300_SYSCON_RFR;
|
|
en_reg = syscon_vbase + U300_SYSCON_CEFR;
|
|
break;
|
|
case U300_CLK_TYPE_REST:
|
|
res_reg = syscon_vbase + U300_SYSCON_RRR;
|
|
en_reg = syscon_vbase + U300_SYSCON_CERR;
|
|
break;
|
|
default:
|
|
pr_err("unknown clock type %x specified\n", clk_type);
|
|
return;
|
|
}
|
|
|
|
for (i = 0; i < ARRAY_SIZE(u300_clk_lookup); i++) {
|
|
const struct u300_clock *u3clk = &u300_clk_lookup[i];
|
|
|
|
if (u3clk->type == clk_type && u3clk->id == clk_id)
|
|
clk = syscon_clk_register(NULL,
|
|
clk_name, parent_name,
|
|
0, u3clk->hw_ctrld,
|
|
res_reg, u3clk->id,
|
|
en_reg, u3clk->id,
|
|
u3clk->clk_val);
|
|
}
|
|
|
|
if (!IS_ERR(clk)) {
|
|
of_clk_add_provider(np, of_clk_src_simple_get, clk);
|
|
|
|
/*
|
|
* Some few system clocks - device tree does not
|
|
* represent clocks without a corresponding device node.
|
|
* for now we add these three clocks here.
|
|
*/
|
|
if (clk_type == U300_CLK_TYPE_REST && clk_id == 5)
|
|
clk_register_clkdev(clk, NULL, "pl172");
|
|
if (clk_type == U300_CLK_TYPE_REST && clk_id == 9)
|
|
clk_register_clkdev(clk, NULL, "semi");
|
|
if (clk_type == U300_CLK_TYPE_REST && clk_id == 12)
|
|
clk_register_clkdev(clk, NULL, "intcon");
|
|
}
|
|
}
|
|
|
|
/**
|
|
* struct clk_mclk - U300 MCLK clock (MMC/SD clock)
|
|
* @hw: corresponding clock hardware entry
|
|
* @is_mspro: if this is the memory stick clock rather than MMC/SD
|
|
*/
|
|
struct clk_mclk {
|
|
struct clk_hw hw;
|
|
bool is_mspro;
|
|
};
|
|
|
|
#define to_mclk(_hw) container_of(_hw, struct clk_mclk, hw)
|
|
|
|
static int mclk_clk_prepare(struct clk_hw *hw)
|
|
{
|
|
struct clk_mclk *mclk = to_mclk(hw);
|
|
u16 val;
|
|
|
|
/* The MMC and MSPRO clocks need some special set-up */
|
|
if (!mclk->is_mspro) {
|
|
/* Set default MMC clock divisor to 18.9 MHz */
|
|
writew(0x0054U, syscon_vbase + U300_SYSCON_MMF0R);
|
|
val = readw(syscon_vbase + U300_SYSCON_MMCR);
|
|
/* Disable the MMC feedback clock */
|
|
val &= ~U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE;
|
|
/* Disable MSPRO frequency */
|
|
val &= ~U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE;
|
|
writew(val, syscon_vbase + U300_SYSCON_MMCR);
|
|
} else {
|
|
val = readw(syscon_vbase + U300_SYSCON_MMCR);
|
|
/* Disable the MMC feedback clock */
|
|
val &= ~U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE;
|
|
/* Enable MSPRO frequency */
|
|
val |= U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE;
|
|
writew(val, syscon_vbase + U300_SYSCON_MMCR);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static unsigned long
|
|
mclk_clk_recalc_rate(struct clk_hw *hw,
|
|
unsigned long parent_rate)
|
|
{
|
|
u16 perf = syscon_get_perf();
|
|
|
|
switch (perf) {
|
|
case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
|
|
/*
|
|
* Here, the 208 MHz PLL gets shut down and the always
|
|
* on 13 MHz PLL used for RTC etc kicks into use
|
|
* instead.
|
|
*/
|
|
return 13000000;
|
|
case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
|
|
case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
|
|
case U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH:
|
|
case U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST:
|
|
{
|
|
/*
|
|
* This clock is under program control. The register is
|
|
* divided in two nybbles, bit 7-4 gives cycles-1 to count
|
|
* high, bit 3-0 gives cycles-1 to count low. Distribute
|
|
* these with no more than 1 cycle difference between
|
|
* low and high and add low and high to get the actual
|
|
* divisor. The base PLL is 208 MHz. Writing 0x00 will
|
|
* divide by 1 and 1 so the highest frequency possible
|
|
* is 104 MHz.
|
|
*
|
|
* e.g. 0x54 =>
|
|
* f = 208 / ((5+1) + (4+1)) = 208 / 11 = 18.9 MHz
|
|
*/
|
|
u16 val = readw(syscon_vbase + U300_SYSCON_MMF0R) &
|
|
U300_SYSCON_MMF0R_MASK;
|
|
switch (val) {
|
|
case 0x0054:
|
|
return 18900000;
|
|
case 0x0044:
|
|
return 20800000;
|
|
case 0x0043:
|
|
return 23100000;
|
|
case 0x0033:
|
|
return 26000000;
|
|
case 0x0032:
|
|
return 29700000;
|
|
case 0x0022:
|
|
return 34700000;
|
|
case 0x0021:
|
|
return 41600000;
|
|
case 0x0011:
|
|
return 52000000;
|
|
case 0x0000:
|
|
return 104000000;
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
default:
|
|
break;
|
|
}
|
|
return parent_rate;
|
|
}
|
|
|
|
static long
|
|
mclk_clk_round_rate(struct clk_hw *hw, unsigned long rate,
|
|
unsigned long *prate)
|
|
{
|
|
if (rate <= 18900000)
|
|
return 18900000;
|
|
if (rate <= 20800000)
|
|
return 20800000;
|
|
if (rate <= 23100000)
|
|
return 23100000;
|
|
if (rate <= 26000000)
|
|
return 26000000;
|
|
if (rate <= 29700000)
|
|
return 29700000;
|
|
if (rate <= 34700000)
|
|
return 34700000;
|
|
if (rate <= 41600000)
|
|
return 41600000;
|
|
/* Highest rate */
|
|
return 52000000;
|
|
}
|
|
|
|
static int mclk_clk_set_rate(struct clk_hw *hw, unsigned long rate,
|
|
unsigned long parent_rate)
|
|
{
|
|
u16 val;
|
|
u16 reg;
|
|
|
|
switch (rate) {
|
|
case 18900000:
|
|
val = 0x0054;
|
|
break;
|
|
case 20800000:
|
|
val = 0x0044;
|
|
break;
|
|
case 23100000:
|
|
val = 0x0043;
|
|
break;
|
|
case 26000000:
|
|
val = 0x0033;
|
|
break;
|
|
case 29700000:
|
|
val = 0x0032;
|
|
break;
|
|
case 34700000:
|
|
val = 0x0022;
|
|
break;
|
|
case 41600000:
|
|
val = 0x0021;
|
|
break;
|
|
case 52000000:
|
|
val = 0x0011;
|
|
break;
|
|
case 104000000:
|
|
val = 0x0000;
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
|
|
reg = readw(syscon_vbase + U300_SYSCON_MMF0R) &
|
|
~U300_SYSCON_MMF0R_MASK;
|
|
writew(reg | val, syscon_vbase + U300_SYSCON_MMF0R);
|
|
return 0;
|
|
}
|
|
|
|
static const struct clk_ops mclk_ops = {
|
|
.prepare = mclk_clk_prepare,
|
|
.recalc_rate = mclk_clk_recalc_rate,
|
|
.round_rate = mclk_clk_round_rate,
|
|
.set_rate = mclk_clk_set_rate,
|
|
};
|
|
|
|
static struct clk * __init
|
|
mclk_clk_register(struct device *dev, const char *name,
|
|
const char *parent_name, bool is_mspro)
|
|
{
|
|
struct clk *clk;
|
|
struct clk_mclk *mclk;
|
|
struct clk_init_data init;
|
|
|
|
mclk = kzalloc(sizeof(struct clk_mclk), GFP_KERNEL);
|
|
if (!mclk) {
|
|
pr_err("could not allocate MMC/SD clock %s\n",
|
|
name);
|
|
return ERR_PTR(-ENOMEM);
|
|
}
|
|
init.name = "mclk";
|
|
init.ops = &mclk_ops;
|
|
init.flags = 0;
|
|
init.parent_names = (parent_name ? &parent_name : NULL);
|
|
init.num_parents = (parent_name ? 1 : 0);
|
|
mclk->hw.init = &init;
|
|
mclk->is_mspro = is_mspro;
|
|
|
|
clk = clk_register(dev, &mclk->hw);
|
|
if (IS_ERR(clk))
|
|
kfree(mclk);
|
|
|
|
return clk;
|
|
}
|
|
|
|
static void __init of_u300_syscon_mclk_init(struct device_node *np)
|
|
{
|
|
struct clk *clk = ERR_PTR(-EINVAL);
|
|
const char *clk_name = np->name;
|
|
const char *parent_name;
|
|
|
|
parent_name = of_clk_get_parent_name(np, 0);
|
|
clk = mclk_clk_register(NULL, clk_name, parent_name, false);
|
|
if (!IS_ERR(clk))
|
|
of_clk_add_provider(np, of_clk_src_simple_get, clk);
|
|
}
|
|
|
|
static const struct of_device_id u300_clk_match[] __initconst = {
|
|
{
|
|
.compatible = "fixed-clock",
|
|
.data = of_fixed_clk_setup,
|
|
},
|
|
{
|
|
.compatible = "fixed-factor-clock",
|
|
.data = of_fixed_factor_clk_setup,
|
|
},
|
|
{
|
|
.compatible = "stericsson,u300-syscon-clk",
|
|
.data = of_u300_syscon_clk_init,
|
|
},
|
|
{
|
|
.compatible = "stericsson,u300-syscon-mclk",
|
|
.data = of_u300_syscon_mclk_init,
|
|
},
|
|
};
|
|
|
|
|
|
void __init u300_clk_init(void __iomem *base)
|
|
{
|
|
u16 val;
|
|
|
|
syscon_vbase = base;
|
|
|
|
/* Set system to run at PLL208, max performance, a known state. */
|
|
val = readw(syscon_vbase + U300_SYSCON_CCR);
|
|
val &= ~U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK;
|
|
writew(val, syscon_vbase + U300_SYSCON_CCR);
|
|
/* Wait for the PLL208 to lock if not locked in yet */
|
|
while (!(readw(syscon_vbase + U300_SYSCON_CSR) &
|
|
U300_SYSCON_CSR_PLL208_LOCK_IND));
|
|
|
|
/* Power management enable */
|
|
val = readw(syscon_vbase + U300_SYSCON_PMCR);
|
|
val |= U300_SYSCON_PMCR_PWR_MGNT_ENABLE;
|
|
writew(val, syscon_vbase + U300_SYSCON_PMCR);
|
|
|
|
of_clk_init(u300_clk_match);
|
|
}
|