mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-21 10:05:00 +08:00
26b78c81e8
The hardware bug in POWER9 preventing use of the DAWR was fixed in DD2.3. Set the CPU_FTR_DAWR feature bit on these newer systems to start using it again, and update the documentation accordingly. The CPU features for DD2.3 are currently determined by "DD2.2 or later" logic. In adding DD2.3 as a discrete case for the first time here, I'm carrying the quirks of DD2.2 forward to keep all behavior outside of this DAWR change the same. This leaves the assessment and potential removal of those quirks on DD2.3 for later. Signed-off-by: Reza Arbab <arbab@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220503170152.23412-1-arbab@linux.ibm.com
102 lines
3.6 KiB
ReStructuredText
102 lines
3.6 KiB
ReStructuredText
=====================
|
|
DAWR issues on POWER9
|
|
=====================
|
|
|
|
On older POWER9 processors, the Data Address Watchpoint Register (DAWR) can
|
|
cause a checkstop if it points to cache inhibited (CI) memory. Currently Linux
|
|
has no way to distinguish CI memory when configuring the DAWR, so on affected
|
|
systems, the DAWR is disabled.
|
|
|
|
Affected processor revisions
|
|
============================
|
|
|
|
This issue is only present on processors prior to v2.3. The revision can be
|
|
found in /proc/cpuinfo::
|
|
|
|
processor : 0
|
|
cpu : POWER9, altivec supported
|
|
clock : 3800.000000MHz
|
|
revision : 2.3 (pvr 004e 1203)
|
|
|
|
On a system with the issue, the DAWR is disabled as detailed below.
|
|
|
|
Technical Details:
|
|
==================
|
|
|
|
DAWR has 6 different ways of being set.
|
|
1) ptrace
|
|
2) h_set_mode(DAWR)
|
|
3) h_set_dabr()
|
|
4) kvmppc_set_one_reg()
|
|
5) xmon
|
|
|
|
For ptrace, we now advertise zero breakpoints on POWER9 via the
|
|
PPC_PTRACE_GETHWDBGINFO call. This results in GDB falling back to
|
|
software emulation of the watchpoint (which is slow).
|
|
|
|
h_set_mode(DAWR) and h_set_dabr() will now return an error to the
|
|
guest on a POWER9 host. Current Linux guests ignore this error, so
|
|
they will silently not get the DAWR.
|
|
|
|
kvmppc_set_one_reg() will store the value in the vcpu but won't
|
|
actually set it on POWER9 hardware. This is done so we don't break
|
|
migration from POWER8 to POWER9, at the cost of silently losing the
|
|
DAWR on the migration.
|
|
|
|
For xmon, the 'bd' command will return an error on P9.
|
|
|
|
Consequences for users
|
|
======================
|
|
|
|
For GDB watchpoints (ie 'watch' command) on POWER9 bare metal , GDB
|
|
will accept the command. Unfortunately since there is no hardware
|
|
support for the watchpoint, GDB will software emulate the watchpoint
|
|
making it run very slowly.
|
|
|
|
The same will also be true for any guests started on a POWER9
|
|
host. The watchpoint will fail and GDB will fall back to software
|
|
emulation.
|
|
|
|
If a guest is started on a POWER8 host, GDB will accept the watchpoint
|
|
and configure the hardware to use the DAWR. This will run at full
|
|
speed since it can use the hardware emulation. Unfortunately if this
|
|
guest is migrated to a POWER9 host, the watchpoint will be lost on the
|
|
POWER9. Loads and stores to the watchpoint locations will not be
|
|
trapped in GDB. The watchpoint is remembered, so if the guest is
|
|
migrated back to the POWER8 host, it will start working again.
|
|
|
|
Force enabling the DAWR
|
|
=======================
|
|
Kernels (since ~v5.2) have an option to force enable the DAWR via::
|
|
|
|
echo Y > /sys/kernel/debug/powerpc/dawr_enable_dangerous
|
|
|
|
This enables the DAWR even on POWER9.
|
|
|
|
This is a dangerous setting, USE AT YOUR OWN RISK.
|
|
|
|
Some users may not care about a bad user crashing their box
|
|
(ie. single user/desktop systems) and really want the DAWR. This
|
|
allows them to force enable DAWR.
|
|
|
|
This flag can also be used to disable DAWR access. Once this is
|
|
cleared, all DAWR access should be cleared immediately and your
|
|
machine once again safe from crashing.
|
|
|
|
Userspace may get confused by toggling this. If DAWR is force
|
|
enabled/disabled between getting the number of breakpoints (via
|
|
PTRACE_GETHWDBGINFO) and setting the breakpoint, userspace will get an
|
|
inconsistent view of what's available. Similarly for guests.
|
|
|
|
For the DAWR to be enabled in a KVM guest, the DAWR needs to be force
|
|
enabled in the host AND the guest. For this reason, this won't work on
|
|
POWERVM as it doesn't allow the HCALL to work. Writes of 'Y' to the
|
|
dawr_enable_dangerous file will fail if the hypervisor doesn't support
|
|
writing the DAWR.
|
|
|
|
To double check the DAWR is working, run this kernel selftest:
|
|
|
|
tools/testing/selftests/powerpc/ptrace/ptrace-hwbreak.c
|
|
|
|
Any errors/failures/skips mean something is wrong.
|