mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-15 23:14:31 +08:00
238 lines
6.4 KiB
C
238 lines
6.4 KiB
C
/*
|
|
* linux/include/asm-arm/arch-clps711x/hardware.h
|
|
*
|
|
* This file contains the hardware definitions of the Prospector P720T.
|
|
*
|
|
* Copyright (C) 2000 Deep Blue Solutions Ltd.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
|
|
*/
|
|
#ifndef __ASM_ARCH_HARDWARE_H
|
|
#define __ASM_ARCH_HARDWARE_H
|
|
|
|
|
|
#define CLPS7111_VIRT_BASE 0xff000000
|
|
#define CLPS7111_BASE CLPS7111_VIRT_BASE
|
|
|
|
/*
|
|
* The physical addresses that the external chip select signals map to is
|
|
* dependent on the setting of the nMEDCHG signal on EP7211 and EP7212
|
|
* processors. CONFIG_EP72XX_BOOT_ROM is only available if these
|
|
* processors are in use.
|
|
*/
|
|
#ifndef CONFIG_EP72XX_ROM_BOOT
|
|
#define CS0_PHYS_BASE (0x00000000)
|
|
#define CS1_PHYS_BASE (0x10000000)
|
|
#define CS2_PHYS_BASE (0x20000000)
|
|
#define CS3_PHYS_BASE (0x30000000)
|
|
#define CS4_PHYS_BASE (0x40000000)
|
|
#define CS5_PHYS_BASE (0x50000000)
|
|
#define CS6_PHYS_BASE (0x60000000)
|
|
#define CS7_PHYS_BASE (0x70000000)
|
|
#else
|
|
#define CS0_PHYS_BASE (0x70000000)
|
|
#define CS1_PHYS_BASE (0x60000000)
|
|
#define CS2_PHYS_BASE (0x50000000)
|
|
#define CS3_PHYS_BASE (0x40000000)
|
|
#define CS4_PHYS_BASE (0x30000000)
|
|
#define CS5_PHYS_BASE (0x20000000)
|
|
#define CS6_PHYS_BASE (0x10000000)
|
|
#define CS7_PHYS_BASE (0x00000000)
|
|
#endif
|
|
|
|
#if defined (CONFIG_ARCH_EP7211)
|
|
|
|
#define EP7211_VIRT_BASE CLPS7111_VIRT_BASE
|
|
#define EP7211_BASE CLPS7111_VIRT_BASE
|
|
#include <asm/hardware/ep7211.h>
|
|
|
|
#elif defined (CONFIG_ARCH_EP7212)
|
|
|
|
#define EP7212_VIRT_BASE CLPS7111_VIRT_BASE
|
|
#define EP7212_BASE CLPS7111_VIRT_BASE
|
|
#include <asm/hardware/ep7212.h>
|
|
|
|
#endif
|
|
|
|
#define SYSPLD_VIRT_BASE 0xfe000000
|
|
#define SYSPLD_BASE SYSPLD_VIRT_BASE
|
|
|
|
#ifndef __ASSEMBLER__
|
|
|
|
#define PCIO_BASE IO_BASE
|
|
|
|
#endif
|
|
|
|
|
|
#if defined (CONFIG_ARCH_AUTCPU12)
|
|
|
|
#define CS89712_VIRT_BASE CLPS7111_VIRT_BASE
|
|
#define CS89712_BASE CLPS7111_VIRT_BASE
|
|
|
|
#include <asm/hardware/clps7111.h>
|
|
#include <asm/hardware/ep7212.h>
|
|
#include <asm/hardware/cs89712.h>
|
|
|
|
#endif
|
|
|
|
|
|
#if defined (CONFIG_ARCH_CDB89712)
|
|
|
|
#include <asm/hardware/clps7111.h>
|
|
#include <asm/hardware/ep7212.h>
|
|
#include <asm/hardware/cs89712.h>
|
|
|
|
/* dynamic ioremap() areas */
|
|
#define FLASH_START 0x00000000
|
|
#define FLASH_SIZE 0x800000
|
|
#define FLASH_WIDTH 4
|
|
|
|
#define SRAM_START 0x60000000
|
|
#define SRAM_SIZE 0xc000
|
|
#define SRAM_WIDTH 4
|
|
|
|
#define BOOTROM_START 0x70000000
|
|
#define BOOTROM_SIZE 0x80
|
|
#define BOOTROM_WIDTH 4
|
|
|
|
|
|
/* static cdb89712_map_io() areas */
|
|
#define REGISTER_START 0x80000000
|
|
#define REGISTER_SIZE 0x4000
|
|
#define REGISTER_BASE 0xff000000
|
|
|
|
#define ETHER_START 0x20000000
|
|
#define ETHER_SIZE 0x1000
|
|
#define ETHER_BASE 0xfe000000
|
|
|
|
#endif
|
|
|
|
|
|
#if defined (CONFIG_ARCH_EDB7211)
|
|
|
|
/*
|
|
* The extra 8 lines of the keyboard matrix are wired to chip select 3 (nCS3)
|
|
* and repeat across it. This is the mapping for it.
|
|
*
|
|
* In jumpered boot mode, nCS3 is mapped to 0x4000000, not 0x3000000. This
|
|
* was cause for much consternation and headscratching. This should probably
|
|
* be made a compile/run time kernel option.
|
|
*/
|
|
#define EP7211_PHYS_EXTKBD CS3_PHYS_BASE /* physical */
|
|
|
|
#define EP7211_VIRT_EXTKBD (0xfd000000) /* virtual */
|
|
|
|
|
|
/*
|
|
* The CS8900A ethernet chip has its I/O registers wired to chip select 2
|
|
* (nCS2). This is the mapping for it.
|
|
*
|
|
* In jumpered boot mode, nCS2 is mapped to 0x5000000, not 0x2000000. This
|
|
* was cause for much consternation and headscratching. This should probably
|
|
* be made a compile/run time kernel option.
|
|
*/
|
|
#define EP7211_PHYS_CS8900A CS2_PHYS_BASE /* physical */
|
|
|
|
#define EP7211_VIRT_CS8900A (0xfc000000) /* virtual */
|
|
|
|
|
|
/*
|
|
* The two flash banks are wired to chip selects 0 and 1. This is the mapping
|
|
* for them.
|
|
*
|
|
* nCS0 and nCS1 are at 0x70000000 and 0x60000000, respectively, when running
|
|
* in jumpered boot mode.
|
|
*/
|
|
#define EP7211_PHYS_FLASH1 CS0_PHYS_BASE /* physical */
|
|
#define EP7211_PHYS_FLASH2 CS1_PHYS_BASE /* physical */
|
|
|
|
#define EP7211_VIRT_FLASH1 (0xfa000000) /* virtual */
|
|
#define EP7211_VIRT_FLASH2 (0xfb000000) /* virtual */
|
|
|
|
#endif /* CONFIG_ARCH_EDB7211 */
|
|
|
|
|
|
/*
|
|
* Relevant bits in port D, which controls power to the various parts of
|
|
* the LCD on the EDB7211.
|
|
*/
|
|
#define EDB_PD1_LCD_DC_DC_EN (1<<1)
|
|
#define EDB_PD2_LCDEN (1<<2)
|
|
#define EDB_PD3_LCDBL (1<<3)
|
|
|
|
|
|
#if defined (CONFIG_ARCH_CEIVA)
|
|
|
|
#define CEIVA_VIRT_BASE CLPS7111_VIRT_BASE
|
|
#define CEIVA_BASE CLPS7111_VIRT_BASE
|
|
|
|
#include <asm/hardware/clps7111.h>
|
|
#include <asm/hardware/ep7212.h>
|
|
|
|
|
|
/*
|
|
* The two flash banks are wired to chip selects 0 and 1. This is the mapping
|
|
* for them.
|
|
*
|
|
* nCS0 and nCS1 are at 0x70000000 and 0x60000000, respectively, when running
|
|
* in jumpered boot mode.
|
|
*/
|
|
#define CEIVA_PHYS_FLASH1 CS0_PHYS_BASE /* physical */
|
|
#define CEIVA_PHYS_FLASH2 CS1_PHYS_BASE /* physical */
|
|
|
|
#define CEIVA_VIRT_FLASH1 (0xfa000000) /* virtual */
|
|
#define CEIVA_VIRT_FLASH2 (0xfb000000) /* virtual */
|
|
|
|
#define CEIVA_FLASH_SIZE 0x100000
|
|
#define CEIVA_FLASH_WIDTH 2
|
|
|
|
#define SRAM_START 0x60000000
|
|
#define SRAM_SIZE 0xc000
|
|
#define SRAM_WIDTH 4
|
|
|
|
#define BOOTROM_START 0x70000000
|
|
#define BOOTROM_SIZE 0x80
|
|
#define BOOTROM_WIDTH 4
|
|
|
|
/*
|
|
* SED1355 LCD controller
|
|
*/
|
|
#define CEIVA_PHYS_SED1355 CS2_PHYS_BASE
|
|
#define CEIVA_VIRT_SED1355 (0xfc000000)
|
|
|
|
/*
|
|
* Relevant bits in port D, which controls power to the various parts of
|
|
* the LCD on the Ceiva Photo Max, and reset to the LCD controller.
|
|
*/
|
|
|
|
// Reset line to SED1355 (must be high to operate)
|
|
#define CEIVA_PD1_LCDRST (1<<1)
|
|
// LCD panel enable (set to one, to enable LCD)
|
|
#define CEIVA_PD4_LCDEN (1<<4)
|
|
// Backlight (set to one, to turn on backlight
|
|
#define CEIVA_PD5_LCDBL (1<<5)
|
|
|
|
/*
|
|
* Relevant bits in port B, which report the status of the buttons.
|
|
*/
|
|
|
|
// White button
|
|
#define CEIVA_PB4_WHT_BTN (1<<4)
|
|
// Black button
|
|
#define CEIVA_PB0_BLK_BTN (1<<0)
|
|
#endif // #if defined (CONFIG_ARCH_CEIVA)
|
|
|
|
#endif
|