mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-24 19:45:06 +08:00
c9a0ef5528
Add interrupt controller properties now that spmi-gpio is a proper hierarchical IRQ chip. The interrupts property is no longer needed so remove it. This change was not tested on any hardware but the same change was tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with no issues. Signed-off-by: Brian Masney <masneyb@onstation.org> Reviewed-by: Stephen Boyd <sboyd@kernel.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
100 lines
2.2 KiB
Plaintext
100 lines
2.2 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
#include <dt-bindings/iio/qcom,spmi-vadc.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/spmi/spmi.h>
|
|
|
|
&spmi_bus {
|
|
|
|
pma8084_0: pma8084@0 {
|
|
compatible = "qcom,pma8084", "qcom,spmi-pmic";
|
|
reg = <0x0 SPMI_USID>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
rtc@6000 {
|
|
compatible = "qcom,pm8941-rtc";
|
|
reg = <0x6000>,
|
|
<0x6100>;
|
|
reg-names = "rtc", "alarm";
|
|
interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
|
|
};
|
|
|
|
pwrkey@800 {
|
|
compatible = "qcom,pm8941-pwrkey";
|
|
reg = <0x800>;
|
|
interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
|
|
debounce = <15625>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
pma8084_gpios: gpios@c000 {
|
|
compatible = "qcom,pma8084-gpio", "qcom,spmi-gpio";
|
|
reg = <0xc000>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
pma8084_mpps: mpps@a000 {
|
|
compatible = "qcom,pma8084-mpp", "qcom,spmi-mpp";
|
|
reg = <0xa000>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupts = <0 0xa0 0 IRQ_TYPE_NONE>,
|
|
<0 0xa1 0 IRQ_TYPE_NONE>,
|
|
<0 0xa2 0 IRQ_TYPE_NONE>,
|
|
<0 0xa3 0 IRQ_TYPE_NONE>,
|
|
<0 0xa4 0 IRQ_TYPE_NONE>,
|
|
<0 0xa5 0 IRQ_TYPE_NONE>,
|
|
<0 0xa6 0 IRQ_TYPE_NONE>,
|
|
<0 0xa7 0 IRQ_TYPE_NONE>;
|
|
};
|
|
|
|
pma8084_temp: temp-alarm@2400 {
|
|
compatible = "qcom,spmi-temp-alarm";
|
|
reg = <0x2400>;
|
|
interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
|
|
#thermal-sensor-cells = <0>;
|
|
io-channels = <&pma8084_vadc VADC_DIE_TEMP>;
|
|
io-channel-names = "thermal";
|
|
};
|
|
|
|
pma8084_vadc: vadc@3100 {
|
|
compatible = "qcom,spmi-vadc";
|
|
reg = <0x3100>;
|
|
interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
#io-channel-cells = <1>;
|
|
io-channel-ranges;
|
|
|
|
die_temp {
|
|
reg = <VADC_DIE_TEMP>;
|
|
};
|
|
ref_625mv {
|
|
reg = <VADC_REF_625MV>;
|
|
};
|
|
ref_1250v {
|
|
reg = <VADC_REF_1250MV>;
|
|
};
|
|
ref_buf_625mv {
|
|
reg = <VADC_SPARE1>;
|
|
};
|
|
ref_gnd {
|
|
reg = <VADC_GND_REF>;
|
|
};
|
|
ref_vdd {
|
|
reg = <VADC_VDD_VADC>;
|
|
};
|
|
};
|
|
};
|
|
|
|
pma8084_1: pma8084@1 {
|
|
compatible = "qcom,pma8084", "qcom,spmi-pmic";
|
|
reg = <0x1 SPMI_USID>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
};
|
|
};
|