linux/drivers/pinctrl/qcom/pinctrl-msm.h
Lina Iyer e35a6ae0eb pinctrl/msm: Setup GPIO chip in hierarchy
Some GPIOs are marked as wakeup capable and are routed to another
interrupt controller that is an always-domain and can detect interrupts
even when most of the SoC is powered off. The wakeup interrupt
controller wakes up the GIC and replays the interrupt at the GIC.

Setup the TLMM irqchip in hierarchy with the wakeup interrupt controller
and ensure the wakeup GPIOs are handled correctly.

Co-developed-by: Maulik Shah <mkshah@codeaurora.org>

Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1573855915-9841-9-git-send-email-ilina@codeaurora.org

----
Changes in v2:
	- Address review comments
	- Fix Co-developed-by tag
Changes in v1:
	- Address minor review comments
	- Remove redundant call to set irq handler
	- Move irq_domain_qcom_handle_wakeup() to this patch
Changes in RFC v2:
	- Rebase on top of GPIO hierarchy support in linux-next
	- Set the chained irq handler for summary line
2019-11-16 10:23:15 +00:00

140 lines
5.1 KiB
C

/* SPDX-License-Identifier: GPL-2.0-only */
/*
* Copyright (c) 2013, Sony Mobile Communications AB.
*/
#ifndef __PINCTRL_MSM_H__
#define __PINCTRL_MSM_H__
struct pinctrl_pin_desc;
/**
* struct msm_function - a pinmux function
* @name: Name of the pinmux function.
* @groups: List of pingroups for this function.
* @ngroups: Number of entries in @groups.
*/
struct msm_function {
const char *name;
const char * const *groups;
unsigned ngroups;
};
/**
* struct msm_pingroup - Qualcomm pingroup definition
* @name: Name of the pingroup.
* @pins: A list of pins assigned to this pingroup.
* @npins: Number of entries in @pins.
* @funcs: A list of pinmux functions that can be selected for
* this group. The index of the selected function is used
* for programming the function selector.
* Entries should be indices into the groups list of the
* struct msm_pinctrl_soc_data.
* @ctl_reg: Offset of the register holding control bits for this group.
* @io_reg: Offset of the register holding input/output bits for this group.
* @intr_cfg_reg: Offset of the register holding interrupt configuration bits.
* @intr_status_reg: Offset of the register holding the status bits for this group.
* @intr_target_reg: Offset of the register specifying routing of the interrupts
* from this group.
* @mux_bit: Offset in @ctl_reg for the pinmux function selection.
* @pull_bit: Offset in @ctl_reg for the bias configuration.
* @drv_bit: Offset in @ctl_reg for the drive strength configuration.
* @oe_bit: Offset in @ctl_reg for controlling output enable.
* @in_bit: Offset in @io_reg for the input bit value.
* @out_bit: Offset in @io_reg for the output bit value.
* @intr_enable_bit: Offset in @intr_cfg_reg for enabling the interrupt for this group.
* @intr_status_bit: Offset in @intr_status_reg for reading and acking the interrupt
* status.
* @intr_target_bit: Offset in @intr_target_reg for configuring the interrupt routing.
* @intr_target_kpss_val: Value in @intr_target_bit for specifying that the interrupt from
* this gpio should get routed to the KPSS processor.
* @intr_raw_status_bit: Offset in @intr_cfg_reg for the raw status bit.
* @intr_polarity_bit: Offset in @intr_cfg_reg for specifying polarity of the interrupt.
* @intr_detection_bit: Offset in @intr_cfg_reg for specifying interrupt type.
* @intr_detection_width: Number of bits used for specifying interrupt type,
* Should be 2 for SoCs that can detect both edges in hardware,
* otherwise 1.
*/
struct msm_pingroup {
const char *name;
const unsigned *pins;
unsigned npins;
unsigned *funcs;
unsigned nfuncs;
u32 ctl_reg;
u32 io_reg;
u32 intr_cfg_reg;
u32 intr_status_reg;
u32 intr_target_reg;
unsigned int tile:2;
unsigned mux_bit:5;
unsigned pull_bit:5;
unsigned drv_bit:5;
unsigned oe_bit:5;
unsigned in_bit:5;
unsigned out_bit:5;
unsigned intr_enable_bit:5;
unsigned intr_status_bit:5;
unsigned intr_ack_high:1;
unsigned intr_target_bit:5;
unsigned intr_target_kpss_val:5;
unsigned intr_raw_status_bit:5;
unsigned intr_polarity_bit:5;
unsigned intr_detection_bit:5;
unsigned intr_detection_width:5;
};
/**
* struct msm_gpio_wakeirq_map - Map of GPIOs and their wakeup pins
* @gpio: The GPIOs that are wakeup capable
* @wakeirq: The interrupt at the always-on interrupt controller
*/
struct msm_gpio_wakeirq_map {
unsigned int gpio;
unsigned int wakeirq;
};
/**
* struct msm_pinctrl_soc_data - Qualcomm pin controller driver configuration
* @pins: An array describing all pins the pin controller affects.
* @npins: The number of entries in @pins.
* @functions: An array describing all mux functions the SoC supports.
* @nfunctions: The number of entries in @functions.
* @groups: An array describing all pin groups the pin SoC supports.
* @ngroups: The numbmer of entries in @groups.
* @ngpio: The number of pingroups the driver should expose as GPIOs.
* @pull_no_keeper: The SoC does not support keeper bias.
* @wakeirq_map: The map of wakeup capable GPIOs and the pin at PDC/MPM
* @nwakeirq_map: The number of entries in @wakeirq_map
*/
struct msm_pinctrl_soc_data {
const struct pinctrl_pin_desc *pins;
unsigned npins;
const struct msm_function *functions;
unsigned nfunctions;
const struct msm_pingroup *groups;
unsigned ngroups;
unsigned ngpios;
bool pull_no_keeper;
const char *const *tiles;
unsigned int ntiles;
const int *reserved_gpios;
const struct msm_gpio_wakeirq_map *wakeirq_map;
unsigned int nwakeirq_map;
};
extern const struct dev_pm_ops msm_pinctrl_dev_pm_ops;
int msm_pinctrl_probe(struct platform_device *pdev,
const struct msm_pinctrl_soc_data *soc_data);
int msm_pinctrl_remove(struct platform_device *pdev);
#endif