mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-19 18:24:14 +08:00
33f810b203
Move the FDDI drivers into drivers/net/fddi/ and make the necessary Kconfig and Makefile changes. CC: "Maciej W. Rozycki" <macro@linux-mips.org> CC: Christoph Goos <cgoos@syskonnect.de> CC: <linux@syskonnect.de> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
78 lines
2.4 KiB
Plaintext
78 lines
2.4 KiB
Plaintext
#
|
|
# FDDI network device configuration
|
|
#
|
|
|
|
config FDDI
|
|
tristate "FDDI driver support"
|
|
depends on PCI || EISA || TC
|
|
---help---
|
|
Fiber Distributed Data Interface is a high speed local area network
|
|
design; essentially a replacement for high speed Ethernet. FDDI can
|
|
run over copper or fiber. If you are connected to such a network and
|
|
want a driver for the FDDI card in your computer, say Y here (and
|
|
then also Y to the driver for your FDDI card, below). Most people
|
|
will say N.
|
|
|
|
if FDDI
|
|
|
|
config DEFXX
|
|
tristate "Digital DEFTA/DEFEA/DEFPA adapter support"
|
|
depends on FDDI && (PCI || EISA || TC)
|
|
---help---
|
|
This is support for the DIGITAL series of TURBOchannel (DEFTA),
|
|
EISA (DEFEA) and PCI (DEFPA) controllers which can connect you
|
|
to a local FDDI network.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called defxx. If unsure, say N.
|
|
|
|
config DEFXX_MMIO
|
|
bool
|
|
prompt "Use MMIO instead of PIO" if PCI || EISA
|
|
depends on DEFXX
|
|
default n if PCI || EISA
|
|
default y
|
|
---help---
|
|
This instructs the driver to use EISA or PCI memory-mapped I/O
|
|
(MMIO) as appropriate instead of programmed I/O ports (PIO).
|
|
Enabling this gives an improvement in processing time in parts
|
|
of the driver, but it may cause problems with EISA (DEFEA)
|
|
adapters. TURBOchannel does not have the concept of I/O ports,
|
|
so MMIO is always used for these (DEFTA) adapters.
|
|
|
|
If unsure, say N.
|
|
|
|
config SKFP
|
|
tristate "SysKonnect FDDI PCI support"
|
|
depends on FDDI && PCI
|
|
select BITREVERSE
|
|
---help---
|
|
Say Y here if you have a SysKonnect FDDI PCI adapter.
|
|
The following adapters are supported by this driver:
|
|
- SK-5521 (SK-NET FDDI-UP)
|
|
- SK-5522 (SK-NET FDDI-UP DAS)
|
|
- SK-5541 (SK-NET FDDI-FP)
|
|
- SK-5543 (SK-NET FDDI-LP)
|
|
- SK-5544 (SK-NET FDDI-LP DAS)
|
|
- SK-5821 (SK-NET FDDI-UP64)
|
|
- SK-5822 (SK-NET FDDI-UP64 DAS)
|
|
- SK-5841 (SK-NET FDDI-FP64)
|
|
- SK-5843 (SK-NET FDDI-LP64)
|
|
- SK-5844 (SK-NET FDDI-LP64 DAS)
|
|
- Netelligent 100 FDDI DAS Fibre SC
|
|
- Netelligent 100 FDDI SAS Fibre SC
|
|
- Netelligent 100 FDDI DAS UTP
|
|
- Netelligent 100 FDDI SAS UTP
|
|
- Netelligent 100 FDDI SAS Fibre MIC
|
|
|
|
Read <file:Documentation/networking/skfp.txt> for information about
|
|
the driver.
|
|
|
|
Questions concerning this driver can be addressed to:
|
|
<linux@syskonnect.de>
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called skfp. This is recommended.
|
|
|
|
endif # FDDI
|