mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-23 20:24:12 +08:00
95691e3edd
Currently, "disable_clkrun" yenta_socket module parameter is only implemented for TI CardBus bridges. Add also an implementation for Ricoh bridges that have the necessary setting documented in publicly available datasheets. Tested on a RL5C476II with a Sunrich C-160 CardBus NIC that doesn't work correctly unless the CLKRUN protocol is disabled. Let's also make it clear in its description that the "disable_clkrun" module parameter only works on these two previously mentioned brands of CardBus bridges. Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Cc: stable@vger.kernel.org Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
242 lines
7.6 KiB
C
242 lines
7.6 KiB
C
/*
|
|
* ricoh.h 1.9 1999/10/25 20:03:34
|
|
*
|
|
* The contents of this file are subject to the Mozilla Public License
|
|
* Version 1.1 (the "License"); you may not use this file except in
|
|
* compliance with the License. You may obtain a copy of the License
|
|
* at http://www.mozilla.org/MPL/
|
|
*
|
|
* Software distributed under the License is distributed on an "AS IS"
|
|
* basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
|
|
* the License for the specific language governing rights and
|
|
* limitations under the License.
|
|
*
|
|
* The initial developer of the original code is David A. Hinds
|
|
* <dahinds@users.sourceforge.net>. Portions created by David A. Hinds
|
|
* are Copyright (C) 1999 David A. Hinds. All Rights Reserved.
|
|
*
|
|
* Alternatively, the contents of this file may be used under the
|
|
* terms of the GNU General Public License version 2 (the "GPL"), in which
|
|
* case the provisions of the GPL are applicable instead of the
|
|
* above. If you wish to allow the use of your version of this file
|
|
* only under the terms of the GPL and not to allow others to use
|
|
* your version of this file under the MPL, indicate your decision by
|
|
* deleting the provisions above and replace them with the notice and
|
|
* other provisions required by the GPL. If you do not delete the
|
|
* provisions above, a recipient may use your version of this file
|
|
* under either the MPL or the GPL.
|
|
*/
|
|
|
|
#ifndef _LINUX_RICOH_H
|
|
#define _LINUX_RICOH_H
|
|
|
|
|
|
#define RF5C_MODE_CTL 0x1f /* Mode control */
|
|
#define RF5C_PWR_CTL 0x2f /* Mixed voltage control */
|
|
#define RF5C_CHIP_ID 0x3a /* Chip identification */
|
|
#define RF5C_MODE_CTL_3 0x3b /* Mode control 3 */
|
|
|
|
/* I/O window address offset */
|
|
#define RF5C_IO_OFF(w) (0x36+((w)<<1))
|
|
|
|
/* Flags for RF5C_MODE_CTL */
|
|
#define RF5C_MODE_ATA 0x01 /* ATA mode */
|
|
#define RF5C_MODE_LED_ENA 0x02 /* IRQ 12 is LED */
|
|
#define RF5C_MODE_CA21 0x04
|
|
#define RF5C_MODE_CA22 0x08
|
|
#define RF5C_MODE_CA23 0x10
|
|
#define RF5C_MODE_CA24 0x20
|
|
#define RF5C_MODE_CA25 0x40
|
|
#define RF5C_MODE_3STATE_BIT7 0x80
|
|
|
|
/* Flags for RF5C_PWR_CTL */
|
|
#define RF5C_PWR_VCC_3V 0x01
|
|
#define RF5C_PWR_IREQ_HIGH 0x02
|
|
#define RF5C_PWR_INPACK_ENA 0x04
|
|
#define RF5C_PWR_5V_DET 0x08
|
|
#define RF5C_PWR_TC_SEL 0x10 /* Terminal Count: irq 11 or 15 */
|
|
#define RF5C_PWR_DREQ_LOW 0x20
|
|
#define RF5C_PWR_DREQ_OFF 0x00 /* DREQ steering control */
|
|
#define RF5C_PWR_DREQ_INPACK 0x40
|
|
#define RF5C_PWR_DREQ_SPKR 0x80
|
|
#define RF5C_PWR_DREQ_IOIS16 0xc0
|
|
|
|
/* Values for RF5C_CHIP_ID */
|
|
#define RF5C_CHIP_RF5C296 0x32
|
|
#define RF5C_CHIP_RF5C396 0xb2
|
|
|
|
/* Flags for RF5C_MODE_CTL_3 */
|
|
#define RF5C_MCTL3_DISABLE 0x01 /* Disable PCMCIA interface */
|
|
#define RF5C_MCTL3_DMA_ENA 0x02
|
|
|
|
/* Register definitions for Ricoh PCI-to-CardBus bridges */
|
|
|
|
/* Extra bits in CB_BRIDGE_CONTROL */
|
|
#define RL5C46X_BCR_3E0_ENA 0x0800
|
|
#define RL5C46X_BCR_3E2_ENA 0x1000
|
|
|
|
/* Bridge Configuration Register */
|
|
#define RL5C4XX_CONFIG 0x80 /* 16 bit */
|
|
#define RL5C4XX_CONFIG_IO_1_MODE 0x0200
|
|
#define RL5C4XX_CONFIG_IO_0_MODE 0x0100
|
|
#define RL5C4XX_CONFIG_PREFETCH 0x0001
|
|
|
|
/* Misc Control Register */
|
|
#define RL5C4XX_MISC 0x0082 /* 16 bit */
|
|
#define RL5C4XX_MISC_HW_SUSPEND_ENA 0x0002
|
|
#define RL5C4XX_MISC_VCCEN_POL 0x0100
|
|
#define RL5C4XX_MISC_VPPEN_POL 0x0200
|
|
#define RL5C46X_MISC_SUSPEND 0x0001
|
|
#define RL5C46X_MISC_PWR_SAVE_2 0x0004
|
|
#define RL5C46X_MISC_IFACE_BUSY 0x0008
|
|
#define RL5C46X_MISC_B_LOCK 0x0010
|
|
#define RL5C46X_MISC_A_LOCK 0x0020
|
|
#define RL5C46X_MISC_PCI_LOCK 0x0040
|
|
#define RL5C47X_MISC_IFACE_BUSY 0x0004
|
|
#define RL5C47X_MISC_PCI_INT_MASK 0x0018
|
|
#define RL5C47X_MISC_PCI_INT_DIS 0x0020
|
|
#define RL5C47X_MISC_SUBSYS_WR 0x0040
|
|
#define RL5C47X_MISC_SRIRQ_ENA 0x0080
|
|
#define RL5C47X_MISC_5V_DISABLE 0x0400
|
|
#define RL5C47X_MISC_LED_POL 0x0800
|
|
|
|
/* 16-bit Interface Control Register */
|
|
#define RL5C4XX_16BIT_CTL 0x0084 /* 16 bit */
|
|
#define RL5C4XX_16CTL_IO_TIMING 0x0100
|
|
#define RL5C4XX_16CTL_MEM_TIMING 0x0200
|
|
#define RL5C46X_16CTL_LEVEL_1 0x0010
|
|
#define RL5C46X_16CTL_LEVEL_2 0x0020
|
|
|
|
/* 16-bit IO and memory timing registers */
|
|
#define RL5C4XX_16BIT_IO_0 0x0088 /* 16 bit */
|
|
#define RL5C4XX_16BIT_MEM_0 0x008a /* 16 bit */
|
|
#define RL5C4XX_SETUP_MASK 0x0007
|
|
#define RL5C4XX_SETUP_SHIFT 0
|
|
#define RL5C4XX_CMD_MASK 0x01f0
|
|
#define RL5C4XX_CMD_SHIFT 4
|
|
#define RL5C4XX_HOLD_MASK 0x1c00
|
|
#define RL5C4XX_HOLD_SHIFT 10
|
|
#define RL5C4XX_MISC_CONTROL 0x2F /* 8 bit */
|
|
#define RL5C4XX_ZV_ENABLE 0x08
|
|
|
|
/* Misc Control 3 Register */
|
|
#define RL5C4XX_MISC3 0x00A2 /* 16 bit */
|
|
#define RL5C47X_MISC3_CB_CLKRUN_DIS BIT(1)
|
|
|
|
#ifdef __YENTA_H
|
|
|
|
#define rl_misc(socket) ((socket)->private[0])
|
|
#define rl_ctl(socket) ((socket)->private[1])
|
|
#define rl_io(socket) ((socket)->private[2])
|
|
#define rl_mem(socket) ((socket)->private[3])
|
|
#define rl_config(socket) ((socket)->private[4])
|
|
|
|
static void ricoh_zoom_video(struct pcmcia_socket *sock, int onoff)
|
|
{
|
|
u8 reg;
|
|
struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
|
|
|
|
reg = config_readb(socket, RL5C4XX_MISC_CONTROL);
|
|
if (onoff)
|
|
/* Zoom zoom, we will all go together, zoom zoom, zoom zoom */
|
|
reg |= RL5C4XX_ZV_ENABLE;
|
|
else
|
|
reg &= ~RL5C4XX_ZV_ENABLE;
|
|
|
|
config_writeb(socket, RL5C4XX_MISC_CONTROL, reg);
|
|
}
|
|
|
|
static void ricoh_set_zv(struct yenta_socket *socket)
|
|
{
|
|
if(socket->dev->vendor == PCI_VENDOR_ID_RICOH)
|
|
{
|
|
switch(socket->dev->device)
|
|
{
|
|
/* There may be more .. */
|
|
case PCI_DEVICE_ID_RICOH_RL5C478:
|
|
socket->socket.zoom_video = ricoh_zoom_video;
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
|
|
static void ricoh_set_clkrun(struct yenta_socket *socket, bool quiet)
|
|
{
|
|
u16 misc3;
|
|
|
|
/*
|
|
* RL5C475II likely has this setting, too, however no datasheet
|
|
* is publicly available for this chip
|
|
*/
|
|
if (socket->dev->device != PCI_DEVICE_ID_RICOH_RL5C476 &&
|
|
socket->dev->device != PCI_DEVICE_ID_RICOH_RL5C478)
|
|
return;
|
|
|
|
if (socket->dev->revision < 0x80)
|
|
return;
|
|
|
|
misc3 = config_readw(socket, RL5C4XX_MISC3);
|
|
if (misc3 & RL5C47X_MISC3_CB_CLKRUN_DIS) {
|
|
if (!quiet)
|
|
dev_dbg(&socket->dev->dev,
|
|
"CLKRUN feature already disabled\n");
|
|
} else if (disable_clkrun) {
|
|
if (!quiet)
|
|
dev_info(&socket->dev->dev,
|
|
"Disabling CLKRUN feature\n");
|
|
misc3 |= RL5C47X_MISC3_CB_CLKRUN_DIS;
|
|
config_writew(socket, RL5C4XX_MISC3, misc3);
|
|
}
|
|
}
|
|
|
|
static void ricoh_save_state(struct yenta_socket *socket)
|
|
{
|
|
rl_misc(socket) = config_readw(socket, RL5C4XX_MISC);
|
|
rl_ctl(socket) = config_readw(socket, RL5C4XX_16BIT_CTL);
|
|
rl_io(socket) = config_readw(socket, RL5C4XX_16BIT_IO_0);
|
|
rl_mem(socket) = config_readw(socket, RL5C4XX_16BIT_MEM_0);
|
|
rl_config(socket) = config_readw(socket, RL5C4XX_CONFIG);
|
|
}
|
|
|
|
static void ricoh_restore_state(struct yenta_socket *socket)
|
|
{
|
|
config_writew(socket, RL5C4XX_MISC, rl_misc(socket));
|
|
config_writew(socket, RL5C4XX_16BIT_CTL, rl_ctl(socket));
|
|
config_writew(socket, RL5C4XX_16BIT_IO_0, rl_io(socket));
|
|
config_writew(socket, RL5C4XX_16BIT_MEM_0, rl_mem(socket));
|
|
config_writew(socket, RL5C4XX_CONFIG, rl_config(socket));
|
|
ricoh_set_clkrun(socket, true);
|
|
}
|
|
|
|
|
|
/*
|
|
* Magic Ricoh initialization code..
|
|
*/
|
|
static int ricoh_override(struct yenta_socket *socket)
|
|
{
|
|
u16 config, ctl;
|
|
|
|
config = config_readw(socket, RL5C4XX_CONFIG);
|
|
|
|
/* Set the default timings, don't trust the original values */
|
|
ctl = RL5C4XX_16CTL_IO_TIMING | RL5C4XX_16CTL_MEM_TIMING;
|
|
|
|
if(socket->dev->device < PCI_DEVICE_ID_RICOH_RL5C475) {
|
|
ctl |= RL5C46X_16CTL_LEVEL_1 | RL5C46X_16CTL_LEVEL_2;
|
|
} else {
|
|
config |= RL5C4XX_CONFIG_PREFETCH;
|
|
}
|
|
|
|
config_writew(socket, RL5C4XX_16BIT_CTL, ctl);
|
|
config_writew(socket, RL5C4XX_CONFIG, config);
|
|
|
|
ricoh_set_zv(socket);
|
|
ricoh_set_clkrun(socket, false);
|
|
|
|
return 0;
|
|
}
|
|
|
|
#endif /* CONFIG_CARDBUS */
|
|
|
|
#endif /* _LINUX_RICOH_H */
|