mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-16 08:44:21 +08:00
1da177e4c3
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
163 lines
5.3 KiB
C
163 lines
5.3 KiB
C
/*
|
|
* I/O Processor (IOP) defines and structures, mostly snagged from A/UX
|
|
* header files.
|
|
*
|
|
* The original header from which this was taken is copyrighted. I've done some
|
|
* rewriting (in fact my changes make this a bit more readable, IMHO) but some
|
|
* more should be done.
|
|
*/
|
|
|
|
/*
|
|
* This is the base address of the IOPs. Use this as the address of
|
|
* a "struct iop" (see below) to see where the actual registers fall.
|
|
*/
|
|
|
|
#define SCC_IOP_BASE_IIFX (0x50F04000)
|
|
#define ISM_IOP_BASE_IIFX (0x50F12000)
|
|
|
|
#define SCC_IOP_BASE_QUADRA (0x50F0C000)
|
|
#define ISM_IOP_BASE_QUADRA (0x50F1E000)
|
|
|
|
/* IOP status/control register bits: */
|
|
|
|
#define IOP_BYPASS 0x01 /* bypass-mode hardware access */
|
|
#define IOP_AUTOINC 0x02 /* allow autoincrement of ramhi/lo */
|
|
#define IOP_RUN 0x04 /* set to 0 to reset IOP chip */
|
|
#define IOP_IRQ 0x08 /* generate IRQ to IOP if 1 */
|
|
#define IOP_INT0 0x10 /* intr priority from IOP to host */
|
|
#define IOP_INT1 0x20 /* intr priority from IOP to host */
|
|
#define IOP_HWINT 0x40 /* IRQ from hardware; bypass mode only */
|
|
#define IOP_DMAINACTIVE 0x80 /* no DMA request active; bypass mode only */
|
|
|
|
#define NUM_IOPS 2
|
|
#define NUM_IOP_CHAN 7
|
|
#define NUM_IOP_MSGS NUM_IOP_CHAN*8
|
|
#define IOP_MSG_LEN 32
|
|
|
|
/* IOP reference numbers, used by the globally-visible iop_xxx functions */
|
|
|
|
#define IOP_NUM_SCC 0
|
|
#define IOP_NUM_ISM 1
|
|
|
|
/* IOP channel states */
|
|
|
|
#define IOP_MSG_IDLE 0 /* idle */
|
|
#define IOP_MSG_NEW 1 /* new message sent */
|
|
#define IOP_MSG_RCVD 2 /* message received; processing */
|
|
#define IOP_MSG_COMPLETE 3 /* message processing complete */
|
|
|
|
/* IOP message status codes */
|
|
|
|
#define IOP_MSGSTATUS_UNUSED 0 /* Unusued message structure */
|
|
#define IOP_MSGSTATUS_WAITING 1 /* waiting for channel */
|
|
#define IOP_MSGSTATUS_SENT 2 /* message sent, awaiting reply */
|
|
#define IOP_MSGSTATUS_COMPLETE 3 /* message complete and reply rcvd */
|
|
#define IOP_MSGSTATUS_UNSOL 6 /* message is unsolicited */
|
|
|
|
/* IOP memory addresses of the members of the mac_iop_kernel structure. */
|
|
|
|
#define IOP_ADDR_MAX_SEND_CHAN 0x0200
|
|
#define IOP_ADDR_SEND_STATE 0x0201
|
|
#define IOP_ADDR_PATCH_CTRL 0x021F
|
|
#define IOP_ADDR_SEND_MSG 0x0220
|
|
#define IOP_ADDR_MAX_RECV_CHAN 0x0300
|
|
#define IOP_ADDR_RECV_STATE 0x0301
|
|
#define IOP_ADDR_ALIVE 0x031F
|
|
#define IOP_ADDR_RECV_MSG 0x0320
|
|
|
|
#ifndef __ASSEMBLY__
|
|
|
|
/*
|
|
* IOP Control registers, staggered because in usual Apple style they were
|
|
* too lazy to decode the A0 bit. This structure is assumed to begin at
|
|
* one of the xxx_IOP_BASE addresses given above.
|
|
*/
|
|
|
|
struct mac_iop {
|
|
__u8 ram_addr_hi; /* shared RAM address hi byte */
|
|
__u8 pad0;
|
|
__u8 ram_addr_lo; /* shared RAM address lo byte */
|
|
__u8 pad1;
|
|
__u8 status_ctrl; /* status/control register */
|
|
__u8 pad2[3];
|
|
__u8 ram_data; /* RAM data byte at ramhi/lo */
|
|
|
|
__u8 pad3[23];
|
|
|
|
/* Bypass-mode hardware access registers */
|
|
|
|
union {
|
|
struct { /* SCC registers */
|
|
__u8 sccb_cmd; /* SCC B command reg */
|
|
__u8 pad4;
|
|
__u8 scca_cmd; /* SCC A command reg */
|
|
__u8 pad5;
|
|
__u8 sccb_data; /* SCC B data */
|
|
__u8 pad6;
|
|
__u8 scca_data; /* SCC A data */
|
|
} scc_regs;
|
|
|
|
struct { /* ISM registers */
|
|
__u8 wdata; /* write a data byte */
|
|
__u8 pad7;
|
|
__u8 wmark; /* write a mark byte */
|
|
__u8 pad8;
|
|
__u8 wcrc; /* write 2-byte crc to disk */
|
|
__u8 pad9;
|
|
__u8 wparams; /* write the param regs */
|
|
__u8 pad10;
|
|
__u8 wphase; /* write the phase states & dirs */
|
|
__u8 pad11;
|
|
__u8 wsetup; /* write the setup register */
|
|
__u8 pad12;
|
|
__u8 wzeroes; /* mode reg: 1's clr bits, 0's are x */
|
|
__u8 pad13;
|
|
__u8 wones; /* mode reg: 1's set bits, 0's are x */
|
|
__u8 pad14;
|
|
__u8 rdata; /* read a data byte */
|
|
__u8 pad15;
|
|
__u8 rmark; /* read a mark byte */
|
|
__u8 pad16;
|
|
__u8 rerror; /* read the error register */
|
|
__u8 pad17;
|
|
__u8 rparams; /* read the param regs */
|
|
__u8 pad18;
|
|
__u8 rphase; /* read the phase states & dirs */
|
|
__u8 pad19;
|
|
__u8 rsetup; /* read the setup register */
|
|
__u8 pad20;
|
|
__u8 rmode; /* read the mode register */
|
|
__u8 pad21;
|
|
__u8 rhandshake; /* read the handshake register */
|
|
} ism_regs;
|
|
} b;
|
|
};
|
|
|
|
/* This structure is used to track IOP messages in the Linux kernel */
|
|
|
|
struct iop_msg {
|
|
struct iop_msg *next; /* next message in queue or NULL */
|
|
uint iop_num; /* IOP number */
|
|
uint channel; /* channel number */
|
|
void *caller_priv; /* caller private data */
|
|
int status; /* status of this message */
|
|
__u8 message[IOP_MSG_LEN]; /* the message being sent/received */
|
|
__u8 reply[IOP_MSG_LEN]; /* the reply to the message */
|
|
void (*handler)(struct iop_msg *, struct pt_regs *);
|
|
/* function to call when reply recvd */
|
|
};
|
|
|
|
extern int iop_scc_present,iop_ism_present;
|
|
|
|
extern int iop_listen(uint, uint,
|
|
void (*handler)(struct iop_msg *, struct pt_regs *),
|
|
const char *);
|
|
extern int iop_send_message(uint, uint, void *, uint, __u8 *,
|
|
void (*)(struct iop_msg *, struct pt_regs *));
|
|
extern void iop_complete_message(struct iop_msg *);
|
|
extern void iop_upload_code(uint, __u8 *, uint, __u16);
|
|
extern void iop_download_code(uint, __u8 *, uint, __u16);
|
|
extern __u8 *iop_compare_code(uint, __u8 *, uint, __u16);
|
|
|
|
#endif /* __ASSEMBLY__ */
|