mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-28 21:45:01 +08:00
d2afcf09e6
The generic PHY framewrok expects different properties than the old USB PHY framework. Supply those properties. Fixes USB OTG port on GAT04 and N900 after the Generic PHY framework was merged in greg/usb-next. [1] [1] - https://lkml.org/lkml/2013/9/27/581 Signed-off-by: Roger Quadros <rogerq@ti.com> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
171 lines
3.1 KiB
Plaintext
171 lines
3.1 KiB
Plaintext
/*
|
|
* Copyright (C) 2013 Marek Belisko <marek@goldelico.com>
|
|
*
|
|
* Based on omap3-beagle-xm.dts
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
/dts-v1/;
|
|
|
|
#include "omap36xx.dtsi"
|
|
|
|
/ {
|
|
model = "OMAP3 GTA04";
|
|
compatible = "ti,omap3-gta04", "ti,omap3";
|
|
|
|
cpus {
|
|
cpu@0 {
|
|
cpu0-supply = <&vcc>;
|
|
};
|
|
};
|
|
|
|
memory {
|
|
device_type = "memory";
|
|
reg = <0x80000000 0x20000000>; /* 512 MB */
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys";
|
|
|
|
aux-button {
|
|
label = "aux";
|
|
linux,code = <169>;
|
|
gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
|
|
gpio-key,wakeup;
|
|
};
|
|
};
|
|
};
|
|
|
|
&omap3_pmx_core {
|
|
uart1_pins: pinmux_uart1_pins {
|
|
pinctrl-single,pins = <
|
|
0x152 (PIN_INPUT | MUX_MODE0) /* uart1_rx.uart1_rx */
|
|
0x14c (PIN_OUTPUT |MUX_MODE0) /* uart1_tx.uart1_tx */
|
|
>;
|
|
};
|
|
|
|
uart2_pins: pinmux_uart2_pins {
|
|
pinctrl-single,pins = <
|
|
0x14a (PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */
|
|
0x148 (PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */
|
|
>;
|
|
};
|
|
|
|
uart3_pins: pinmux_uart3_pins {
|
|
pinctrl-single,pins = <
|
|
0x16e (PIN_INPUT | MUX_MODE0) /* uart3_rx.uart3_rx */
|
|
0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx.uart3_tx */
|
|
>;
|
|
};
|
|
|
|
mmc1_pins: pinmux_mmc1_pins {
|
|
pinctrl-single,pins = <
|
|
0x114 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
|
|
0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
|
|
0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
|
|
0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
|
|
0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
|
|
0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
|
|
>;
|
|
};
|
|
};
|
|
|
|
&i2c1 {
|
|
clock-frequency = <2600000>;
|
|
|
|
twl: twl@48 {
|
|
reg = <0x48>;
|
|
interrupts = <7>; /* SYS_NIRQ cascaded to intc */
|
|
interrupt-parent = <&intc>;
|
|
};
|
|
};
|
|
|
|
#include "twl4030.dtsi"
|
|
#include "twl4030_omap3.dtsi"
|
|
|
|
&i2c2 {
|
|
clock-frequency = <400000>;
|
|
|
|
/* pressure sensor */
|
|
bmp085@77 {
|
|
compatible = "bosch,bmp085";
|
|
reg = <0x77>;
|
|
};
|
|
|
|
/* leds */
|
|
tca6507@45 {
|
|
compatible = "ti,tca6507";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0x45>;
|
|
|
|
gta04_led0: red_aux@0 {
|
|
label = "gta04:red:aux";
|
|
reg = <0x0>;
|
|
};
|
|
|
|
gta04_led1: green_aux@1 {
|
|
label = "gta04:green:aux";
|
|
reg = <0x1>;
|
|
};
|
|
|
|
gta04_led3: red_power@3 {
|
|
label = "gta04:red:power";
|
|
reg = <0x3>;
|
|
linux,default-trigger = "default-on";
|
|
};
|
|
|
|
gta04_led4: green_power@4 {
|
|
label = "gta04:green:power";
|
|
reg = <0x4>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&i2c3 {
|
|
clock-frequency = <100000>;
|
|
};
|
|
|
|
&usb_otg_hs {
|
|
interface-type = <0>;
|
|
usb-phy = <&usb2_phy>;
|
|
phys = <&usb2_phy>;
|
|
phy-names = "usb2-phy";
|
|
mode = <3>;
|
|
power = <50>;
|
|
};
|
|
|
|
&mmc1 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mmc1_pins>;
|
|
vmmc-supply = <&vmmc1>;
|
|
vmmc_aux-supply = <&vsim>;
|
|
bus-width = <4>;
|
|
};
|
|
|
|
&mmc2 {
|
|
status = "disabled";
|
|
};
|
|
|
|
&mmc3 {
|
|
status = "disabled";
|
|
};
|
|
|
|
&uart1 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart1_pins>;
|
|
};
|
|
|
|
&uart2 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart2_pins>;
|
|
};
|
|
|
|
&uart3 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart3_pins>;
|
|
};
|
|
|