mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-05 18:14:07 +08:00
867bd8868b
This change replaces the use of the `delay_usecs` field with the new `delay` field. The code/test still uses micro-seconds, but they are now configured and used via the `struct spi_delay` format of the `delay` field. Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Link: https://lore.kernel.org/r/20190926105147.7839-13-alexandru.ardelean@analog.com Signed-off-by: Mark Brown <broonie@kernel.org>
1084 lines
26 KiB
C
1084 lines
26 KiB
C
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
/*
|
|
* linux/drivers/spi/spi-loopback-test.c
|
|
*
|
|
* (c) Martin Sperl <kernel@martin.sperl.org>
|
|
*
|
|
* Loopback test driver to test several typical spi_message conditions
|
|
* that a spi_master driver may encounter
|
|
* this can also get used for regression testing
|
|
*/
|
|
|
|
#include <linux/delay.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/ktime.h>
|
|
#include <linux/list.h>
|
|
#include <linux/list_sort.h>
|
|
#include <linux/module.h>
|
|
#include <linux/of_device.h>
|
|
#include <linux/printk.h>
|
|
#include <linux/vmalloc.h>
|
|
#include <linux/spi/spi.h>
|
|
|
|
#include "spi-test.h"
|
|
|
|
/* flag to only simulate transfers */
|
|
static int simulate_only;
|
|
module_param(simulate_only, int, 0);
|
|
MODULE_PARM_DESC(simulate_only, "if not 0 do not execute the spi message");
|
|
|
|
/* dump spi messages */
|
|
static int dump_messages;
|
|
module_param(dump_messages, int, 0);
|
|
MODULE_PARM_DESC(dump_messages,
|
|
"=1 dump the basic spi_message_structure, " \
|
|
"=2 dump the spi_message_structure including data, " \
|
|
"=3 dump the spi_message structure before and after execution");
|
|
/* the device is jumpered for loopback - enabling some rx_buf tests */
|
|
static int loopback;
|
|
module_param(loopback, int, 0);
|
|
MODULE_PARM_DESC(loopback,
|
|
"if set enable loopback mode, where the rx_buf " \
|
|
"is checked to match tx_buf after the spi_message " \
|
|
"is executed");
|
|
|
|
static int loop_req;
|
|
module_param(loop_req, int, 0);
|
|
MODULE_PARM_DESC(loop_req,
|
|
"if set controller will be asked to enable test loop mode. " \
|
|
"If controller supported it, MISO and MOSI will be connected");
|
|
|
|
static int no_cs;
|
|
module_param(no_cs, int, 0);
|
|
MODULE_PARM_DESC(no_cs,
|
|
"if set Chip Select (CS) will not be used");
|
|
|
|
/* run only a specific test */
|
|
static int run_only_test = -1;
|
|
module_param(run_only_test, int, 0);
|
|
MODULE_PARM_DESC(run_only_test,
|
|
"only run the test with this number (0-based !)");
|
|
|
|
/* use vmalloc'ed buffers */
|
|
static int use_vmalloc;
|
|
module_param(use_vmalloc, int, 0644);
|
|
MODULE_PARM_DESC(use_vmalloc,
|
|
"use vmalloc'ed buffers instead of kmalloc'ed");
|
|
|
|
/* check rx ranges */
|
|
static int check_ranges = 1;
|
|
module_param(check_ranges, int, 0644);
|
|
MODULE_PARM_DESC(check_ranges,
|
|
"checks rx_buffer pattern are valid");
|
|
|
|
/* the actual tests to execute */
|
|
static struct spi_test spi_tests[] = {
|
|
{
|
|
.description = "tx/rx-transfer - start of page",
|
|
.fill_option = FILL_COUNT_8,
|
|
.iterate_len = { ITERATE_MAX_LEN },
|
|
.iterate_tx_align = ITERATE_ALIGN,
|
|
.iterate_rx_align = ITERATE_ALIGN,
|
|
.transfer_count = 1,
|
|
.transfers = {
|
|
{
|
|
.tx_buf = TX(0),
|
|
.rx_buf = RX(0),
|
|
},
|
|
},
|
|
},
|
|
{
|
|
.description = "tx/rx-transfer - crossing PAGE_SIZE",
|
|
.fill_option = FILL_COUNT_8,
|
|
.iterate_len = { ITERATE_MAX_LEN },
|
|
.iterate_tx_align = ITERATE_ALIGN,
|
|
.iterate_rx_align = ITERATE_ALIGN,
|
|
.transfer_count = 1,
|
|
.transfers = {
|
|
{
|
|
.tx_buf = TX(PAGE_SIZE - 4),
|
|
.rx_buf = RX(PAGE_SIZE - 4),
|
|
},
|
|
},
|
|
},
|
|
{
|
|
.description = "tx-transfer - only",
|
|
.fill_option = FILL_COUNT_8,
|
|
.iterate_len = { ITERATE_MAX_LEN },
|
|
.iterate_tx_align = ITERATE_ALIGN,
|
|
.transfer_count = 1,
|
|
.transfers = {
|
|
{
|
|
.tx_buf = TX(0),
|
|
},
|
|
},
|
|
},
|
|
{
|
|
.description = "rx-transfer - only",
|
|
.fill_option = FILL_COUNT_8,
|
|
.iterate_len = { ITERATE_MAX_LEN },
|
|
.iterate_rx_align = ITERATE_ALIGN,
|
|
.transfer_count = 1,
|
|
.transfers = {
|
|
{
|
|
.rx_buf = RX(0),
|
|
},
|
|
},
|
|
},
|
|
{
|
|
.description = "two tx-transfers - alter both",
|
|
.fill_option = FILL_COUNT_8,
|
|
.iterate_len = { ITERATE_LEN },
|
|
.iterate_tx_align = ITERATE_ALIGN,
|
|
.iterate_transfer_mask = BIT(0) | BIT(1),
|
|
.transfer_count = 2,
|
|
.transfers = {
|
|
{
|
|
.tx_buf = TX(0),
|
|
},
|
|
{
|
|
/* this is why we cant use ITERATE_MAX_LEN */
|
|
.tx_buf = TX(SPI_TEST_MAX_SIZE_HALF),
|
|
},
|
|
},
|
|
},
|
|
{
|
|
.description = "two tx-transfers - alter first",
|
|
.fill_option = FILL_COUNT_8,
|
|
.iterate_len = { ITERATE_MAX_LEN },
|
|
.iterate_tx_align = ITERATE_ALIGN,
|
|
.iterate_transfer_mask = BIT(0),
|
|
.transfer_count = 2,
|
|
.transfers = {
|
|
{
|
|
.tx_buf = TX(64),
|
|
},
|
|
{
|
|
.len = 1,
|
|
.tx_buf = TX(0),
|
|
},
|
|
},
|
|
},
|
|
{
|
|
.description = "two tx-transfers - alter second",
|
|
.fill_option = FILL_COUNT_8,
|
|
.iterate_len = { ITERATE_MAX_LEN },
|
|
.iterate_tx_align = ITERATE_ALIGN,
|
|
.iterate_transfer_mask = BIT(1),
|
|
.transfer_count = 2,
|
|
.transfers = {
|
|
{
|
|
.len = 16,
|
|
.tx_buf = TX(0),
|
|
},
|
|
{
|
|
.tx_buf = TX(64),
|
|
},
|
|
},
|
|
},
|
|
{
|
|
.description = "two transfers tx then rx - alter both",
|
|
.fill_option = FILL_COUNT_8,
|
|
.iterate_len = { ITERATE_MAX_LEN },
|
|
.iterate_tx_align = ITERATE_ALIGN,
|
|
.iterate_transfer_mask = BIT(0) | BIT(1),
|
|
.transfer_count = 2,
|
|
.transfers = {
|
|
{
|
|
.tx_buf = TX(0),
|
|
},
|
|
{
|
|
.rx_buf = RX(0),
|
|
},
|
|
},
|
|
},
|
|
{
|
|
.description = "two transfers tx then rx - alter tx",
|
|
.fill_option = FILL_COUNT_8,
|
|
.iterate_len = { ITERATE_MAX_LEN },
|
|
.iterate_tx_align = ITERATE_ALIGN,
|
|
.iterate_transfer_mask = BIT(0),
|
|
.transfer_count = 2,
|
|
.transfers = {
|
|
{
|
|
.tx_buf = TX(0),
|
|
},
|
|
{
|
|
.len = 1,
|
|
.rx_buf = RX(0),
|
|
},
|
|
},
|
|
},
|
|
{
|
|
.description = "two transfers tx then rx - alter rx",
|
|
.fill_option = FILL_COUNT_8,
|
|
.iterate_len = { ITERATE_MAX_LEN },
|
|
.iterate_tx_align = ITERATE_ALIGN,
|
|
.iterate_transfer_mask = BIT(1),
|
|
.transfer_count = 2,
|
|
.transfers = {
|
|
{
|
|
.len = 1,
|
|
.tx_buf = TX(0),
|
|
},
|
|
{
|
|
.rx_buf = RX(0),
|
|
},
|
|
},
|
|
},
|
|
{
|
|
.description = "two tx+rx transfers - alter both",
|
|
.fill_option = FILL_COUNT_8,
|
|
.iterate_len = { ITERATE_LEN },
|
|
.iterate_tx_align = ITERATE_ALIGN,
|
|
.iterate_transfer_mask = BIT(0) | BIT(1),
|
|
.transfer_count = 2,
|
|
.transfers = {
|
|
{
|
|
.tx_buf = TX(0),
|
|
.rx_buf = RX(0),
|
|
},
|
|
{
|
|
/* making sure we align without overwrite
|
|
* the reason we can not use ITERATE_MAX_LEN
|
|
*/
|
|
.tx_buf = TX(SPI_TEST_MAX_SIZE_HALF),
|
|
.rx_buf = RX(SPI_TEST_MAX_SIZE_HALF),
|
|
},
|
|
},
|
|
},
|
|
{
|
|
.description = "two tx+rx transfers - alter first",
|
|
.fill_option = FILL_COUNT_8,
|
|
.iterate_len = { ITERATE_MAX_LEN },
|
|
.iterate_tx_align = ITERATE_ALIGN,
|
|
.iterate_transfer_mask = BIT(0),
|
|
.transfer_count = 2,
|
|
.transfers = {
|
|
{
|
|
/* making sure we align without overwrite */
|
|
.tx_buf = TX(1024),
|
|
.rx_buf = RX(1024),
|
|
},
|
|
{
|
|
.len = 1,
|
|
/* making sure we align without overwrite */
|
|
.tx_buf = TX(0),
|
|
.rx_buf = RX(0),
|
|
},
|
|
},
|
|
},
|
|
{
|
|
.description = "two tx+rx transfers - alter second",
|
|
.fill_option = FILL_COUNT_8,
|
|
.iterate_len = { ITERATE_MAX_LEN },
|
|
.iterate_tx_align = ITERATE_ALIGN,
|
|
.iterate_transfer_mask = BIT(1),
|
|
.transfer_count = 2,
|
|
.transfers = {
|
|
{
|
|
.len = 1,
|
|
.tx_buf = TX(0),
|
|
.rx_buf = RX(0),
|
|
},
|
|
{
|
|
/* making sure we align without overwrite */
|
|
.tx_buf = TX(1024),
|
|
.rx_buf = RX(1024),
|
|
},
|
|
},
|
|
},
|
|
{
|
|
.description = "two tx+rx transfers - delay after transfer",
|
|
.fill_option = FILL_COUNT_8,
|
|
.iterate_len = { ITERATE_MAX_LEN },
|
|
.iterate_transfer_mask = BIT(0) | BIT(1),
|
|
.transfer_count = 2,
|
|
.transfers = {
|
|
{
|
|
.tx_buf = TX(0),
|
|
.rx_buf = RX(0),
|
|
.delay = {
|
|
.value = 1000,
|
|
.unit = SPI_DELAY_UNIT_USECS,
|
|
},
|
|
},
|
|
{
|
|
.tx_buf = TX(0),
|
|
.rx_buf = RX(0),
|
|
.delay = {
|
|
.value = 1000,
|
|
.unit = SPI_DELAY_UNIT_USECS,
|
|
},
|
|
},
|
|
},
|
|
},
|
|
|
|
{ /* end of tests sequence */ }
|
|
};
|
|
|
|
static int spi_loopback_test_probe(struct spi_device *spi)
|
|
{
|
|
int ret;
|
|
|
|
if (loop_req || no_cs) {
|
|
spi->mode |= loop_req ? SPI_LOOP : 0;
|
|
spi->mode |= no_cs ? SPI_NO_CS : 0;
|
|
ret = spi_setup(spi);
|
|
if (ret) {
|
|
dev_err(&spi->dev, "SPI setup with SPI_LOOP or SPI_NO_CS failed (%d)\n",
|
|
ret);
|
|
return ret;
|
|
}
|
|
}
|
|
|
|
dev_info(&spi->dev, "Executing spi-loopback-tests\n");
|
|
|
|
ret = spi_test_run_tests(spi, spi_tests);
|
|
|
|
dev_info(&spi->dev, "Finished spi-loopback-tests with return: %i\n",
|
|
ret);
|
|
|
|
return ret;
|
|
}
|
|
|
|
/* non const match table to permit to change via a module parameter */
|
|
static struct of_device_id spi_loopback_test_of_match[] = {
|
|
{ .compatible = "linux,spi-loopback-test", },
|
|
{ }
|
|
};
|
|
|
|
/* allow to override the compatible string via a module_parameter */
|
|
module_param_string(compatible, spi_loopback_test_of_match[0].compatible,
|
|
sizeof(spi_loopback_test_of_match[0].compatible),
|
|
0000);
|
|
|
|
MODULE_DEVICE_TABLE(of, spi_loopback_test_of_match);
|
|
|
|
static struct spi_driver spi_loopback_test_driver = {
|
|
.driver = {
|
|
.name = "spi-loopback-test",
|
|
.owner = THIS_MODULE,
|
|
.of_match_table = spi_loopback_test_of_match,
|
|
},
|
|
.probe = spi_loopback_test_probe,
|
|
};
|
|
|
|
module_spi_driver(spi_loopback_test_driver);
|
|
|
|
MODULE_AUTHOR("Martin Sperl <kernel@martin.sperl.org>");
|
|
MODULE_DESCRIPTION("test spi_driver to check core functionality");
|
|
MODULE_LICENSE("GPL");
|
|
|
|
/*-------------------------------------------------------------------------*/
|
|
|
|
/* spi_test implementation */
|
|
|
|
#define RANGE_CHECK(ptr, plen, start, slen) \
|
|
((ptr >= start) && (ptr + plen <= start + slen))
|
|
|
|
/* we allocate one page more, to allow for offsets */
|
|
#define SPI_TEST_MAX_SIZE_PLUS (SPI_TEST_MAX_SIZE + PAGE_SIZE)
|
|
|
|
static void spi_test_print_hex_dump(char *pre, const void *ptr, size_t len)
|
|
{
|
|
/* limit the hex_dump */
|
|
if (len < 1024) {
|
|
print_hex_dump(KERN_INFO, pre,
|
|
DUMP_PREFIX_OFFSET, 16, 1,
|
|
ptr, len, 0);
|
|
return;
|
|
}
|
|
/* print head */
|
|
print_hex_dump(KERN_INFO, pre,
|
|
DUMP_PREFIX_OFFSET, 16, 1,
|
|
ptr, 512, 0);
|
|
/* print tail */
|
|
pr_info("%s truncated - continuing at offset %04zx\n",
|
|
pre, len - 512);
|
|
print_hex_dump(KERN_INFO, pre,
|
|
DUMP_PREFIX_OFFSET, 16, 1,
|
|
ptr + (len - 512), 512, 0);
|
|
}
|
|
|
|
static void spi_test_dump_message(struct spi_device *spi,
|
|
struct spi_message *msg,
|
|
bool dump_data)
|
|
{
|
|
struct spi_transfer *xfer;
|
|
int i;
|
|
u8 b;
|
|
|
|
dev_info(&spi->dev, " spi_msg@%pK\n", msg);
|
|
if (msg->status)
|
|
dev_info(&spi->dev, " status: %i\n",
|
|
msg->status);
|
|
dev_info(&spi->dev, " frame_length: %i\n",
|
|
msg->frame_length);
|
|
dev_info(&spi->dev, " actual_length: %i\n",
|
|
msg->actual_length);
|
|
|
|
list_for_each_entry(xfer, &msg->transfers, transfer_list) {
|
|
dev_info(&spi->dev, " spi_transfer@%pK\n", xfer);
|
|
dev_info(&spi->dev, " len: %i\n", xfer->len);
|
|
dev_info(&spi->dev, " tx_buf: %pK\n", xfer->tx_buf);
|
|
if (dump_data && xfer->tx_buf)
|
|
spi_test_print_hex_dump(" TX: ",
|
|
xfer->tx_buf,
|
|
xfer->len);
|
|
|
|
dev_info(&spi->dev, " rx_buf: %pK\n", xfer->rx_buf);
|
|
if (dump_data && xfer->rx_buf)
|
|
spi_test_print_hex_dump(" RX: ",
|
|
xfer->rx_buf,
|
|
xfer->len);
|
|
/* check for unwritten test pattern on rx_buf */
|
|
if (xfer->rx_buf) {
|
|
for (i = 0 ; i < xfer->len ; i++) {
|
|
b = ((u8 *)xfer->rx_buf)[xfer->len - 1 - i];
|
|
if (b != SPI_TEST_PATTERN_UNWRITTEN)
|
|
break;
|
|
}
|
|
if (i)
|
|
dev_info(&spi->dev,
|
|
" rx_buf filled with %02x starts at offset: %i\n",
|
|
SPI_TEST_PATTERN_UNWRITTEN,
|
|
xfer->len - i);
|
|
}
|
|
}
|
|
}
|
|
|
|
struct rx_ranges {
|
|
struct list_head list;
|
|
u8 *start;
|
|
u8 *end;
|
|
};
|
|
|
|
static int rx_ranges_cmp(void *priv, struct list_head *a, struct list_head *b)
|
|
{
|
|
struct rx_ranges *rx_a = list_entry(a, struct rx_ranges, list);
|
|
struct rx_ranges *rx_b = list_entry(b, struct rx_ranges, list);
|
|
|
|
if (rx_a->start > rx_b->start)
|
|
return 1;
|
|
if (rx_a->start < rx_b->start)
|
|
return -1;
|
|
return 0;
|
|
}
|
|
|
|
static int spi_check_rx_ranges(struct spi_device *spi,
|
|
struct spi_message *msg,
|
|
void *rx)
|
|
{
|
|
struct spi_transfer *xfer;
|
|
struct rx_ranges ranges[SPI_TEST_MAX_TRANSFERS], *r;
|
|
int i = 0;
|
|
LIST_HEAD(ranges_list);
|
|
u8 *addr;
|
|
int ret = 0;
|
|
|
|
/* loop over all transfers to fill in the rx_ranges */
|
|
list_for_each_entry(xfer, &msg->transfers, transfer_list) {
|
|
/* if there is no rx, then no check is needed */
|
|
if (!xfer->rx_buf)
|
|
continue;
|
|
/* fill in the rx_range */
|
|
if (RANGE_CHECK(xfer->rx_buf, xfer->len,
|
|
rx, SPI_TEST_MAX_SIZE_PLUS)) {
|
|
ranges[i].start = xfer->rx_buf;
|
|
ranges[i].end = xfer->rx_buf + xfer->len;
|
|
list_add(&ranges[i].list, &ranges_list);
|
|
i++;
|
|
}
|
|
}
|
|
|
|
/* if no ranges, then we can return and avoid the checks...*/
|
|
if (!i)
|
|
return 0;
|
|
|
|
/* sort the list */
|
|
list_sort(NULL, &ranges_list, rx_ranges_cmp);
|
|
|
|
/* and iterate over all the rx addresses */
|
|
for (addr = rx; addr < (u8 *)rx + SPI_TEST_MAX_SIZE_PLUS; addr++) {
|
|
/* if we are the DO not write pattern,
|
|
* then continue with the loop...
|
|
*/
|
|
if (*addr == SPI_TEST_PATTERN_DO_NOT_WRITE)
|
|
continue;
|
|
|
|
/* check if we are inside a range */
|
|
list_for_each_entry(r, &ranges_list, list) {
|
|
/* if so then set to end... */
|
|
if ((addr >= r->start) && (addr < r->end))
|
|
addr = r->end;
|
|
}
|
|
/* second test after a (hopefull) translation */
|
|
if (*addr == SPI_TEST_PATTERN_DO_NOT_WRITE)
|
|
continue;
|
|
|
|
/* if still not found then something has modified too much */
|
|
/* we could list the "closest" transfer here... */
|
|
dev_err(&spi->dev,
|
|
"loopback strangeness - rx changed outside of allowed range at: %pK\n",
|
|
addr);
|
|
/* do not return, only set ret,
|
|
* so that we list all addresses
|
|
*/
|
|
ret = -ERANGE;
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int spi_test_check_elapsed_time(struct spi_device *spi,
|
|
struct spi_test *test)
|
|
{
|
|
int i;
|
|
unsigned long long estimated_time = 0;
|
|
unsigned long long delay_usecs = 0;
|
|
|
|
for (i = 0; i < test->transfer_count; i++) {
|
|
struct spi_transfer *xfer = test->transfers + i;
|
|
unsigned long long nbits = (unsigned long long)BITS_PER_BYTE *
|
|
xfer->len;
|
|
|
|
delay_usecs += xfer->delay.value;
|
|
if (!xfer->speed_hz)
|
|
continue;
|
|
estimated_time += div_u64(nbits * NSEC_PER_SEC, xfer->speed_hz);
|
|
}
|
|
|
|
estimated_time += delay_usecs * NSEC_PER_USEC;
|
|
if (test->elapsed_time < estimated_time) {
|
|
dev_err(&spi->dev,
|
|
"elapsed time %lld ns is shorter than minimum estimated time %lld ns\n",
|
|
test->elapsed_time, estimated_time);
|
|
|
|
return -EINVAL;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int spi_test_check_loopback_result(struct spi_device *spi,
|
|
struct spi_message *msg,
|
|
void *tx, void *rx)
|
|
{
|
|
struct spi_transfer *xfer;
|
|
u8 rxb, txb;
|
|
size_t i;
|
|
int ret;
|
|
|
|
/* checks rx_buffer pattern are valid with loopback or without */
|
|
if (check_ranges) {
|
|
ret = spi_check_rx_ranges(spi, msg, rx);
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
|
|
/* if we run without loopback, then return now */
|
|
if (!loopback)
|
|
return 0;
|
|
|
|
/* if applicable to transfer check that rx_buf is equal to tx_buf */
|
|
list_for_each_entry(xfer, &msg->transfers, transfer_list) {
|
|
/* if there is no rx, then no check is needed */
|
|
if (!xfer->len || !xfer->rx_buf)
|
|
continue;
|
|
/* so depending on tx_buf we need to handle things */
|
|
if (xfer->tx_buf) {
|
|
for (i = 0; i < xfer->len; i++) {
|
|
txb = ((u8 *)xfer->tx_buf)[i];
|
|
rxb = ((u8 *)xfer->rx_buf)[i];
|
|
if (txb != rxb)
|
|
goto mismatch_error;
|
|
}
|
|
} else {
|
|
/* first byte received */
|
|
txb = ((u8 *)xfer->rx_buf)[0];
|
|
/* first byte may be 0 or xff */
|
|
if (!((txb == 0) || (txb == 0xff))) {
|
|
dev_err(&spi->dev,
|
|
"loopback strangeness - we expect 0x00 or 0xff, but not 0x%02x\n",
|
|
txb);
|
|
return -EINVAL;
|
|
}
|
|
/* check that all bytes are identical */
|
|
for (i = 1; i < xfer->len; i++) {
|
|
rxb = ((u8 *)xfer->rx_buf)[i];
|
|
if (rxb != txb)
|
|
goto mismatch_error;
|
|
}
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
|
|
mismatch_error:
|
|
dev_err(&spi->dev,
|
|
"loopback strangeness - transfer mismatch on byte %04zx - expected 0x%02x, but got 0x%02x\n",
|
|
i, txb, rxb);
|
|
|
|
return -EINVAL;
|
|
}
|
|
|
|
static int spi_test_translate(struct spi_device *spi,
|
|
void **ptr, size_t len,
|
|
void *tx, void *rx)
|
|
{
|
|
size_t off;
|
|
|
|
/* return on null */
|
|
if (!*ptr)
|
|
return 0;
|
|
|
|
/* in the MAX_SIZE_HALF case modify the pointer */
|
|
if (((size_t)*ptr) & SPI_TEST_MAX_SIZE_HALF)
|
|
/* move the pointer to the correct range */
|
|
*ptr += (SPI_TEST_MAX_SIZE_PLUS / 2) -
|
|
SPI_TEST_MAX_SIZE_HALF;
|
|
|
|
/* RX range
|
|
* - we check against MAX_SIZE_PLUS to allow for automated alignment
|
|
*/
|
|
if (RANGE_CHECK(*ptr, len, RX(0), SPI_TEST_MAX_SIZE_PLUS)) {
|
|
off = *ptr - RX(0);
|
|
*ptr = rx + off;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* TX range */
|
|
if (RANGE_CHECK(*ptr, len, TX(0), SPI_TEST_MAX_SIZE_PLUS)) {
|
|
off = *ptr - TX(0);
|
|
*ptr = tx + off;
|
|
|
|
return 0;
|
|
}
|
|
|
|
dev_err(&spi->dev,
|
|
"PointerRange [%pK:%pK[ not in range [%pK:%pK[ or [%pK:%pK[\n",
|
|
*ptr, *ptr + len,
|
|
RX(0), RX(SPI_TEST_MAX_SIZE),
|
|
TX(0), TX(SPI_TEST_MAX_SIZE));
|
|
|
|
return -EINVAL;
|
|
}
|
|
|
|
static int spi_test_fill_pattern(struct spi_device *spi,
|
|
struct spi_test *test)
|
|
{
|
|
struct spi_transfer *xfers = test->transfers;
|
|
u8 *tx_buf;
|
|
size_t count = 0;
|
|
int i, j;
|
|
|
|
#ifdef __BIG_ENDIAN
|
|
#define GET_VALUE_BYTE(value, index, bytes) \
|
|
(value >> (8 * (bytes - 1 - count % bytes)))
|
|
#else
|
|
#define GET_VALUE_BYTE(value, index, bytes) \
|
|
(value >> (8 * (count % bytes)))
|
|
#endif
|
|
|
|
/* fill all transfers with the pattern requested */
|
|
for (i = 0; i < test->transfer_count; i++) {
|
|
/* fill rx_buf with SPI_TEST_PATTERN_UNWRITTEN */
|
|
if (xfers[i].rx_buf)
|
|
memset(xfers[i].rx_buf, SPI_TEST_PATTERN_UNWRITTEN,
|
|
xfers[i].len);
|
|
/* if tx_buf is NULL then skip */
|
|
tx_buf = (u8 *)xfers[i].tx_buf;
|
|
if (!tx_buf)
|
|
continue;
|
|
/* modify all the transfers */
|
|
for (j = 0; j < xfers[i].len; j++, tx_buf++, count++) {
|
|
/* fill tx */
|
|
switch (test->fill_option) {
|
|
case FILL_MEMSET_8:
|
|
*tx_buf = test->fill_pattern;
|
|
break;
|
|
case FILL_MEMSET_16:
|
|
*tx_buf = GET_VALUE_BYTE(test->fill_pattern,
|
|
count, 2);
|
|
break;
|
|
case FILL_MEMSET_24:
|
|
*tx_buf = GET_VALUE_BYTE(test->fill_pattern,
|
|
count, 3);
|
|
break;
|
|
case FILL_MEMSET_32:
|
|
*tx_buf = GET_VALUE_BYTE(test->fill_pattern,
|
|
count, 4);
|
|
break;
|
|
case FILL_COUNT_8:
|
|
*tx_buf = count;
|
|
break;
|
|
case FILL_COUNT_16:
|
|
*tx_buf = GET_VALUE_BYTE(count, count, 2);
|
|
break;
|
|
case FILL_COUNT_24:
|
|
*tx_buf = GET_VALUE_BYTE(count, count, 3);
|
|
break;
|
|
case FILL_COUNT_32:
|
|
*tx_buf = GET_VALUE_BYTE(count, count, 4);
|
|
break;
|
|
case FILL_TRANSFER_BYTE_8:
|
|
*tx_buf = j;
|
|
break;
|
|
case FILL_TRANSFER_BYTE_16:
|
|
*tx_buf = GET_VALUE_BYTE(j, j, 2);
|
|
break;
|
|
case FILL_TRANSFER_BYTE_24:
|
|
*tx_buf = GET_VALUE_BYTE(j, j, 3);
|
|
break;
|
|
case FILL_TRANSFER_BYTE_32:
|
|
*tx_buf = GET_VALUE_BYTE(j, j, 4);
|
|
break;
|
|
case FILL_TRANSFER_NUM:
|
|
*tx_buf = i;
|
|
break;
|
|
default:
|
|
dev_err(&spi->dev,
|
|
"unsupported fill_option: %i\n",
|
|
test->fill_option);
|
|
return -EINVAL;
|
|
}
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int _spi_test_run_iter(struct spi_device *spi,
|
|
struct spi_test *test,
|
|
void *tx, void *rx)
|
|
{
|
|
struct spi_message *msg = &test->msg;
|
|
struct spi_transfer *x;
|
|
int i, ret;
|
|
|
|
/* initialize message - zero-filled via static initialization */
|
|
spi_message_init_no_memset(msg);
|
|
|
|
/* fill rx with the DO_NOT_WRITE pattern */
|
|
memset(rx, SPI_TEST_PATTERN_DO_NOT_WRITE, SPI_TEST_MAX_SIZE_PLUS);
|
|
|
|
/* add the individual transfers */
|
|
for (i = 0; i < test->transfer_count; i++) {
|
|
x = &test->transfers[i];
|
|
|
|
/* patch the values of tx_buf */
|
|
ret = spi_test_translate(spi, (void **)&x->tx_buf, x->len,
|
|
(void *)tx, rx);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* patch the values of rx_buf */
|
|
ret = spi_test_translate(spi, &x->rx_buf, x->len,
|
|
(void *)tx, rx);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* and add it to the list */
|
|
spi_message_add_tail(x, msg);
|
|
}
|
|
|
|
/* fill in the transfer buffers with pattern */
|
|
ret = spi_test_fill_pattern(spi, test);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* and execute */
|
|
if (test->execute_msg)
|
|
ret = test->execute_msg(spi, test, tx, rx);
|
|
else
|
|
ret = spi_test_execute_msg(spi, test, tx, rx);
|
|
|
|
/* handle result */
|
|
if (ret == test->expected_return)
|
|
return 0;
|
|
|
|
dev_err(&spi->dev,
|
|
"test failed - test returned %i, but we expect %i\n",
|
|
ret, test->expected_return);
|
|
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* if it is 0, as we expected something else,
|
|
* then return something special
|
|
*/
|
|
return -EFAULT;
|
|
}
|
|
|
|
static int spi_test_run_iter(struct spi_device *spi,
|
|
const struct spi_test *testtemplate,
|
|
void *tx, void *rx,
|
|
size_t len,
|
|
size_t tx_off,
|
|
size_t rx_off
|
|
)
|
|
{
|
|
struct spi_test test;
|
|
int i, tx_count, rx_count;
|
|
|
|
/* copy the test template to test */
|
|
memcpy(&test, testtemplate, sizeof(test));
|
|
|
|
/* if iterate_transfer_mask is not set,
|
|
* then set it to first transfer only
|
|
*/
|
|
if (!(test.iterate_transfer_mask & (BIT(test.transfer_count) - 1)))
|
|
test.iterate_transfer_mask = 1;
|
|
|
|
/* count number of transfers with tx/rx_buf != NULL */
|
|
rx_count = tx_count = 0;
|
|
for (i = 0; i < test.transfer_count; i++) {
|
|
if (test.transfers[i].tx_buf)
|
|
tx_count++;
|
|
if (test.transfers[i].rx_buf)
|
|
rx_count++;
|
|
}
|
|
|
|
/* in some iteration cases warn and exit early,
|
|
* as there is nothing to do, that has not been tested already...
|
|
*/
|
|
if (tx_off && (!tx_count)) {
|
|
dev_warn_once(&spi->dev,
|
|
"%s: iterate_tx_off configured with tx_buf==NULL - ignoring\n",
|
|
test.description);
|
|
return 0;
|
|
}
|
|
if (rx_off && (!rx_count)) {
|
|
dev_warn_once(&spi->dev,
|
|
"%s: iterate_rx_off configured with rx_buf==NULL - ignoring\n",
|
|
test.description);
|
|
return 0;
|
|
}
|
|
|
|
/* write out info */
|
|
if (!(len || tx_off || rx_off)) {
|
|
dev_info(&spi->dev, "Running test %s\n", test.description);
|
|
} else {
|
|
dev_info(&spi->dev,
|
|
" with iteration values: len = %zu, tx_off = %zu, rx_off = %zu\n",
|
|
len, tx_off, rx_off);
|
|
}
|
|
|
|
/* update in the values from iteration values */
|
|
for (i = 0; i < test.transfer_count; i++) {
|
|
/* only when bit in transfer mask is set */
|
|
if (!(test.iterate_transfer_mask & BIT(i)))
|
|
continue;
|
|
test.transfers[i].len = len;
|
|
if (test.transfers[i].tx_buf)
|
|
test.transfers[i].tx_buf += tx_off;
|
|
if (test.transfers[i].tx_buf)
|
|
test.transfers[i].rx_buf += rx_off;
|
|
}
|
|
|
|
/* and execute */
|
|
return _spi_test_run_iter(spi, &test, tx, rx);
|
|
}
|
|
|
|
/**
|
|
* spi_test_execute_msg - default implementation to run a test
|
|
*
|
|
* spi: @spi_device on which to run the @spi_message
|
|
* test: the test to execute, which already contains @msg
|
|
* tx: the tx buffer allocated for the test sequence
|
|
* rx: the rx buffer allocated for the test sequence
|
|
*
|
|
* Returns: error code of spi_sync as well as basic error checking
|
|
*/
|
|
int spi_test_execute_msg(struct spi_device *spi, struct spi_test *test,
|
|
void *tx, void *rx)
|
|
{
|
|
struct spi_message *msg = &test->msg;
|
|
int ret = 0;
|
|
int i;
|
|
|
|
/* only if we do not simulate */
|
|
if (!simulate_only) {
|
|
ktime_t start;
|
|
|
|
/* dump the complete message before and after the transfer */
|
|
if (dump_messages == 3)
|
|
spi_test_dump_message(spi, msg, true);
|
|
|
|
start = ktime_get();
|
|
/* run spi message */
|
|
ret = spi_sync(spi, msg);
|
|
test->elapsed_time = ktime_to_ns(ktime_sub(ktime_get(), start));
|
|
if (ret == -ETIMEDOUT) {
|
|
dev_info(&spi->dev,
|
|
"spi-message timed out - rerunning...\n");
|
|
/* rerun after a few explicit schedules */
|
|
for (i = 0; i < 16; i++)
|
|
schedule();
|
|
ret = spi_sync(spi, msg);
|
|
}
|
|
if (ret) {
|
|
dev_err(&spi->dev,
|
|
"Failed to execute spi_message: %i\n",
|
|
ret);
|
|
goto exit;
|
|
}
|
|
|
|
/* do some extra error checks */
|
|
if (msg->frame_length != msg->actual_length) {
|
|
dev_err(&spi->dev,
|
|
"actual length differs from expected\n");
|
|
ret = -EIO;
|
|
goto exit;
|
|
}
|
|
|
|
/* run rx-buffer tests */
|
|
ret = spi_test_check_loopback_result(spi, msg, tx, rx);
|
|
if (ret)
|
|
goto exit;
|
|
|
|
ret = spi_test_check_elapsed_time(spi, test);
|
|
}
|
|
|
|
/* if requested or on error dump message (including data) */
|
|
exit:
|
|
if (dump_messages || ret)
|
|
spi_test_dump_message(spi, msg,
|
|
(dump_messages >= 2) || (ret));
|
|
|
|
return ret;
|
|
}
|
|
EXPORT_SYMBOL_GPL(spi_test_execute_msg);
|
|
|
|
/**
|
|
* spi_test_run_test - run an individual spi_test
|
|
* including all the relevant iterations on:
|
|
* length and buffer alignment
|
|
*
|
|
* spi: the spi_device to send the messages to
|
|
* test: the test which we need to execute
|
|
* tx: the tx buffer allocated for the test sequence
|
|
* rx: the rx buffer allocated for the test sequence
|
|
*
|
|
* Returns: status code of spi_sync or other failures
|
|
*/
|
|
|
|
int spi_test_run_test(struct spi_device *spi, const struct spi_test *test,
|
|
void *tx, void *rx)
|
|
{
|
|
int idx_len;
|
|
size_t len;
|
|
size_t tx_align, rx_align;
|
|
int ret;
|
|
|
|
/* test for transfer limits */
|
|
if (test->transfer_count >= SPI_TEST_MAX_TRANSFERS) {
|
|
dev_err(&spi->dev,
|
|
"%s: Exceeded max number of transfers with %i\n",
|
|
test->description, test->transfer_count);
|
|
return -E2BIG;
|
|
}
|
|
|
|
/* setting up some values in spi_message
|
|
* based on some settings in spi_master
|
|
* some of this can also get done in the run() method
|
|
*/
|
|
|
|
/* iterate over all the iterable values using macros
|
|
* (to make it a bit more readable...
|
|
*/
|
|
#define FOR_EACH_ALIGNMENT(var) \
|
|
for (var = 0; \
|
|
var < (test->iterate_##var ? \
|
|
(spi->master->dma_alignment ? \
|
|
spi->master->dma_alignment : \
|
|
test->iterate_##var) : \
|
|
1); \
|
|
var++)
|
|
|
|
for (idx_len = 0; idx_len < SPI_TEST_MAX_ITERATE &&
|
|
(len = test->iterate_len[idx_len]) != -1; idx_len++) {
|
|
FOR_EACH_ALIGNMENT(tx_align) {
|
|
FOR_EACH_ALIGNMENT(rx_align) {
|
|
/* and run the iteration */
|
|
ret = spi_test_run_iter(spi, test,
|
|
tx, rx,
|
|
len,
|
|
tx_align,
|
|
rx_align);
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
EXPORT_SYMBOL_GPL(spi_test_run_test);
|
|
|
|
/**
|
|
* spi_test_run_tests - run an array of spi_messages tests
|
|
* @spi: the spi device on which to run the tests
|
|
* @tests: NULL-terminated array of @spi_test
|
|
*
|
|
* Returns: status errors as per @spi_test_run_test()
|
|
*/
|
|
|
|
int spi_test_run_tests(struct spi_device *spi,
|
|
struct spi_test *tests)
|
|
{
|
|
char *rx = NULL, *tx = NULL;
|
|
int ret = 0, count = 0;
|
|
struct spi_test *test;
|
|
|
|
/* allocate rx/tx buffers of 128kB size without devm
|
|
* in the hope that is on a page boundary
|
|
*/
|
|
if (use_vmalloc)
|
|
rx = vmalloc(SPI_TEST_MAX_SIZE_PLUS);
|
|
else
|
|
rx = kzalloc(SPI_TEST_MAX_SIZE_PLUS, GFP_KERNEL);
|
|
if (!rx)
|
|
return -ENOMEM;
|
|
|
|
|
|
if (use_vmalloc)
|
|
tx = vmalloc(SPI_TEST_MAX_SIZE_PLUS);
|
|
else
|
|
tx = kzalloc(SPI_TEST_MAX_SIZE_PLUS, GFP_KERNEL);
|
|
if (!tx) {
|
|
ret = -ENOMEM;
|
|
goto err_tx;
|
|
}
|
|
|
|
/* now run the individual tests in the table */
|
|
for (test = tests, count = 0; test->description[0];
|
|
test++, count++) {
|
|
/* only run test if requested */
|
|
if ((run_only_test > -1) && (count != run_only_test))
|
|
continue;
|
|
/* run custom implementation */
|
|
if (test->run_test)
|
|
ret = test->run_test(spi, test, tx, rx);
|
|
else
|
|
ret = spi_test_run_test(spi, test, tx, rx);
|
|
if (ret)
|
|
goto out;
|
|
/* add some delays so that we can easily
|
|
* detect the individual tests when using a logic analyzer
|
|
* we also add scheduling to avoid potential spi_timeouts...
|
|
*/
|
|
mdelay(100);
|
|
schedule();
|
|
}
|
|
|
|
out:
|
|
kvfree(tx);
|
|
err_tx:
|
|
kvfree(rx);
|
|
return ret;
|
|
}
|
|
EXPORT_SYMBOL_GPL(spi_test_run_tests);
|