mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-29 14:05:19 +08:00
9188883fd6
N900 now seems to shut down the external oscillator when hitting off-idle. And Beagle XM seems to have OSC_EN pin connected to allow shutting down the oscillator looking at the schematics. The oscillator output is cut off in off-idle and you can monitor it from R56 on the bottom side of the board near the power jack. Note that for beagle we need to also enable the UART wake-up event, the others have that enabled in earlier patches. OMAP37XX EVM (TMDSEVM3730) does not seem to have twl4030 clken pin connected, so there is no point trying to enable shutting down of the oscillator on it for the extra latency it adds. Signed-off-by: Tony Lindgren <tony@atomide.com>
130 lines
2.2 KiB
Plaintext
130 lines
2.2 KiB
Plaintext
/*
|
|
* Common support for omap3 EVM boards
|
|
*/
|
|
|
|
#include "omap-gpmc-smsc911x.dtsi"
|
|
|
|
/ {
|
|
cpus {
|
|
cpu@0 {
|
|
cpu0-supply = <&vcc>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
ledb {
|
|
label = "omap3evm::ledb";
|
|
gpios = <&twl_gpio 19 GPIO_ACTIVE_HIGH>; /* LEDB */
|
|
linux,default-trigger = "default-on";
|
|
};
|
|
};
|
|
|
|
wl12xx_vmmc: wl12xx_vmmc {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "vwl1271";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
gpio = <&gpio5 22 0>; /* gpio150 */
|
|
startup-delay-us = <70000>;
|
|
enable-active-high;
|
|
vin-supply = <&vmmc2>;
|
|
};
|
|
};
|
|
|
|
&i2c1 {
|
|
clock-frequency = <2600000>;
|
|
|
|
twl: twl@48 {
|
|
reg = <0x48>;
|
|
interrupts = <7>; /* SYS_NIRQ cascaded to intc */
|
|
interrupt-parent = <&intc>;
|
|
};
|
|
};
|
|
|
|
#include "twl4030.dtsi"
|
|
#include "twl4030_omap3.dtsi"
|
|
#include "omap3-panel-sharp-ls037v7dw01.dtsi"
|
|
|
|
&backlight0 {
|
|
gpios = <&twl_gpio 18 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
&twl {
|
|
twl_power: power {
|
|
compatible = "ti,twl4030-power-omap3-evm", "ti,twl4030-power-idle";
|
|
ti,use_poweroff;
|
|
};
|
|
};
|
|
|
|
&i2c2 {
|
|
clock-frequency = <400000>;
|
|
};
|
|
|
|
&i2c3 {
|
|
clock-frequency = <400000>;
|
|
|
|
/*
|
|
* TVP5146 Video decoder-in for analog input support.
|
|
*/
|
|
tvp5146@5c {
|
|
compatible = "ti,tvp5146m2";
|
|
reg = <0x5c>;
|
|
};
|
|
};
|
|
|
|
&lcd_3v3 {
|
|
gpio = <&gpio5 25 GPIO_ACTIVE_LOW>; /* gpio153 */
|
|
enable-active-low;
|
|
};
|
|
|
|
&lcd0 {
|
|
enable-gpios = <&gpio5 24 GPIO_ACTIVE_HIGH>; /* gpio152, lcd INI */
|
|
reset-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd RESB */
|
|
mode-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH /* gpio154, lcd MO */
|
|
&gpio1 2 GPIO_ACTIVE_HIGH /* gpio2, lcd LR */
|
|
&gpio1 3 GPIO_ACTIVE_HIGH>; /* gpio3, lcd UD */
|
|
};
|
|
|
|
&mcspi1 {
|
|
tsc2046@0 {
|
|
interrupt-parent = <&gpio6>;
|
|
interrupts = <15 0>; /* gpio175 */
|
|
pendown-gpio = <&gpio6 15 0>;
|
|
};
|
|
};
|
|
|
|
&mmc1 {
|
|
vmmc-supply = <&vmmc1>;
|
|
vmmc_aux-supply = <&vsim>;
|
|
bus-width = <8>;
|
|
};
|
|
|
|
&mmc2 {
|
|
vmmc-supply = <&wl12xx_vmmc>;
|
|
non-removable;
|
|
bus-width = <4>;
|
|
cap-power-off-card;
|
|
};
|
|
|
|
&twl_gpio {
|
|
ti,use-leds;
|
|
};
|
|
|
|
&usb_otg_hs {
|
|
interface-type = <0>;
|
|
usb-phy = <&usb2_phy>;
|
|
phys = <&usb2_phy>;
|
|
phy-names = "usb2-phy";
|
|
mode = <3>;
|
|
power = <50>;
|
|
};
|
|
|
|
&gpmc {
|
|
ethernet@gpmc {
|
|
interrupt-parent = <&gpio6>;
|
|
interrupts = <16 8>;
|
|
reg = <5 0 0xff>;
|
|
};
|
|
};
|