mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-23 11:04:44 +08:00
4da722ca19
Pretty much any node can have a status property, so it doesn't need to be in examples. Converted with the following command and removed examples with SoC and board specific splits: git grep -l -E 'status.*=.*' Documentation/devicetree/ | xargs sed -i -E '/\sstatus.*=.*"(disabled|ok|okay)/d' Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Rob Herring <robh@kernel.org>
84 lines
1.9 KiB
Plaintext
84 lines
1.9 KiB
Plaintext
NXP LPC1850 Reset Generation Unit (RGU)
|
|
========================================
|
|
|
|
Please also refer to reset.txt in this directory for common reset
|
|
controller binding usage.
|
|
|
|
Required properties:
|
|
- compatible: Should be "nxp,lpc1850-rgu"
|
|
- reg: register base and length
|
|
- clocks: phandle and clock specifier to RGU clocks
|
|
- clock-names: should contain "delay" and "reg"
|
|
- #reset-cells: should be 1
|
|
|
|
See table below for valid peripheral reset numbers. Numbers not
|
|
in the table below are either reserved or not applicable for
|
|
normal operation.
|
|
|
|
Reset Peripheral
|
|
9 System control unit (SCU)
|
|
12 ARM Cortex-M0 subsystem core (LPC43xx only)
|
|
13 CPU core
|
|
16 LCD controller
|
|
17 USB0
|
|
18 USB1
|
|
19 DMA
|
|
20 SDIO
|
|
21 External memory controller (EMC)
|
|
22 Ethernet
|
|
25 Flash bank A
|
|
27 EEPROM
|
|
28 GPIO
|
|
29 Flash bank B
|
|
32 Timer0
|
|
33 Timer1
|
|
34 Timer2
|
|
35 Timer3
|
|
36 Repetitive Interrupt timer (RIT)
|
|
37 State Configurable Timer (SCT)
|
|
38 Motor control PWM (MCPWM)
|
|
39 QEI
|
|
40 ADC0
|
|
41 ADC1
|
|
42 DAC
|
|
44 USART0
|
|
45 UART1
|
|
46 USART2
|
|
47 USART3
|
|
48 I2C0
|
|
49 I2C1
|
|
50 SSP0
|
|
51 SSP1
|
|
52 I2S0 and I2S1
|
|
53 Serial Flash Interface (SPIFI)
|
|
54 C_CAN1
|
|
55 C_CAN0
|
|
56 ARM Cortex-M0 application core (LPC4370 only)
|
|
57 SGPIO (LPC43xx only)
|
|
58 SPI (LPC43xx only)
|
|
60 ADCHS (12-bit ADC) (LPC4370 only)
|
|
|
|
Refer to NXP LPC18xx or LPC43xx user manual for more details about
|
|
the reset signals and the connected block/peripheral.
|
|
|
|
Reset provider example:
|
|
rgu: reset-controller@40053000 {
|
|
compatible = "nxp,lpc1850-rgu";
|
|
reg = <0x40053000 0x1000>;
|
|
clocks = <&cgu BASE_SAFE_CLK>, <&ccu1 CLK_CPU_BUS>;
|
|
clock-names = "delay", "reg";
|
|
#reset-cells = <1>;
|
|
};
|
|
|
|
Reset consumer example:
|
|
mac: ethernet@40010000 {
|
|
compatible = "nxp,lpc1850-dwmac", "snps,dwmac-3.611", "snps,dwmac";
|
|
reg = <0x40010000 0x2000>;
|
|
interrupts = <5>;
|
|
interrupt-names = "macirq";
|
|
clocks = <&ccu1 CLK_CPU_ETHERNET>;
|
|
clock-names = "stmmaceth";
|
|
resets = <&rgu 22>;
|
|
reset-names = "stmmaceth";
|
|
};
|