0
0
mirror of https://mirrors.bfsu.edu.cn/git/linux.git synced 2024-12-16 07:24:39 +08:00
linux/drivers/net/dsa/mv88e6131.c
Alexander Duyck b4d2394d01 dsa: Replace mii_bus with a generic host device
This change makes it so that instead of passing and storing a mii_bus we
instead pass and store a host_dev.  From there we can test to determine the
exact type of device, and can verify it is the correct device for our switch.

So for example it would be possible to pass a device pointer from a pci_dev
and instead of checking for a PHY ID we could check for a vendor and/or device
ID.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-15 17:24:20 -04:00

403 lines
11 KiB
C

/*
* net/dsa/mv88e6131.c - Marvell 88e6095/6095f/6131 switch chip support
* Copyright (c) 2008-2009 Marvell Semiconductor
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#include <linux/delay.h>
#include <linux/jiffies.h>
#include <linux/list.h>
#include <linux/module.h>
#include <linux/netdevice.h>
#include <linux/phy.h>
#include <net/dsa.h>
#include "mv88e6xxx.h"
/* Switch product IDs */
#define ID_6085 0x04a0
#define ID_6095 0x0950
#define ID_6131 0x1060
static char *mv88e6131_probe(struct device *host_dev, int sw_addr)
{
struct mii_bus *bus = dsa_host_dev_to_mii_bus(host_dev);
int ret;
if (bus == NULL)
return NULL;
ret = __mv88e6xxx_reg_read(bus, sw_addr, REG_PORT(0), 0x03);
if (ret >= 0) {
ret &= 0xfff0;
if (ret == ID_6085)
return "Marvell 88E6085";
if (ret == ID_6095)
return "Marvell 88E6095/88E6095F";
if (ret == ID_6131)
return "Marvell 88E6131";
}
return NULL;
}
static int mv88e6131_switch_reset(struct dsa_switch *ds)
{
int i;
int ret;
unsigned long timeout;
/* Set all ports to the disabled state. */
for (i = 0; i < 11; i++) {
ret = REG_READ(REG_PORT(i), 0x04);
REG_WRITE(REG_PORT(i), 0x04, ret & 0xfffc);
}
/* Wait for transmit queues to drain. */
usleep_range(2000, 4000);
/* Reset the switch. */
REG_WRITE(REG_GLOBAL, 0x04, 0xc400);
/* Wait up to one second for reset to complete. */
timeout = jiffies + 1 * HZ;
while (time_before(jiffies, timeout)) {
ret = REG_READ(REG_GLOBAL, 0x00);
if ((ret & 0xc800) == 0xc800)
break;
usleep_range(1000, 2000);
}
if (time_after(jiffies, timeout))
return -ETIMEDOUT;
return 0;
}
static int mv88e6131_setup_global(struct dsa_switch *ds)
{
int ret;
int i;
/* Enable the PHY polling unit, don't discard packets with
* excessive collisions, use a weighted fair queueing scheme
* to arbitrate between packet queues, set the maximum frame
* size to 1632, and mask all interrupt sources.
*/
REG_WRITE(REG_GLOBAL, 0x04, 0x4400);
/* Set the default address aging time to 5 minutes, and
* enable address learn messages to be sent to all message
* ports.
*/
REG_WRITE(REG_GLOBAL, 0x0a, 0x0148);
/* Configure the priority mapping registers. */
ret = mv88e6xxx_config_prio(ds);
if (ret < 0)
return ret;
/* Set the VLAN ethertype to 0x8100. */
REG_WRITE(REG_GLOBAL, 0x19, 0x8100);
/* Disable ARP mirroring, and configure the upstream port as
* the port to which ingress and egress monitor frames are to
* be sent.
*/
REG_WRITE(REG_GLOBAL, 0x1a, (dsa_upstream_port(ds) * 0x1100) | 0x00f0);
/* Disable cascade port functionality unless this device
* is used in a cascade configuration, and set the switch's
* DSA device number.
*/
if (ds->dst->pd->nr_chips > 1)
REG_WRITE(REG_GLOBAL, 0x1c, 0xf000 | (ds->index & 0x1f));
else
REG_WRITE(REG_GLOBAL, 0x1c, 0xe000 | (ds->index & 0x1f));
/* Send all frames with destination addresses matching
* 01:80:c2:00:00:0x to the CPU port.
*/
REG_WRITE(REG_GLOBAL2, 0x03, 0xffff);
/* Ignore removed tag data on doubly tagged packets, disable
* flow control messages, force flow control priority to the
* highest, and send all special multicast frames to the CPU
* port at the highest priority.
*/
REG_WRITE(REG_GLOBAL2, 0x05, 0x00ff);
/* Program the DSA routing table. */
for (i = 0; i < 32; i++) {
int nexthop;
nexthop = 0x1f;
if (i != ds->index && i < ds->dst->pd->nr_chips)
nexthop = ds->pd->rtable[i] & 0x1f;
REG_WRITE(REG_GLOBAL2, 0x06, 0x8000 | (i << 8) | nexthop);
}
/* Clear all trunk masks. */
for (i = 0; i < 8; i++)
REG_WRITE(REG_GLOBAL2, 0x07, 0x8000 | (i << 12) | 0x7ff);
/* Clear all trunk mappings. */
for (i = 0; i < 16; i++)
REG_WRITE(REG_GLOBAL2, 0x08, 0x8000 | (i << 11));
/* Force the priority of IGMP/MLD snoop frames and ARP frames
* to the highest setting.
*/
REG_WRITE(REG_GLOBAL2, 0x0f, 0x00ff);
return 0;
}
static int mv88e6131_setup_port(struct dsa_switch *ds, int p)
{
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
int addr = REG_PORT(p);
u16 val;
/* MAC Forcing register: don't force link, speed, duplex
* or flow control state to any particular values on physical
* ports, but force the CPU port and all DSA ports to 1000 Mb/s
* (100 Mb/s on 6085) full duplex.
*/
if (dsa_is_cpu_port(ds, p) || ds->dsa_port_mask & (1 << p))
if (ps->id == ID_6085)
REG_WRITE(addr, 0x01, 0x003d); /* 100 Mb/s */
else
REG_WRITE(addr, 0x01, 0x003e); /* 1000 Mb/s */
else
REG_WRITE(addr, 0x01, 0x0003);
/* Port Control: disable Core Tag, disable Drop-on-Lock,
* transmit frames unmodified, disable Header mode,
* enable IGMP/MLD snoop, disable DoubleTag, disable VLAN
* tunneling, determine priority by looking at 802.1p and
* IP priority fields (IP prio has precedence), and set STP
* state to Forwarding.
*
* If this is the upstream port for this switch, enable
* forwarding of unknown unicasts, and enable DSA tagging
* mode.
*
* If this is the link to another switch, use DSA tagging
* mode, but do not enable forwarding of unknown unicasts.
*/
val = 0x0433;
if (p == dsa_upstream_port(ds)) {
val |= 0x0104;
/* On 6085, unknown multicast forward is controlled
* here rather than in Port Control 2 register.
*/
if (ps->id == ID_6085)
val |= 0x0008;
}
if (ds->dsa_port_mask & (1 << p))
val |= 0x0100;
REG_WRITE(addr, 0x04, val);
/* Port Control 1: disable trunking. Also, if this is the
* CPU port, enable learn messages to be sent to this port.
*/
REG_WRITE(addr, 0x05, dsa_is_cpu_port(ds, p) ? 0x8000 : 0x0000);
/* Port based VLAN map: give each port its own address
* database, allow the CPU port to talk to each of the 'real'
* ports, and allow each of the 'real' ports to only talk to
* the upstream port.
*/
val = (p & 0xf) << 12;
if (dsa_is_cpu_port(ds, p))
val |= ds->phys_port_mask;
else
val |= 1 << dsa_upstream_port(ds);
REG_WRITE(addr, 0x06, val);
/* Default VLAN ID and priority: don't set a default VLAN
* ID, and set the default packet priority to zero.
*/
REG_WRITE(addr, 0x07, 0x0000);
/* Port Control 2: don't force a good FCS, don't use
* VLAN-based, source address-based or destination
* address-based priority overrides, don't let the switch
* add or strip 802.1q tags, don't discard tagged or
* untagged frames on this port, do a destination address
* lookup on received packets as usual, don't send a copy
* of all transmitted/received frames on this port to the
* CPU, and configure the upstream port number.
*
* If this is the upstream port for this switch, enable
* forwarding of unknown multicast addresses.
*/
if (ps->id == ID_6085)
/* on 6085, bits 3:0 are reserved, bit 6 control ARP
* mirroring, and multicast forward is handled in
* Port Control register.
*/
REG_WRITE(addr, 0x08, 0x0080);
else {
val = 0x0080 | dsa_upstream_port(ds);
if (p == dsa_upstream_port(ds))
val |= 0x0040;
REG_WRITE(addr, 0x08, val);
}
/* Rate Control: disable ingress rate limiting. */
REG_WRITE(addr, 0x09, 0x0000);
/* Rate Control 2: disable egress rate limiting. */
REG_WRITE(addr, 0x0a, 0x0000);
/* Port Association Vector: when learning source addresses
* of packets, add the address to the address database using
* a port bitmap that has only the bit for this port set and
* the other bits clear.
*/
REG_WRITE(addr, 0x0b, 1 << p);
/* Tag Remap: use an identity 802.1p prio -> switch prio
* mapping.
*/
REG_WRITE(addr, 0x18, 0x3210);
/* Tag Remap 2: use an identity 802.1p prio -> switch prio
* mapping.
*/
REG_WRITE(addr, 0x19, 0x7654);
return 0;
}
static int mv88e6131_setup(struct dsa_switch *ds)
{
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
int i;
int ret;
mutex_init(&ps->smi_mutex);
mv88e6xxx_ppu_state_init(ds);
mutex_init(&ps->stats_mutex);
ps->id = REG_READ(REG_PORT(0), 0x03) & 0xfff0;
ret = mv88e6131_switch_reset(ds);
if (ret < 0)
return ret;
/* @@@ initialise vtu and atu */
ret = mv88e6131_setup_global(ds);
if (ret < 0)
return ret;
for (i = 0; i < 11; i++) {
ret = mv88e6131_setup_port(ds, i);
if (ret < 0)
return ret;
}
return 0;
}
static int mv88e6131_port_to_phy_addr(int port)
{
if (port >= 0 && port <= 11)
return port;
return -1;
}
static int
mv88e6131_phy_read(struct dsa_switch *ds, int port, int regnum)
{
int addr = mv88e6131_port_to_phy_addr(port);
return mv88e6xxx_phy_read_ppu(ds, addr, regnum);
}
static int
mv88e6131_phy_write(struct dsa_switch *ds,
int port, int regnum, u16 val)
{
int addr = mv88e6131_port_to_phy_addr(port);
return mv88e6xxx_phy_write_ppu(ds, addr, regnum, val);
}
static struct mv88e6xxx_hw_stat mv88e6131_hw_stats[] = {
{ "in_good_octets", 8, 0x00, },
{ "in_bad_octets", 4, 0x02, },
{ "in_unicast", 4, 0x04, },
{ "in_broadcasts", 4, 0x06, },
{ "in_multicasts", 4, 0x07, },
{ "in_pause", 4, 0x16, },
{ "in_undersize", 4, 0x18, },
{ "in_fragments", 4, 0x19, },
{ "in_oversize", 4, 0x1a, },
{ "in_jabber", 4, 0x1b, },
{ "in_rx_error", 4, 0x1c, },
{ "in_fcs_error", 4, 0x1d, },
{ "out_octets", 8, 0x0e, },
{ "out_unicast", 4, 0x10, },
{ "out_broadcasts", 4, 0x13, },
{ "out_multicasts", 4, 0x12, },
{ "out_pause", 4, 0x15, },
{ "excessive", 4, 0x11, },
{ "collisions", 4, 0x1e, },
{ "deferred", 4, 0x05, },
{ "single", 4, 0x14, },
{ "multiple", 4, 0x17, },
{ "out_fcs_error", 4, 0x03, },
{ "late", 4, 0x1f, },
{ "hist_64bytes", 4, 0x08, },
{ "hist_65_127bytes", 4, 0x09, },
{ "hist_128_255bytes", 4, 0x0a, },
{ "hist_256_511bytes", 4, 0x0b, },
{ "hist_512_1023bytes", 4, 0x0c, },
{ "hist_1024_max_bytes", 4, 0x0d, },
};
static void
mv88e6131_get_strings(struct dsa_switch *ds, int port, uint8_t *data)
{
mv88e6xxx_get_strings(ds, ARRAY_SIZE(mv88e6131_hw_stats),
mv88e6131_hw_stats, port, data);
}
static void
mv88e6131_get_ethtool_stats(struct dsa_switch *ds,
int port, uint64_t *data)
{
mv88e6xxx_get_ethtool_stats(ds, ARRAY_SIZE(mv88e6131_hw_stats),
mv88e6131_hw_stats, port, data);
}
static int mv88e6131_get_sset_count(struct dsa_switch *ds)
{
return ARRAY_SIZE(mv88e6131_hw_stats);
}
struct dsa_switch_driver mv88e6131_switch_driver = {
.tag_protocol = DSA_TAG_PROTO_DSA,
.priv_size = sizeof(struct mv88e6xxx_priv_state),
.probe = mv88e6131_probe,
.setup = mv88e6131_setup,
.set_addr = mv88e6xxx_set_addr_direct,
.phy_read = mv88e6131_phy_read,
.phy_write = mv88e6131_phy_write,
.poll_link = mv88e6xxx_poll_link,
.get_strings = mv88e6131_get_strings,
.get_ethtool_stats = mv88e6131_get_ethtool_stats,
.get_sset_count = mv88e6131_get_sset_count,
};
MODULE_ALIAS("platform:mv88e6085");
MODULE_ALIAS("platform:mv88e6095");
MODULE_ALIAS("platform:mv88e6095f");
MODULE_ALIAS("platform:mv88e6131");