mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-14 22:44:27 +08:00
928af22477
Add group configuration for uarts that are cut down variants, the standard being full, i.e. all signals, flow control, i.e. rx/tx and cts/rts, and rx/tx only. This allows us to be more precise in which pins we're actually using. Unfortunately the existing naming scheme leaves things to be desired, e.g. uart3grp0 means RX/TX and CTS/RTS, yet uart0grp0 means all pins. Since the exising suffixes have different meaning for different uarts, and the fact that we cannot change the name of existing groups, makes it hard to use a descriptive name for the newly added groups. Signed-off-by: Niklas Cassel <niklas.cassel@axis.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
88 lines
2.5 KiB
Plaintext
88 lines
2.5 KiB
Plaintext
Axis ARTPEC-6 Pin Controller
|
|
|
|
Required properties:
|
|
- compatible: "axis,artpec6-pinctrl".
|
|
- reg: Should contain the register physical address and length for the pin
|
|
controller.
|
|
|
|
A pinctrl node should contain at least one subnode representing the pinctrl
|
|
groups available on the machine. Each subnode will list the mux function
|
|
required and what pin group it will use. Each subnode will also configure the
|
|
drive strength and bias pullup of the pin group. If either of these options is
|
|
not set, its actual value will be unspecified.
|
|
|
|
|
|
Required subnode-properties:
|
|
- function: Function to mux.
|
|
- groups: Name of the pin group to use for the function above.
|
|
|
|
Available functions and groups (function: group0, group1...):
|
|
gpio: cpuclkoutgrp0, udlclkoutgrp0, i2c1grp0, i2c2grp0,
|
|
i2c3grp0, i2s0grp0, i2s1grp0, i2srefclkgrp0, spi0grp0,
|
|
spi1grp0, pciedebuggrp0, uart0grp0, uart0grp1, uart0grp2,
|
|
uart1grp0, uart1grp1, uart2grp0, uart2grp1, uart2grp2,
|
|
uart3grp0, uart4grp0, uart4grp1, uart5grp0, uart5grp1,
|
|
uart5nocts
|
|
cpuclkout: cpuclkoutgrp0
|
|
udlclkout: udlclkoutgrp0
|
|
i2c1: i2c1grp0
|
|
i2c2: i2c2grp0
|
|
i2c3: i2c3grp0
|
|
i2s0: i2s0grp0
|
|
i2s1: i2s1grp0
|
|
i2srefclk: i2srefclkgrp0
|
|
spi0: spi0grp0
|
|
spi1: spi1grp0
|
|
pciedebug: pciedebuggrp0
|
|
uart0: uart0grp0, uart0grp1, uart0grp2
|
|
uart1: uart1grp0, uart1grp1
|
|
uart2: uart2grp0, uart2grp1, uart2grp2
|
|
uart3: uart3grp0
|
|
uart4: uart4grp0, uart4grp1
|
|
uart5: uart5grp0, uart5grp1, uart5nocts
|
|
nand: nandgrp0
|
|
sdio0: sdio0grp0
|
|
sdio1: sdio1grp0
|
|
ethernet: ethernetgrp0
|
|
|
|
|
|
Optional subnode-properties (see pinctrl-bindings.txt):
|
|
- drive-strength: 4, 6, 8, 9 mA. For SD and NAND pins, this is for 3.3V VCCQ3.
|
|
- bias-pull-up
|
|
- bias-disable
|
|
|
|
Examples:
|
|
pinctrl@f801d000 {
|
|
compatible = "axis,artpec6-pinctrl";
|
|
reg = <0xf801d000 0x400>;
|
|
|
|
pinctrl_uart0: uart0grp {
|
|
function = "uart0";
|
|
groups = "uart0grp0";
|
|
drive-strength = <4>;
|
|
bias-pull-up;
|
|
};
|
|
pinctrl_uart3: uart3grp {
|
|
function = "uart3";
|
|
groups = "uart3grp0";
|
|
};
|
|
};
|
|
uart0: uart@f8036000 {
|
|
compatible = "arm,pl011", "arm,primecell";
|
|
reg = <0xf8036000 0x1000>;
|
|
interrupts = <0 104 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&pll2div24>, <&apb_pclk>;
|
|
clock-names = "uart_clk", "apb_pclk";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_uart0>;
|
|
};
|
|
uart3: uart@f8039000 {
|
|
compatible = "arm,pl011", "arm,primecell";
|
|
reg = <0xf8039000 0x1000>;
|
|
interrupts = <0 128 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&pll2div24>, <&apb_pclk>;
|
|
clock-names = "uart_clk", "apb_pclk";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_uart3>;
|
|
};
|