mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-24 03:24:55 +08:00
05d86a0ae8
This adds the gpio-ranges property so that the GPIO pins are initialized by the GPIO framework and not pinctrl. This fixes a circular dependency between these two frameworks so GPIO hogging can be used on this board. This was not tested on this particular hardware, however this same change was tested on qcom-pm8941 using a LG Nexus 5 (hammerhead) phone. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Andy Gross <agross@kernel.org>
101 lines
2.2 KiB
Plaintext
101 lines
2.2 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
#include <dt-bindings/iio/qcom,spmi-vadc.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/spmi/spmi.h>
|
|
|
|
&spmi_bus {
|
|
|
|
pma8084_0: pma8084@0 {
|
|
compatible = "qcom,pma8084", "qcom,spmi-pmic";
|
|
reg = <0x0 SPMI_USID>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
rtc@6000 {
|
|
compatible = "qcom,pm8941-rtc";
|
|
reg = <0x6000>,
|
|
<0x6100>;
|
|
reg-names = "rtc", "alarm";
|
|
interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
|
|
};
|
|
|
|
pwrkey@800 {
|
|
compatible = "qcom,pm8941-pwrkey";
|
|
reg = <0x800>;
|
|
interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
|
|
debounce = <15625>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
pma8084_gpios: gpios@c000 {
|
|
compatible = "qcom,pma8084-gpio", "qcom,spmi-gpio";
|
|
reg = <0xc000>;
|
|
gpio-controller;
|
|
gpio-ranges = <&pma8084_gpios 0 0 22>;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
pma8084_mpps: mpps@a000 {
|
|
compatible = "qcom,pma8084-mpp", "qcom,spmi-mpp";
|
|
reg = <0xa000>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupts = <0 0xa0 0 IRQ_TYPE_NONE>,
|
|
<0 0xa1 0 IRQ_TYPE_NONE>,
|
|
<0 0xa2 0 IRQ_TYPE_NONE>,
|
|
<0 0xa3 0 IRQ_TYPE_NONE>,
|
|
<0 0xa4 0 IRQ_TYPE_NONE>,
|
|
<0 0xa5 0 IRQ_TYPE_NONE>,
|
|
<0 0xa6 0 IRQ_TYPE_NONE>,
|
|
<0 0xa7 0 IRQ_TYPE_NONE>;
|
|
};
|
|
|
|
pma8084_temp: temp-alarm@2400 {
|
|
compatible = "qcom,spmi-temp-alarm";
|
|
reg = <0x2400>;
|
|
interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
|
|
#thermal-sensor-cells = <0>;
|
|
io-channels = <&pma8084_vadc VADC_DIE_TEMP>;
|
|
io-channel-names = "thermal";
|
|
};
|
|
|
|
pma8084_vadc: vadc@3100 {
|
|
compatible = "qcom,spmi-vadc";
|
|
reg = <0x3100>;
|
|
interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
#io-channel-cells = <1>;
|
|
io-channel-ranges;
|
|
|
|
die_temp {
|
|
reg = <VADC_DIE_TEMP>;
|
|
};
|
|
ref_625mv {
|
|
reg = <VADC_REF_625MV>;
|
|
};
|
|
ref_1250v {
|
|
reg = <VADC_REF_1250MV>;
|
|
};
|
|
ref_buf_625mv {
|
|
reg = <VADC_SPARE1>;
|
|
};
|
|
ref_gnd {
|
|
reg = <VADC_GND_REF>;
|
|
};
|
|
ref_vdd {
|
|
reg = <VADC_VDD_VADC>;
|
|
};
|
|
};
|
|
};
|
|
|
|
pma8084_1: pma8084@1 {
|
|
compatible = "qcom,pma8084", "qcom,spmi-pmic";
|
|
reg = <0x1 SPMI_USID>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
};
|
|
};
|