mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-24 03:24:55 +08:00
0fd5ff9e4c
The Universal C210 (Exynos4210) uses the secure interface of MDMA0, instead of regular one - non-secure MDMA1. DTS was overriding MDMA1 node address which caused DTC W=1 warning: arch/arm/boot/dts/exynos4.dtsi:707.25-716.6: Warning (simple_bus_reg): /soc/amba/mdma@12850000: simple-bus unit address format error, expected "12840000" Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
605 lines
12 KiB
Plaintext
605 lines
12 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Samsung's Exynos4210 based Universal C210 board device tree source
|
|
*
|
|
* Copyright (c) 2012-2013 Samsung Electronics Co., Ltd.
|
|
* http://www.samsung.com
|
|
*
|
|
* Device tree source file for Samsung's Universal C210 board which is based on
|
|
* Samsung's Exynos4210 rev0 SoC.
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include "exynos4210.dtsi"
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
/ {
|
|
model = "Samsung Universal C210 based on Exynos4210 rev0";
|
|
compatible = "samsung,universal_c210", "samsung,exynos4210", "samsung,exynos4";
|
|
|
|
memory@40000000 {
|
|
device_type = "memory";
|
|
reg = <0x40000000 0x10000000
|
|
0x50000000 0x10000000>;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "root=/dev/mmcblk0p5 rw rootwait earlyprintk panic=5 maxcpus=1";
|
|
stdout-path = "serial2:115200n8";
|
|
};
|
|
|
|
|
|
fixed-rate-clocks {
|
|
xxti {
|
|
compatible = "samsung,clock-xxti";
|
|
clock-frequency = <0>;
|
|
};
|
|
|
|
xusbxti {
|
|
compatible = "samsung,clock-xusbxti";
|
|
clock-frequency = <24000000>;
|
|
};
|
|
};
|
|
|
|
vemmc_reg: voltage-regulator {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "VMEM_VDD_2_8V";
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
gpio = <&gpe1 3 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys";
|
|
|
|
vol-up-key {
|
|
gpios = <&gpx2 0 GPIO_ACTIVE_LOW>;
|
|
linux,code = <115>;
|
|
label = "volume up";
|
|
debounce-interval = <1>;
|
|
};
|
|
|
|
vol-down-key {
|
|
gpios = <&gpx2 1 GPIO_ACTIVE_LOW>;
|
|
linux,code = <114>;
|
|
label = "volume down";
|
|
debounce-interval = <1>;
|
|
};
|
|
|
|
config-key {
|
|
gpios = <&gpx2 2 GPIO_ACTIVE_LOW>;
|
|
linux,code = <171>;
|
|
label = "config";
|
|
debounce-interval = <1>;
|
|
wakeup-source;
|
|
};
|
|
|
|
camera-key {
|
|
gpios = <&gpx2 3 GPIO_ACTIVE_LOW>;
|
|
linux,code = <212>;
|
|
label = "camera";
|
|
debounce-interval = <1>;
|
|
};
|
|
|
|
power-key {
|
|
gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
|
|
linux,code = <116>;
|
|
label = "power";
|
|
debounce-interval = <1>;
|
|
wakeup-source;
|
|
};
|
|
|
|
ok-key {
|
|
gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
|
|
linux,code = <352>;
|
|
label = "ok";
|
|
debounce-interval = <1>;
|
|
};
|
|
};
|
|
|
|
tsp_reg: voltage-regulator {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "TSP_2_8V";
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
gpio = <&gpe2 3 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
};
|
|
|
|
spi-lcd {
|
|
compatible = "spi-gpio";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
gpio-sck = <&gpy3 1 GPIO_ACTIVE_HIGH>;
|
|
gpio-mosi = <&gpy3 3 GPIO_ACTIVE_HIGH>;
|
|
num-chipselects = <1>;
|
|
cs-gpios = <&gpy4 3 GPIO_ACTIVE_HIGH>;
|
|
|
|
lcd@0 {
|
|
compatible = "samsung,ld9040";
|
|
reg = <0>;
|
|
vdd3-supply = <&ldo7_reg>;
|
|
vci-supply = <&ldo17_reg>;
|
|
reset-gpios = <&gpy4 5 GPIO_ACTIVE_HIGH>;
|
|
spi-max-frequency = <1200000>;
|
|
spi-cpol;
|
|
spi-cpha;
|
|
power-on-delay = <10>;
|
|
reset-delay = <10>;
|
|
panel-width-mm = <90>;
|
|
panel-height-mm = <154>;
|
|
display-timings {
|
|
timing {
|
|
clock-frequency = <23492370>;
|
|
hactive = <480>;
|
|
vactive = <800>;
|
|
hback-porch = <16>;
|
|
hfront-porch = <16>;
|
|
vback-porch = <2>;
|
|
vfront-porch = <28>;
|
|
hsync-len = <2>;
|
|
vsync-len = <1>;
|
|
hsync-active = <0>;
|
|
vsync-active = <0>;
|
|
de-active = <0>;
|
|
pixelclk-active = <0>;
|
|
};
|
|
};
|
|
port {
|
|
lcd_ep: endpoint {
|
|
remote-endpoint = <&fimd_dpi_ep>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
hdmi_en: voltage-regulator-hdmi-5v {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "HDMI_5V";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
gpio = <&gpe0 1 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
};
|
|
|
|
hdmi_ddc: i2c-ddc {
|
|
compatible = "i2c-gpio";
|
|
gpios = <&gpe4 2 GPIO_ACTIVE_HIGH &gpe4 3 GPIO_ACTIVE_HIGH>;
|
|
i2c-gpio,delay-us = <100>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pinctrl-0 = <&i2c_ddc_bus>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&amba {
|
|
mdma0: mdma@12840000 {
|
|
compatible = "arm,pl330", "arm,primecell";
|
|
reg = <0x12840000 0x1000>;
|
|
interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&clock CLK_MDMA>;
|
|
clock-names = "apb_pclk";
|
|
#dma-cells = <1>;
|
|
#dma-channels = <8>;
|
|
#dma-requests = <1>;
|
|
power-domains = <&pd_lcd0>;
|
|
};
|
|
};
|
|
|
|
&camera {
|
|
status = "okay";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <>;
|
|
};
|
|
|
|
&cpu0 {
|
|
cpu0-supply = <&vdd_arm_reg>;
|
|
};
|
|
|
|
&ehci {
|
|
status = "okay";
|
|
port@0 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&exynos_usbphy {
|
|
status = "okay";
|
|
vbus-supply = <&safeout1_reg>;
|
|
};
|
|
|
|
&fimc_0 {
|
|
status = "okay";
|
|
assigned-clocks = <&clock CLK_MOUT_FIMC0>,
|
|
<&clock CLK_SCLK_FIMC0>;
|
|
assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
|
|
assigned-clock-rates = <0>, <160000000>;
|
|
};
|
|
|
|
&fimc_1 {
|
|
status = "okay";
|
|
assigned-clocks = <&clock CLK_MOUT_FIMC1>,
|
|
<&clock CLK_SCLK_FIMC1>;
|
|
assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
|
|
assigned-clock-rates = <0>, <160000000>;
|
|
};
|
|
|
|
&fimc_2 {
|
|
status = "okay";
|
|
assigned-clocks = <&clock CLK_MOUT_FIMC2>,
|
|
<&clock CLK_SCLK_FIMC2>;
|
|
assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
|
|
assigned-clock-rates = <0>, <160000000>;
|
|
};
|
|
|
|
&fimc_3 {
|
|
status = "okay";
|
|
assigned-clocks = <&clock CLK_MOUT_FIMC3>,
|
|
<&clock CLK_SCLK_FIMC3>;
|
|
assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
|
|
assigned-clock-rates = <0>, <160000000>;
|
|
};
|
|
|
|
&fimd {
|
|
pinctrl-0 = <&lcd_clk>, <&lcd_data24>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
samsung,invert-vden;
|
|
samsung,invert-vclk;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
port@3 {
|
|
reg = <3>;
|
|
fimd_dpi_ep: endpoint {
|
|
remote-endpoint = <&lcd_ep>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&hdmi {
|
|
hpd-gpios = <&gpx3 7 GPIO_ACTIVE_HIGH>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&hdmi_hpd>;
|
|
hdmi-en-supply = <&hdmi_en>;
|
|
vdd-supply = <&ldo3_reg>;
|
|
vdd_osc-supply = <&ldo4_reg>;
|
|
vdd_pll-supply = <&ldo3_reg>;
|
|
ddc = <&hdmi_ddc>;
|
|
status = "okay";
|
|
};
|
|
|
|
&hsotg {
|
|
vusb_d-supply = <&ldo3_reg>;
|
|
vusb_a-supply = <&ldo8_reg>;
|
|
dr_mode = "peripheral";
|
|
status = "okay";
|
|
};
|
|
|
|
&i2c_3 {
|
|
samsung,i2c-sda-delay = <100>;
|
|
samsung,i2c-slave-addr = <0x10>;
|
|
samsung,i2c-max-bus-freq = <100000>;
|
|
pinctrl-0 = <&i2c3_bus>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
|
|
tsp@4a {
|
|
/* TBD: Atmel maXtouch touchscreen */
|
|
reg = <0x4a>;
|
|
};
|
|
};
|
|
|
|
&i2c_5 {
|
|
samsung,i2c-sda-delay = <100>;
|
|
samsung,i2c-slave-addr = <0x10>;
|
|
samsung,i2c-max-bus-freq = <100000>;
|
|
pinctrl-0 = <&i2c5_bus>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
|
|
vdd_arm_reg: pmic@60 {
|
|
compatible = "maxim,max8952";
|
|
reg = <0x60>;
|
|
|
|
max8952,vid-gpios = <&gpx0 3 GPIO_ACTIVE_HIGH>,
|
|
<&gpx0 4 GPIO_ACTIVE_HIGH>;
|
|
max8952,default-mode = <0>;
|
|
max8952,dvs-mode-microvolt = <1250000>, <1200000>,
|
|
<1050000>, <950000>;
|
|
max8952,sync-freq = <0>;
|
|
max8952,ramp-speed = <0>;
|
|
|
|
regulator-name = "vdd_arm";
|
|
regulator-min-microvolt = <770000>;
|
|
regulator-max-microvolt = <1400000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
pmic@66 {
|
|
compatible = "national,lp3974";
|
|
interrupts-extended = <&gpx0 7 0>, <&gpx2 7 0>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&lp3974_irq>;
|
|
reg = <0x66>;
|
|
|
|
max8998,pmic-buck1-default-dvs-idx = <0>;
|
|
max8998,pmic-buck1-dvs-gpios = <&gpx0 5 GPIO_ACTIVE_HIGH>,
|
|
<&gpx0 6 GPIO_ACTIVE_HIGH>;
|
|
max8998,pmic-buck1-dvs-voltage = <1100000>, <1000000>,
|
|
<1100000>, <1000000>;
|
|
|
|
max8998,pmic-buck2-default-dvs-idx = <0>;
|
|
max8998,pmic-buck2-dvs-gpio = <&gpe2 0 GPIO_ACTIVE_HIGH>;
|
|
max8998,pmic-buck2-dvs-voltage = <1200000>, <1100000>;
|
|
|
|
regulators {
|
|
ldo2_reg: LDO2 {
|
|
regulator-name = "VALIVE_1.2V";
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
ldo3_reg: LDO3 {
|
|
regulator-name = "VUSB+MIPI_1.1V";
|
|
regulator-min-microvolt = <1100000>;
|
|
regulator-max-microvolt = <1100000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
ldo4_reg: LDO4 {
|
|
regulator-name = "VADC_3.3V";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
|
|
ldo5_reg: LDO5 {
|
|
regulator-name = "VTF_2.8V";
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
};
|
|
|
|
ldo6_reg: LDO6 {
|
|
regulator-name = "LDO6";
|
|
regulator-min-microvolt = <2000000>;
|
|
regulator-max-microvolt = <2000000>;
|
|
};
|
|
|
|
ldo7_reg: LDO7 {
|
|
regulator-name = "VLCD+VMIPI_1.8V";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
};
|
|
|
|
ldo8_reg: LDO8 {
|
|
regulator-name = "VUSB+VDAC_3.3V";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
ldo9_reg: LDO9 {
|
|
regulator-name = "VCC_2.8V";
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
ldo10_reg: LDO10 {
|
|
regulator-name = "VPLL_1.1V";
|
|
regulator-min-microvolt = <1100000>;
|
|
regulator-max-microvolt = <1100000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
ldo11_reg: LDO11 {
|
|
regulator-name = "CAM_AF_3.3V";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
|
|
ldo12_reg: LDO12 {
|
|
regulator-name = "PS_2.8V";
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
};
|
|
|
|
ldo13_reg: LDO13 {
|
|
regulator-name = "VHIC_1.2V";
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
};
|
|
|
|
ldo14_reg: LDO14 {
|
|
regulator-name = "CAM_I_HOST_1.8V";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
};
|
|
|
|
ldo15_reg: LDO15 {
|
|
regulator-name = "CAM_S_DIG+FM33_CORE_1.2V";
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
};
|
|
|
|
ldo16_reg: LDO16 {
|
|
regulator-name = "CAM_S_ANA_2.8V";
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
};
|
|
|
|
ldo17_reg: LDO17 {
|
|
regulator-name = "VCC_3.0V_LCD";
|
|
regulator-min-microvolt = <3000000>;
|
|
regulator-max-microvolt = <3000000>;
|
|
};
|
|
|
|
buck1_reg: BUCK1 {
|
|
regulator-name = "VINT_1.1V";
|
|
regulator-min-microvolt = <750000>;
|
|
regulator-max-microvolt = <1500000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
buck2_reg: BUCK2 {
|
|
regulator-name = "VG3D_1.1V";
|
|
regulator-min-microvolt = <750000>;
|
|
regulator-max-microvolt = <1500000>;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
buck3_reg: BUCK3 {
|
|
regulator-name = "VCC_1.8V";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
buck4_reg: BUCK4 {
|
|
regulator-name = "VMEM_1.2V";
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
ap32khz_reg: EN32KHz-AP {
|
|
regulator-name = "32KHz AP";
|
|
regulator-always-on;
|
|
};
|
|
|
|
cp32khz_reg: EN32KHz-CP {
|
|
regulator-name = "32KHz CP";
|
|
};
|
|
|
|
vichg_reg: ENVICHG {
|
|
regulator-name = "VICHG";
|
|
};
|
|
|
|
safeout1_reg: ESAFEOUT1 {
|
|
regulator-name = "SAFEOUT1";
|
|
};
|
|
|
|
safeout2_reg: ESAFEOUT2 {
|
|
regulator-name = "SAFEOUT2";
|
|
regulator-boot-on;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&i2c_8 {
|
|
status = "okay";
|
|
};
|
|
|
|
&mct {
|
|
compatible = "none";
|
|
};
|
|
|
|
&mdma1 {
|
|
/* Use the secure mdma0 */
|
|
status = "disabled";
|
|
};
|
|
|
|
&mixer {
|
|
status = "okay";
|
|
};
|
|
|
|
&ohci {
|
|
status = "okay";
|
|
port@0 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&pinctrl_1 {
|
|
lp3974_irq: lp3974-irq {
|
|
samsung,pins = "gpx0-7", "gpx2-7";
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
|
|
};
|
|
|
|
hdmi_hpd: hdmi-hpd {
|
|
samsung,pins = "gpx3-7";
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
|
|
};
|
|
};
|
|
|
|
&pinctrl_0 {
|
|
i2c_ddc_bus: i2c-ddc-bus {
|
|
samsung,pins = "gpe4-2", "gpe4-3";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
|
|
samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
|
|
};
|
|
};
|
|
|
|
&pwm {
|
|
compatible = "samsung,s5p6440-pwm";
|
|
status = "okay";
|
|
};
|
|
|
|
&sdhci_0 {
|
|
bus-width = <8>;
|
|
non-removable;
|
|
pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>;
|
|
pinctrl-names = "default";
|
|
vmmc-supply = <&vemmc_reg>;
|
|
status = "okay";
|
|
};
|
|
|
|
&sdhci_2 {
|
|
bus-width = <4>;
|
|
pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>;
|
|
pinctrl-names = "default";
|
|
vmmc-supply = <&ldo5_reg>;
|
|
cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>;
|
|
status = "okay";
|
|
};
|
|
|
|
&serial_0 {
|
|
status = "okay";
|
|
/delete-property/dmas;
|
|
/delete-property/dma-names;
|
|
};
|
|
|
|
&serial_1 {
|
|
status = "okay";
|
|
/delete-property/dmas;
|
|
/delete-property/dma-names;
|
|
};
|
|
|
|
&serial_2 {
|
|
status = "okay";
|
|
/delete-property/dmas;
|
|
/delete-property/dma-names;
|
|
};
|
|
|
|
&serial_3 {
|
|
status = "okay";
|
|
/delete-property/dmas;
|
|
/delete-property/dma-names;
|
|
};
|
|
|
|
&sysram {
|
|
smp-sysram@0 {
|
|
status = "disabled";
|
|
};
|
|
|
|
smp-sysram@5000 {
|
|
compatible = "samsung,exynos4210-sysram";
|
|
reg = <0x5000 0x1000>;
|
|
};
|
|
|
|
smp-sysram@1f000 {
|
|
status = "disabled";
|
|
};
|
|
};
|