linux/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts
Rob Herring abe60a3a7a ARM: dts: Kill off skeleton{64}.dtsi
Remove the usage of skeleton.dtsi in the remaining dts files. It was
deprecated since commit 9c0da3cc61 ("ARM: dts: explicitly mark
skeleton.dtsi as deprecated"). This will make adding a unit-address to
memory nodes easier.

The main tricky part to removing skeleton.dtsi is we could end up with
no /memory node at all when a bootloader depends on one being present. I
hacked up dtc to check for this condition.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2019-01-30 17:30:31 +01:00

68 lines
1.1 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
* Copyright (C) 2017 Luxul Inc.
*/
/dts-v1/;
#include "bcm4708.dtsi"
#include "bcm5301x-nand-cs0-bch8.dtsi"
/ {
compatible = "luxul,xbr-4500-v1", "brcm,bcm47094", "brcm,bcm4708";
model = "Luxul XBR-4500 V1";
chosen {
bootargs = "earlycon";
};
memory {
device_type = "memory";
reg = <0x00000000 0x08000000
0x88000000 0x18000000>;
};
leds {
compatible = "gpio-leds";
status {
label = "bcm53xx:green:status";
gpios = <&chipcommon 20 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "timer";
};
usb3 {
label = "bcm53xx:green:usb3";
gpios = <&chipcommon 19 GPIO_ACTIVE_HIGH>;
trigger-sources = <&ohci_port1>, <&ehci_port1>,
<&xhci_port1>;
linux,default-trigger = "usbport";
};
};
gpio-keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
restart {
label = "Reset";
linux,code = <KEY_RESTART>;
gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
};
};
};
&usb3 {
vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
};
&spi_nor {
status = "okay";
};
&usb3_phy {
status = "okay";
};