mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-29 22:14:41 +08:00
3a31f2d7fc
Use GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW instead of 0 and 1. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
289 lines
6.4 KiB
Plaintext
289 lines
6.4 KiB
Plaintext
/include/ "skeleton.dtsi"
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
|
|
|
|
/ {
|
|
compatible = "marvell,kirkwood";
|
|
interrupt-parent = <&intc>;
|
|
|
|
cpus {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
cpu@0 {
|
|
device_type = "cpu";
|
|
compatible = "marvell,feroceon";
|
|
reg = <0>;
|
|
clocks = <&core_clk 1>, <&core_clk 3>, <&gate_clk 11>;
|
|
clock-names = "cpu_clk", "ddrclk", "powersave";
|
|
};
|
|
};
|
|
|
|
aliases {
|
|
gpio0 = &gpio0;
|
|
gpio1 = &gpio1;
|
|
};
|
|
|
|
mbus {
|
|
compatible = "marvell,kirkwood-mbus", "simple-bus";
|
|
#address-cells = <2>;
|
|
#size-cells = <1>;
|
|
/* If a board file needs to change this ranges it must replace it completely */
|
|
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 /* internal-regs */
|
|
MBUS_ID(0x01, 0x2f) 0 0xf4000000 0x10000 /* nand flash */
|
|
MBUS_ID(0x03, 0x01) 0 0xf5000000 0x10000 /* crypto sram */
|
|
>;
|
|
controller = <&mbusc>;
|
|
pcie-mem-aperture = <0xe0000000 0x10000000>; /* 256 MiB memory space */
|
|
pcie-io-aperture = <0xf2000000 0x100000>; /* 1 MiB I/O space */
|
|
|
|
crypto@0301 {
|
|
compatible = "marvell,orion-crypto";
|
|
reg = <MBUS_ID(0xf0, 0x01) 0x30000 0x10000>,
|
|
<MBUS_ID(0x03, 0x01) 0 0x800>;
|
|
reg-names = "regs", "sram";
|
|
interrupts = <22>;
|
|
clocks = <&gate_clk 17>;
|
|
status = "okay";
|
|
};
|
|
|
|
nand: nand@012f {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
cle = <0>;
|
|
ale = <1>;
|
|
bank-width = <1>;
|
|
compatible = "marvell,orion-nand";
|
|
reg = <MBUS_ID(0x01, 0x2f) 0 0x400>;
|
|
chip-delay = <25>;
|
|
/* set partition map and/or chip-delay in board dts */
|
|
clocks = <&gate_clk 7>;
|
|
status = "disabled";
|
|
};
|
|
};
|
|
|
|
ocp@f1000000 {
|
|
compatible = "simple-bus";
|
|
ranges = <0x00000000 0xf1000000 0x0100000>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
mbusc: mbus-controller@20000 {
|
|
compatible = "marvell,mbus-controller";
|
|
reg = <0x20000 0x80>, <0x1500 0x20>;
|
|
};
|
|
|
|
timer: timer@20300 {
|
|
compatible = "marvell,orion-timer";
|
|
reg = <0x20300 0x20>;
|
|
interrupt-parent = <&bridge_intc>;
|
|
interrupts = <1>, <2>;
|
|
clocks = <&core_clk 0>;
|
|
};
|
|
|
|
intc: main-interrupt-ctrl@20200 {
|
|
compatible = "marvell,orion-intc";
|
|
interrupt-controller;
|
|
#interrupt-cells = <1>;
|
|
reg = <0x20200 0x10>, <0x20210 0x10>;
|
|
};
|
|
|
|
bridge_intc: bridge-interrupt-ctrl@20110 {
|
|
compatible = "marvell,orion-bridge-intc";
|
|
interrupt-controller;
|
|
#interrupt-cells = <1>;
|
|
reg = <0x20110 0x8>;
|
|
interrupts = <1>;
|
|
marvell,#interrupts = <6>;
|
|
};
|
|
|
|
core_clk: core-clocks@10030 {
|
|
compatible = "marvell,kirkwood-core-clock";
|
|
reg = <0x10030 0x4>;
|
|
#clock-cells = <1>;
|
|
};
|
|
|
|
gpio0: gpio@10100 {
|
|
compatible = "marvell,orion-gpio";
|
|
#gpio-cells = <2>;
|
|
gpio-controller;
|
|
reg = <0x10100 0x40>;
|
|
ngpios = <32>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
interrupts = <35>, <36>, <37>, <38>;
|
|
clocks = <&gate_clk 7>;
|
|
};
|
|
|
|
gpio1: gpio@10140 {
|
|
compatible = "marvell,orion-gpio";
|
|
#gpio-cells = <2>;
|
|
gpio-controller;
|
|
reg = <0x10140 0x40>;
|
|
ngpios = <18>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
interrupts = <39>, <40>, <41>;
|
|
clocks = <&gate_clk 7>;
|
|
};
|
|
|
|
serial@12000 {
|
|
compatible = "ns16550a";
|
|
reg = <0x12000 0x100>;
|
|
reg-shift = <2>;
|
|
interrupts = <33>;
|
|
clocks = <&gate_clk 7>;
|
|
status = "disabled";
|
|
};
|
|
|
|
serial@12100 {
|
|
compatible = "ns16550a";
|
|
reg = <0x12100 0x100>;
|
|
reg-shift = <2>;
|
|
interrupts = <34>;
|
|
clocks = <&gate_clk 7>;
|
|
status = "disabled";
|
|
};
|
|
|
|
spi@10600 {
|
|
compatible = "marvell,orion-spi";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
cell-index = <0>;
|
|
interrupts = <23>;
|
|
reg = <0x10600 0x28>;
|
|
clocks = <&gate_clk 7>;
|
|
status = "disabled";
|
|
};
|
|
|
|
gate_clk: clock-gating-control@2011c {
|
|
compatible = "marvell,kirkwood-gating-clock";
|
|
reg = <0x2011c 0x4>;
|
|
clocks = <&core_clk 0>;
|
|
#clock-cells = <1>;
|
|
};
|
|
|
|
wdt: watchdog-timer@20300 {
|
|
compatible = "marvell,orion-wdt";
|
|
reg = <0x20300 0x28>;
|
|
interrupt-parent = <&bridge_intc>;
|
|
interrupts = <3>;
|
|
clocks = <&gate_clk 7>;
|
|
status = "okay";
|
|
};
|
|
|
|
xor@60800 {
|
|
compatible = "marvell,orion-xor";
|
|
reg = <0x60800 0x100
|
|
0x60A00 0x100>;
|
|
status = "okay";
|
|
clocks = <&gate_clk 8>;
|
|
|
|
xor00 {
|
|
interrupts = <5>;
|
|
dmacap,memcpy;
|
|
dmacap,xor;
|
|
};
|
|
xor01 {
|
|
interrupts = <6>;
|
|
dmacap,memcpy;
|
|
dmacap,xor;
|
|
dmacap,memset;
|
|
};
|
|
};
|
|
|
|
xor@60900 {
|
|
compatible = "marvell,orion-xor";
|
|
reg = <0x60900 0x100
|
|
0x60B00 0x100>;
|
|
status = "okay";
|
|
clocks = <&gate_clk 16>;
|
|
|
|
xor00 {
|
|
interrupts = <7>;
|
|
dmacap,memcpy;
|
|
dmacap,xor;
|
|
};
|
|
xor01 {
|
|
interrupts = <8>;
|
|
dmacap,memcpy;
|
|
dmacap,xor;
|
|
dmacap,memset;
|
|
};
|
|
};
|
|
|
|
ehci@50000 {
|
|
compatible = "marvell,orion-ehci";
|
|
reg = <0x50000 0x1000>;
|
|
interrupts = <19>;
|
|
clocks = <&gate_clk 3>;
|
|
status = "okay";
|
|
};
|
|
|
|
i2c@11000 {
|
|
compatible = "marvell,mv64xxx-i2c";
|
|
reg = <0x11000 0x20>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
interrupts = <29>;
|
|
clock-frequency = <100000>;
|
|
clocks = <&gate_clk 7>;
|
|
status = "disabled";
|
|
};
|
|
|
|
mdio: mdio-bus@72004 {
|
|
compatible = "marvell,orion-mdio";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0x72004 0x84>;
|
|
interrupts = <46>;
|
|
clocks = <&gate_clk 0>;
|
|
status = "disabled";
|
|
|
|
/* add phy nodes in board file */
|
|
};
|
|
|
|
eth0: ethernet-controller@72000 {
|
|
compatible = "marvell,kirkwood-eth";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0x72000 0x4000>;
|
|
clocks = <&gate_clk 0>;
|
|
marvell,tx-checksum-limit = <1600>;
|
|
status = "disabled";
|
|
|
|
ethernet0-port@0 {
|
|
device_type = "network";
|
|
compatible = "marvell,kirkwood-eth-port";
|
|
reg = <0>;
|
|
interrupts = <11>;
|
|
/* overwrite MAC address in bootloader */
|
|
local-mac-address = [00 00 00 00 00 00];
|
|
/* set phy-handle property in board file */
|
|
};
|
|
};
|
|
|
|
eth1: ethernet-controller@76000 {
|
|
compatible = "marvell,kirkwood-eth";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0x76000 0x4000>;
|
|
clocks = <&gate_clk 19>;
|
|
marvell,tx-checksum-limit = <1600>;
|
|
status = "disabled";
|
|
|
|
ethernet1-port@0 {
|
|
device_type = "network";
|
|
compatible = "marvell,kirkwood-eth-port";
|
|
reg = <0>;
|
|
interrupts = <15>;
|
|
/* overwrite MAC address in bootloader */
|
|
local-mac-address = [00 00 00 00 00 00];
|
|
/* set phy-handle property in board file */
|
|
};
|
|
};
|
|
};
|
|
};
|