mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-26 12:34:41 +08:00
b7c6c17606
DT nodes should be named according to the type of object that they represent rather than the identity. DT nodes that contain a reg property should include a unit address in their name. Fix these issues. Add clock-output-names properties to the nodes so that the clocks get named something meaningful. This works around the fact that the fixed clock driver names clocks after the short node name, i.e. not including the unit address. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
183 lines
3.8 KiB
Plaintext
183 lines
3.8 KiB
Plaintext
/include/ "skeleton.dtsi"
|
|
|
|
/ {
|
|
compatible = "brcm,bcm2835";
|
|
model = "BCM2835";
|
|
interrupt-parent = <&intc>;
|
|
|
|
chosen {
|
|
bootargs = "earlyprintk console=ttyAMA0";
|
|
};
|
|
|
|
soc {
|
|
compatible = "simple-bus";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges = <0x7e000000 0x20000000 0x02000000>;
|
|
|
|
timer@7e003000 {
|
|
compatible = "brcm,bcm2835-system-timer";
|
|
reg = <0x7e003000 0x1000>;
|
|
interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
|
|
clock-frequency = <1000000>;
|
|
};
|
|
|
|
dma: dma@7e007000 {
|
|
compatible = "brcm,bcm2835-dma";
|
|
reg = <0x7e007000 0xf00>;
|
|
interrupts = <1 16>,
|
|
<1 17>,
|
|
<1 18>,
|
|
<1 19>,
|
|
<1 20>,
|
|
<1 21>,
|
|
<1 22>,
|
|
<1 23>,
|
|
<1 24>,
|
|
<1 25>,
|
|
<1 26>,
|
|
<1 27>,
|
|
<1 28>;
|
|
|
|
#dma-cells = <1>;
|
|
brcm,dma-channel-mask = <0x7f35>;
|
|
};
|
|
|
|
intc: interrupt-controller@7e00b200 {
|
|
compatible = "brcm,bcm2835-armctrl-ic";
|
|
reg = <0x7e00b200 0x200>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
watchdog@7e100000 {
|
|
compatible = "brcm,bcm2835-pm-wdt";
|
|
reg = <0x7e100000 0x28>;
|
|
};
|
|
|
|
rng@7e104000 {
|
|
compatible = "brcm,bcm2835-rng";
|
|
reg = <0x7e104000 0x10>;
|
|
};
|
|
|
|
gpio: gpio@7e200000 {
|
|
compatible = "brcm,bcm2835-gpio";
|
|
reg = <0x7e200000 0xb4>;
|
|
/*
|
|
* The GPIO IP block is designed for 3 banks of GPIOs.
|
|
* Each bank has a GPIO interrupt for itself.
|
|
* There is an overall "any bank" interrupt.
|
|
* In order, these are GIC interrupts 17, 18, 19, 20.
|
|
* Since the BCM2835 only has 2 banks, the 2nd bank
|
|
* interrupt output appears to be mirrored onto the
|
|
* 3rd bank's interrupt signal.
|
|
* So, a bank0 interrupt shows up on 17, 20, and
|
|
* a bank1 interrupt shows up on 18, 19, 20!
|
|
*/
|
|
interrupts = <2 17>, <2 18>, <2 19>, <2 20>;
|
|
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
uart@7e201000 {
|
|
compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell";
|
|
reg = <0x7e201000 0x1000>;
|
|
interrupts = <2 25>;
|
|
clock-frequency = <3000000>;
|
|
arm,primecell-periphid = <0x00241011>;
|
|
};
|
|
|
|
i2s: i2s@7e203000 {
|
|
compatible = "brcm,bcm2835-i2s";
|
|
reg = <0x7e203000 0x20>,
|
|
<0x7e101098 0x02>;
|
|
|
|
dmas = <&dma 2>,
|
|
<&dma 3>;
|
|
dma-names = "tx", "rx";
|
|
};
|
|
|
|
spi: spi@7e204000 {
|
|
compatible = "brcm,bcm2835-spi";
|
|
reg = <0x7e204000 0x1000>;
|
|
interrupts = <2 22>;
|
|
clocks = <&clk_spi>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "disabled";
|
|
};
|
|
|
|
i2c0: i2c@20205000 {
|
|
compatible = "brcm,bcm2835-i2c";
|
|
reg = <0x7e205000 0x1000>;
|
|
interrupts = <2 21>;
|
|
clocks = <&clk_i2c>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "disabled";
|
|
};
|
|
|
|
sdhci: sdhci@7e300000 {
|
|
compatible = "brcm,bcm2835-sdhci";
|
|
reg = <0x7e300000 0x100>;
|
|
interrupts = <2 30>;
|
|
clocks = <&clk_mmc>;
|
|
status = "disabled";
|
|
};
|
|
|
|
i2c1: i2c@7e804000 {
|
|
compatible = "brcm,bcm2835-i2c";
|
|
reg = <0x7e804000 0x1000>;
|
|
interrupts = <2 21>;
|
|
clocks = <&clk_i2c>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "disabled";
|
|
};
|
|
|
|
usb@7e980000 {
|
|
compatible = "brcm,bcm2835-usb";
|
|
reg = <0x7e980000 0x10000>;
|
|
interrupts = <1 9>;
|
|
};
|
|
|
|
arm-pmu {
|
|
compatible = "arm,arm1176-pmu";
|
|
};
|
|
};
|
|
|
|
clocks {
|
|
compatible = "simple-bus";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
clk_mmc: clock@0 {
|
|
compatible = "fixed-clock";
|
|
reg = <0>;
|
|
#clock-cells = <0>;
|
|
clock-output-names = "mmc";
|
|
clock-frequency = <100000000>;
|
|
};
|
|
|
|
clk_i2c: clock@1 {
|
|
compatible = "fixed-clock";
|
|
reg = <1>;
|
|
#clock-cells = <0>;
|
|
clock-output-names = "i2c";
|
|
clock-frequency = <250000000>;
|
|
};
|
|
|
|
clk_spi: clock@2 {
|
|
compatible = "fixed-clock";
|
|
reg = <2>;
|
|
#clock-cells = <0>;
|
|
clock-output-names = "spi";
|
|
clock-frequency = <250000000>;
|
|
};
|
|
};
|
|
};
|