mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-09-21 12:11:49 +08:00
3254ce8389
MD Danish Anwar says:
====================
Introduce HSR offload support for ICSSG
This series introduces HSR offload support for ICSSG driver. To support HSR
offload to hardware, ICSSG HSR firmware is used.
This series introduces,
1. HSR frame offload support for ICSSG driver.
2. HSR Tx Packet duplication offload
3. HSR Tx Tag and Rx Tag offload
4. Multicast filtering support in HSR offload mode.
5. Dependencies related to IEP.
HSR Test Setup:
--------------
___________ ___________ ___________
| | Link AB | | Link BC | |
__| AM64* |_________| AM64 |_________| AM64* |___
| | Station A | | Station B | | Station C | |
| |___________| |___________| |___________| |
| |
|______________________________________________________________|
Link CA
*Could be any device that supports two ethernet interfaces.
Steps to switch to HSR frame forward offload mode:
-------------------------------------------------
Example assuming eth1, eth2 ports of ICSSG1 on AM64-EVM
1) Enable HSR offload for both interfaces
ethtool -K eth1 hsr-fwd-offload on
ethtool -K eth1 hsr-dup-offload on
ethtool -K eth1 hsr-tag-ins-offload on
ethtool -K eth1 hsr-tag-rm-offload on
ethtool -K eth2 hsr-fwd-offload on
ethtool -K eth2 hsr-dup-offload on
ethtool -K eth2 hsr-tag-ins-offload on
ethtool -K eth2 hsr-tag-rm-offload on
2) Create HSR interface and add slave interfaces to it
ip link add name hsr0 type hsr slave1 eth1 slave2 eth2 \
supervision 45 version 1
3) Add IP address to the HSR interface
ip addr add <IP_ADDR>/24 dev hsr0
4) Bring up the HSR interface
ip link set hsr0 up
Switching back to previous mode:
--------------------------------
1) Delete HSR interface
ip link delete hsr0
2) Disable HSR port-to-port offloading mode, packet duplication
ethtool -K eth1 hsr-fwd-offload off
ethtool -K eth1 hsr-dup-offload off
ethtool -K eth1 hsr-tag-ins-offload off
ethtool -K eth1 hsr-tag-rm-offload off
ethtool -K eth2 hsr-fwd-offload off
ethtool -K eth2 hsr-dup-offload off
ethtool -K eth2 hsr-tag-ins-offload off
ethtool -K eth2 hsr-tag-rm-offload off
Testing the port-to-port frame forward offload feature:
-----------------------------------------------------
1) Connect the LAN cables as shown in the test setup.
2) Configure Station A and Station C in HSR non-offload mode.
3) Configure Station B is HSR offload mode.
4) Since HSR is a redundancy protocol, disconnect cable "Link CA",
to ensure frames from Station A reach Station C only through
Station B.
5) Run iperf3 Server on Station C and client on station A.
7) Check the CPU usage on Station B.
CPU usage report on Station B using mpstat when running UDP iperf3:
-------------------------------------------------------------------
1) Non-Offload case
-------------------
CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
all 0.00 0.00 0.50 0.00 3.52 29.15 0.00 0.00 66.83
0 0.00 0.00 0.00 0.00 7.00 58.00 0.00 0.00 35.00
1 0.00 0.00 0.99 0.00 0.99 0.00 0.00 0.00 98.02
2) Offload case
---------------
CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
all 0.00 0.00 0.00 0.00 0.50 0.00 0.00 0.00 99.50
0 0.00 0.00 0.99 0.00 0.00 0.00 0.00 0.00 99.01
1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00
Note:
1) At the very least, hsr-fwd-offload must be enabled.
Without offloading the port-to-port offload, other
HSR offloads cannot be enabled.
2) hsr-tag-ins-offload and hsr-dup-offload are tightly coupled in
the firmware implementation. They both need to be enabled / disabled
together.
v1: https://lore.kernel.org/20240808110800.1281716-1-danishanwar@ti.com/
v2: https://lore.kernel.org/20240813074233.2473876-1-danishanwar@ti.com
v3: https://lore.kernel.org/20240828091901.3120935-1-danishanwar@ti.com/
v4: https://lore.kernel.org/20240904100506.3665892-1-danishanwar@ti.com/
v5: https://lore.kernel.org/20240906111538.1259418-1-danishanwar@ti.com/
[0] https://lore.kernel.org/202409061658.vSwcFJiK-lkp@intel.com/
[1] https://lore.kernel.org/20240828091901.3120935-5-danishanwar@ti.com/
[2] https://lore.kernel.org/20240828091901.3120935-7-danishanwar@ti.com/
[3] https://lore.kernel.org/20240813074233.2473876-2-danishanwar@ti.com/
[4] https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=e846be0fba85
====================
Link: https://patch.msgid.link/20240911081603.2521729-1-danishanwar@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
||
|---|---|---|
| arch | ||
| block | ||
| certs | ||
| crypto | ||
| Documentation | ||
| drivers | ||
| fs | ||
| include | ||
| init | ||
| io_uring | ||
| ipc | ||
| kernel | ||
| lib | ||
| LICENSES | ||
| mm | ||
| net | ||
| rust | ||
| samples | ||
| scripts | ||
| security | ||
| sound | ||
| tools | ||
| usr | ||
| virt | ||
| .clang-format | ||
| .cocciconfig | ||
| .editorconfig | ||
| .get_maintainer.ignore | ||
| .gitattributes | ||
| .gitignore | ||
| .mailmap | ||
| .rustfmt.toml | ||
| COPYING | ||
| CREDITS | ||
| Kbuild | ||
| Kconfig | ||
| MAINTAINERS | ||
| Makefile | ||
| README | ||
Linux kernel
============
There are several guides for kernel developers and users. These guides can
be rendered in a number of formats, like HTML and PDF. Please read
Documentation/admin-guide/README.rst first.
In order to build the documentation, use ``make htmldocs`` or
``make pdfdocs``. The formatted documentation can also be read online at:
https://www.kernel.org/doc/html/latest/
There are various text files in the Documentation/ subdirectory,
several of them using the reStructuredText markup notation.
Please read the Documentation/process/changes.rst file, as it contains the
requirements for building and running the kernel, and information about
the problems which may result by upgrading your kernel.