mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-02 08:34:20 +08:00
7b1c56e08a
Tweak styling of names that come directly from the code. Suggested-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20221019093343.9546-6-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
136 lines
5.0 KiB
ReStructuredText
136 lines
5.0 KiB
ReStructuredText
===========================
|
|
RS485 Serial Communications
|
|
===========================
|
|
|
|
1. Introduction
|
|
===============
|
|
|
|
EIA-485, also known as TIA/EIA-485 or RS-485, is a standard defining the
|
|
electrical characteristics of drivers and receivers for use in balanced
|
|
digital multipoint systems.
|
|
This standard is widely used for communications in industrial automation
|
|
because it can be used effectively over long distances and in electrically
|
|
noisy environments.
|
|
|
|
2. Hardware-related Considerations
|
|
==================================
|
|
|
|
Some CPUs/UARTs (e.g., Atmel AT91 or 16C950 UART) contain a built-in
|
|
half-duplex mode capable of automatically controlling line direction by
|
|
toggling RTS or DTR signals. That can be used to control external
|
|
half-duplex hardware like an RS485 transceiver or any RS232-connected
|
|
half-duplex devices like some modems.
|
|
|
|
For these microcontrollers, the Linux driver should be made capable of
|
|
working in both modes, and proper ioctls (see later) should be made
|
|
available at user-level to allow switching from one mode to the other, and
|
|
vice versa.
|
|
|
|
3. Data Structures Already Available in the Kernel
|
|
==================================================
|
|
|
|
The Linux kernel provides the struct serial_rs485 to handle RS485
|
|
communications. This data structure is used to set and configure RS485
|
|
parameters in the platform data and in ioctls.
|
|
|
|
The device tree can also provide RS485 boot time parameters
|
|
[#DT-bindings]_. The serial core fills the struct serial_rs485 from the
|
|
values given by the device tree when the driver calls
|
|
uart_get_rs485_mode().
|
|
|
|
Any driver for devices capable of working both as RS232 and RS485 should
|
|
implement the ``rs485_config`` callback and provide ``rs485_supported``
|
|
in the ``struct uart_port``. The serial core calls ``rs485_config`` to do
|
|
the device specific part in response to TIOCSRS485 ioctl (see below). The
|
|
``rs485_config`` callback receives a pointer to a sanitizated struct
|
|
serial_rs485. The struct serial_rs485 userspace provides is sanitized
|
|
before calling ``rs485_config`` using ``rs485_supported`` that indicates
|
|
what RS485 features the driver supports for the ``struct uart_port``.
|
|
TIOCGRS485 ioctl can be used to read back the struct serial_rs485
|
|
matching to the current configuration.
|
|
|
|
.. kernel-doc:: include/uapi/linux/serial.h
|
|
:identifiers: serial_rs485 uart_get_rs485_mode
|
|
|
|
4. Usage from user-level
|
|
========================
|
|
|
|
From user-level, RS485 configuration can be get/set using the previous
|
|
ioctls. For instance, to set RS485 you can use the following code::
|
|
|
|
#include <linux/serial.h>
|
|
|
|
/* Include definition for RS485 ioctls: TIOCGRS485 and TIOCSRS485 */
|
|
#include <sys/ioctl.h>
|
|
|
|
/* Open your specific device (e.g., /dev/mydevice): */
|
|
int fd = open ("/dev/mydevice", O_RDWR);
|
|
if (fd < 0) {
|
|
/* Error handling. See errno. */
|
|
}
|
|
|
|
struct serial_rs485 rs485conf;
|
|
|
|
/* Enable RS485 mode: */
|
|
rs485conf.flags |= SER_RS485_ENABLED;
|
|
|
|
/* Set logical level for RTS pin equal to 1 when sending: */
|
|
rs485conf.flags |= SER_RS485_RTS_ON_SEND;
|
|
/* or, set logical level for RTS pin equal to 0 when sending: */
|
|
rs485conf.flags &= ~(SER_RS485_RTS_ON_SEND);
|
|
|
|
/* Set logical level for RTS pin equal to 1 after sending: */
|
|
rs485conf.flags |= SER_RS485_RTS_AFTER_SEND;
|
|
/* or, set logical level for RTS pin equal to 0 after sending: */
|
|
rs485conf.flags &= ~(SER_RS485_RTS_AFTER_SEND);
|
|
|
|
/* Set rts delay before send, if needed: */
|
|
rs485conf.delay_rts_before_send = ...;
|
|
|
|
/* Set rts delay after send, if needed: */
|
|
rs485conf.delay_rts_after_send = ...;
|
|
|
|
/* Set this flag if you want to receive data even while sending data */
|
|
rs485conf.flags |= SER_RS485_RX_DURING_TX;
|
|
|
|
if (ioctl (fd, TIOCSRS485, &rs485conf) < 0) {
|
|
/* Error handling. See errno. */
|
|
}
|
|
|
|
/* Use read() and write() syscalls here... */
|
|
|
|
/* Close the device when finished: */
|
|
if (close (fd) < 0) {
|
|
/* Error handling. See errno. */
|
|
}
|
|
|
|
5. Multipoint Addressing
|
|
========================
|
|
|
|
The Linux kernel provides addressing mode for multipoint RS-485 serial
|
|
communications line. The addressing mode is enabled with
|
|
``SER_RS485_ADDRB`` flag in struct serial_rs485. The struct serial_rs485
|
|
has two additional flags and fields for enabling receive and destination
|
|
addresses.
|
|
|
|
Address mode flags:
|
|
- ``SER_RS485_ADDRB``: Enabled addressing mode (sets also ADDRB in termios).
|
|
- ``SER_RS485_ADDR_RECV``: Receive (filter) address enabled.
|
|
- ``SER_RS485_ADDR_DEST``: Set destination address.
|
|
|
|
Address fields (enabled with corresponding ``SER_RS485_ADDR_*`` flag):
|
|
- ``addr_recv``: Receive address.
|
|
- ``addr_dest``: Destination address.
|
|
|
|
Once a receive address is set, the communication can occur only with the
|
|
particular device and other peers are filtered out. It is left up to the
|
|
receiver side to enforce the filtering. Receive address will be cleared
|
|
if ``SER_RS485_ADDR_RECV`` is not set.
|
|
|
|
Note: not all devices supporting RS485 support multipoint addressing.
|
|
|
|
6. References
|
|
=============
|
|
|
|
.. [#DT-bindings] Documentation/devicetree/bindings/serial/rs485.txt
|