mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-15 23:14:31 +08:00
ff43da86c6
MX6 and mx28 support enhanced DMA descriptor buff to support 1588 ptp. But MX25, MX3x, MX5x can't support enhanced DMA descriptor buff. Check fec type and choose correct DMA descriptor buff type. Remove static config CONFIG_FEC_PTP. ptp function will be auto detected. Signed-off-by: Frank Li <Frank.Li@freescale.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
97 lines
2.8 KiB
Plaintext
97 lines
2.8 KiB
Plaintext
#
|
|
# Freescale device configuration
|
|
#
|
|
|
|
config NET_VENDOR_FREESCALE
|
|
bool "Freescale devices"
|
|
default y
|
|
depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
|
|
M523x || M527x || M5272 || M528x || M520x || M532x || \
|
|
ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM)
|
|
---help---
|
|
If you have a network (Ethernet) card belonging to this class, say Y
|
|
and read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
Note that the answer to this question doesn't directly affect the
|
|
kernel: saying N will just cause the configurator to skip all
|
|
the questions about Freescale devices. If you say Y, you will be
|
|
asked for your specific card in the following questions.
|
|
|
|
if NET_VENDOR_FREESCALE
|
|
|
|
config FEC
|
|
tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
|
|
depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
|
|
ARCH_MXC || SOC_IMX28)
|
|
default ARCH_MXC || SOC_IMX28 if ARM
|
|
select PHYLIB
|
|
select PTP_1588_CLOCK
|
|
---help---
|
|
Say Y here if you want to use the built-in 10/100 Fast ethernet
|
|
controller on some Motorola ColdFire and Freescale i.MX processors.
|
|
|
|
config FEC_MPC52xx
|
|
tristate "FEC MPC52xx driver"
|
|
depends on PPC_MPC52xx && PPC_BESTCOMM
|
|
select CRC32
|
|
select PHYLIB
|
|
select PPC_BESTCOMM_FEC
|
|
---help---
|
|
This option enables support for the MPC5200's on-chip
|
|
Fast Ethernet Controller
|
|
If compiled as module, it will be called fec_mpc52xx.
|
|
|
|
config FEC_MPC52xx_MDIO
|
|
bool "FEC MPC52xx MDIO bus driver"
|
|
depends on FEC_MPC52xx
|
|
default y
|
|
---help---
|
|
The MPC5200's FEC can connect to the Ethernet either with
|
|
an external MII PHY chip or 10 Mbps 7-wire interface
|
|
(Motorola? industry standard).
|
|
If your board uses an external PHY connected to FEC, enable this.
|
|
If not sure, enable.
|
|
If compiled as module, it will be called fec_mpc52xx_phy.
|
|
|
|
source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
|
|
|
|
config FSL_PQ_MDIO
|
|
tristate "Freescale PQ MDIO"
|
|
depends on FSL_SOC
|
|
select PHYLIB
|
|
---help---
|
|
This driver supports the MDIO bus used by the gianfar and UCC drivers.
|
|
|
|
config FSL_XGMAC_MDIO
|
|
tristate "Freescale XGMAC MDIO"
|
|
depends on FSL_SOC
|
|
select PHYLIB
|
|
---help---
|
|
This driver supports the MDIO bus on the Fman 10G Ethernet MACs.
|
|
|
|
config UCC_GETH
|
|
tristate "Freescale QE Gigabit Ethernet"
|
|
depends on QUICC_ENGINE
|
|
select FSL_PQ_MDIO
|
|
select PHYLIB
|
|
---help---
|
|
This driver supports the Gigabit Ethernet mode of the QUICC Engine,
|
|
which is available on some Freescale SOCs.
|
|
|
|
config UGETH_TX_ON_DEMAND
|
|
bool "Transmit on Demand support"
|
|
depends on UCC_GETH
|
|
|
|
config GIANFAR
|
|
tristate "Gianfar Ethernet"
|
|
depends on FSL_SOC
|
|
select FSL_PQ_MDIO
|
|
select PHYLIB
|
|
select CRC32
|
|
---help---
|
|
This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
|
|
and MPC86xx family of chips, and the FEC on the 8540.
|
|
|
|
endif # NET_VENDOR_FREESCALE
|