mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-24 12:44:11 +08:00
e8a167b848
Use sg_miter iterator instead of sg_virt() and custom code to loop over the scatterlist. The memory iterator will do bounce buffering if the page happens to be located in high memory, which the driver may or may not be using. Suggested-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/linux-mmc/20240122073423.GA25859@lst.de/ Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20240127-mmc-proper-kmap-v2-8-d8e732aa97d1@linaro.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
523 lines
12 KiB
C
523 lines
12 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Freescale eSDHC ColdFire family controller driver, platform bus.
|
|
*
|
|
* Copyright (c) 2020 Timesys Corporation
|
|
* Author: Angelo Dureghello <angelo.dureghello@timesys.it>
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/platform_data/mmc-esdhc-mcf.h>
|
|
#include <linux/mmc/mmc.h>
|
|
#include "sdhci-pltfm.h"
|
|
#include "sdhci-esdhc.h"
|
|
|
|
#define ESDHC_PROCTL_D3CD 0x08
|
|
#define ESDHC_SYS_CTRL_DTOCV_MASK 0x0f
|
|
#define ESDHC_DEFAULT_HOST_CONTROL 0x28
|
|
|
|
/*
|
|
* Freescale eSDHC has DMA ERR flag at bit 28, not as std spec says, bit 25.
|
|
*/
|
|
#define ESDHC_INT_VENDOR_SPEC_DMA_ERR BIT(28)
|
|
|
|
struct pltfm_mcf_data {
|
|
struct clk *clk_ipg;
|
|
struct clk *clk_ahb;
|
|
struct clk *clk_per;
|
|
int aside;
|
|
int current_bus_width;
|
|
};
|
|
|
|
static inline void esdhc_mcf_buffer_swap32(u32 *buf, int len)
|
|
{
|
|
int i;
|
|
u32 temp;
|
|
|
|
len = (len + 3) >> 2;
|
|
|
|
for (i = 0; i < len; i++) {
|
|
temp = swab32(*buf);
|
|
*buf++ = temp;
|
|
}
|
|
}
|
|
|
|
static inline void esdhc_clrset_be(struct sdhci_host *host,
|
|
u32 mask, u32 val, int reg)
|
|
{
|
|
void __iomem *base = host->ioaddr + (reg & ~3);
|
|
u8 shift = (reg & 3) << 3;
|
|
|
|
mask <<= shift;
|
|
val <<= shift;
|
|
|
|
if (reg == SDHCI_HOST_CONTROL)
|
|
val |= ESDHC_PROCTL_D3CD;
|
|
|
|
writel((readl(base) & ~mask) | val, base);
|
|
}
|
|
|
|
/*
|
|
* Note: mcf is big-endian, single bytes need to be accessed at big endian
|
|
* offsets.
|
|
*/
|
|
static void esdhc_mcf_writeb_be(struct sdhci_host *host, u8 val, int reg)
|
|
{
|
|
void __iomem *base = host->ioaddr + (reg & ~3);
|
|
u8 shift = (reg & 3) << 3;
|
|
u32 mask = ~(0xff << shift);
|
|
|
|
if (reg == SDHCI_HOST_CONTROL) {
|
|
u32 host_ctrl = ESDHC_DEFAULT_HOST_CONTROL;
|
|
u8 dma_bits = (val & SDHCI_CTRL_DMA_MASK) >> 3;
|
|
u8 tmp = readb(host->ioaddr + SDHCI_HOST_CONTROL + 1);
|
|
|
|
tmp &= ~0x03;
|
|
tmp |= dma_bits;
|
|
|
|
/*
|
|
* Recomposition needed, restore always endianness and
|
|
* keep D3CD and AI, just setting bus width.
|
|
*/
|
|
host_ctrl |= val;
|
|
host_ctrl |= (dma_bits << 8);
|
|
writel(host_ctrl, host->ioaddr + SDHCI_HOST_CONTROL);
|
|
|
|
return;
|
|
}
|
|
|
|
writel((readl(base) & mask) | (val << shift), base);
|
|
}
|
|
|
|
static void esdhc_mcf_writew_be(struct sdhci_host *host, u16 val, int reg)
|
|
{
|
|
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
|
|
struct pltfm_mcf_data *mcf_data = sdhci_pltfm_priv(pltfm_host);
|
|
void __iomem *base = host->ioaddr + (reg & ~3);
|
|
u8 shift = (reg & 3) << 3;
|
|
u32 mask = ~(0xffff << shift);
|
|
|
|
switch (reg) {
|
|
case SDHCI_TRANSFER_MODE:
|
|
mcf_data->aside = val;
|
|
return;
|
|
case SDHCI_COMMAND:
|
|
if (host->cmd->opcode == MMC_STOP_TRANSMISSION)
|
|
val |= SDHCI_CMD_ABORTCMD;
|
|
|
|
/*
|
|
* As for the fsl driver,
|
|
* we have to set the mode in a single write here.
|
|
*/
|
|
writel(val << 16 | mcf_data->aside,
|
|
host->ioaddr + SDHCI_TRANSFER_MODE);
|
|
return;
|
|
}
|
|
|
|
writel((readl(base) & mask) | (val << shift), base);
|
|
}
|
|
|
|
static void esdhc_mcf_writel_be(struct sdhci_host *host, u32 val, int reg)
|
|
{
|
|
writel(val, host->ioaddr + reg);
|
|
}
|
|
|
|
static u8 esdhc_mcf_readb_be(struct sdhci_host *host, int reg)
|
|
{
|
|
if (reg == SDHCI_HOST_CONTROL) {
|
|
u8 __iomem *base = host->ioaddr + (reg & ~3);
|
|
u16 val = readw(base + 2);
|
|
u8 dma_bits = (val >> 5) & SDHCI_CTRL_DMA_MASK;
|
|
u8 host_ctrl = val & 0xff;
|
|
|
|
host_ctrl &= ~SDHCI_CTRL_DMA_MASK;
|
|
host_ctrl |= dma_bits;
|
|
|
|
return host_ctrl;
|
|
}
|
|
|
|
return readb(host->ioaddr + (reg ^ 0x3));
|
|
}
|
|
|
|
static u16 esdhc_mcf_readw_be(struct sdhci_host *host, int reg)
|
|
{
|
|
/*
|
|
* For SDHCI_HOST_VERSION, sdhci specs defines 0xFE,
|
|
* a wrong offset for us, we are at 0xFC.
|
|
*/
|
|
if (reg == SDHCI_HOST_VERSION)
|
|
reg -= 2;
|
|
|
|
return readw(host->ioaddr + (reg ^ 0x2));
|
|
}
|
|
|
|
static u32 esdhc_mcf_readl_be(struct sdhci_host *host, int reg)
|
|
{
|
|
u32 val;
|
|
|
|
val = readl(host->ioaddr + reg);
|
|
|
|
/*
|
|
* RM (25.3.9) sd pin clock must never exceed 25Mhz.
|
|
* So forcing legacy mode at 25Mhz.
|
|
*/
|
|
if (unlikely(reg == SDHCI_CAPABILITIES))
|
|
val &= ~SDHCI_CAN_DO_HISPD;
|
|
|
|
if (unlikely(reg == SDHCI_INT_STATUS)) {
|
|
if (val & ESDHC_INT_VENDOR_SPEC_DMA_ERR) {
|
|
val &= ~ESDHC_INT_VENDOR_SPEC_DMA_ERR;
|
|
val |= SDHCI_INT_ADMA_ERROR;
|
|
}
|
|
}
|
|
|
|
return val;
|
|
}
|
|
|
|
static unsigned int esdhc_mcf_get_max_timeout_count(struct sdhci_host *host)
|
|
{
|
|
return 1 << 27;
|
|
}
|
|
|
|
static void esdhc_mcf_set_timeout(struct sdhci_host *host,
|
|
struct mmc_command *cmd)
|
|
{
|
|
/* Use maximum timeout counter */
|
|
esdhc_clrset_be(host, ESDHC_SYS_CTRL_DTOCV_MASK, 0xE,
|
|
SDHCI_TIMEOUT_CONTROL);
|
|
}
|
|
|
|
static void esdhc_mcf_reset(struct sdhci_host *host, u8 mask)
|
|
{
|
|
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
|
|
struct pltfm_mcf_data *mcf_data = sdhci_pltfm_priv(pltfm_host);
|
|
|
|
sdhci_reset(host, mask);
|
|
|
|
esdhc_clrset_be(host, ESDHC_CTRL_BUSWIDTH_MASK,
|
|
mcf_data->current_bus_width, SDHCI_HOST_CONTROL);
|
|
|
|
sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
|
|
sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
|
|
}
|
|
|
|
static unsigned int esdhc_mcf_pltfm_get_max_clock(struct sdhci_host *host)
|
|
{
|
|
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
|
|
|
|
return pltfm_host->clock;
|
|
}
|
|
|
|
static unsigned int esdhc_mcf_pltfm_get_min_clock(struct sdhci_host *host)
|
|
{
|
|
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
|
|
|
|
return pltfm_host->clock / 256 / 16;
|
|
}
|
|
|
|
static void esdhc_mcf_pltfm_set_clock(struct sdhci_host *host,
|
|
unsigned int clock)
|
|
{
|
|
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
|
|
unsigned long *pll_dr = (unsigned long *)MCF_PLL_DR;
|
|
u32 fvco, fsys, fesdhc, temp;
|
|
const int sdclkfs[] = {2, 4, 8, 16, 32, 64, 128, 256};
|
|
int delta, old_delta = clock;
|
|
int i, q, ri, rq;
|
|
|
|
if (clock == 0) {
|
|
host->mmc->actual_clock = 0;
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* ColdFire eSDHC clock.s
|
|
*
|
|
* pll -+-> / outdiv1 --> fsys
|
|
* +-> / outdiv3 --> eSDHC clock ---> / SDCCLKFS / DVS
|
|
*
|
|
* mcf5441x datasheet says:
|
|
* (8.1.2) eSDHC should be 40 MHz max
|
|
* (25.3.9) eSDHC input is, as example, 96 Mhz ...
|
|
* (25.3.9) sd pin clock must never exceed 25Mhz
|
|
*
|
|
* fvco = fsys * outdvi1 + 1
|
|
* fshdc = fvco / outdiv3 + 1
|
|
*/
|
|
temp = readl(pll_dr);
|
|
fsys = pltfm_host->clock;
|
|
fvco = fsys * ((temp & 0x1f) + 1);
|
|
fesdhc = fvco / (((temp >> 10) & 0x1f) + 1);
|
|
|
|
for (i = 0; i < 8; ++i) {
|
|
int result = fesdhc / sdclkfs[i];
|
|
|
|
for (q = 1; q < 17; ++q) {
|
|
int finale = result / q;
|
|
|
|
delta = abs(clock - finale);
|
|
|
|
if (delta < old_delta) {
|
|
old_delta = delta;
|
|
ri = i;
|
|
rq = q;
|
|
}
|
|
}
|
|
}
|
|
|
|
/*
|
|
* Apply divisors and re-enable all the clocks
|
|
*/
|
|
temp = ((sdclkfs[ri] >> 1) << 8) | ((rq - 1) << 4) |
|
|
(ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN);
|
|
esdhc_clrset_be(host, 0x0000fff7, temp, SDHCI_CLOCK_CONTROL);
|
|
|
|
host->mmc->actual_clock = clock;
|
|
|
|
mdelay(1);
|
|
}
|
|
|
|
static void esdhc_mcf_pltfm_set_bus_width(struct sdhci_host *host, int width)
|
|
{
|
|
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
|
|
struct pltfm_mcf_data *mcf_data = sdhci_pltfm_priv(pltfm_host);
|
|
|
|
switch (width) {
|
|
case MMC_BUS_WIDTH_4:
|
|
mcf_data->current_bus_width = ESDHC_CTRL_4BITBUS;
|
|
break;
|
|
default:
|
|
mcf_data->current_bus_width = 0;
|
|
break;
|
|
}
|
|
|
|
esdhc_clrset_be(host, ESDHC_CTRL_BUSWIDTH_MASK,
|
|
mcf_data->current_bus_width, SDHCI_HOST_CONTROL);
|
|
}
|
|
|
|
static void esdhc_mcf_request_done(struct sdhci_host *host,
|
|
struct mmc_request *mrq)
|
|
{
|
|
struct sg_mapping_iter sgm;
|
|
u32 *buffer;
|
|
|
|
if (!mrq->data || !mrq->data->bytes_xfered)
|
|
goto exit_done;
|
|
|
|
if (mmc_get_dma_dir(mrq->data) != DMA_FROM_DEVICE)
|
|
goto exit_done;
|
|
|
|
/*
|
|
* On mcf5441x there is no hw sdma option/flag to select the dma
|
|
* transfer endiannes. A swap after the transfer is needed.
|
|
*/
|
|
sg_miter_start(&sgm, mrq->data->sg, mrq->data->sg_len,
|
|
SG_MITER_TO_SG | SG_MITER_FROM_SG);
|
|
while (sg_miter_next(&sgm)) {
|
|
buffer = sgm.addr;
|
|
esdhc_mcf_buffer_swap32(buffer, sgm.length);
|
|
}
|
|
sg_miter_stop(&sgm);
|
|
|
|
exit_done:
|
|
mmc_request_done(host->mmc, mrq);
|
|
}
|
|
|
|
static void esdhc_mcf_copy_to_bounce_buffer(struct sdhci_host *host,
|
|
struct mmc_data *data,
|
|
unsigned int length)
|
|
{
|
|
sg_copy_to_buffer(data->sg, data->sg_len,
|
|
host->bounce_buffer, length);
|
|
|
|
esdhc_mcf_buffer_swap32((u32 *)host->bounce_buffer,
|
|
data->blksz * data->blocks);
|
|
}
|
|
|
|
static struct sdhci_ops sdhci_esdhc_ops = {
|
|
.reset = esdhc_mcf_reset,
|
|
.set_clock = esdhc_mcf_pltfm_set_clock,
|
|
.get_max_clock = esdhc_mcf_pltfm_get_max_clock,
|
|
.get_min_clock = esdhc_mcf_pltfm_get_min_clock,
|
|
.set_bus_width = esdhc_mcf_pltfm_set_bus_width,
|
|
.get_max_timeout_count = esdhc_mcf_get_max_timeout_count,
|
|
.set_timeout = esdhc_mcf_set_timeout,
|
|
.write_b = esdhc_mcf_writeb_be,
|
|
.write_w = esdhc_mcf_writew_be,
|
|
.write_l = esdhc_mcf_writel_be,
|
|
.read_b = esdhc_mcf_readb_be,
|
|
.read_w = esdhc_mcf_readw_be,
|
|
.read_l = esdhc_mcf_readl_be,
|
|
.copy_to_bounce_buffer = esdhc_mcf_copy_to_bounce_buffer,
|
|
.request_done = esdhc_mcf_request_done,
|
|
};
|
|
|
|
static const struct sdhci_pltfm_data sdhci_esdhc_mcf_pdata = {
|
|
.ops = &sdhci_esdhc_ops,
|
|
.quirks = ESDHC_DEFAULT_QUIRKS | SDHCI_QUIRK_FORCE_DMA,
|
|
/*
|
|
* Mandatory quirk,
|
|
* controller does not support cmd23,
|
|
* without, on > 8G cards cmd23 is used, and
|
|
* driver times out.
|
|
*/
|
|
SDHCI_QUIRK2_HOST_NO_CMD23,
|
|
};
|
|
|
|
static int esdhc_mcf_plat_init(struct sdhci_host *host,
|
|
struct pltfm_mcf_data *mcf_data)
|
|
{
|
|
struct mcf_esdhc_platform_data *plat_data;
|
|
struct device *dev = mmc_dev(host->mmc);
|
|
|
|
if (!dev->platform_data) {
|
|
dev_err(dev, "no platform data!\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
plat_data = (struct mcf_esdhc_platform_data *)dev->platform_data;
|
|
|
|
/* Card_detect */
|
|
switch (plat_data->cd_type) {
|
|
default:
|
|
case ESDHC_CD_CONTROLLER:
|
|
/* We have a working card_detect back */
|
|
host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION;
|
|
break;
|
|
case ESDHC_CD_PERMANENT:
|
|
host->mmc->caps |= MMC_CAP_NONREMOVABLE;
|
|
break;
|
|
case ESDHC_CD_NONE:
|
|
break;
|
|
}
|
|
|
|
switch (plat_data->max_bus_width) {
|
|
case 4:
|
|
host->mmc->caps |= MMC_CAP_4_BIT_DATA;
|
|
break;
|
|
case 1:
|
|
default:
|
|
host->quirks |= SDHCI_QUIRK_FORCE_1_BIT_DATA;
|
|
break;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int sdhci_esdhc_mcf_probe(struct platform_device *pdev)
|
|
{
|
|
struct sdhci_host *host;
|
|
struct sdhci_pltfm_host *pltfm_host;
|
|
struct pltfm_mcf_data *mcf_data;
|
|
int err;
|
|
|
|
host = sdhci_pltfm_init(pdev, &sdhci_esdhc_mcf_pdata,
|
|
sizeof(*mcf_data));
|
|
|
|
if (IS_ERR(host))
|
|
return PTR_ERR(host);
|
|
|
|
pltfm_host = sdhci_priv(host);
|
|
mcf_data = sdhci_pltfm_priv(pltfm_host);
|
|
|
|
host->sdma_boundary = 0;
|
|
|
|
host->flags |= SDHCI_AUTO_CMD12;
|
|
|
|
mcf_data->clk_ipg = devm_clk_get(&pdev->dev, "ipg");
|
|
if (IS_ERR(mcf_data->clk_ipg)) {
|
|
err = PTR_ERR(mcf_data->clk_ipg);
|
|
goto err_exit;
|
|
}
|
|
|
|
mcf_data->clk_ahb = devm_clk_get(&pdev->dev, "ahb");
|
|
if (IS_ERR(mcf_data->clk_ahb)) {
|
|
err = PTR_ERR(mcf_data->clk_ahb);
|
|
goto err_exit;
|
|
}
|
|
|
|
mcf_data->clk_per = devm_clk_get(&pdev->dev, "per");
|
|
if (IS_ERR(mcf_data->clk_per)) {
|
|
err = PTR_ERR(mcf_data->clk_per);
|
|
goto err_exit;
|
|
}
|
|
|
|
pltfm_host->clk = mcf_data->clk_per;
|
|
pltfm_host->clock = clk_get_rate(pltfm_host->clk);
|
|
err = clk_prepare_enable(mcf_data->clk_per);
|
|
if (err)
|
|
goto err_exit;
|
|
|
|
err = clk_prepare_enable(mcf_data->clk_ipg);
|
|
if (err)
|
|
goto unprep_per;
|
|
|
|
err = clk_prepare_enable(mcf_data->clk_ahb);
|
|
if (err)
|
|
goto unprep_ipg;
|
|
|
|
err = esdhc_mcf_plat_init(host, mcf_data);
|
|
if (err)
|
|
goto unprep_ahb;
|
|
|
|
err = sdhci_setup_host(host);
|
|
if (err)
|
|
goto unprep_ahb;
|
|
|
|
if (!host->bounce_buffer) {
|
|
dev_err(&pdev->dev, "bounce buffer not allocated");
|
|
err = -ENOMEM;
|
|
goto cleanup;
|
|
}
|
|
|
|
err = __sdhci_add_host(host);
|
|
if (err)
|
|
goto cleanup;
|
|
|
|
return 0;
|
|
|
|
cleanup:
|
|
sdhci_cleanup_host(host);
|
|
unprep_ahb:
|
|
clk_disable_unprepare(mcf_data->clk_ahb);
|
|
unprep_ipg:
|
|
clk_disable_unprepare(mcf_data->clk_ipg);
|
|
unprep_per:
|
|
clk_disable_unprepare(mcf_data->clk_per);
|
|
err_exit:
|
|
sdhci_pltfm_free(pdev);
|
|
|
|
return err;
|
|
}
|
|
|
|
static void sdhci_esdhc_mcf_remove(struct platform_device *pdev)
|
|
{
|
|
struct sdhci_host *host = platform_get_drvdata(pdev);
|
|
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
|
|
struct pltfm_mcf_data *mcf_data = sdhci_pltfm_priv(pltfm_host);
|
|
|
|
sdhci_remove_host(host, 0);
|
|
|
|
clk_disable_unprepare(mcf_data->clk_ipg);
|
|
clk_disable_unprepare(mcf_data->clk_ahb);
|
|
clk_disable_unprepare(mcf_data->clk_per);
|
|
|
|
sdhci_pltfm_free(pdev);
|
|
}
|
|
|
|
static struct platform_driver sdhci_esdhc_mcf_driver = {
|
|
.driver = {
|
|
.name = "sdhci-esdhc-mcf",
|
|
.probe_type = PROBE_PREFER_ASYNCHRONOUS,
|
|
},
|
|
.probe = sdhci_esdhc_mcf_probe,
|
|
.remove_new = sdhci_esdhc_mcf_remove,
|
|
};
|
|
|
|
module_platform_driver(sdhci_esdhc_mcf_driver);
|
|
|
|
MODULE_DESCRIPTION("SDHCI driver for Freescale ColdFire eSDHC");
|
|
MODULE_AUTHOR("Angelo Dureghello <angelo.dureghello@timesys.com>");
|
|
MODULE_LICENSE("GPL v2");
|