linux/drivers/mfd/intel_soc_pmic_chtwc.c
Hans de Goede 3afcbe0947 mfd: intel_soc_pmic_chtwc: Add cht_wc_model data to struct intel_soc_pmic
Tablet / laptop designs using an Intel Cherry Trail x86 main SoC with
an Intel Whiskey Cove PMIC do not use a single standard setup for
the charger, fuel-gauge and other chips surrounding the PMIC /
charging+data USB port.

Unlike what is normal on x86 this diversity in designs is not handled
by the ACPI tables. On 2 of the 3 known designs there are no standard
(PNP0C0A) ACPI battery devices and on the 3th design the ACPI battery
device does not work under Linux due to it requiring non-standard
and undocumented ACPI behavior.

So to make things work under Linux we use native charger and fuel-gauge
drivers on these devices, re-using the native drivers used on ARM boards
with the same charger / fuel-gauge ICs.

This requires various MFD-cell drivers for the CHT-WC PMIC cells to
know which model they are exactly running on so that they can e.g.
instantiate an I2C-client for the right model charger-IC (the charger
is connected to an I2C-controller which is part of the PMIC).

Rather then duplicating DMI-id matching to check which model we are
running on in each MFD-cell driver, add a check for this to the
shared drivers/mfd/intel_soc_pmic_chtwc.c code by using a
DMI table for all 3 known models:

1. The GPD Win and GPD Pocket mini-laptops, these are really 2 models
but the Pocket re-uses the GPD Win's design in a different housing:

The WC PMIC is connected to a TI BQ24292i charger, paired with
a Maxim MAX17047 fuelgauge + a FUSB302 USB Type-C Controller +
a PI3USB30532 USB switch, for a fully functional Type-C port.

2. The Xiaomi Mi Pad 2:

The WC PMIC is connected to a TI BQ25890 charger, paired with
a TI BQ27520 fuelgauge, using the TI BQ25890 for BC1.2 charger type
detection, for a USB-2 only Type-C port without PD.

3. The Lenovo Yoga Book YB1-X90 / Lenovo Yoga Book YB1-X91 series:

The WC PMIC is connected to a TI BQ25892 charger, paired with
a TI BQ27542 fuelgauge, using the WC PMIC for BC1.2 charger type
detection and using the BQ25892's Mediatek Pump Express+ (1.0)
support to enable charging with up to 12V through a micro-USB port.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2022-02-01 14:55:12 +01:00

269 lines
7.0 KiB
C

// SPDX-License-Identifier: GPL-2.0
/*
* MFD core driver for Intel Cherrytrail Whiskey Cove PMIC
*
* Copyright (C) 2017 Hans de Goede <hdegoede@redhat.com>
*
* Based on various non upstream patches to support the CHT Whiskey Cove PMIC:
* Copyright (C) 2013-2015 Intel Corporation. All rights reserved.
*/
#include <linux/acpi.h>
#include <linux/delay.h>
#include <linux/dmi.h>
#include <linux/err.h>
#include <linux/i2c.h>
#include <linux/interrupt.h>
#include <linux/kernel.h>
#include <linux/mfd/core.h>
#include <linux/mfd/intel_soc_pmic.h>
#include <linux/regmap.h>
/* PMIC device registers */
#define REG_OFFSET_MASK GENMASK(7, 0)
#define REG_ADDR_MASK GENMASK(15, 8)
#define REG_ADDR_SHIFT 8
#define CHT_WC_IRQLVL1 0x6e02
#define CHT_WC_IRQLVL1_MASK 0x6e0e
/* Whiskey Cove PMIC share same ACPI ID between different platforms */
#define CHT_WC_HRV 3
/* Level 1 IRQs (level 2 IRQs are handled in the child device drivers) */
enum {
CHT_WC_PWRSRC_IRQ = 0,
CHT_WC_THRM_IRQ,
CHT_WC_BCU_IRQ,
CHT_WC_ADC_IRQ,
CHT_WC_EXT_CHGR_IRQ,
CHT_WC_GPIO_IRQ,
/* There is no irq 6 */
CHT_WC_CRIT_IRQ = 7,
};
static const struct resource cht_wc_pwrsrc_resources[] = {
DEFINE_RES_IRQ(CHT_WC_PWRSRC_IRQ),
};
static const struct resource cht_wc_ext_charger_resources[] = {
DEFINE_RES_IRQ(CHT_WC_EXT_CHGR_IRQ),
};
static struct mfd_cell cht_wc_dev[] = {
{
.name = "cht_wcove_pwrsrc",
.num_resources = ARRAY_SIZE(cht_wc_pwrsrc_resources),
.resources = cht_wc_pwrsrc_resources,
}, {
.name = "cht_wcove_ext_chgr",
.num_resources = ARRAY_SIZE(cht_wc_ext_charger_resources),
.resources = cht_wc_ext_charger_resources,
},
{ .name = "cht_wcove_region", },
{ .name = "cht_wcove_leds", },
};
/*
* The CHT Whiskey Cove covers multiple I2C addresses, with a 1 Byte
* register address space per I2C address, so we use 16 bit register
* addresses where the high 8 bits contain the I2C client address.
*/
static int cht_wc_byte_reg_read(void *context, unsigned int reg,
unsigned int *val)
{
struct i2c_client *client = context;
int ret, orig_addr = client->addr;
if (!(reg & REG_ADDR_MASK)) {
dev_err(&client->dev, "Error I2C address not specified\n");
return -EINVAL;
}
client->addr = (reg & REG_ADDR_MASK) >> REG_ADDR_SHIFT;
ret = i2c_smbus_read_byte_data(client, reg & REG_OFFSET_MASK);
client->addr = orig_addr;
if (ret < 0)
return ret;
*val = ret;
return 0;
}
static int cht_wc_byte_reg_write(void *context, unsigned int reg,
unsigned int val)
{
struct i2c_client *client = context;
int ret, orig_addr = client->addr;
if (!(reg & REG_ADDR_MASK)) {
dev_err(&client->dev, "Error I2C address not specified\n");
return -EINVAL;
}
client->addr = (reg & REG_ADDR_MASK) >> REG_ADDR_SHIFT;
ret = i2c_smbus_write_byte_data(client, reg & REG_OFFSET_MASK, val);
client->addr = orig_addr;
return ret;
}
static const struct regmap_config cht_wc_regmap_cfg = {
.reg_bits = 16,
.val_bits = 8,
.reg_write = cht_wc_byte_reg_write,
.reg_read = cht_wc_byte_reg_read,
};
static const struct regmap_irq cht_wc_regmap_irqs[] = {
REGMAP_IRQ_REG(CHT_WC_PWRSRC_IRQ, 0, BIT(CHT_WC_PWRSRC_IRQ)),
REGMAP_IRQ_REG(CHT_WC_THRM_IRQ, 0, BIT(CHT_WC_THRM_IRQ)),
REGMAP_IRQ_REG(CHT_WC_BCU_IRQ, 0, BIT(CHT_WC_BCU_IRQ)),
REGMAP_IRQ_REG(CHT_WC_ADC_IRQ, 0, BIT(CHT_WC_ADC_IRQ)),
REGMAP_IRQ_REG(CHT_WC_EXT_CHGR_IRQ, 0, BIT(CHT_WC_EXT_CHGR_IRQ)),
REGMAP_IRQ_REG(CHT_WC_GPIO_IRQ, 0, BIT(CHT_WC_GPIO_IRQ)),
REGMAP_IRQ_REG(CHT_WC_CRIT_IRQ, 0, BIT(CHT_WC_CRIT_IRQ)),
};
static const struct regmap_irq_chip cht_wc_regmap_irq_chip = {
.name = "cht_wc_irq_chip",
.status_base = CHT_WC_IRQLVL1,
.mask_base = CHT_WC_IRQLVL1_MASK,
.irqs = cht_wc_regmap_irqs,
.num_irqs = ARRAY_SIZE(cht_wc_regmap_irqs),
.num_regs = 1,
};
static const struct dmi_system_id cht_wc_model_dmi_ids[] = {
{
/* GPD win / GPD pocket mini laptops */
.driver_data = (void *)(long)INTEL_CHT_WC_GPD_WIN_POCKET,
/*
* This DMI match may not seem unique, but it is. In the 67000+
* DMI decode dumps from linux-hardware.org only 116 have
* board_vendor set to "AMI Corporation" and of those 116 only
* the GPD win's and pocket's board_name is "Default string".
*/
.matches = {
DMI_EXACT_MATCH(DMI_BOARD_VENDOR, "AMI Corporation"),
DMI_EXACT_MATCH(DMI_BOARD_NAME, "Default string"),
DMI_EXACT_MATCH(DMI_BOARD_SERIAL, "Default string"),
DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "Default string"),
},
}, {
/* Xiaomi Mi Pad 2 */
.driver_data = (void *)(long)INTEL_CHT_WC_XIAOMI_MIPAD2,
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "Xiaomi Inc"),
DMI_MATCH(DMI_PRODUCT_NAME, "Mipad2"),
},
}, {
/* Lenovo Yoga Book X90F / X91F / X91L */
.driver_data = (void *)(long)INTEL_CHT_WC_LENOVO_YOGABOOK1,
.matches = {
/* Non exact match to match all versions */
DMI_MATCH(DMI_PRODUCT_NAME, "Lenovo YB1-X9"),
},
},
{ }
};
static int cht_wc_probe(struct i2c_client *client)
{
struct device *dev = &client->dev;
const struct dmi_system_id *id;
struct intel_soc_pmic *pmic;
acpi_status status;
unsigned long long hrv;
int ret;
status = acpi_evaluate_integer(ACPI_HANDLE(dev), "_HRV", NULL, &hrv);
if (ACPI_FAILURE(status)) {
dev_err(dev, "Failed to get PMIC hardware revision\n");
return -ENODEV;
}
if (hrv != CHT_WC_HRV) {
dev_err(dev, "Invalid PMIC hardware revision: %llu\n", hrv);
return -ENODEV;
}
if (client->irq < 0) {
dev_err(dev, "Invalid IRQ\n");
return -EINVAL;
}
pmic = devm_kzalloc(dev, sizeof(*pmic), GFP_KERNEL);
if (!pmic)
return -ENOMEM;
id = dmi_first_match(cht_wc_model_dmi_ids);
if (id)
pmic->cht_wc_model = (long)id->driver_data;
pmic->irq = client->irq;
pmic->dev = dev;
i2c_set_clientdata(client, pmic);
pmic->regmap = devm_regmap_init(dev, NULL, client, &cht_wc_regmap_cfg);
if (IS_ERR(pmic->regmap))
return PTR_ERR(pmic->regmap);
ret = devm_regmap_add_irq_chip(dev, pmic->regmap, pmic->irq,
IRQF_ONESHOT | IRQF_SHARED, 0,
&cht_wc_regmap_irq_chip,
&pmic->irq_chip_data);
if (ret)
return ret;
return devm_mfd_add_devices(dev, PLATFORM_DEVID_NONE,
cht_wc_dev, ARRAY_SIZE(cht_wc_dev), NULL, 0,
regmap_irq_get_domain(pmic->irq_chip_data));
}
static void cht_wc_shutdown(struct i2c_client *client)
{
struct intel_soc_pmic *pmic = i2c_get_clientdata(client);
disable_irq(pmic->irq);
}
static int __maybe_unused cht_wc_suspend(struct device *dev)
{
struct intel_soc_pmic *pmic = dev_get_drvdata(dev);
disable_irq(pmic->irq);
return 0;
}
static int __maybe_unused cht_wc_resume(struct device *dev)
{
struct intel_soc_pmic *pmic = dev_get_drvdata(dev);
enable_irq(pmic->irq);
return 0;
}
static SIMPLE_DEV_PM_OPS(cht_wc_pm_ops, cht_wc_suspend, cht_wc_resume);
static const struct i2c_device_id cht_wc_i2c_id[] = {
{ }
};
static const struct acpi_device_id cht_wc_acpi_ids[] = {
{ "INT34D3", },
{ }
};
static struct i2c_driver cht_wc_driver = {
.driver = {
.name = "CHT Whiskey Cove PMIC",
.pm = &cht_wc_pm_ops,
.acpi_match_table = cht_wc_acpi_ids,
},
.probe_new = cht_wc_probe,
.shutdown = cht_wc_shutdown,
.id_table = cht_wc_i2c_id,
};
builtin_i2c_driver(cht_wc_driver);