mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-14 22:44:27 +08:00
9e0bf8393d
The MAX9271 chip manual prescribes a delay of 5 milliseconds after the chip exits from low power state. Add a new function to the max9271 library driver that wakes up the chip with a dummy i2c transaction and implements the correct delay of 5 milliseconds after the chip exits from low power state. Use the newly introduced function in the rdacm20 and rdacm21 camera drivers. The former was not respecting the required delay while the latter was waiting for a too-short timeout. Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
234 lines
7.5 KiB
C
234 lines
7.5 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright (C) 2017-2020 Jacopo Mondi
|
|
* Copyright (C) 2017-2020 Kieran Bingham
|
|
* Copyright (C) 2017-2020 Laurent Pinchart
|
|
* Copyright (C) 2017-2020 Niklas Söderlund
|
|
* Copyright (C) 2016 Renesas Electronics Corporation
|
|
* Copyright (C) 2015 Cogent Embedded, Inc.
|
|
*/
|
|
|
|
#include <linux/i2c.h>
|
|
|
|
#define MAX9271_DEFAULT_ADDR 0x40
|
|
|
|
/* Register 0x02 */
|
|
#define MAX9271_SPREAD_SPECT_0 (0 << 5)
|
|
#define MAX9271_SPREAD_SPECT_05 (1 << 5)
|
|
#define MAX9271_SPREAD_SPECT_15 (2 << 5)
|
|
#define MAX9271_SPREAD_SPECT_1 (5 << 5)
|
|
#define MAX9271_SPREAD_SPECT_2 (3 << 5)
|
|
#define MAX9271_SPREAD_SPECT_3 (6 << 5)
|
|
#define MAX9271_SPREAD_SPECT_4 (7 << 5)
|
|
#define MAX9271_R02_RES BIT(4)
|
|
#define MAX9271_PCLK_AUTODETECT (3 << 2)
|
|
#define MAX9271_SERIAL_AUTODETECT (0x03)
|
|
/* Register 0x04 */
|
|
#define MAX9271_SEREN BIT(7)
|
|
#define MAX9271_CLINKEN BIT(6)
|
|
#define MAX9271_PRBSEN BIT(5)
|
|
#define MAX9271_SLEEP BIT(4)
|
|
#define MAX9271_INTTYPE_I2C (0 << 2)
|
|
#define MAX9271_INTTYPE_UART (1 << 2)
|
|
#define MAX9271_INTTYPE_NONE (2 << 2)
|
|
#define MAX9271_REVCCEN BIT(1)
|
|
#define MAX9271_FWDCCEN BIT(0)
|
|
/* Register 0x07 */
|
|
#define MAX9271_DBL BIT(7)
|
|
#define MAX9271_DRS BIT(6)
|
|
#define MAX9271_BWS BIT(5)
|
|
#define MAX9271_ES BIT(4)
|
|
#define MAX9271_HVEN BIT(2)
|
|
#define MAX9271_EDC_1BIT_PARITY (0 << 0)
|
|
#define MAX9271_EDC_6BIT_CRC (1 << 0)
|
|
#define MAX9271_EDC_6BIT_HAMMING (2 << 0)
|
|
/* Register 0x08 */
|
|
#define MAX9271_INVVS BIT(7)
|
|
#define MAX9271_INVHS BIT(6)
|
|
#define MAX9271_REV_LOGAIN BIT(3)
|
|
#define MAX9271_REV_HIVTH BIT(0)
|
|
/* Register 0x09 */
|
|
#define MAX9271_ID 0x09
|
|
/* Register 0x0d */
|
|
#define MAX9271_I2CLOCACK BIT(7)
|
|
#define MAX9271_I2CSLVSH_1046NS_469NS (3 << 5)
|
|
#define MAX9271_I2CSLVSH_938NS_352NS (2 << 5)
|
|
#define MAX9271_I2CSLVSH_469NS_234NS (1 << 5)
|
|
#define MAX9271_I2CSLVSH_352NS_117NS (0 << 5)
|
|
#define MAX9271_I2CMSTBT_837KBPS (7 << 2)
|
|
#define MAX9271_I2CMSTBT_533KBPS (6 << 2)
|
|
#define MAX9271_I2CMSTBT_339KBPS (5 << 2)
|
|
#define MAX9271_I2CMSTBT_173KBPS (4 << 2)
|
|
#define MAX9271_I2CMSTBT_105KBPS (3 << 2)
|
|
#define MAX9271_I2CMSTBT_84KBPS (2 << 2)
|
|
#define MAX9271_I2CMSTBT_28KBPS (1 << 2)
|
|
#define MAX9271_I2CMSTBT_8KBPS (0 << 2)
|
|
#define MAX9271_I2CSLVTO_NONE (3 << 0)
|
|
#define MAX9271_I2CSLVTO_1024US (2 << 0)
|
|
#define MAX9271_I2CSLVTO_256US (1 << 0)
|
|
#define MAX9271_I2CSLVTO_64US (0 << 0)
|
|
/* Register 0x0f */
|
|
#define MAX9271_GPIO5OUT BIT(5)
|
|
#define MAX9271_GPIO4OUT BIT(4)
|
|
#define MAX9271_GPIO3OUT BIT(3)
|
|
#define MAX9271_GPIO2OUT BIT(2)
|
|
#define MAX9271_GPIO1OUT BIT(1)
|
|
#define MAX9271_GPO BIT(0)
|
|
/* Register 0x15 */
|
|
#define MAX9271_PCLKDET BIT(0)
|
|
|
|
/**
|
|
* struct max9271_device - max9271 device
|
|
* @client: The i2c client for the max9271 instance
|
|
*/
|
|
struct max9271_device {
|
|
struct i2c_client *client;
|
|
};
|
|
|
|
/**
|
|
* max9271_wake_up() - Wake up the serializer by issuing an i2c transaction
|
|
* @dev: The max9271 device
|
|
*
|
|
* This function shall be called before any other interaction with the
|
|
* serializer.
|
|
*/
|
|
void max9271_wake_up(struct max9271_device *dev);
|
|
|
|
/**
|
|
* max9271_set_serial_link() - Enable/disable serial link
|
|
* @dev: The max9271 device
|
|
* @enable: Serial link enable/disable flag
|
|
*
|
|
* Return 0 on success or a negative error code on failure
|
|
*/
|
|
int max9271_set_serial_link(struct max9271_device *dev, bool enable);
|
|
|
|
/**
|
|
* max9271_configure_i2c() - Configure I2C bus parameters
|
|
* @dev: The max9271 device
|
|
* @i2c_config: The I2C bus configuration bit mask
|
|
*
|
|
* Configure MAX9271 I2C interface. The bus configuration provided in the
|
|
* @i2c_config parameter shall be assembled using bit values defined by the
|
|
* MAX9271_I2C* macros.
|
|
*
|
|
* Return 0 on success or a negative error code on failure
|
|
*/
|
|
int max9271_configure_i2c(struct max9271_device *dev, u8 i2c_config);
|
|
|
|
/**
|
|
* max9271_set_high_threshold() - Enable or disable reverse channel high
|
|
* threshold
|
|
* @dev: The max9271 device
|
|
* @enable: High threshold enable/disable flag
|
|
*
|
|
* Return 0 on success or a negative error code on failure
|
|
*/
|
|
int max9271_set_high_threshold(struct max9271_device *dev, bool enable);
|
|
|
|
/**
|
|
* max9271_configure_gmsl_link() - Configure the GMSL link
|
|
* @dev: The max9271 device
|
|
*
|
|
* FIXME: the GMSL link configuration is currently hardcoded and performed
|
|
* by programming registers 0x04, 0x07 and 0x02.
|
|
*
|
|
* Return 0 on success or a negative error code on failure
|
|
*/
|
|
int max9271_configure_gmsl_link(struct max9271_device *dev);
|
|
|
|
/**
|
|
* max9271_set_gpios() - Set gpio lines to physical high value
|
|
* @dev: The max9271 device
|
|
* @gpio_mask: The mask of gpio lines to set to high value
|
|
*
|
|
* The @gpio_mask parameter shall be assembled using the MAX9271_GP[IO|O]*
|
|
* bit values.
|
|
*
|
|
* Return 0 on success or a negative error code on failure
|
|
*/
|
|
int max9271_set_gpios(struct max9271_device *dev, u8 gpio_mask);
|
|
|
|
/**
|
|
* max9271_clear_gpios() - Set gpio lines to physical low value
|
|
* @dev: The max9271 device
|
|
* @gpio_mask: The mask of gpio lines to set to low value
|
|
*
|
|
* The @gpio_mask parameter shall be assembled using the MAX9271_GP[IO|O]*
|
|
* bit values.
|
|
*
|
|
* Return 0 on success or a negative error code on failure
|
|
*/
|
|
int max9271_clear_gpios(struct max9271_device *dev, u8 gpio_mask);
|
|
|
|
/**
|
|
* max9271_enable_gpios() - Enable gpio lines
|
|
* @dev: The max9271 device
|
|
* @gpio_mask: The mask of gpio lines to enable
|
|
*
|
|
* The @gpio_mask parameter shall be assembled using the MAX9271_GPIO*
|
|
* bit values. GPO line is always enabled by default.
|
|
*
|
|
* Return 0 on success or a negative error code on failure
|
|
*/
|
|
int max9271_enable_gpios(struct max9271_device *dev, u8 gpio_mask);
|
|
|
|
/**
|
|
* max9271_disable_gpios() - Disable gpio lines
|
|
* @dev: The max9271 device
|
|
* @gpio_mask: The mask of gpio lines to disable
|
|
*
|
|
* The @gpio_mask parameter shall be assembled using the MAX9271_GPIO*
|
|
* bit values. GPO line is always enabled by default and cannot be disabled.
|
|
*
|
|
* Return 0 on success or a negative error code on failure
|
|
*/
|
|
int max9271_disable_gpios(struct max9271_device *dev, u8 gpio_mask);
|
|
|
|
/**
|
|
* max9271_verify_id() - Read and verify MAX9271 id
|
|
* @dev: The max9271 device
|
|
*
|
|
* Return 0 on success or a negative error code on failure
|
|
*/
|
|
int max9271_verify_id(struct max9271_device *dev);
|
|
|
|
/**
|
|
* max9271_set_address() - Program a new I2C address
|
|
* @dev: The max9271 device
|
|
* @addr: The new I2C address in 7-bit format
|
|
*
|
|
* This function only takes care of programming the new I2C address @addr to
|
|
* in the MAX9271 chip registers, it is responsiblity of the caller to set
|
|
* the i2c address client to the @addr value to be able to communicate with
|
|
* the MAX9271 chip using the I2C framework APIs after this function returns.
|
|
*
|
|
* Return 0 on success or a negative error code on failure
|
|
*/
|
|
int max9271_set_address(struct max9271_device *dev, u8 addr);
|
|
|
|
/**
|
|
* max9271_set_deserializer_address() - Program the remote deserializer address
|
|
* @dev: The max9271 device
|
|
* @addr: The deserializer I2C address in 7-bit format
|
|
*
|
|
* Return 0 on success or a negative error code on failure
|
|
*/
|
|
int max9271_set_deserializer_address(struct max9271_device *dev, u8 addr);
|
|
|
|
/**
|
|
* max9271_set_translation() - Program I2C address translation
|
|
* @dev: The max9271 device
|
|
* @source: The I2C source address
|
|
* @dest: The I2C destination address
|
|
*
|
|
* Program address translation from @source to @dest. This is required to
|
|
* communicate with local devices that do not support address reprogramming.
|
|
*
|
|
* TODO: The device supports translation of two address, this function currently
|
|
* supports a single one.
|
|
*
|
|
* Return 0 on success or a negative error code on failure
|
|
*/
|
|
int max9271_set_translation(struct max9271_device *dev, u8 source, u8 dest);
|