linux/drivers/usb/serial/io_ti.c
Greg Kroah-Hartman 6ca98bc284 USB: serial: Remove redundant license text
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner.  So the extra GPL text wording
can be removed as it is no longer needed at all.

This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text.  And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.

No copyright headers or other non-license-description text was removed.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-04 11:55:38 +01:00

2819 lines
76 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* Edgeport USB Serial Converter driver
*
* Copyright (C) 2000-2002 Inside Out Networks, All rights reserved.
* Copyright (C) 2001-2002 Greg Kroah-Hartman <greg@kroah.com>
*
* Supports the following devices:
* EP/1 EP/2 EP/4 EP/21 EP/22 EP/221 EP/42 EP/421 WATCHPORT
*
* For questions or problems with this driver, contact Inside Out
* Networks technical support, or Peter Berger <pberger@brimson.com>,
* or Al Borchers <alborchers@steinerpoint.com>.
*/
#include <linux/kernel.h>
#include <linux/jiffies.h>
#include <linux/errno.h>
#include <linux/slab.h>
#include <linux/tty.h>
#include <linux/tty_driver.h>
#include <linux/tty_flip.h>
#include <linux/module.h>
#include <linux/spinlock.h>
#include <linux/mutex.h>
#include <linux/serial.h>
#include <linux/swab.h>
#include <linux/kfifo.h>
#include <linux/ioctl.h>
#include <linux/firmware.h>
#include <linux/uaccess.h>
#include <linux/usb.h>
#include <linux/usb/serial.h>
#include "io_16654.h"
#include "io_usbvend.h"
#include "io_ti.h"
#define DRIVER_AUTHOR "Greg Kroah-Hartman <greg@kroah.com> and David Iacovelli"
#define DRIVER_DESC "Edgeport USB Serial Driver"
#define EPROM_PAGE_SIZE 64
/* different hardware types */
#define HARDWARE_TYPE_930 0
#define HARDWARE_TYPE_TIUMP 1
/* IOCTL_PRIVATE_TI_GET_MODE Definitions */
#define TI_MODE_CONFIGURING 0 /* Device has not entered start device */
#define TI_MODE_BOOT 1 /* Staying in boot mode */
#define TI_MODE_DOWNLOAD 2 /* Made it to download mode */
#define TI_MODE_TRANSITIONING 3 /*
* Currently in boot mode but
* transitioning to download mode
*/
/* read urb state */
#define EDGE_READ_URB_RUNNING 0
#define EDGE_READ_URB_STOPPING 1
#define EDGE_READ_URB_STOPPED 2
#define EDGE_CLOSING_WAIT 4000 /* in .01 sec */
/* Product information read from the Edgeport */
struct product_info {
int TiMode; /* Current TI Mode */
__u8 hardware_type; /* Type of hardware */
} __attribute__((packed));
/*
* Edgeport firmware header
*
* "build_number" has been set to 0 in all three of the images I have
* seen, and Digi Tech Support suggests that it is safe to ignore it.
*
* "length" is the number of bytes of actual data following the header.
*
* "checksum" is the low order byte resulting from adding the values of
* all the data bytes.
*/
struct edgeport_fw_hdr {
u8 major_version;
u8 minor_version;
__le16 build_number;
__le16 length;
u8 checksum;
} __packed;
struct edgeport_port {
__u16 uart_base;
__u16 dma_address;
__u8 shadow_msr;
__u8 shadow_mcr;
__u8 shadow_lsr;
__u8 lsr_mask;
__u32 ump_read_timeout; /*
* Number of milliseconds the UMP will
* wait without data before completing
* a read short
*/
int baud_rate;
int close_pending;
int lsr_event;
struct edgeport_serial *edge_serial;
struct usb_serial_port *port;
__u8 bUartMode; /* Port type, 0: RS232, etc. */
spinlock_t ep_lock;
int ep_read_urb_state;
int ep_write_urb_in_use;
};
struct edgeport_serial {
struct product_info product_info;
u8 TI_I2C_Type; /* Type of I2C in UMP */
u8 TiReadI2C; /*
* Set to TRUE if we have read the
* I2c in Boot Mode
*/
struct mutex es_lock;
int num_ports_open;
struct usb_serial *serial;
struct delayed_work heartbeat_work;
int fw_version;
bool use_heartbeat;
};
/* Devices that this driver supports */
static const struct usb_device_id edgeport_1port_id_table[] = {
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_1) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_TI3410_EDGEPORT_1) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_TI3410_EDGEPORT_1I) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_PROXIMITY) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_MOTION) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_MOISTURE) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_TEMPERATURE) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_HUMIDITY) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_POWER) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_LIGHT) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_RADIATION) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_DISTANCE) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_ACCELERATION) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_PROX_DIST) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_PLUS_PWR_HP4CD) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_PLUS_PWR_PCI) },
{ }
};
static const struct usb_device_id edgeport_2port_id_table[] = {
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2C) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2I) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_421) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_21) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_42) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4I) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_22I) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_221C) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_22C) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_21C) },
/* The 4, 8 and 16 port devices show up as multiple 2 port devices */
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4S) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_8) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_8S) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_416) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_416B) },
{ }
};
/* Devices that this driver supports */
static const struct usb_device_id id_table_combined[] = {
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_1) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_TI3410_EDGEPORT_1) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_TI3410_EDGEPORT_1I) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_PROXIMITY) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_MOTION) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_MOISTURE) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_TEMPERATURE) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_HUMIDITY) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_POWER) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_LIGHT) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_RADIATION) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_DISTANCE) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_ACCELERATION) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_PROX_DIST) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_PLUS_PWR_HP4CD) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_PLUS_PWR_PCI) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2C) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2I) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_421) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_21) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_42) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4I) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_22I) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_221C) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_22C) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_21C) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4S) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_8) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_8S) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_416) },
{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_416B) },
{ }
};
MODULE_DEVICE_TABLE(usb, id_table_combined);
static int closing_wait = EDGE_CLOSING_WAIT;
static bool ignore_cpu_rev;
static int default_uart_mode; /* RS232 */
static void edge_tty_recv(struct usb_serial_port *port, unsigned char *data,
int length);
static void stop_read(struct edgeport_port *edge_port);
static int restart_read(struct edgeport_port *edge_port);
static void edge_set_termios(struct tty_struct *tty,
struct usb_serial_port *port, struct ktermios *old_termios);
static void edge_send(struct usb_serial_port *port, struct tty_struct *tty);
static int do_download_mode(struct edgeport_serial *serial,
const struct firmware *fw);
static int do_boot_mode(struct edgeport_serial *serial,
const struct firmware *fw);
/* sysfs attributes */
static int edge_create_sysfs_attrs(struct usb_serial_port *port);
static int edge_remove_sysfs_attrs(struct usb_serial_port *port);
/*
* Some release of Edgeport firmware "down3.bin" after version 4.80
* introduced code to automatically disconnect idle devices on some
* Edgeport models after periods of inactivity, typically ~60 seconds.
* This occurs without regard to whether ports on the device are open
* or not. Digi International Tech Support suggested:
*
* 1. Adding driver "heartbeat" code to reset the firmware timer by
* requesting a descriptor record every 15 seconds, which should be
* effective with newer firmware versions that require it, and benign
* with older versions that do not. In practice 40 seconds seems often
* enough.
* 2. The heartbeat code is currently required only on Edgeport/416 models.
*/
#define FW_HEARTBEAT_VERSION_CUTOFF ((4 << 8) + 80)
#define FW_HEARTBEAT_SECS 40
/* Timeouts in msecs: firmware downloads take longer */
#define TI_VSEND_TIMEOUT_DEFAULT 1000
#define TI_VSEND_TIMEOUT_FW_DOWNLOAD 10000
static int ti_vread_sync(struct usb_device *dev, __u8 request,
__u16 value, __u16 index, u8 *data, int size)
{
int status;
status = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), request,
(USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN),
value, index, data, size, 1000);
if (status < 0)
return status;
if (status != size) {
dev_dbg(&dev->dev, "%s - wanted to write %d, but only wrote %d\n",
__func__, size, status);
return -ECOMM;
}
return 0;
}
static int ti_vsend_sync(struct usb_device *dev, u8 request, u16 value,
u16 index, u8 *data, int size, int timeout)
{
int status;
status = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), request,
(USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT),
value, index, data, size, timeout);
if (status < 0)
return status;
if (status != size) {
dev_dbg(&dev->dev, "%s - wanted to write %d, but only wrote %d\n",
__func__, size, status);
return -ECOMM;
}
return 0;
}
static int send_cmd(struct usb_device *dev, __u8 command,
__u8 moduleid, __u16 value, u8 *data,
int size)
{
return ti_vsend_sync(dev, command, value, moduleid, data, size,
TI_VSEND_TIMEOUT_DEFAULT);
}
/* clear tx/rx buffers and fifo in TI UMP */
static int purge_port(struct usb_serial_port *port, __u16 mask)
{
int port_number = port->port_number;
dev_dbg(&port->dev, "%s - port %d, mask %x\n", __func__, port_number, mask);
return send_cmd(port->serial->dev,
UMPC_PURGE_PORT,
(__u8)(UMPM_UART1_PORT + port_number),
mask,
NULL,
0);
}
/**
* read_download_mem - Read edgeport memory from TI chip
* @dev: usb device pointer
* @start_address: Device CPU address at which to read
* @length: Length of above data
* @address_type: Can read both XDATA and I2C
* @buffer: pointer to input data buffer
*/
static int read_download_mem(struct usb_device *dev, int start_address,
int length, __u8 address_type, __u8 *buffer)
{
int status = 0;
__u8 read_length;
u16 be_start_address;
dev_dbg(&dev->dev, "%s - @ %x for %d\n", __func__, start_address, length);
/*
* Read in blocks of 64 bytes
* (TI firmware can't handle more than 64 byte reads)
*/
while (length) {
if (length > 64)
read_length = 64;
else
read_length = (__u8)length;
if (read_length > 1) {
dev_dbg(&dev->dev, "%s - @ %x for %d\n", __func__, start_address, read_length);
}
/*
* NOTE: Must use swab as wIndex is sent in little-endian
* byte order regardless of host byte order.
*/
be_start_address = swab16((u16)start_address);
status = ti_vread_sync(dev, UMPC_MEMORY_READ,
(__u16)address_type,
be_start_address,
buffer, read_length);
if (status) {
dev_dbg(&dev->dev, "%s - ERROR %x\n", __func__, status);
return status;
}
if (read_length > 1)
usb_serial_debug_data(&dev->dev, __func__, read_length, buffer);
/* Update pointers/length */
start_address += read_length;
buffer += read_length;
length -= read_length;
}
return status;
}
static int read_ram(struct usb_device *dev, int start_address,
int length, __u8 *buffer)
{
return read_download_mem(dev, start_address, length,
DTK_ADDR_SPACE_XDATA, buffer);
}
/* Read edgeport memory to a given block */
static int read_boot_mem(struct edgeport_serial *serial,
int start_address, int length, __u8 *buffer)
{
int status = 0;
int i;
for (i = 0; i < length; i++) {
status = ti_vread_sync(serial->serial->dev,
UMPC_MEMORY_READ, serial->TI_I2C_Type,
(__u16)(start_address+i), &buffer[i], 0x01);
if (status) {
dev_dbg(&serial->serial->dev->dev, "%s - ERROR %x\n", __func__, status);
return status;
}
}
dev_dbg(&serial->serial->dev->dev, "%s - start_address = %x, length = %d\n",
__func__, start_address, length);
usb_serial_debug_data(&serial->serial->dev->dev, __func__, length, buffer);
serial->TiReadI2C = 1;
return status;
}
/* Write given block to TI EPROM memory */
static int write_boot_mem(struct edgeport_serial *serial,
int start_address, int length, __u8 *buffer)
{
int status = 0;
int i;
u8 *temp;
/* Must do a read before write */
if (!serial->TiReadI2C) {
temp = kmalloc(1, GFP_KERNEL);
if (!temp)
return -ENOMEM;
status = read_boot_mem(serial, 0, 1, temp);
kfree(temp);
if (status)
return status;
}
for (i = 0; i < length; ++i) {
status = ti_vsend_sync(serial->serial->dev, UMPC_MEMORY_WRITE,
buffer[i], (u16)(i + start_address), NULL,
0, TI_VSEND_TIMEOUT_DEFAULT);
if (status)
return status;
}
dev_dbg(&serial->serial->dev->dev, "%s - start_sddr = %x, length = %d\n", __func__, start_address, length);
usb_serial_debug_data(&serial->serial->dev->dev, __func__, length, buffer);
return status;
}
/* Write edgeport I2C memory to TI chip */
static int write_i2c_mem(struct edgeport_serial *serial,
int start_address, int length, __u8 address_type, __u8 *buffer)
{
struct device *dev = &serial->serial->dev->dev;
int status = 0;
int write_length;
u16 be_start_address;
/* We can only send a maximum of 1 aligned byte page at a time */
/* calculate the number of bytes left in the first page */
write_length = EPROM_PAGE_SIZE -
(start_address & (EPROM_PAGE_SIZE - 1));
if (write_length > length)
write_length = length;
dev_dbg(dev, "%s - BytesInFirstPage Addr = %x, length = %d\n",
__func__, start_address, write_length);
usb_serial_debug_data(dev, __func__, write_length, buffer);
/*
* Write first page.
*
* NOTE: Must use swab as wIndex is sent in little-endian byte order
* regardless of host byte order.
*/
be_start_address = swab16((u16)start_address);
status = ti_vsend_sync(serial->serial->dev, UMPC_MEMORY_WRITE,
(u16)address_type, be_start_address,
buffer, write_length, TI_VSEND_TIMEOUT_DEFAULT);
if (status) {
dev_dbg(dev, "%s - ERROR %d\n", __func__, status);
return status;
}
length -= write_length;
start_address += write_length;
buffer += write_length;
/*
* We should be aligned now -- can write max page size bytes at a
* time.
*/
while (length) {
if (length > EPROM_PAGE_SIZE)
write_length = EPROM_PAGE_SIZE;
else
write_length = length;
dev_dbg(dev, "%s - Page Write Addr = %x, length = %d\n",
__func__, start_address, write_length);
usb_serial_debug_data(dev, __func__, write_length, buffer);
/*
* Write next page.
*
* NOTE: Must use swab as wIndex is sent in little-endian byte
* order regardless of host byte order.
*/
be_start_address = swab16((u16)start_address);
status = ti_vsend_sync(serial->serial->dev, UMPC_MEMORY_WRITE,
(u16)address_type, be_start_address, buffer,
write_length, TI_VSEND_TIMEOUT_DEFAULT);
if (status) {
dev_err(dev, "%s - ERROR %d\n", __func__, status);
return status;
}
length -= write_length;
start_address += write_length;
buffer += write_length;
}
return status;
}
/*
* Examine the UMP DMA registers and LSR
*
* Check the MSBit of the X and Y DMA byte count registers.
* A zero in this bit indicates that the TX DMA buffers are empty
* then check the TX Empty bit in the UART.
*/
static int tx_active(struct edgeport_port *port)
{
int status;
struct out_endpoint_desc_block *oedb;
__u8 *lsr;
int bytes_left = 0;
oedb = kmalloc(sizeof(*oedb), GFP_KERNEL);
if (!oedb)
return -ENOMEM;
/*
* Sigh, that's right, just one byte, as not all platforms can
* do DMA from stack
*/
lsr = kmalloc(1, GFP_KERNEL);
if (!lsr) {
kfree(oedb);
return -ENOMEM;
}
/* Read the DMA Count Registers */
status = read_ram(port->port->serial->dev, port->dma_address,
sizeof(*oedb), (void *)oedb);
if (status)
goto exit_is_tx_active;
dev_dbg(&port->port->dev, "%s - XByteCount 0x%X\n", __func__, oedb->XByteCount);
/* and the LSR */
status = read_ram(port->port->serial->dev,
port->uart_base + UMPMEM_OFFS_UART_LSR, 1, lsr);
if (status)
goto exit_is_tx_active;
dev_dbg(&port->port->dev, "%s - LSR = 0x%X\n", __func__, *lsr);
/* If either buffer has data or we are transmitting then return TRUE */
if ((oedb->XByteCount & 0x80) != 0)
bytes_left += 64;
if ((*lsr & UMP_UART_LSR_TX_MASK) == 0)
bytes_left += 1;
/* We return Not Active if we get any kind of error */
exit_is_tx_active:
dev_dbg(&port->port->dev, "%s - return %d\n", __func__, bytes_left);
kfree(lsr);
kfree(oedb);
return bytes_left;
}
static int choose_config(struct usb_device *dev)
{
/*
* There may be multiple configurations on this device, in which case
* we would need to read and parse all of them to find out which one
* we want. However, we just support one config at this point,
* configuration # 1, which is Config Descriptor 0.
*/
dev_dbg(&dev->dev, "%s - Number of Interfaces = %d\n",
__func__, dev->config->desc.bNumInterfaces);
dev_dbg(&dev->dev, "%s - MAX Power = %d\n",
__func__, dev->config->desc.bMaxPower * 2);
if (dev->config->desc.bNumInterfaces != 1) {
dev_err(&dev->dev, "%s - bNumInterfaces is not 1, ERROR!\n", __func__);
return -ENODEV;
}
return 0;
}
static int read_rom(struct edgeport_serial *serial,
int start_address, int length, __u8 *buffer)
{
int status;
if (serial->product_info.TiMode == TI_MODE_DOWNLOAD) {
status = read_download_mem(serial->serial->dev,
start_address,
length,
serial->TI_I2C_Type,
buffer);
} else {
status = read_boot_mem(serial, start_address, length,
buffer);
}
return status;
}
static int write_rom(struct edgeport_serial *serial, int start_address,
int length, __u8 *buffer)
{
if (serial->product_info.TiMode == TI_MODE_BOOT)
return write_boot_mem(serial, start_address, length,
buffer);
if (serial->product_info.TiMode == TI_MODE_DOWNLOAD)
return write_i2c_mem(serial, start_address, length,
serial->TI_I2C_Type, buffer);
return -EINVAL;
}
/* Read a descriptor header from I2C based on type */
static int get_descriptor_addr(struct edgeport_serial *serial,
int desc_type, struct ti_i2c_desc *rom_desc)
{
int start_address;
int status;
/* Search for requested descriptor in I2C */
start_address = 2;
do {
status = read_rom(serial,
start_address,
sizeof(struct ti_i2c_desc),
(__u8 *)rom_desc);
if (status)
return 0;
if (rom_desc->Type == desc_type)
return start_address;
start_address = start_address + sizeof(struct ti_i2c_desc) +
le16_to_cpu(rom_desc->Size);
} while ((start_address < TI_MAX_I2C_SIZE) && rom_desc->Type);
return 0;
}
/* Validate descriptor checksum */
static int valid_csum(struct ti_i2c_desc *rom_desc, __u8 *buffer)
{
__u16 i;
__u8 cs = 0;
for (i = 0; i < le16_to_cpu(rom_desc->Size); i++)
cs = (__u8)(cs + buffer[i]);
if (cs != rom_desc->CheckSum) {
pr_debug("%s - Mismatch %x - %x", __func__, rom_desc->CheckSum, cs);
return -EINVAL;
}
return 0;
}
/* Make sure that the I2C image is good */
static int check_i2c_image(struct edgeport_serial *serial)
{
struct device *dev = &serial->serial->dev->dev;
int status = 0;
struct ti_i2c_desc *rom_desc;
int start_address = 2;
__u8 *buffer;
__u16 ttype;
rom_desc = kmalloc(sizeof(*rom_desc), GFP_KERNEL);
if (!rom_desc)
return -ENOMEM;
buffer = kmalloc(TI_MAX_I2C_SIZE, GFP_KERNEL);
if (!buffer) {
kfree(rom_desc);
return -ENOMEM;
}
/* Read the first byte (Signature0) must be 0x52 or 0x10 */
status = read_rom(serial, 0, 1, buffer);
if (status)
goto out;
if (*buffer != UMP5152 && *buffer != UMP3410) {
dev_err(dev, "%s - invalid buffer signature\n", __func__);
status = -ENODEV;
goto out;
}
do {
/* Validate the I2C */
status = read_rom(serial,
start_address,
sizeof(struct ti_i2c_desc),
(__u8 *)rom_desc);
if (status)
break;
if ((start_address + sizeof(struct ti_i2c_desc) +
le16_to_cpu(rom_desc->Size)) > TI_MAX_I2C_SIZE) {
status = -ENODEV;
dev_dbg(dev, "%s - structure too big, erroring out.\n", __func__);
break;
}
dev_dbg(dev, "%s Type = 0x%x\n", __func__, rom_desc->Type);
/* Skip type 2 record */
ttype = rom_desc->Type & 0x0f;
if (ttype != I2C_DESC_TYPE_FIRMWARE_BASIC
&& ttype != I2C_DESC_TYPE_FIRMWARE_AUTO) {
/* Read the descriptor data */
status = read_rom(serial, start_address +
sizeof(struct ti_i2c_desc),
le16_to_cpu(rom_desc->Size),
buffer);
if (status)
break;
status = valid_csum(rom_desc, buffer);
if (status)
break;
}
start_address = start_address + sizeof(struct ti_i2c_desc) +
le16_to_cpu(rom_desc->Size);
} while ((rom_desc->Type != I2C_DESC_TYPE_ION) &&
(start_address < TI_MAX_I2C_SIZE));
if ((rom_desc->Type != I2C_DESC_TYPE_ION) ||
(start_address > TI_MAX_I2C_SIZE))
status = -ENODEV;
out:
kfree(buffer);
kfree(rom_desc);
return status;
}
static int get_manuf_info(struct edgeport_serial *serial, __u8 *buffer)
{
int status;
int start_address;
struct ti_i2c_desc *rom_desc;
struct edge_ti_manuf_descriptor *desc;
struct device *dev = &serial->serial->dev->dev;
rom_desc = kmalloc(sizeof(*rom_desc), GFP_KERNEL);
if (!rom_desc)
return -ENOMEM;
start_address = get_descriptor_addr(serial, I2C_DESC_TYPE_ION,
rom_desc);
if (!start_address) {
dev_dbg(dev, "%s - Edge Descriptor not found in I2C\n", __func__);
status = -ENODEV;
goto exit;
}
/* Read the descriptor data */
status = read_rom(serial, start_address+sizeof(struct ti_i2c_desc),
le16_to_cpu(rom_desc->Size), buffer);
if (status)
goto exit;
status = valid_csum(rom_desc, buffer);
desc = (struct edge_ti_manuf_descriptor *)buffer;
dev_dbg(dev, "%s - IonConfig 0x%x\n", __func__, desc->IonConfig);
dev_dbg(dev, "%s - Version %d\n", __func__, desc->Version);
dev_dbg(dev, "%s - Cpu/Board 0x%x\n", __func__, desc->CpuRev_BoardRev);
dev_dbg(dev, "%s - NumPorts %d\n", __func__, desc->NumPorts);
dev_dbg(dev, "%s - NumVirtualPorts %d\n", __func__, desc->NumVirtualPorts);
dev_dbg(dev, "%s - TotalPorts %d\n", __func__, desc->TotalPorts);
exit:
kfree(rom_desc);
return status;
}
/* Build firmware header used for firmware update */
static int build_i2c_fw_hdr(u8 *header, const struct firmware *fw)
{
__u8 *buffer;
int buffer_size;
int i;
__u8 cs = 0;
struct ti_i2c_desc *i2c_header;
struct ti_i2c_image_header *img_header;
struct ti_i2c_firmware_rec *firmware_rec;
struct edgeport_fw_hdr *fw_hdr = (struct edgeport_fw_hdr *)fw->data;
/*
* In order to update the I2C firmware we must change the type 2 record
* to type 0xF2. This will force the UMP to come up in Boot Mode.
* Then while in boot mode, the driver will download the latest
* firmware (padded to 15.5k) into the UMP ram. And finally when the
* device comes back up in download mode the driver will cause the new
* firmware to be copied from the UMP Ram to I2C and the firmware will
* update the record type from 0xf2 to 0x02.
*/
/*
* Allocate a 15.5k buffer + 2 bytes for version number (Firmware
* Record)
*/
buffer_size = (((1024 * 16) - 512 ) +
sizeof(struct ti_i2c_firmware_rec));
buffer = kmalloc(buffer_size, GFP_KERNEL);
if (!buffer)
return -ENOMEM;
/* Set entire image of 0xffs */
memset(buffer, 0xff, buffer_size);
/* Copy version number into firmware record */
firmware_rec = (struct ti_i2c_firmware_rec *)buffer;
firmware_rec->Ver_Major = fw_hdr->major_version;
firmware_rec->Ver_Minor = fw_hdr->minor_version;
/* Pointer to fw_down memory image */
img_header = (struct ti_i2c_image_header *)&fw->data[4];
memcpy(buffer + sizeof(struct ti_i2c_firmware_rec),
&fw->data[4 + sizeof(struct ti_i2c_image_header)],
le16_to_cpu(img_header->Length));
for (i=0; i < buffer_size; i++) {
cs = (__u8)(cs + buffer[i]);
}
kfree(buffer);
/* Build new header */
i2c_header = (struct ti_i2c_desc *)header;
firmware_rec = (struct ti_i2c_firmware_rec*)i2c_header->Data;
i2c_header->Type = I2C_DESC_TYPE_FIRMWARE_BLANK;
i2c_header->Size = cpu_to_le16(buffer_size);
i2c_header->CheckSum = cs;
firmware_rec->Ver_Major = fw_hdr->major_version;
firmware_rec->Ver_Minor = fw_hdr->minor_version;
return 0;
}
/* Try to figure out what type of I2c we have */
static int i2c_type_bootmode(struct edgeport_serial *serial)
{
struct device *dev = &serial->serial->dev->dev;
int status;
u8 *data;
data = kmalloc(1, GFP_KERNEL);
if (!data)
return -ENOMEM;
/* Try to read type 2 */
status = ti_vread_sync(serial->serial->dev, UMPC_MEMORY_READ,
DTK_ADDR_SPACE_I2C_TYPE_II, 0, data, 0x01);
if (status)
dev_dbg(dev, "%s - read 2 status error = %d\n", __func__, status);
else
dev_dbg(dev, "%s - read 2 data = 0x%x\n", __func__, *data);
if ((!status) && (*data == UMP5152 || *data == UMP3410)) {
dev_dbg(dev, "%s - ROM_TYPE_II\n", __func__);
serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_II;
goto out;
}
/* Try to read type 3 */
status = ti_vread_sync(serial->serial->dev, UMPC_MEMORY_READ,
DTK_ADDR_SPACE_I2C_TYPE_III, 0, data, 0x01);
if (status)
dev_dbg(dev, "%s - read 3 status error = %d\n", __func__, status);
else
dev_dbg(dev, "%s - read 2 data = 0x%x\n", __func__, *data);
if ((!status) && (*data == UMP5152 || *data == UMP3410)) {
dev_dbg(dev, "%s - ROM_TYPE_III\n", __func__);
serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_III;
goto out;
}
dev_dbg(dev, "%s - Unknown\n", __func__);
serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_II;
status = -ENODEV;
out:
kfree(data);
return status;
}
static int bulk_xfer(struct usb_serial *serial, void *buffer,
int length, int *num_sent)
{
int status;
status = usb_bulk_msg(serial->dev,
usb_sndbulkpipe(serial->dev,
serial->port[0]->bulk_out_endpointAddress),
buffer, length, num_sent, 1000);
return status;
}
/* Download given firmware image to the device (IN BOOT MODE) */
static int download_code(struct edgeport_serial *serial, __u8 *image,
int image_length)
{
int status = 0;
int pos;
int transfer;
int done;
/* Transfer firmware image */
for (pos = 0; pos < image_length; ) {
/* Read the next buffer from file */
transfer = image_length - pos;
if (transfer > EDGE_FW_BULK_MAX_PACKET_SIZE)
transfer = EDGE_FW_BULK_MAX_PACKET_SIZE;
/* Transfer data */
status = bulk_xfer(serial->serial, &image[pos],
transfer, &done);
if (status)
break;
/* Advance buffer pointer */
pos += done;
}
return status;
}
/* FIXME!!! */
static int config_boot_dev(struct usb_device *dev)
{
return 0;
}
static int ti_cpu_rev(struct edge_ti_manuf_descriptor *desc)
{
return TI_GET_CPU_REVISION(desc->CpuRev_BoardRev);
}
static int check_fw_sanity(struct edgeport_serial *serial,
const struct firmware *fw)
{
u16 length_total;
u8 checksum = 0;
int pos;
struct device *dev = &serial->serial->interface->dev;
struct edgeport_fw_hdr *fw_hdr = (struct edgeport_fw_hdr *)fw->data;
if (fw->size < sizeof(struct edgeport_fw_hdr)) {
dev_err(dev, "incomplete fw header\n");
return -EINVAL;
}
length_total = le16_to_cpu(fw_hdr->length) +
sizeof(struct edgeport_fw_hdr);
if (fw->size != length_total) {
dev_err(dev, "bad fw size (expected: %u, got: %zu)\n",
length_total, fw->size);
return -EINVAL;
}
for (pos = sizeof(struct edgeport_fw_hdr); pos < fw->size; ++pos)
checksum += fw->data[pos];
if (checksum != fw_hdr->checksum) {
dev_err(dev, "bad fw checksum (expected: 0x%x, got: 0x%x)\n",
fw_hdr->checksum, checksum);
return -EINVAL;
}
return 0;
}
/*
* DownloadTIFirmware - Download run-time operating firmware to the TI5052
*
* This routine downloads the main operating code into the TI5052, using the
* boot code already burned into E2PROM or ROM.
*/
static int download_fw(struct edgeport_serial *serial)
{
struct device *dev = &serial->serial->interface->dev;
int status = 0;
struct usb_interface_descriptor *interface;
const struct firmware *fw;
const char *fw_name = "edgeport/down3.bin";
struct edgeport_fw_hdr *fw_hdr;
status = request_firmware(&fw, fw_name, dev);
if (status) {
dev_err(dev, "Failed to load image \"%s\" err %d\n",
fw_name, status);
return status;
}
if (check_fw_sanity(serial, fw)) {
status = -EINVAL;
goto out;
}
fw_hdr = (struct edgeport_fw_hdr *)fw->data;
/* If on-board version is newer, "fw_version" will be updated later. */
serial->fw_version = (fw_hdr->major_version << 8) +
fw_hdr->minor_version;
/*
* This routine is entered by both the BOOT mode and the Download mode
* We can determine which code is running by the reading the config
* descriptor and if we have only one bulk pipe it is in boot mode
*/
serial->product_info.hardware_type = HARDWARE_TYPE_TIUMP;
/* Default to type 2 i2c */
serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_II;
status = choose_config(serial->serial->dev);
if (status)
goto out;
interface = &serial->serial->interface->cur_altsetting->desc;
if (!interface) {
dev_err(dev, "%s - no interface set, error!\n", __func__);
status = -ENODEV;
goto out;
}
/*
* Setup initial mode -- the default mode 0 is TI_MODE_CONFIGURING
* if we have more than one endpoint we are definitely in download
* mode
*/
if (interface->bNumEndpoints > 1) {
serial->product_info.TiMode = TI_MODE_DOWNLOAD;
status = do_download_mode(serial, fw);
} else {
/* Otherwise we will remain in configuring mode */
serial->product_info.TiMode = TI_MODE_CONFIGURING;
status = do_boot_mode(serial, fw);
}
out:
release_firmware(fw);
return status;
}
static int do_download_mode(struct edgeport_serial *serial,
const struct firmware *fw)
{
struct device *dev = &serial->serial->interface->dev;
int status = 0;
int start_address;
struct edge_ti_manuf_descriptor *ti_manuf_desc;
int download_cur_ver;
int download_new_ver;
struct edgeport_fw_hdr *fw_hdr = (struct edgeport_fw_hdr *)fw->data;
struct ti_i2c_desc *rom_desc;
dev_dbg(dev, "%s - RUNNING IN DOWNLOAD MODE\n", __func__);
status = check_i2c_image(serial);
if (status) {
dev_dbg(dev, "%s - DOWNLOAD MODE -- BAD I2C\n", __func__);
return status;
}
/*
* Validate Hardware version number
* Read Manufacturing Descriptor from TI Based Edgeport
*/
ti_manuf_desc = kmalloc(sizeof(*ti_manuf_desc), GFP_KERNEL);
if (!ti_manuf_desc)
return -ENOMEM;
status = get_manuf_info(serial, (__u8 *)ti_manuf_desc);
if (status) {
kfree(ti_manuf_desc);
return status;
}
/* Check version number of ION descriptor */
if (!ignore_cpu_rev && ti_cpu_rev(ti_manuf_desc) < 2) {
dev_dbg(dev, "%s - Wrong CPU Rev %d (Must be 2)\n",
__func__, ti_cpu_rev(ti_manuf_desc));
kfree(ti_manuf_desc);
return -EINVAL;
}
rom_desc = kmalloc(sizeof(*rom_desc), GFP_KERNEL);
if (!rom_desc) {
kfree(ti_manuf_desc);
return -ENOMEM;
}
/* Search for type 2 record (firmware record) */
start_address = get_descriptor_addr(serial,
I2C_DESC_TYPE_FIRMWARE_BASIC, rom_desc);
if (start_address != 0) {
struct ti_i2c_firmware_rec *firmware_version;
u8 *record;
dev_dbg(dev, "%s - Found Type FIRMWARE (Type 2) record\n",
__func__);
firmware_version = kmalloc(sizeof(*firmware_version),
GFP_KERNEL);
if (!firmware_version) {
kfree(rom_desc);
kfree(ti_manuf_desc);
return -ENOMEM;
}
/*
* Validate version number
* Read the descriptor data
*/
status = read_rom(serial, start_address +
sizeof(struct ti_i2c_desc),
sizeof(struct ti_i2c_firmware_rec),
(__u8 *)firmware_version);
if (status) {
kfree(firmware_version);
kfree(rom_desc);
kfree(ti_manuf_desc);
return status;
}
/*
* Check version number of download with current
* version in I2c
*/
download_cur_ver = (firmware_version->Ver_Major << 8) +
(firmware_version->Ver_Minor);
download_new_ver = (fw_hdr->major_version << 8) +
(fw_hdr->minor_version);
dev_dbg(dev, "%s - >> FW Versions Device %d.%d Driver %d.%d\n",
__func__, firmware_version->Ver_Major,
firmware_version->Ver_Minor,
fw_hdr->major_version, fw_hdr->minor_version);
/*
* Check if we have an old version in the I2C and
* update if necessary
*/
if (download_cur_ver < download_new_ver) {
dev_dbg(dev, "%s - Update I2C dld from %d.%d to %d.%d\n",
__func__,
firmware_version->Ver_Major,
firmware_version->Ver_Minor,
fw_hdr->major_version,
fw_hdr->minor_version);
record = kmalloc(1, GFP_KERNEL);
if (!record) {
kfree(firmware_version);
kfree(rom_desc);
kfree(ti_manuf_desc);
return -ENOMEM;
}
/*
* In order to update the I2C firmware we must
* change the type 2 record to type 0xF2. This
* will force the UMP to come up in Boot Mode.
* Then while in boot mode, the driver will
* download the latest firmware (padded to
* 15.5k) into the UMP ram. Finally when the
* device comes back up in download mode the
* driver will cause the new firmware to be
* copied from the UMP Ram to I2C and the
* firmware will update the record type from
* 0xf2 to 0x02.
*/
*record = I2C_DESC_TYPE_FIRMWARE_BLANK;
/*
* Change the I2C Firmware record type to
* 0xf2 to trigger an update
*/
status = write_rom(serial, start_address,
sizeof(*record), record);
if (status) {
kfree(record);
kfree(firmware_version);
kfree(rom_desc);
kfree(ti_manuf_desc);
return status;
}
/*
* verify the write -- must do this in order
* for write to complete before we do the
* hardware reset
*/
status = read_rom(serial,
start_address,
sizeof(*record),
record);
if (status) {
kfree(record);
kfree(firmware_version);
kfree(rom_desc);
kfree(ti_manuf_desc);
return status;
}
if (*record != I2C_DESC_TYPE_FIRMWARE_BLANK) {
dev_err(dev, "%s - error resetting device\n",
__func__);
kfree(record);
kfree(firmware_version);
kfree(rom_desc);
kfree(ti_manuf_desc);
return -ENODEV;
}
dev_dbg(dev, "%s - HARDWARE RESET\n", __func__);
/* Reset UMP -- Back to BOOT MODE */
status = ti_vsend_sync(serial->serial->dev,
UMPC_HARDWARE_RESET,
0, 0, NULL, 0,
TI_VSEND_TIMEOUT_DEFAULT);
dev_dbg(dev, "%s - HARDWARE RESET return %d\n",
__func__, status);
/* return an error on purpose. */
kfree(record);
kfree(firmware_version);
kfree(rom_desc);
kfree(ti_manuf_desc);
return -ENODEV;
}
/* Same or newer fw version is already loaded */
serial->fw_version = download_cur_ver;
kfree(firmware_version);
}
/* Search for type 0xF2 record (firmware blank record) */
else {
start_address = get_descriptor_addr(serial,
I2C_DESC_TYPE_FIRMWARE_BLANK, rom_desc);
if (start_address != 0) {
#define HEADER_SIZE (sizeof(struct ti_i2c_desc) + \
sizeof(struct ti_i2c_firmware_rec))
__u8 *header;
__u8 *vheader;
header = kmalloc(HEADER_SIZE, GFP_KERNEL);
if (!header) {
kfree(rom_desc);
kfree(ti_manuf_desc);
return -ENOMEM;
}
vheader = kmalloc(HEADER_SIZE, GFP_KERNEL);
if (!vheader) {
kfree(header);
kfree(rom_desc);
kfree(ti_manuf_desc);
return -ENOMEM;
}
dev_dbg(dev, "%s - Found Type BLANK FIRMWARE (Type F2) record\n",
__func__);
/*
* In order to update the I2C firmware we must change
* the type 2 record to type 0xF2. This will force the
* UMP to come up in Boot Mode. Then while in boot
* mode, the driver will download the latest firmware
* (padded to 15.5k) into the UMP ram. Finally when the
* device comes back up in download mode the driver
* will cause the new firmware to be copied from the
* UMP Ram to I2C and the firmware will update the
* record type from 0xf2 to 0x02.
*/
status = build_i2c_fw_hdr(header, fw);
if (status) {
kfree(vheader);
kfree(header);
kfree(rom_desc);
kfree(ti_manuf_desc);
return -EINVAL;
}
/*
* Update I2C with type 0xf2 record with correct
* size and checksum
*/
status = write_rom(serial,
start_address,
HEADER_SIZE,
header);
if (status) {
kfree(vheader);
kfree(header);
kfree(rom_desc);
kfree(ti_manuf_desc);
return -EINVAL;
}
/*
* verify the write -- must do this in order for
* write to complete before we do the hardware reset
*/
status = read_rom(serial, start_address,
HEADER_SIZE, vheader);
if (status) {
dev_dbg(dev, "%s - can't read header back\n",
__func__);
kfree(vheader);
kfree(header);
kfree(rom_desc);
kfree(ti_manuf_desc);
return status;
}
if (memcmp(vheader, header, HEADER_SIZE)) {
dev_dbg(dev, "%s - write download record failed\n",
__func__);
kfree(vheader);
kfree(header);
kfree(rom_desc);
kfree(ti_manuf_desc);
return -EINVAL;
}
kfree(vheader);
kfree(header);
dev_dbg(dev, "%s - Start firmware update\n", __func__);
/* Tell firmware to copy download image into I2C */
status = ti_vsend_sync(serial->serial->dev,
UMPC_COPY_DNLD_TO_I2C,
0, 0, NULL, 0,
TI_VSEND_TIMEOUT_FW_DOWNLOAD);
dev_dbg(dev, "%s - Update complete 0x%x\n", __func__,
status);
if (status) {
dev_err(dev,
"%s - UMPC_COPY_DNLD_TO_I2C failed\n",
__func__);
kfree(rom_desc);
kfree(ti_manuf_desc);
return status;
}
}
}
/* The device is running the download code */
kfree(rom_desc);
kfree(ti_manuf_desc);
return 0;
}
static int do_boot_mode(struct edgeport_serial *serial,
const struct firmware *fw)
{
struct device *dev = &serial->serial->interface->dev;
int status = 0;
struct edge_ti_manuf_descriptor *ti_manuf_desc;
struct edgeport_fw_hdr *fw_hdr = (struct edgeport_fw_hdr *)fw->data;
dev_dbg(dev, "%s - RUNNING IN BOOT MODE\n", __func__);
/* Configure the TI device so we can use the BULK pipes for download */
status = config_boot_dev(serial->serial->dev);
if (status)
return status;
if (le16_to_cpu(serial->serial->dev->descriptor.idVendor)
!= USB_VENDOR_ID_ION) {
dev_dbg(dev, "%s - VID = 0x%x\n", __func__,
le16_to_cpu(serial->serial->dev->descriptor.idVendor));
serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_II;
goto stayinbootmode;
}
/*
* We have an ION device (I2c Must be programmed)
* Determine I2C image type
*/
if (i2c_type_bootmode(serial))
goto stayinbootmode;
/* Check for ION Vendor ID and that the I2C is valid */
if (!check_i2c_image(serial)) {
struct ti_i2c_image_header *header;
int i;
__u8 cs = 0;
__u8 *buffer;
int buffer_size;
/*
* Validate Hardware version number
* Read Manufacturing Descriptor from TI Based Edgeport
*/
ti_manuf_desc = kmalloc(sizeof(*ti_manuf_desc), GFP_KERNEL);
if (!ti_manuf_desc)
return -ENOMEM;
status = get_manuf_info(serial, (__u8 *)ti_manuf_desc);
if (status) {
kfree(ti_manuf_desc);
goto stayinbootmode;
}
/* Check for version 2 */
if (!ignore_cpu_rev && ti_cpu_rev(ti_manuf_desc) < 2) {
dev_dbg(dev, "%s - Wrong CPU Rev %d (Must be 2)\n",
__func__, ti_cpu_rev(ti_manuf_desc));
kfree(ti_manuf_desc);
goto stayinbootmode;
}
kfree(ti_manuf_desc);
/*
* In order to update the I2C firmware we must change the type
* 2 record to type 0xF2. This will force the UMP to come up
* in Boot Mode. Then while in boot mode, the driver will
* download the latest firmware (padded to 15.5k) into the
* UMP ram. Finally when the device comes back up in download
* mode the driver will cause the new firmware to be copied
* from the UMP Ram to I2C and the firmware will update the
* record type from 0xf2 to 0x02.
*
* Do we really have to copy the whole firmware image,
* or could we do this in place!
*/
/* Allocate a 15.5k buffer + 3 byte header */
buffer_size = (((1024 * 16) - 512) +
sizeof(struct ti_i2c_image_header));
buffer = kmalloc(buffer_size, GFP_KERNEL);
if (!buffer)
return -ENOMEM;
/* Initialize the buffer to 0xff (pad the buffer) */
memset(buffer, 0xff, buffer_size);
memcpy(buffer, &fw->data[4], fw->size - 4);
for (i = sizeof(struct ti_i2c_image_header);
i < buffer_size; i++) {
cs = (__u8)(cs + buffer[i]);
}
header = (struct ti_i2c_image_header *)buffer;
/* update length and checksum after padding */
header->Length = cpu_to_le16((__u16)(buffer_size -
sizeof(struct ti_i2c_image_header)));
header->CheckSum = cs;
/* Download the operational code */
dev_dbg(dev, "%s - Downloading operational code image version %d.%d (TI UMP)\n",
__func__,
fw_hdr->major_version, fw_hdr->minor_version);
status = download_code(serial, buffer, buffer_size);
kfree(buffer);
if (status) {
dev_dbg(dev, "%s - Error downloading operational code image\n", __func__);
return status;
}
/* Device will reboot */
serial->product_info.TiMode = TI_MODE_TRANSITIONING;
dev_dbg(dev, "%s - Download successful -- Device rebooting...\n", __func__);
return 1;
}
stayinbootmode:
/* Eprom is invalid or blank stay in boot mode */
dev_dbg(dev, "%s - STAYING IN BOOT MODE\n", __func__);
serial->product_info.TiMode = TI_MODE_BOOT;
return 1;
}
static int ti_do_config(struct edgeport_port *port, int feature, int on)
{
int port_number = port->port->port_number;
on = !!on; /* 1 or 0 not bitmask */
return send_cmd(port->port->serial->dev,
feature, (__u8)(UMPM_UART1_PORT + port_number),
on, NULL, 0);
}
static int restore_mcr(struct edgeport_port *port, __u8 mcr)
{
int status = 0;
dev_dbg(&port->port->dev, "%s - %x\n", __func__, mcr);
status = ti_do_config(port, UMPC_SET_CLR_DTR, mcr & MCR_DTR);
if (status)
return status;
status = ti_do_config(port, UMPC_SET_CLR_RTS, mcr & MCR_RTS);
if (status)
return status;
return ti_do_config(port, UMPC_SET_CLR_LOOPBACK, mcr & MCR_LOOPBACK);
}
/* Convert TI LSR to standard UART flags */
static __u8 map_line_status(__u8 ti_lsr)
{
__u8 lsr = 0;
#define MAP_FLAG(flagUmp, flagUart) \
if (ti_lsr & flagUmp) \
lsr |= flagUart;
MAP_FLAG(UMP_UART_LSR_OV_MASK, LSR_OVER_ERR) /* overrun */
MAP_FLAG(UMP_UART_LSR_PE_MASK, LSR_PAR_ERR) /* parity error */
MAP_FLAG(UMP_UART_LSR_FE_MASK, LSR_FRM_ERR) /* framing error */
MAP_FLAG(UMP_UART_LSR_BR_MASK, LSR_BREAK) /* break detected */
MAP_FLAG(UMP_UART_LSR_RX_MASK, LSR_RX_AVAIL) /* rx data available */
MAP_FLAG(UMP_UART_LSR_TX_MASK, LSR_TX_EMPTY) /* tx hold reg empty */
#undef MAP_FLAG
return lsr;
}
static void handle_new_msr(struct edgeport_port *edge_port, __u8 msr)
{
struct async_icount *icount;
struct tty_struct *tty;
dev_dbg(&edge_port->port->dev, "%s - %02x\n", __func__, msr);
if (msr & (EDGEPORT_MSR_DELTA_CTS | EDGEPORT_MSR_DELTA_DSR |
EDGEPORT_MSR_DELTA_RI | EDGEPORT_MSR_DELTA_CD)) {
icount = &edge_port->port->icount;
/* update input line counters */
if (msr & EDGEPORT_MSR_DELTA_CTS)
icount->cts++;
if (msr & EDGEPORT_MSR_DELTA_DSR)
icount->dsr++;
if (msr & EDGEPORT_MSR_DELTA_CD)
icount->dcd++;
if (msr & EDGEPORT_MSR_DELTA_RI)
icount->rng++;
wake_up_interruptible(&edge_port->port->port.delta_msr_wait);
}
/* Save the new modem status */
edge_port->shadow_msr = msr & 0xf0;
tty = tty_port_tty_get(&edge_port->port->port);
/* handle CTS flow control */
if (tty && C_CRTSCTS(tty)) {
if (msr & EDGEPORT_MSR_CTS)
tty_wakeup(tty);
}
tty_kref_put(tty);
}
static void handle_new_lsr(struct edgeport_port *edge_port, int lsr_data,
__u8 lsr, __u8 data)
{
struct async_icount *icount;
__u8 new_lsr = (__u8)(lsr & (__u8)(LSR_OVER_ERR | LSR_PAR_ERR |
LSR_FRM_ERR | LSR_BREAK));
dev_dbg(&edge_port->port->dev, "%s - %02x\n", __func__, new_lsr);
edge_port->shadow_lsr = lsr;
if (new_lsr & LSR_BREAK)
/*
* Parity and Framing errors only count if they
* occur exclusive of a break being received.
*/
new_lsr &= (__u8)(LSR_OVER_ERR | LSR_BREAK);
/* Place LSR data byte into Rx buffer */
if (lsr_data)
edge_tty_recv(edge_port->port, &data, 1);
/* update input line counters */
icount = &edge_port->port->icount;
if (new_lsr & LSR_BREAK)
icount->brk++;
if (new_lsr & LSR_OVER_ERR)
icount->overrun++;
if (new_lsr & LSR_PAR_ERR)
icount->parity++;
if (new_lsr & LSR_FRM_ERR)
icount->frame++;
}
static void edge_interrupt_callback(struct urb *urb)
{
struct edgeport_serial *edge_serial = urb->context;
struct usb_serial_port *port;
struct edgeport_port *edge_port;
struct device *dev;
unsigned char *data = urb->transfer_buffer;
int length = urb->actual_length;
int port_number;
int function;
int retval;
__u8 lsr;
__u8 msr;
int status = urb->status;
switch (status) {
case 0:
/* success */
break;
case -ECONNRESET:
case -ENOENT:
case -ESHUTDOWN:
/* this urb is terminated, clean up */
dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d\n",
__func__, status);
return;
default:
dev_err(&urb->dev->dev, "%s - nonzero urb status received: "
"%d\n", __func__, status);
goto exit;
}
if (!length) {
dev_dbg(&urb->dev->dev, "%s - no data in urb\n", __func__);
goto exit;
}
dev = &edge_serial->serial->dev->dev;
usb_serial_debug_data(dev, __func__, length, data);
if (length != 2) {
dev_dbg(dev, "%s - expecting packet of size 2, got %d\n", __func__, length);
goto exit;
}
port_number = TIUMP_GET_PORT_FROM_CODE(data[0]);
function = TIUMP_GET_FUNC_FROM_CODE(data[0]);
dev_dbg(dev, "%s - port_number %d, function %d, info 0x%x\n", __func__,
port_number, function, data[1]);
if (port_number >= edge_serial->serial->num_ports) {
dev_err(dev, "bad port number %d\n", port_number);
goto exit;
}
port = edge_serial->serial->port[port_number];
edge_port = usb_get_serial_port_data(port);
if (!edge_port) {
dev_dbg(dev, "%s - edge_port not found\n", __func__);
return;
}
switch (function) {
case TIUMP_INTERRUPT_CODE_LSR:
lsr = map_line_status(data[1]);
if (lsr & UMP_UART_LSR_DATA_MASK) {
/*
* Save the LSR event for bulk read completion routine
*/
dev_dbg(dev, "%s - LSR Event Port %u LSR Status = %02x\n",
__func__, port_number, lsr);
edge_port->lsr_event = 1;
edge_port->lsr_mask = lsr;
} else {
dev_dbg(dev, "%s - ===== Port %d LSR Status = %02x ======\n",
__func__, port_number, lsr);
handle_new_lsr(edge_port, 0, lsr, 0);
}
break;
case TIUMP_INTERRUPT_CODE_MSR: /* MSR */
/* Copy MSR from UMP */
msr = data[1];
dev_dbg(dev, "%s - ===== Port %u MSR Status = %02x ======\n",
__func__, port_number, msr);
handle_new_msr(edge_port, msr);
break;
default:
dev_err(&urb->dev->dev,
"%s - Unknown Interrupt code from UMP %x\n",
__func__, data[1]);
break;
}
exit:
retval = usb_submit_urb(urb, GFP_ATOMIC);
if (retval)
dev_err(&urb->dev->dev,
"%s - usb_submit_urb failed with result %d\n",
__func__, retval);
}
static void edge_bulk_in_callback(struct urb *urb)
{
struct edgeport_port *edge_port = urb->context;
struct device *dev = &edge_port->port->dev;
unsigned char *data = urb->transfer_buffer;
int retval = 0;
int port_number;
int status = urb->status;
switch (status) {
case 0:
/* success */
break;
case -ECONNRESET:
case -ENOENT:
case -ESHUTDOWN:
/* this urb is terminated, clean up */
dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d\n", __func__, status);
return;
default:
dev_err(&urb->dev->dev, "%s - nonzero read bulk status received: %d\n", __func__, status);
}
if (status == -EPIPE)
goto exit;
if (status) {
dev_err(&urb->dev->dev, "%s - stopping read!\n", __func__);
return;
}
port_number = edge_port->port->port_number;
if (urb->actual_length > 0 && edge_port->lsr_event) {
edge_port->lsr_event = 0;
dev_dbg(dev, "%s ===== Port %u LSR Status = %02x, Data = %02x ======\n",
__func__, port_number, edge_port->lsr_mask, *data);
handle_new_lsr(edge_port, 1, edge_port->lsr_mask, *data);
/* Adjust buffer length/pointer */
--urb->actual_length;
++data;
}
if (urb->actual_length) {
usb_serial_debug_data(dev, __func__, urb->actual_length, data);
if (edge_port->close_pending)
dev_dbg(dev, "%s - close pending, dropping data on the floor\n",
__func__);
else
edge_tty_recv(edge_port->port, data,
urb->actual_length);
edge_port->port->icount.rx += urb->actual_length;
}
exit:
/* continue read unless stopped */
spin_lock(&edge_port->ep_lock);
if (edge_port->ep_read_urb_state == EDGE_READ_URB_RUNNING)
retval = usb_submit_urb(urb, GFP_ATOMIC);
else if (edge_port->ep_read_urb_state == EDGE_READ_URB_STOPPING)
edge_port->ep_read_urb_state = EDGE_READ_URB_STOPPED;
spin_unlock(&edge_port->ep_lock);
if (retval)
dev_err(dev, "%s - usb_submit_urb failed with result %d\n", __func__, retval);
}
static void edge_tty_recv(struct usb_serial_port *port, unsigned char *data,
int length)
{
int queued;
queued = tty_insert_flip_string(&port->port, data, length);
if (queued < length)
dev_err(&port->dev, "%s - dropping data, %d bytes lost\n",
__func__, length - queued);
tty_flip_buffer_push(&port->port);
}
static void edge_bulk_out_callback(struct urb *urb)
{
struct usb_serial_port *port = urb->context;
struct edgeport_port *edge_port = usb_get_serial_port_data(port);
int status = urb->status;
struct tty_struct *tty;
edge_port->ep_write_urb_in_use = 0;
switch (status) {
case 0:
/* success */
break;
case -ECONNRESET:
case -ENOENT:
case -ESHUTDOWN:
/* this urb is terminated, clean up */
dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d\n",
__func__, status);
return;
default:
dev_err_console(port, "%s - nonzero write bulk status "
"received: %d\n", __func__, status);
}
/* send any buffered data */
tty = tty_port_tty_get(&port->port);
edge_send(port, tty);
tty_kref_put(tty);
}
static int edge_open(struct tty_struct *tty, struct usb_serial_port *port)
{
struct edgeport_port *edge_port = usb_get_serial_port_data(port);
struct edgeport_serial *edge_serial;
struct usb_device *dev;
struct urb *urb;
int port_number;
int status;
u16 open_settings;
u8 transaction_timeout;
if (edge_port == NULL)
return -ENODEV;
port_number = port->port_number;
dev = port->serial->dev;
/* turn off loopback */
status = ti_do_config(edge_port, UMPC_SET_CLR_LOOPBACK, 0);
if (status) {
dev_err(&port->dev,
"%s - cannot send clear loopback command, %d\n",
__func__, status);
return status;
}
/* set up the port settings */
if (tty)
edge_set_termios(tty, port, &tty->termios);
/* open up the port */
/* milliseconds to timeout for DMA transfer */
transaction_timeout = 2;
edge_port->ump_read_timeout =
max(20, ((transaction_timeout * 3) / 2));
/* milliseconds to timeout for DMA transfer */
open_settings = (u8)(UMP_DMA_MODE_CONTINOUS |
UMP_PIPE_TRANS_TIMEOUT_ENA |
(transaction_timeout << 2));
dev_dbg(&port->dev, "%s - Sending UMPC_OPEN_PORT\n", __func__);
/* Tell TI to open and start the port */
status = send_cmd(dev, UMPC_OPEN_PORT,
(u8)(UMPM_UART1_PORT + port_number), open_settings, NULL, 0);
if (status) {
dev_err(&port->dev, "%s - cannot send open command, %d\n",
__func__, status);
return status;
}
/* Start the DMA? */
status = send_cmd(dev, UMPC_START_PORT,
(u8)(UMPM_UART1_PORT + port_number), 0, NULL, 0);
if (status) {
dev_err(&port->dev, "%s - cannot send start DMA command, %d\n",
__func__, status);
return status;
}
/* Clear TX and RX buffers in UMP */
status = purge_port(port, UMP_PORT_DIR_OUT | UMP_PORT_DIR_IN);
if (status) {
dev_err(&port->dev,
"%s - cannot send clear buffers command, %d\n",
__func__, status);
return status;
}
/* Read Initial MSR */
status = ti_vread_sync(dev, UMPC_READ_MSR, 0,
(__u16)(UMPM_UART1_PORT + port_number),
&edge_port->shadow_msr, 1);
if (status) {
dev_err(&port->dev, "%s - cannot send read MSR command, %d\n",
__func__, status);
return status;
}
dev_dbg(&port->dev, "ShadowMSR 0x%X\n", edge_port->shadow_msr);
/* Set Initial MCR */
edge_port->shadow_mcr = MCR_RTS | MCR_DTR;
dev_dbg(&port->dev, "ShadowMCR 0x%X\n", edge_port->shadow_mcr);
edge_serial = edge_port->edge_serial;
if (mutex_lock_interruptible(&edge_serial->es_lock))
return -ERESTARTSYS;
if (edge_serial->num_ports_open == 0) {
/* we are the first port to open, post the interrupt urb */
urb = edge_serial->serial->port[0]->interrupt_in_urb;
urb->context = edge_serial;
status = usb_submit_urb(urb, GFP_KERNEL);
if (status) {
dev_err(&port->dev,
"%s - usb_submit_urb failed with value %d\n",
__func__, status);
goto release_es_lock;
}
}
/*
* reset the data toggle on the bulk endpoints to work around bug in
* host controllers where things get out of sync some times
*/
usb_clear_halt(dev, port->write_urb->pipe);
usb_clear_halt(dev, port->read_urb->pipe);
/* start up our bulk read urb */
urb = port->read_urb;
edge_port->ep_read_urb_state = EDGE_READ_URB_RUNNING;
urb->context = edge_port;
status = usb_submit_urb(urb, GFP_KERNEL);
if (status) {
dev_err(&port->dev,
"%s - read bulk usb_submit_urb failed with value %d\n",
__func__, status);
goto unlink_int_urb;
}
++edge_serial->num_ports_open;
goto release_es_lock;
unlink_int_urb:
if (edge_port->edge_serial->num_ports_open == 0)
usb_kill_urb(port->serial->port[0]->interrupt_in_urb);
release_es_lock:
mutex_unlock(&edge_serial->es_lock);
return status;
}
static void edge_close(struct usb_serial_port *port)
{
struct edgeport_serial *edge_serial;
struct edgeport_port *edge_port;
struct usb_serial *serial = port->serial;
unsigned long flags;
int port_number;
edge_serial = usb_get_serial_data(port->serial);
edge_port = usb_get_serial_port_data(port);
if (edge_serial == NULL || edge_port == NULL)
return;
/*
* The bulkreadcompletion routine will check
* this flag and dump add read data
*/
edge_port->close_pending = 1;
usb_kill_urb(port->read_urb);
usb_kill_urb(port->write_urb);
edge_port->ep_write_urb_in_use = 0;
spin_lock_irqsave(&edge_port->ep_lock, flags);
kfifo_reset_out(&port->write_fifo);
spin_unlock_irqrestore(&edge_port->ep_lock, flags);
dev_dbg(&port->dev, "%s - send umpc_close_port\n", __func__);
port_number = port->port_number;
send_cmd(serial->dev, UMPC_CLOSE_PORT,
(__u8)(UMPM_UART1_PORT + port_number), 0, NULL, 0);
mutex_lock(&edge_serial->es_lock);
--edge_port->edge_serial->num_ports_open;
if (edge_port->edge_serial->num_ports_open <= 0) {
/* last port is now closed, let's shut down our interrupt urb */
usb_kill_urb(port->serial->port[0]->interrupt_in_urb);
edge_port->edge_serial->num_ports_open = 0;
}
mutex_unlock(&edge_serial->es_lock);
edge_port->close_pending = 0;
}
static int edge_write(struct tty_struct *tty, struct usb_serial_port *port,
const unsigned char *data, int count)
{
struct edgeport_port *edge_port = usb_get_serial_port_data(port);
if (count == 0) {
dev_dbg(&port->dev, "%s - write request of 0 bytes\n", __func__);
return 0;
}
if (edge_port == NULL)
return -ENODEV;
if (edge_port->close_pending == 1)
return -ENODEV;
count = kfifo_in_locked(&port->write_fifo, data, count,
&edge_port->ep_lock);
edge_send(port, tty);
return count;
}
static void edge_send(struct usb_serial_port *port, struct tty_struct *tty)
{
int count, result;
struct edgeport_port *edge_port = usb_get_serial_port_data(port);
unsigned long flags;
spin_lock_irqsave(&edge_port->ep_lock, flags);
if (edge_port->ep_write_urb_in_use) {
spin_unlock_irqrestore(&edge_port->ep_lock, flags);
return;
}
count = kfifo_out(&port->write_fifo,
port->write_urb->transfer_buffer,
port->bulk_out_size);
if (count == 0) {
spin_unlock_irqrestore(&edge_port->ep_lock, flags);
return;
}
edge_port->ep_write_urb_in_use = 1;
spin_unlock_irqrestore(&edge_port->ep_lock, flags);
usb_serial_debug_data(&port->dev, __func__, count, port->write_urb->transfer_buffer);
/* set up our urb */
port->write_urb->transfer_buffer_length = count;
/* send the data out the bulk port */
result = usb_submit_urb(port->write_urb, GFP_ATOMIC);
if (result) {
dev_err_console(port,
"%s - failed submitting write urb, error %d\n",
__func__, result);
edge_port->ep_write_urb_in_use = 0;
/* TODO: reschedule edge_send */
} else
edge_port->port->icount.tx += count;
/*
* wakeup any process waiting for writes to complete
* there is now more room in the buffer for new writes
*/
if (tty)
tty_wakeup(tty);
}
static int edge_write_room(struct tty_struct *tty)
{
struct usb_serial_port *port = tty->driver_data;
struct edgeport_port *edge_port = usb_get_serial_port_data(port);
int room = 0;
unsigned long flags;
if (edge_port == NULL)
return 0;
if (edge_port->close_pending == 1)
return 0;
spin_lock_irqsave(&edge_port->ep_lock, flags);
room = kfifo_avail(&port->write_fifo);
spin_unlock_irqrestore(&edge_port->ep_lock, flags);
dev_dbg(&port->dev, "%s - returns %d\n", __func__, room);
return room;
}
static int edge_chars_in_buffer(struct tty_struct *tty)
{
struct usb_serial_port *port = tty->driver_data;
struct edgeport_port *edge_port = usb_get_serial_port_data(port);
int chars = 0;
unsigned long flags;
if (edge_port == NULL)
return 0;
spin_lock_irqsave(&edge_port->ep_lock, flags);
chars = kfifo_len(&port->write_fifo);
spin_unlock_irqrestore(&edge_port->ep_lock, flags);
dev_dbg(&port->dev, "%s - returns %d\n", __func__, chars);
return chars;
}
static bool edge_tx_empty(struct usb_serial_port *port)
{
struct edgeport_port *edge_port = usb_get_serial_port_data(port);
int ret;
ret = tx_active(edge_port);
if (ret > 0)
return false;
return true;
}
static void edge_throttle(struct tty_struct *tty)
{
struct usb_serial_port *port = tty->driver_data;
struct edgeport_port *edge_port = usb_get_serial_port_data(port);
int status;
if (edge_port == NULL)
return;
/* if we are implementing XON/XOFF, send the stop character */
if (I_IXOFF(tty)) {
unsigned char stop_char = STOP_CHAR(tty);
status = edge_write(tty, port, &stop_char, 1);
if (status <= 0) {
dev_err(&port->dev, "%s - failed to write stop character, %d\n", __func__, status);
}
}
/*
* if we are implementing RTS/CTS, stop reads
* and the Edgeport will clear the RTS line
*/
if (C_CRTSCTS(tty))
stop_read(edge_port);
}
static void edge_unthrottle(struct tty_struct *tty)
{
struct usb_serial_port *port = tty->driver_data;
struct edgeport_port *edge_port = usb_get_serial_port_data(port);
int status;
if (edge_port == NULL)
return;
/* if we are implementing XON/XOFF, send the start character */
if (I_IXOFF(tty)) {
unsigned char start_char = START_CHAR(tty);
status = edge_write(tty, port, &start_char, 1);
if (status <= 0) {
dev_err(&port->dev, "%s - failed to write start character, %d\n", __func__, status);
}
}
/*
* if we are implementing RTS/CTS, restart reads
* are the Edgeport will assert the RTS line
*/
if (C_CRTSCTS(tty)) {
status = restart_read(edge_port);
if (status)
dev_err(&port->dev,
"%s - read bulk usb_submit_urb failed: %d\n",
__func__, status);
}
}
static void stop_read(struct edgeport_port *edge_port)
{
unsigned long flags;
spin_lock_irqsave(&edge_port->ep_lock, flags);
if (edge_port->ep_read_urb_state == EDGE_READ_URB_RUNNING)
edge_port->ep_read_urb_state = EDGE_READ_URB_STOPPING;
edge_port->shadow_mcr &= ~MCR_RTS;
spin_unlock_irqrestore(&edge_port->ep_lock, flags);
}
static int restart_read(struct edgeport_port *edge_port)
{
struct urb *urb;
int status = 0;
unsigned long flags;
spin_lock_irqsave(&edge_port->ep_lock, flags);
if (edge_port->ep_read_urb_state == EDGE_READ_URB_STOPPED) {
urb = edge_port->port->read_urb;
status = usb_submit_urb(urb, GFP_ATOMIC);
}
edge_port->ep_read_urb_state = EDGE_READ_URB_RUNNING;
edge_port->shadow_mcr |= MCR_RTS;
spin_unlock_irqrestore(&edge_port->ep_lock, flags);
return status;
}
static void change_port_settings(struct tty_struct *tty,
struct edgeport_port *edge_port, struct ktermios *old_termios)
{
struct device *dev = &edge_port->port->dev;
struct ump_uart_config *config;
int baud;
unsigned cflag;
int status;
int port_number = edge_port->port->port_number;
config = kmalloc (sizeof (*config), GFP_KERNEL);
if (!config) {
tty->termios = *old_termios;
return;
}
cflag = tty->termios.c_cflag;
config->wFlags = 0;
/* These flags must be set */
config->wFlags |= UMP_MASK_UART_FLAGS_RECEIVE_MS_INT;
config->wFlags |= UMP_MASK_UART_FLAGS_AUTO_START_ON_ERR;
config->bUartMode = (__u8)(edge_port->bUartMode);
switch (cflag & CSIZE) {
case CS5:
config->bDataBits = UMP_UART_CHAR5BITS;
dev_dbg(dev, "%s - data bits = 5\n", __func__);
break;
case CS6:
config->bDataBits = UMP_UART_CHAR6BITS;
dev_dbg(dev, "%s - data bits = 6\n", __func__);
break;
case CS7:
config->bDataBits = UMP_UART_CHAR7BITS;
dev_dbg(dev, "%s - data bits = 7\n", __func__);
break;
default:
case CS8:
config->bDataBits = UMP_UART_CHAR8BITS;
dev_dbg(dev, "%s - data bits = 8\n", __func__);
break;
}
if (cflag & PARENB) {
if (cflag & PARODD) {
config->wFlags |= UMP_MASK_UART_FLAGS_PARITY;
config->bParity = UMP_UART_ODDPARITY;
dev_dbg(dev, "%s - parity = odd\n", __func__);
} else {
config->wFlags |= UMP_MASK_UART_FLAGS_PARITY;
config->bParity = UMP_UART_EVENPARITY;
dev_dbg(dev, "%s - parity = even\n", __func__);
}
} else {
config->bParity = UMP_UART_NOPARITY;
dev_dbg(dev, "%s - parity = none\n", __func__);
}
if (cflag & CSTOPB) {
config->bStopBits = UMP_UART_STOPBIT2;
dev_dbg(dev, "%s - stop bits = 2\n", __func__);
} else {
config->bStopBits = UMP_UART_STOPBIT1;
dev_dbg(dev, "%s - stop bits = 1\n", __func__);
}
/* figure out the flow control settings */
if (cflag & CRTSCTS) {
config->wFlags |= UMP_MASK_UART_FLAGS_OUT_X_CTS_FLOW;
config->wFlags |= UMP_MASK_UART_FLAGS_RTS_FLOW;
dev_dbg(dev, "%s - RTS/CTS is enabled\n", __func__);
} else {
dev_dbg(dev, "%s - RTS/CTS is disabled\n", __func__);
restart_read(edge_port);
}
/*
* if we are implementing XON/XOFF, set the start and stop
* character in the device
*/
config->cXon = START_CHAR(tty);
config->cXoff = STOP_CHAR(tty);
/* if we are implementing INBOUND XON/XOFF */
if (I_IXOFF(tty)) {
config->wFlags |= UMP_MASK_UART_FLAGS_IN_X;
dev_dbg(dev, "%s - INBOUND XON/XOFF is enabled, XON = %2x, XOFF = %2x\n",
__func__, config->cXon, config->cXoff);
} else
dev_dbg(dev, "%s - INBOUND XON/XOFF is disabled\n", __func__);
/* if we are implementing OUTBOUND XON/XOFF */
if (I_IXON(tty)) {
config->wFlags |= UMP_MASK_UART_FLAGS_OUT_X;
dev_dbg(dev, "%s - OUTBOUND XON/XOFF is enabled, XON = %2x, XOFF = %2x\n",
__func__, config->cXon, config->cXoff);
} else
dev_dbg(dev, "%s - OUTBOUND XON/XOFF is disabled\n", __func__);
tty->termios.c_cflag &= ~CMSPAR;
/* Round the baud rate */
baud = tty_get_baud_rate(tty);
if (!baud) {
/* pick a default, any default... */
baud = 9600;
} else {
/* Avoid a zero divisor. */
baud = min(baud, 461550);
tty_encode_baud_rate(tty, baud, baud);
}
edge_port->baud_rate = baud;
config->wBaudRate = (__u16)((461550L + baud/2) / baud);
/* FIXME: Recompute actual baud from divisor here */
dev_dbg(dev, "%s - baud rate = %d, wBaudRate = %d\n", __func__, baud, config->wBaudRate);
dev_dbg(dev, "wBaudRate: %d\n", (int)(461550L / config->wBaudRate));
dev_dbg(dev, "wFlags: 0x%x\n", config->wFlags);
dev_dbg(dev, "bDataBits: %d\n", config->bDataBits);
dev_dbg(dev, "bParity: %d\n", config->bParity);
dev_dbg(dev, "bStopBits: %d\n", config->bStopBits);
dev_dbg(dev, "cXon: %d\n", config->cXon);
dev_dbg(dev, "cXoff: %d\n", config->cXoff);
dev_dbg(dev, "bUartMode: %d\n", config->bUartMode);
/* move the word values into big endian mode */
cpu_to_be16s(&config->wFlags);
cpu_to_be16s(&config->wBaudRate);
status = send_cmd(edge_port->port->serial->dev, UMPC_SET_CONFIG,
(__u8)(UMPM_UART1_PORT + port_number),
0, (__u8 *)config, sizeof(*config));
if (status)
dev_dbg(dev, "%s - error %d when trying to write config to device\n",
__func__, status);
kfree(config);
}
static void edge_set_termios(struct tty_struct *tty,
struct usb_serial_port *port, struct ktermios *old_termios)
{
struct edgeport_port *edge_port = usb_get_serial_port_data(port);
if (edge_port == NULL)
return;
/* change the port settings to the new ones specified */
change_port_settings(tty, edge_port, old_termios);
}
static int edge_tiocmset(struct tty_struct *tty,
unsigned int set, unsigned int clear)
{
struct usb_serial_port *port = tty->driver_data;
struct edgeport_port *edge_port = usb_get_serial_port_data(port);
unsigned int mcr;
unsigned long flags;
spin_lock_irqsave(&edge_port->ep_lock, flags);
mcr = edge_port->shadow_mcr;
if (set & TIOCM_RTS)
mcr |= MCR_RTS;
if (set & TIOCM_DTR)
mcr |= MCR_DTR;
if (set & TIOCM_LOOP)
mcr |= MCR_LOOPBACK;
if (clear & TIOCM_RTS)
mcr &= ~MCR_RTS;
if (clear & TIOCM_DTR)
mcr &= ~MCR_DTR;
if (clear & TIOCM_LOOP)
mcr &= ~MCR_LOOPBACK;
edge_port->shadow_mcr = mcr;
spin_unlock_irqrestore(&edge_port->ep_lock, flags);
restore_mcr(edge_port, mcr);
return 0;
}
static int edge_tiocmget(struct tty_struct *tty)
{
struct usb_serial_port *port = tty->driver_data;
struct edgeport_port *edge_port = usb_get_serial_port_data(port);
unsigned int result = 0;
unsigned int msr;
unsigned int mcr;
unsigned long flags;
spin_lock_irqsave(&edge_port->ep_lock, flags);
msr = edge_port->shadow_msr;
mcr = edge_port->shadow_mcr;
result = ((mcr & MCR_DTR) ? TIOCM_DTR: 0) /* 0x002 */
| ((mcr & MCR_RTS) ? TIOCM_RTS: 0) /* 0x004 */
| ((msr & EDGEPORT_MSR_CTS) ? TIOCM_CTS: 0) /* 0x020 */
| ((msr & EDGEPORT_MSR_CD) ? TIOCM_CAR: 0) /* 0x040 */
| ((msr & EDGEPORT_MSR_RI) ? TIOCM_RI: 0) /* 0x080 */
| ((msr & EDGEPORT_MSR_DSR) ? TIOCM_DSR: 0); /* 0x100 */
dev_dbg(&port->dev, "%s -- %x\n", __func__, result);
spin_unlock_irqrestore(&edge_port->ep_lock, flags);
return result;
}
static int get_serial_info(struct edgeport_port *edge_port,
struct serial_struct __user *retinfo)
{
struct serial_struct tmp;
unsigned cwait;
cwait = edge_port->port->port.closing_wait;
if (cwait != ASYNC_CLOSING_WAIT_NONE)
cwait = jiffies_to_msecs(cwait) / 10;
memset(&tmp, 0, sizeof(tmp));
tmp.type = PORT_16550A;
tmp.line = edge_port->port->minor;
tmp.port = edge_port->port->port_number;
tmp.irq = 0;
tmp.xmit_fifo_size = edge_port->port->bulk_out_size;
tmp.baud_base = 9600;
tmp.close_delay = 5*HZ;
tmp.closing_wait = cwait;
if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
return -EFAULT;
return 0;
}
static int edge_ioctl(struct tty_struct *tty,
unsigned int cmd, unsigned long arg)
{
struct usb_serial_port *port = tty->driver_data;
struct edgeport_port *edge_port = usb_get_serial_port_data(port);
switch (cmd) {
case TIOCGSERIAL:
dev_dbg(&port->dev, "%s - TIOCGSERIAL\n", __func__);
return get_serial_info(edge_port,
(struct serial_struct __user *) arg);
}
return -ENOIOCTLCMD;
}
static void edge_break(struct tty_struct *tty, int break_state)
{
struct usb_serial_port *port = tty->driver_data;
struct edgeport_port *edge_port = usb_get_serial_port_data(port);
int status;
int bv = 0; /* Off */
if (break_state == -1)
bv = 1; /* On */
status = ti_do_config(edge_port, UMPC_SET_CLR_BREAK, bv);
if (status)
dev_dbg(&port->dev, "%s - error %d sending break set/clear command.\n",
__func__, status);
}
static void edge_heartbeat_schedule(struct edgeport_serial *edge_serial)
{
if (!edge_serial->use_heartbeat)
return;
schedule_delayed_work(&edge_serial->heartbeat_work,
FW_HEARTBEAT_SECS * HZ);
}
static void edge_heartbeat_work(struct work_struct *work)
{
struct edgeport_serial *serial;
struct ti_i2c_desc *rom_desc;
serial = container_of(work, struct edgeport_serial,
heartbeat_work.work);
rom_desc = kmalloc(sizeof(*rom_desc), GFP_KERNEL);
/* Descriptor address request is enough to reset the firmware timer */
if (!rom_desc || !get_descriptor_addr(serial, I2C_DESC_TYPE_ION,
rom_desc)) {
dev_err(&serial->serial->interface->dev,
"%s - Incomplete heartbeat\n", __func__);
}
kfree(rom_desc);
edge_heartbeat_schedule(serial);
}
static int edge_calc_num_ports(struct usb_serial *serial,
struct usb_serial_endpoints *epds)
{
struct device *dev = &serial->interface->dev;
unsigned char num_ports = serial->type->num_ports;
/* Make sure we have the required endpoints when in download mode. */
if (serial->interface->cur_altsetting->desc.bNumEndpoints > 1) {
if (epds->num_bulk_in < num_ports ||
epds->num_bulk_out < num_ports ||
epds->num_interrupt_in < 1) {
dev_err(dev, "required endpoints missing\n");
return -ENODEV;
}
}
return num_ports;
}
static int edge_startup(struct usb_serial *serial)
{
struct edgeport_serial *edge_serial;
int status;
u16 product_id;
/* create our private serial structure */
edge_serial = kzalloc(sizeof(struct edgeport_serial), GFP_KERNEL);
if (!edge_serial)
return -ENOMEM;
mutex_init(&edge_serial->es_lock);
edge_serial->serial = serial;
INIT_DELAYED_WORK(&edge_serial->heartbeat_work, edge_heartbeat_work);
usb_set_serial_data(serial, edge_serial);
status = download_fw(edge_serial);
if (status < 0) {
kfree(edge_serial);
return status;
}
if (status > 0)
return 1; /* bind but do not register any ports */
product_id = le16_to_cpu(
edge_serial->serial->dev->descriptor.idProduct);
/* Currently only the EP/416 models require heartbeat support */
if (edge_serial->fw_version > FW_HEARTBEAT_VERSION_CUTOFF) {
if (product_id == ION_DEVICE_ID_TI_EDGEPORT_416 ||
product_id == ION_DEVICE_ID_TI_EDGEPORT_416B) {
edge_serial->use_heartbeat = true;
}
}
edge_heartbeat_schedule(edge_serial);
return 0;
}
static void edge_disconnect(struct usb_serial *serial)
{
struct edgeport_serial *edge_serial = usb_get_serial_data(serial);
cancel_delayed_work_sync(&edge_serial->heartbeat_work);
}
static void edge_release(struct usb_serial *serial)
{
struct edgeport_serial *edge_serial = usb_get_serial_data(serial);
cancel_delayed_work_sync(&edge_serial->heartbeat_work);
kfree(edge_serial);
}
static int edge_port_probe(struct usb_serial_port *port)
{
struct edgeport_port *edge_port;
int ret;
edge_port = kzalloc(sizeof(*edge_port), GFP_KERNEL);
if (!edge_port)
return -ENOMEM;
spin_lock_init(&edge_port->ep_lock);
edge_port->port = port;
edge_port->edge_serial = usb_get_serial_data(port->serial);
edge_port->bUartMode = default_uart_mode;
switch (port->port_number) {
case 0:
edge_port->uart_base = UMPMEM_BASE_UART1;
edge_port->dma_address = UMPD_OEDB1_ADDRESS;
break;
case 1:
edge_port->uart_base = UMPMEM_BASE_UART2;
edge_port->dma_address = UMPD_OEDB2_ADDRESS;
break;
default:
dev_err(&port->dev, "unknown port number\n");
ret = -ENODEV;
goto err;
}
dev_dbg(&port->dev,
"%s - port_number = %d, uart_base = %04x, dma_address = %04x\n",
__func__, port->port_number, edge_port->uart_base,
edge_port->dma_address);
usb_set_serial_port_data(port, edge_port);
ret = edge_create_sysfs_attrs(port);
if (ret)
goto err;
port->port.closing_wait = msecs_to_jiffies(closing_wait * 10);
port->port.drain_delay = 1;
return 0;
err:
kfree(edge_port);
return ret;
}
static int edge_port_remove(struct usb_serial_port *port)
{
struct edgeport_port *edge_port;
edge_port = usb_get_serial_port_data(port);
edge_remove_sysfs_attrs(port);
kfree(edge_port);
return 0;
}
/* Sysfs Attributes */
static ssize_t uart_mode_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct usb_serial_port *port = to_usb_serial_port(dev);
struct edgeport_port *edge_port = usb_get_serial_port_data(port);
return sprintf(buf, "%d\n", edge_port->bUartMode);
}
static ssize_t uart_mode_store(struct device *dev,
struct device_attribute *attr, const char *valbuf, size_t count)
{
struct usb_serial_port *port = to_usb_serial_port(dev);
struct edgeport_port *edge_port = usb_get_serial_port_data(port);
unsigned int v = simple_strtoul(valbuf, NULL, 0);
dev_dbg(dev, "%s: setting uart_mode = %d\n", __func__, v);
if (v < 256)
edge_port->bUartMode = v;
else
dev_err(dev, "%s - uart_mode %d is invalid\n", __func__, v);
return count;
}
static DEVICE_ATTR_RW(uart_mode);
static int edge_create_sysfs_attrs(struct usb_serial_port *port)
{
return device_create_file(&port->dev, &dev_attr_uart_mode);
}
static int edge_remove_sysfs_attrs(struct usb_serial_port *port)
{
device_remove_file(&port->dev, &dev_attr_uart_mode);
return 0;
}
#ifdef CONFIG_PM
static int edge_suspend(struct usb_serial *serial, pm_message_t message)
{
struct edgeport_serial *edge_serial = usb_get_serial_data(serial);
cancel_delayed_work_sync(&edge_serial->heartbeat_work);
return 0;
}
static int edge_resume(struct usb_serial *serial)
{
struct edgeport_serial *edge_serial = usb_get_serial_data(serial);
edge_heartbeat_schedule(edge_serial);
return 0;
}
#endif
static struct usb_serial_driver edgeport_1port_device = {
.driver = {
.owner = THIS_MODULE,
.name = "edgeport_ti_1",
},
.description = "Edgeport TI 1 port adapter",
.id_table = edgeport_1port_id_table,
.num_ports = 1,
.num_bulk_out = 1,
.open = edge_open,
.close = edge_close,
.throttle = edge_throttle,
.unthrottle = edge_unthrottle,
.attach = edge_startup,
.calc_num_ports = edge_calc_num_ports,
.disconnect = edge_disconnect,
.release = edge_release,
.port_probe = edge_port_probe,
.port_remove = edge_port_remove,
.ioctl = edge_ioctl,
.set_termios = edge_set_termios,
.tiocmget = edge_tiocmget,
.tiocmset = edge_tiocmset,
.tiocmiwait = usb_serial_generic_tiocmiwait,
.get_icount = usb_serial_generic_get_icount,
.write = edge_write,
.write_room = edge_write_room,
.chars_in_buffer = edge_chars_in_buffer,
.tx_empty = edge_tx_empty,
.break_ctl = edge_break,
.read_int_callback = edge_interrupt_callback,
.read_bulk_callback = edge_bulk_in_callback,
.write_bulk_callback = edge_bulk_out_callback,
#ifdef CONFIG_PM
.suspend = edge_suspend,
.resume = edge_resume,
#endif
};
static struct usb_serial_driver edgeport_2port_device = {
.driver = {
.owner = THIS_MODULE,
.name = "edgeport_ti_2",
},
.description = "Edgeport TI 2 port adapter",
.id_table = edgeport_2port_id_table,
.num_ports = 2,
.num_bulk_out = 1,
.open = edge_open,
.close = edge_close,
.throttle = edge_throttle,
.unthrottle = edge_unthrottle,
.attach = edge_startup,
.calc_num_ports = edge_calc_num_ports,
.disconnect = edge_disconnect,
.release = edge_release,
.port_probe = edge_port_probe,
.port_remove = edge_port_remove,
.ioctl = edge_ioctl,
.set_termios = edge_set_termios,
.tiocmget = edge_tiocmget,
.tiocmset = edge_tiocmset,
.tiocmiwait = usb_serial_generic_tiocmiwait,
.get_icount = usb_serial_generic_get_icount,
.write = edge_write,
.write_room = edge_write_room,
.chars_in_buffer = edge_chars_in_buffer,
.tx_empty = edge_tx_empty,
.break_ctl = edge_break,
.read_int_callback = edge_interrupt_callback,
.read_bulk_callback = edge_bulk_in_callback,
.write_bulk_callback = edge_bulk_out_callback,
#ifdef CONFIG_PM
.suspend = edge_suspend,
.resume = edge_resume,
#endif
};
static struct usb_serial_driver * const serial_drivers[] = {
&edgeport_1port_device, &edgeport_2port_device, NULL
};
module_usb_serial_driver(serial_drivers, id_table_combined);
MODULE_AUTHOR(DRIVER_AUTHOR);
MODULE_DESCRIPTION(DRIVER_DESC);
MODULE_LICENSE("GPL");
MODULE_FIRMWARE("edgeport/down3.bin");
module_param(closing_wait, int, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(closing_wait, "Maximum wait for data to drain, in .01 secs");
module_param(ignore_cpu_rev, bool, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(ignore_cpu_rev,
"Ignore the cpu revision when connecting to a device");
module_param(default_uart_mode, int, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(default_uart_mode, "Default uart_mode, 0=RS232, ...");