mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-29 22:14:41 +08:00
1b283eea62
This fixes a very annoying regression on the Snowball SD card that has been around for a while. It turns out that the device tree does not configure the direction pins properly, nor sets up the pins for the voltage converter properly at boot. Unless all things are correctly set up, the feedback clock will not work, and makes the driver spew messages in the console (but it works, very slowly): root@Ux500:/ mount /dev/mmcblk0p2 /mnt/ [ 9.953460] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer! [ 9.960296] mmcblk0: error -110 sending status command, retrying [ 9.966461] mmcblk0: error -110 sending status command, retrying [ 9.972534] mmcblk0: error -110 sending status command, aborting Fix this by rectifying the device tree to correspond to that of the Ux500 HREF boards plus the DAT31DIR setting that is unique for the Snowball, and things start working smoothly. Add in the SDR12 and SDR25 modes which this host can do without any problems. I don't know if this has ever been correct, sadly. It works after this patch. Cc: stable@vger.kernel.org Reported-by: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
672 lines
16 KiB
Plaintext
672 lines
16 KiB
Plaintext
/*
|
|
* Copyright 2011 ST-Ericsson AB
|
|
*
|
|
* The code contained herein is licensed under the GNU General Public
|
|
* License. You may obtain a copy of the GNU General Public License
|
|
* Version 2 or later at the following locations:
|
|
*
|
|
* http://www.opensource.org/licenses/gpl-license.html
|
|
* http://www.gnu.org/copyleft/gpl.html
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include "ste-dbx5x0.dtsi"
|
|
#include "ste-href-ab8500.dtsi"
|
|
#include "ste-href-family-pinctrl.dtsi"
|
|
|
|
/ {
|
|
model = "Calao Systems Snowball platform with device tree";
|
|
compatible = "calaosystems,snowball-a9500", "st-ericsson,u9500";
|
|
|
|
/* This stablilizes the serial port enumeration */
|
|
aliases {
|
|
serial0 = &ux500_serial0;
|
|
serial1 = &ux500_serial1;
|
|
serial2 = &ux500_serial2;
|
|
};
|
|
|
|
memory {
|
|
reg = <0x00000000 0x20000000>;
|
|
};
|
|
|
|
en_3v3_reg: en_3v3 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "en-3v3-fixed-supply";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
/* AB8500 GPIOs start from 1 - offset 25 is GPIO26. */
|
|
gpio = <&ab8500_gpio 25 0x4>;
|
|
startup-delay-us = <5000>;
|
|
enable-active-high;
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
button@1 {
|
|
debounce_interval = <50>;
|
|
wakeup-source;
|
|
linux,code = <2>;
|
|
label = "userpb";
|
|
gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
button@2 {
|
|
debounce_interval = <50>;
|
|
wakeup-source;
|
|
linux,code = <3>;
|
|
label = "extkb1";
|
|
gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
button@3 {
|
|
debounce_interval = <50>;
|
|
wakeup-source;
|
|
linux,code = <4>;
|
|
label = "extkb2";
|
|
gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
button@4 {
|
|
debounce_interval = <50>;
|
|
wakeup-source;
|
|
linux,code = <5>;
|
|
label = "extkb3";
|
|
gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
button@5 {
|
|
debounce_interval = <50>;
|
|
wakeup-source;
|
|
linux,code = <6>;
|
|
label = "extkb4";
|
|
gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&gpioled_snowball_mode>;
|
|
used-led {
|
|
label = "user_led";
|
|
gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>;
|
|
default-state = "on";
|
|
linux,default-trigger = "heartbeat";
|
|
};
|
|
};
|
|
|
|
soc {
|
|
/* Name the GPIO muxed rails on the Snowball board */
|
|
gpio@8012e000 {
|
|
/* GPIOs 0 - 31 */
|
|
gpio-line-names = "", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "",
|
|
"AP_GPIO31";
|
|
};
|
|
|
|
gpio@8012e080 {
|
|
/* GPIOs 32 - 63 */
|
|
gpio-line-names = "USR PB", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "";
|
|
};
|
|
|
|
gpio@8000e000 {
|
|
/* GPIOs 64 - 95 */
|
|
gpio-line-names = "", "", "", "", "AP_GPIO68", "", "", "",
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "";
|
|
};
|
|
|
|
gpio@8000e100 {
|
|
/* GPIOs 128 - 159 */
|
|
gpio-line-names = "", "", "", "", "", "", "", "",
|
|
"", "", "", "", "IRQ_LAN", "RSTn_LAN",
|
|
"USR_LED", "", "", "", "", "", "",
|
|
"", "", "AP_GPIO151", "AP_GPIO152",
|
|
"", "", "", "", "", "", "";
|
|
};
|
|
|
|
gpio@8000e180 {
|
|
/* GPIOs 160 - 191 */
|
|
gpio-line-names = "", "AP_GPIO161", "AP_GPIO162",
|
|
"ACCELEROMETER_INT1_RDY",
|
|
"ACCELEROMETER_INT2", "MAG_DRDY",
|
|
"GYRO_DRDY", "RSTn_MLC", "RSTn_SLC",
|
|
"GYRO_INT", "UART_WAKE", "GBF_RESET",
|
|
"", "", "", "",
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "";
|
|
};
|
|
|
|
gpio@8011e000 {
|
|
/* GPIOs 192 - 223 */
|
|
gpio-line-names = "HDTV_INTn", "", "", "", "HDTV_RST",
|
|
"", "", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "", "",
|
|
"WLAN_RESETN", "WLAN_IRQ", "MMC_EN",
|
|
"MMC_CD", "", "", "", "", "";
|
|
};
|
|
|
|
gpio@8011e080 {
|
|
/* GPIOs 224 - 255 */
|
|
gpio-line-names = "", "", "", "", "SD_SEL", "", "", "",
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "";
|
|
};
|
|
|
|
usb_per5@a03e0000 {
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&musb_default_mode>;
|
|
pinctrl-1 = <&musb_sleep_mode>;
|
|
};
|
|
|
|
sound {
|
|
compatible = "stericsson,snd-soc-mop500";
|
|
|
|
stericsson,cpu-dai = <&msp1 &msp3>;
|
|
stericsson,audio-codec = <&codec>;
|
|
};
|
|
|
|
msp0: msp@80123000 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&msp0_default_mode>;
|
|
status = "okay";
|
|
};
|
|
|
|
msp1: msp@80124000 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&msp1_default_mode>;
|
|
status = "okay";
|
|
};
|
|
|
|
msp2: msp@80117000 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&msp2_default_mode>;
|
|
};
|
|
|
|
msp3: msp@80125000 {
|
|
status = "okay";
|
|
};
|
|
|
|
external-bus@50000000 {
|
|
status = "okay";
|
|
|
|
ethernet@0 {
|
|
compatible = "smsc,lan9115";
|
|
reg = <0 0x10000>;
|
|
interrupts = <12 IRQ_TYPE_EDGE_RISING>;
|
|
interrupt-parent = <&gpio4>;
|
|
vdd33a-supply = <&en_3v3_reg>;
|
|
vddvario-supply = <&db8500_vape_reg>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <ð_snowball_mode>;
|
|
|
|
reg-shift = <1>;
|
|
reg-io-width = <2>;
|
|
smsc,force-internal-phy;
|
|
smsc,irq-active-high;
|
|
smsc,irq-push-pull;
|
|
|
|
clocks = <&prcc_pclk 3 0>;
|
|
};
|
|
};
|
|
|
|
vmmci: regulator-gpio {
|
|
compatible = "regulator-gpio";
|
|
|
|
gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>;
|
|
enable-gpio = <&gpio6 25 GPIO_ACTIVE_HIGH>;
|
|
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <2900000>;
|
|
regulator-name = "mmci-reg";
|
|
regulator-type = "voltage";
|
|
|
|
startup-delay-us = <100>;
|
|
enable-active-high;
|
|
|
|
states = <1800000 0x1
|
|
2900000 0x0>;
|
|
};
|
|
|
|
// External Micro SD slot
|
|
sdi0_per1@80126000 {
|
|
arm,primecell-periphid = <0x10480180>;
|
|
max-frequency = <100000000>;
|
|
bus-width = <4>;
|
|
cap-sd-highspeed;
|
|
cap-mmc-highspeed;
|
|
sd-uhs-sdr12;
|
|
sd-uhs-sdr25;
|
|
/* All direction control is used */
|
|
st,sig-dir-cmd;
|
|
st,sig-dir-dat0;
|
|
st,sig-dir-dat2;
|
|
st,sig-dir-dat31;
|
|
st,sig-pin-fbclk;
|
|
full-pwr-cycle;
|
|
vmmc-supply = <&ab8500_ldo_aux3_reg>;
|
|
vqmmc-supply = <&vmmci>;
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&sdi0_default_mode>;
|
|
pinctrl-1 = <&sdi0_sleep_mode>;
|
|
|
|
/* GPIO218 MMC_CD */
|
|
cd-gpios = <&gpio6 26 GPIO_ACTIVE_LOW>;
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
// WLAN SDIO channel
|
|
sdi1_per2@80118000 {
|
|
arm,primecell-periphid = <0x10480180>;
|
|
max-frequency = <100000000>;
|
|
bus-width = <4>;
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&sdi1_default_mode>;
|
|
pinctrl-1 = <&sdi1_sleep_mode>;
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
// Unused PoP eMMC - register and put it to sleep by default */
|
|
sdi2_per3@80005000 {
|
|
arm,primecell-periphid = <0x10480180>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&sdi2_sleep_mode>;
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
// On-board eMMC
|
|
sdi4_per2@80114000 {
|
|
arm,primecell-periphid = <0x10480180>;
|
|
max-frequency = <100000000>;
|
|
bus-width = <8>;
|
|
cap-mmc-highspeed;
|
|
vmmc-supply = <&ab8500_ldo_aux2_reg>;
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&sdi4_default_mode>;
|
|
pinctrl-1 = <&sdi4_sleep_mode>;
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
uart@80120000 {
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&uart0_default_mode>;
|
|
pinctrl-1 = <&uart0_sleep_mode>;
|
|
status = "okay";
|
|
};
|
|
|
|
/* This UART is unused and thus left disabled */
|
|
uart@80121000 {
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&uart1_default_mode>;
|
|
pinctrl-1 = <&uart1_sleep_mode>;
|
|
};
|
|
|
|
uart@80007000 {
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&uart2_default_mode>;
|
|
pinctrl-1 = <&uart2_sleep_mode>;
|
|
status = "okay";
|
|
};
|
|
|
|
i2c@80004000 {
|
|
pinctrl-names = "default","sleep";
|
|
pinctrl-0 = <&i2c0_default_mode>;
|
|
pinctrl-1 = <&i2c0_sleep_mode>;
|
|
};
|
|
|
|
i2c@80122000 {
|
|
pinctrl-names = "default","sleep";
|
|
pinctrl-0 = <&i2c1_default_mode>;
|
|
pinctrl-1 = <&i2c1_sleep_mode>;
|
|
};
|
|
|
|
i2c@80128000 {
|
|
pinctrl-names = "default","sleep";
|
|
pinctrl-0 = <&i2c2_default_mode>;
|
|
pinctrl-1 = <&i2c2_sleep_mode>;
|
|
lsm303dlh@18 {
|
|
/* Accelerometer */
|
|
compatible = "st,lsm303dlh-accel";
|
|
st,drdy-int-pin = <1>;
|
|
reg = <0x18>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&accel_snowball_mode>;
|
|
interrupt-parent = <&gpio5>;
|
|
interrupts = <3 IRQ_TYPE_EDGE_RISING>, /* INT1 */
|
|
<4 IRQ_TYPE_EDGE_RISING>; /* INT2 */
|
|
};
|
|
lsm303dlh@1e {
|
|
/* Magnetometer */
|
|
compatible = "st,lsm303dlh-magn";
|
|
reg = <0x1e>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&magneto_snowball_mode>;
|
|
interrupt-parent = <&gpio5>;
|
|
interrupts = <5 IRQ_TYPE_EDGE_RISING>; /* DRDY line */
|
|
};
|
|
l3g4200d@68 {
|
|
/* Gyroscope */
|
|
compatible = "st,l3g4200d-gyro";
|
|
st,drdy-int-pin = <2>;
|
|
reg = <0x68>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&gyro_snowball_mode>;
|
|
interrupt-parent = <&gpio5>;
|
|
interrupts = <6 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
|
|
<9 IRQ_TYPE_EDGE_RISING>; /* INT1 */
|
|
};
|
|
lsp001wm@5c {
|
|
/* Barometer/pressure sensor */
|
|
compatible = "st,lps001wp-press";
|
|
reg = <0x5c>;
|
|
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
|
vddio-supply = <&db8500_vsmps2_reg>;
|
|
};
|
|
};
|
|
|
|
i2c@80110000 {
|
|
pinctrl-names = "default","sleep";
|
|
pinctrl-0 = <&i2c3_default_mode>;
|
|
pinctrl-1 = <&i2c3_sleep_mode>;
|
|
};
|
|
|
|
ssp@80002000 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&ssp0_snowball_mode>;
|
|
};
|
|
|
|
cpufreq-cooling {
|
|
status = "okay";
|
|
};
|
|
|
|
prcmu@80157000 {
|
|
cpufreq {
|
|
status = "okay";
|
|
};
|
|
|
|
thermal@801573c0 {
|
|
num-trips = <4>;
|
|
|
|
trip0-temp = <70000>;
|
|
trip0-type = "active";
|
|
trip0-cdev-num = <1>;
|
|
trip0-cdev-name0 = "thermal-cpufreq-0";
|
|
|
|
trip1-temp = <75000>;
|
|
trip1-type = "active";
|
|
trip1-cdev-num = <1>;
|
|
trip1-cdev-name0 = "thermal-cpufreq-0";
|
|
|
|
trip2-temp = <80000>;
|
|
trip2-type = "active";
|
|
trip2-cdev-num = <1>;
|
|
trip2-cdev-name0 = "thermal-cpufreq-0";
|
|
|
|
trip3-temp = <85000>;
|
|
trip3-type = "critical";
|
|
trip3-cdev-num = <0>;
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
ab8500 {
|
|
ab8500-gpio {
|
|
/*
|
|
* AB8500 GPIOs are numbered starting from 1, so the first
|
|
* index 0 is what in the datasheet is called "GPIO1", and
|
|
* the second is "GPIO2" and so forth. Confusingly, the
|
|
* Snowball schematic then names the "GPIO2" line "PM_GPIO1".
|
|
* while later naming "GPIO4" as "PM_GPIO4".
|
|
*/
|
|
gpio-line-names = "", /* AB8500 GPIO1 */
|
|
"PM_GPIO1", /* AB8500 GPIO2 */
|
|
"WLAN_CLK_REQ", /* AB8500 GPIO3 */
|
|
"PM_GPIO4", /* AB8500 GPIO4 */
|
|
"", "", "", "", "", "", "", "", "", "", "",
|
|
"EN_3V6", /* AB8500 GPIO16 */
|
|
"", "", "", "" ,"", "", "", "", "",
|
|
"EN_3V3", /* AB8500 GPIO26 */
|
|
"", "", "", "", "", "", "", "", "", "", "", "", "",
|
|
"PM_GPIO40", /* AB8500 GPIO40 */
|
|
"PM_GPIO41", /* AB8500 GPIO41 */
|
|
"PM_GPIO42"; /* AB8500 GPIO42 */
|
|
};
|
|
|
|
ext_regulators: ab8500-ext-regulators {
|
|
ab8500_ext1_reg: ab8500_ext1 {
|
|
regulator-name = "ab8500-ext-supply1";
|
|
};
|
|
|
|
ab8500_ext2_reg_reg: ab8500_ext2 {
|
|
regulator-name = "ab8500-ext-supply2";
|
|
};
|
|
|
|
ab8500_ext3_reg_reg: ab8500_ext3 {
|
|
regulator-name = "ab8500-ext-supply3";
|
|
};
|
|
};
|
|
|
|
ab8500-regulators {
|
|
ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
|
|
regulator-name = "V-DISPLAY";
|
|
};
|
|
|
|
ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
|
|
regulator-name = "V-eMMC1";
|
|
};
|
|
|
|
ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
|
|
regulator-name = "V-MMC-SD";
|
|
};
|
|
|
|
ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
|
|
regulator-name = "V-INTCORE";
|
|
};
|
|
|
|
ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
|
|
regulator-name = "V-TVOUT";
|
|
};
|
|
|
|
ab8500_ldo_usb_reg: ab8500_ldo_usb {
|
|
regulator-name = "dummy";
|
|
};
|
|
|
|
ab8500_ldo_audio_reg: ab8500_ldo_audio {
|
|
regulator-name = "V-AUD";
|
|
};
|
|
|
|
ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
|
|
regulator-name = "V-AMIC1";
|
|
};
|
|
|
|
ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
|
|
regulator-name = "V-AMIC2";
|
|
};
|
|
|
|
ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
|
|
regulator-name = "V-DMIC";
|
|
};
|
|
|
|
ab8500_ldo_ana_reg: ab8500_ldo_ana {
|
|
regulator-name = "V-CSI/DSI";
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
pinctrl {
|
|
/*
|
|
* Set this up using hogs, as time goes by and as seems fit, these
|
|
* can be moved over to being controlled by respective device.
|
|
*/
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&gbf_snowball_mode>,
|
|
<&wlan_snowball_mode>;
|
|
|
|
ethernet {
|
|
/*
|
|
* Mux in "SM" which is used for the
|
|
* SMSC911x Ethernet adapter
|
|
*/
|
|
eth_snowball_mode: eth_snowball {
|
|
snowball_mux {
|
|
function = "sm";
|
|
groups = "sm_b_1";
|
|
};
|
|
/* LAN IRQ pin */
|
|
snowball_cfg1 {
|
|
pins = "GPIO140_B11";
|
|
ste,config = <&in_nopull>;
|
|
};
|
|
/* LAN reset pin */
|
|
snowball_cfg2 {
|
|
pins = "GPIO141_C12";
|
|
ste,config = <&gpio_out_hi>;
|
|
};
|
|
|
|
};
|
|
};
|
|
sdi0 {
|
|
sdi0_default_mode: sdi0_default {
|
|
snowball_mux {
|
|
function = "mc0";
|
|
groups = "mc0dat31dir_a_1";
|
|
};
|
|
snowball_cfg1 {
|
|
pins = "GPIO21_AB3"; /* DAT31DIR */
|
|
ste,config = <&out_hi>;
|
|
};
|
|
/* SD card detect GPIO pin, extend default state */
|
|
snowball_cfg2 {
|
|
pins = "GPIO218_AH11";
|
|
ste,config = <&gpio_in_pu>;
|
|
};
|
|
/* VMMCI level-shifter enable */
|
|
snowball_cfg3 {
|
|
pins = "GPIO217_AH12";
|
|
ste,config = <&gpio_out_hi>;
|
|
};
|
|
/* VMMCI level-shifter voltage select */
|
|
snowball_cfg4 {
|
|
pins = "GPIO228_AJ6";
|
|
ste,config = <&gpio_out_hi>;
|
|
};
|
|
};
|
|
};
|
|
ssp0 {
|
|
ssp0_snowball_mode: ssp0_snowball_default {
|
|
snowball_mux {
|
|
function = "ssp0";
|
|
groups = "ssp0_a_1";
|
|
};
|
|
snowball_cfg1 {
|
|
pins = "GPIO144_B13"; /* FRM */
|
|
ste,config = <&gpio_out_hi>;
|
|
};
|
|
snowball_cfg2 {
|
|
pins = "GPIO145_C13"; /* RXD */
|
|
ste,config = <&in_pd>;
|
|
};
|
|
snowball_cfg3 {
|
|
pins =
|
|
"GPIO146_D13", /* TXD */
|
|
"GPIO143_D12"; /* CLK */
|
|
ste,config = <&out_lo>;
|
|
};
|
|
|
|
};
|
|
};
|
|
gpio_led {
|
|
gpioled_snowball_mode: gpioled_default {
|
|
snowball_cfg1 {
|
|
pins = "GPIO142_C11";
|
|
ste,config = <&gpio_out_hi>;
|
|
};
|
|
|
|
};
|
|
};
|
|
accelerometer {
|
|
accel_snowball_mode: accel_snowball {
|
|
/* Accelerometer lines */
|
|
snowball_cfg1 {
|
|
pins =
|
|
"GPIO163_C20", /* ACCEL_IRQ1 */
|
|
"GPIO164_B21"; /* ACCEL_IRQ2 */
|
|
ste,config = <&gpio_in_pu>;
|
|
};
|
|
};
|
|
};
|
|
gyro {
|
|
gyro_snowball_mode: gyro_snowball {
|
|
snowball_cfg1 {
|
|
pins =
|
|
"GPIO166_A22", /* DRDY */
|
|
"GPIO169_D22"; /* INT */
|
|
ste,config = <&gpio_in_pu>;
|
|
};
|
|
};
|
|
};
|
|
magnetometer {
|
|
magneto_snowball_mode: magneto_snowball {
|
|
snowball_cfg1 {
|
|
pins = "GPIO165_C21"; /* MAG_DRDY */
|
|
ste,config = <&gpio_in_pu>;
|
|
};
|
|
};
|
|
};
|
|
gbf {
|
|
gbf_snowball_mode: gbf_snowball {
|
|
/*
|
|
* GBF (GPS, Bluetooth, FM-radio) interface,
|
|
* pull low to reset state
|
|
*/
|
|
snowball_cfg1 {
|
|
pins = "GPIO171_D23"; /* GBF_ENA_RESET */
|
|
ste,config = <&gpio_out_lo>;
|
|
};
|
|
};
|
|
};
|
|
wlan {
|
|
wlan_snowball_mode: wlan_snowball {
|
|
/*
|
|
* Activate this mode with the WLAN chip.
|
|
* These are plain GPIO pins used by WLAN
|
|
*/
|
|
snowball_cfg1 {
|
|
pins =
|
|
"GPIO161_D21", /* WLAN_PMU_EN */
|
|
"GPIO215_AH13"; /* WLAN_ENA */
|
|
ste,config = <&gpio_out_lo>;
|
|
};
|
|
snowball_cfg2 {
|
|
pins = "GPIO216_AG12"; /* WLAN_IRQ */
|
|
ste,config = <&gpio_in_pu>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
mcde@a0350000 {
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&lcd_default_mode>;
|
|
pinctrl-1 = <&lcd_sleep_mode>;
|
|
};
|
|
};
|
|
};
|