mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-12-28 05:24:47 +08:00
84e0cdb0a2
Both at91 and avr32 defines its own platform data structure for the macb driver and both share common structures though at91 includes a currently unused phy_irq_pin. Create a common macb_platform_data for macb that both at91 and avr32 can use. In future we can use this to support other architectures that use the same IP block with the macb driver. v2: rename eth_platform_data to macb_platform_data and allow at91_ether to share the platform data with macb. Signed-off-by: Jamie Iles <jamie@jamieiles.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
183 lines
4.5 KiB
C
183 lines
4.5 KiB
C
/*
|
|
* linux/arch/arm/mach-at91/board-cpuat91.c
|
|
*
|
|
* Copyright (C) 2009 Eric Benard - eric@eukrea.com
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
|
|
*/
|
|
|
|
#include <linux/types.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/init.h>
|
|
#include <linux/mm.h>
|
|
#include <linux/module.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/mtd/physmap.h>
|
|
#include <linux/mtd/plat-ram.h>
|
|
|
|
#include <mach/hardware.h>
|
|
#include <asm/setup.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/irq.h>
|
|
|
|
#include <asm/mach/arch.h>
|
|
#include <asm/mach/map.h>
|
|
#include <asm/mach/irq.h>
|
|
|
|
#include <mach/board.h>
|
|
#include <mach/at91rm9200_mc.h>
|
|
#include <mach/cpu.h>
|
|
|
|
#include "generic.h"
|
|
|
|
static struct gpio_led cpuat91_leds[] = {
|
|
{
|
|
.name = "led1",
|
|
.default_trigger = "heartbeat",
|
|
.active_low = 1,
|
|
.gpio = AT91_PIN_PC0,
|
|
},
|
|
};
|
|
|
|
static void __init cpuat91_init_early(void)
|
|
{
|
|
/* Set cpu type: PQFP */
|
|
at91rm9200_set_type(ARCH_REVISON_9200_PQFP);
|
|
|
|
/* Initialize processor: 18.432 MHz crystal */
|
|
at91_initialize(18432000);
|
|
|
|
/* DBGU on ttyS0. (Rx & Tx only) */
|
|
at91_register_uart(0, 0, 0);
|
|
|
|
/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
|
|
at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS |
|
|
ATMEL_UART_RTS);
|
|
|
|
/* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
|
|
at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS |
|
|
ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR |
|
|
ATMEL_UART_DCD | ATMEL_UART_RI);
|
|
|
|
/* USART2 on ttyS3 (Rx, Tx) */
|
|
at91_register_uart(AT91RM9200_ID_US2, 3, 0);
|
|
|
|
/* USART3 on ttyS4 (Rx, Tx, CTS, RTS) */
|
|
at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_CTS |
|
|
ATMEL_UART_RTS);
|
|
|
|
/* set serial console to ttyS0 (ie, DBGU) */
|
|
at91_set_serial_console(0);
|
|
}
|
|
|
|
static struct macb_platform_data __initdata cpuat91_eth_data = {
|
|
.is_rmii = 1,
|
|
};
|
|
|
|
static struct at91_usbh_data __initdata cpuat91_usbh_data = {
|
|
.ports = 1,
|
|
};
|
|
|
|
static struct at91_udc_data __initdata cpuat91_udc_data = {
|
|
.vbus_pin = AT91_PIN_PC15,
|
|
.pullup_pin = AT91_PIN_PC14,
|
|
};
|
|
|
|
static struct at91_mmc_data __initdata cpuat91_mmc_data = {
|
|
.det_pin = AT91_PIN_PC2,
|
|
.wire4 = 1,
|
|
};
|
|
|
|
static struct physmap_flash_data cpuat91_flash_data = {
|
|
.width = 2,
|
|
};
|
|
|
|
static struct resource cpuat91_flash_resource = {
|
|
.start = AT91_CHIPSELECT_0,
|
|
.end = AT91_CHIPSELECT_0 + SZ_16M - 1,
|
|
.flags = IORESOURCE_MEM,
|
|
};
|
|
|
|
static struct platform_device cpuat91_norflash = {
|
|
.name = "physmap-flash",
|
|
.id = 0,
|
|
.dev = {
|
|
.platform_data = &cpuat91_flash_data,
|
|
},
|
|
.resource = &cpuat91_flash_resource,
|
|
.num_resources = 1,
|
|
};
|
|
|
|
#ifdef CONFIG_MTD_PLATRAM
|
|
struct platdata_mtd_ram at91_sram_pdata = {
|
|
.mapname = "SRAM",
|
|
.bankwidth = 2,
|
|
};
|
|
|
|
static struct resource at91_sram_resource[] = {
|
|
[0] = {
|
|
.start = AT91RM9200_SRAM_BASE,
|
|
.end = AT91RM9200_SRAM_BASE + AT91RM9200_SRAM_SIZE - 1,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
};
|
|
|
|
static struct platform_device at91_sram = {
|
|
.name = "mtd-ram",
|
|
.id = 0,
|
|
.resource = at91_sram_resource,
|
|
.num_resources = ARRAY_SIZE(at91_sram_resource),
|
|
.dev = {
|
|
.platform_data = &at91_sram_pdata,
|
|
},
|
|
};
|
|
#endif /* MTD_PLATRAM */
|
|
|
|
static struct platform_device *platform_devices[] __initdata = {
|
|
&cpuat91_norflash,
|
|
#ifdef CONFIG_MTD_PLATRAM
|
|
&at91_sram,
|
|
#endif /* CONFIG_MTD_PLATRAM */
|
|
};
|
|
|
|
static void __init cpuat91_board_init(void)
|
|
{
|
|
/* Serial */
|
|
at91_add_device_serial();
|
|
/* LEDs. */
|
|
at91_gpio_leds(cpuat91_leds, ARRAY_SIZE(cpuat91_leds));
|
|
/* Ethernet */
|
|
at91_add_device_eth(&cpuat91_eth_data);
|
|
/* USB Host */
|
|
at91_add_device_usbh(&cpuat91_usbh_data);
|
|
/* USB Device */
|
|
at91_add_device_udc(&cpuat91_udc_data);
|
|
/* MMC */
|
|
at91_add_device_mmc(0, &cpuat91_mmc_data);
|
|
/* I2C */
|
|
at91_add_device_i2c(NULL, 0);
|
|
/* Platform devices */
|
|
platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
|
|
}
|
|
|
|
MACHINE_START(CPUAT91, "Eukrea")
|
|
/* Maintainer: Eric Benard - EUKREA Electromatique */
|
|
.timer = &at91rm9200_timer,
|
|
.map_io = at91_map_io,
|
|
.init_early = cpuat91_init_early,
|
|
.init_irq = at91_init_irq_default,
|
|
.init_machine = cpuat91_board_init,
|
|
MACHINE_END
|